Effect of pro-oxidant concentration on characteristics of packaging films of cobalt stearate filled polypropylene

2020 ◽  
Vol 40 (8) ◽  
pp. 637-646
Author(s):  
Sunil Sable ◽  
Sanjeev Ahuja ◽  
Haripada Bhunia
Keyword(s):  
Morphological Properties ◽  
Test Plant ◽  
Compression Moulding ◽  
Scanning Calorimetry ◽  
Flexible Packaging ◽  
Oxidant Concentration ◽  
Before And After ◽  
Twin Screw ◽  
Degraded Material ◽  
The Cost

AbstractIn this work, polypropylene (PP) filled with different proportions of CoSt were prepared in a twin-screw extruder by compounding technique. Eight films of these compounds were prepared using compression moulding. The modified PP films were characterized for chemical, physical, thermal, and morphological properties (before and after biodegradation). The biodegradation of the CoSt filled PP films was studied under controlled composting conditions, and the degradation intermediates were evaluated for their ecotoxicological impact. The CoSt present in the PP film was confirmed by Fourier transform infrared spectroscopy. As the addition of CoSt was progressively increased, the tensile strength and thermal stability decreased as shown by UTM and thermogravimetric analysis. The compounding of CoSt in PP reduced its crystallinity as revealed by the differential scanning calorimetry and X-ray diffraction analysis, and this led to enhanced degradation of PP. After biodegradation, SEM results of modified PP films showed rougher morphology than before biodegradation. The maximum biodegradation (19.78%) was shown by the film having 2 phr CoSt. The ecotoxicity tests of the degraded material, namely, microbial test, plant growth test, and earthworm acute-toxicity test demonstrated that the biodegradation intermediates were nontoxic. Hence, CoSt filled PP has high industrial potential to make biodegradable flexible packaging.

Effect of Compatibilizers on Mechanical Thermal and Morphology Properties of HDPE/TiO2 Nanocomposites

2010 ◽  
Vol 93-94 ◽  
pp. 169-172
Author(s):  
N. Wiriyanukul ◽  
S. Wacharawichanant
Keyword(s):  
Tensile Strength ◽  
Electron Microscope ◽  
High Density Polyethylene ◽  
Morphological Properties ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Before And After ◽  
Twin Screw ◽  
Dispersion Of Nanoparticles ◽  
Scanning Electron

This work studies the effect of PE-g-MA compatibilizer on mechanical thermal and morphological properties of high density polyethylene (HDPE)/titanium dioxide (TiO2) nanocomposites. The HDPE/TiO2 nanocomposites with and without PE-g-MA compatibilizer were prepared by melt mixing technique in a twin screw extruder. The results found that Young's Modulus of HDPE/TiO2 nanocomposites increased with increasing TiO2 contents. The addition of PE-g-MA compatibilizer had no significant effect on the tensile strength and stress at break of HDPE/TiO2 nanocomposites. The decomposition temperatures of HDPE/TiO2 nanocomposites before and after adding PE-g-MA compatibilizer increased with increasing TiO2 contents. The dispersion of TiO2 nanoparticles in HDPE matrix was observed by scanning electron microscope (SEM). The dispersion of nanoparticles in HDPE matrix with PE-g-MA compatibilizer was relatively good, only a few aggregates exited.

Studies on Tensile Properties of Compatibilized and Uncompatibilized Low-Density Polyethylene/Jackfruit Seed Flour (LDPE/JFSF) Blends at Different JFSF Content

2017 ◽  
Vol 264 ◽  
pp. 120-123 ◽  
Author(s):  
Sung Ting Sam ◽  
Omar Sabbar Dahham ◽  
Pei Gie Gan ◽  
N.Z. Noimam ◽  
Jingi Y. Kuan ◽  
...  
Keyword(s):  
Tensile Properties ◽  
Adipic Acid ◽  
Morphological Properties ◽  
Screw Extruder ◽  
Direct Introduction ◽  
Elongation At Break ◽  
Seed Flour ◽  
Before And After ◽  
Twin Screw ◽  
Natural Fillers

Currently, natural fillers seem to be the suitable materials in polymer industry, which have emerged as a viable and abundant replacement for the relatively high-cost and non-renewable conventional fillers. However, the direct introduction of natural fillers into polymer matrix could effect negatively on some properties. Therefore, the aim of this work is to evaluate the influence of jackfruit seed flour (JFSF) (before and after compatibilization) on the tensile properties of (LDPE/JFSF) blends. Different JFSF content (5, 10, 15 and 20 wt.%) with (63-100 𝜇𝑚) particle size were prepared in this work. Twin-screw extruder at 150°C and 50rpm screw speed followed by hot-compress machine at 150°C and 10MPa pressure were used respectively to produce (LDPE/JFSF) blends. Adipic acid (AA) solution was added as a compatibilizer into all blends equally (25wt% AA into 75wt% JFSf). The changes of tensile and morphological properties were investigated. Results shown decreasing on tensile strength and elongation at break of LDPE/JFSF and LDPE/JFSF/AA as JFSF increased. In contrast, Young’s modulus increased up to 10 wt.% of JFSF and then decreased. However, the addition of Adipic acid, particularly for JFSF 5wt.% has improved the tensile properties of LDPE/JFSF blends. The SEM micrographs showed the agglomeration at high JFSF content (20 wt%) which in turn effected negatively on the tensile properties. However, the blends show homogeneous surfaces as AA added.

Effect of the Citric Acid as Blowing Agent on the Compressive Properties and Morphology of PLA/ENR Blend Foams

2017 ◽  
Vol 873 ◽  
pp. 95-100
Author(s):  
Sumate Ouipanich ◽  
Thiti Kaisone ◽  
Pran Hanthanon ◽  
Chanon Wiphanurat ◽  
Yupawan Thongjun ◽  
...  
Keyword(s):  
Citric Acid ◽  
Testing Machine ◽  
Morphological Properties ◽  
Compressive Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Blowing Agents ◽  
Universal Testing ◽  
Hydrogen Carbonate ◽  
Twin Screw

The effect of a blowing agents that affected Polylactic acid (PLA) and Epoxidized natural rubber (ENR) the blowing agents composed of citric acid (CA) and sodium hydrogen carbonate (NaHCO3) mixing by twin screw extruder with co-rotation screw. The properties of biodegradable foams were investigated. Blended foams of all composition were prepared by using compression molding at 200°C using different proportions of PLA, ENR, CA and NaHCO3. Mechanical properties of the samples were characterized by using universal testing machine. Thermal properties including Glass transition temperature (Tg), crystallization temperature (Tc) and melting temperature (Tm) were examined by using differential scanning calorimetry (DSC). Physical properties including morphology and density of blended foams were also investigated and morphological properties were studied with a scanning electron microscope (SEM).

Injectable in-situ Forming Depot Of Doxycycline Hyclate/α-Cyclodextrin Complex using PLGA for Periodontitis Treatment: Preparation, Charac-terization, and In-Vitro Evaluation

2020 ◽  
Vol 17 ◽  
Author(s):  
Elham Khodaverdi ◽  
Farhad Eisvand ◽  
Mohammad Sina Nezami ◽  
Seyedeh Nesa Rezaeian Shiadeh ◽  
Hossein Kamali ◽  
...  
Keyword(s):  
Complex Form ◽  
Docking Studies ◽  
Morphological Properties ◽  
Burst Release ◽  
Cyclodextrin Complex ◽  
Doxycycline Hyclate ◽  
Scanning Calorimetry ◽  
In Situ Forming

Background:: Doxycycline (DOX) is used in treating a bacterial infection, especially for periodontitis treatment. Objective: To reduce irritation of DOX for subgingival administration and increase the chemical stability and against enzy-matic, the complex of α-cyclodextrin with DOX was prepared and loaded into injectable in situ forming implant based on PLGA. Methods:: FTIR, molecular docking studies, X-ray diffraction, and differential scanning calorimetry was performed to char-acterize the DOX/α-cyclodextrin complex. Finally, the in-vitro drug release and modeling, morphological properties, and cellular cytotoxic effects were also evaluated. Results:: The stability of DOX was improved with complex than pure DOX. The main advantage of the complex is the al-most complete release (96.31 ± 2.56 %) of the drug within 14 days of the implant, whereas in the formulation containing the pure DOX and the physical mixture the DOX with α-cyclodextrin release is reached to 70.18 ± 3.61 % and 77.03 ± 3.56 %, respectively. This trend is due to elevate of DOX stability in the DOX/ α-cyclodextrin complex form within PLGA implant that confirmed by the results of stability. Conclusion:: Our results were indicative that the formulation containing DOX/α-cyclodextrin complex was biocompatible and sustained-release with minimum initial burst release.

Characterization of Nostoc muscorum NCCU-442 Derived Poly-3- hydroxybutyrate (PHB) and Polyethylene Glycol (PEG) Blends

2020 ◽  
Vol 10 (3) ◽  
pp. 200-207
Author(s):  
Sabbir Ansari ◽  
Tasneem Fatma
Keyword(s):  
Thermal Properties ◽  
Polyethylene Glycol ◽  
Morphological Properties ◽  
Morphological Alteration ◽  
Nostoc Muscorum ◽  
Microbial Culture ◽  
Polymer Science ◽  
Mixed Microbial Culture ◽  
Scanning Calorimetry ◽  
Casting Technique

Background: Poly-3-hydroxybutyrate (PHB) has attracted much consideration as biodegradable biocompatible polymer. This thermoplastic polymer has comparable material properties to polypropylene. Materials with more valuable properties may result from blending, a common practice in polymer science. Objective: In this paper, blends of PHB (extracted from cyanobacterium Nostoc muscorum NCCU- 442 with polyethylene glycol (PEG) were investigated for their thermal, tensile, hydrophilic and biodegradation properties. Methods: Blends were prepared in different proportions of PHB/PEG viz. 100/0, 98/2, 95/5, 90/10, 80/20, and 70/30 (wt %) using solvent casting technique. Morphological properties were investigated by using Scanning Electron Microscopy (SEM). Differential scanning calorimetry and thermogravimetric analysis were done for thermal properties determination whereas the mechanical and hydrophilic properties of the blends were studied by means of an automated material testing system and contact angle analyser respectively. Biodegradability potential of the blended films was tested as percent weight loss by mixed microbial culture within 60 days. Results: The blends showed good misciblity between PEG and PHB, however increasing concentrations of plasticizer caused morphological alteration as evidenced by SEM micrographs. PEG addition (10 % and above) showed significant alternations in the thermal properties of the blends. Increase in the PEG content increased the elongation at break ratio i.e enhanced the required plasticity of PHB. Rate of microbial facilitated degradation of the blends was greater with increasing PEG concentrations. Conclusion: Blending with PEG increased the crucial polymeric properties of cyanobacterial PHB.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

Behaviour of PLA/POSS nanocomposites: Effects of filler content, functional group and copolymer compatibilization

2021 ◽  
pp. 096739112110080
Author(s):  
Yelda Meyva Zeybek ◽  
Cevdet Kaynak
Keyword(s):  
Functional Group ◽  
Filler Content ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Grafted Copolymer ◽  
Before And After ◽  
Twin Screw ◽  
Oligomeric Silsesquioxane ◽  
Matrix Nanocomposites

The main purpose of this study was to investigate influences of three parameters on the mechanical and thermal properties of the polylactide (PLA) matrix nanocomposites filled with polyhedral oligomeric silsesquioxane (POSS) particles. For the first parameter of “Filler Content”, nanocomposites with 1, 3, 5, 7 wt% basic POSS structure were compared. For the second parameter of “Functional Group,” basic POSS structure having only nonpolar isobutyl groups were compared with three other functionalized POSS structures; i.e. aminopropylisobutyl-POSS (ap-POSS), propanediolisobutyl-POSS (pd-POSS) and octasilane-POSS (os-POSS). Finally, for the third parameter of “Copolymer Compatibilization,” all specimens were compared before and after their maleic anhydride (MA) grafted copolymer compatibilization. Specimens were produced with twin-screw extruder melt mixing and shaped under compression molding. Various tests and analyses indicated that the optimum filler content for the improved mechanical properties was 1 wt%; while the optimum structure for strength and modulus was pd-POSS structure, in terms of fracture toughness it was basic POSS structure. Additional use of MA compatibilization was especially effective for the basic POSS and os-POSS particles.

scholarly journals A Characteristic Study of Polylactic Acid/Organic Modified Montmorillonite (PLA/OMMT) Nanocomposite Materials after Hydrolyzing

Crystals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 376
Author(s):  
Su-Mei Huang ◽  
Jiunn-Jer Hwang ◽  
Hsin-Jiant Liu ◽  
An-Miao Zheng
Keyword(s):  
Thermal Stability ◽  
Polylactic Acid ◽  
Decomposition Temperature ◽  
Material Strength ◽  
Scanning Calorimetry ◽  
Hydrolysis Process ◽  
Twin Screw ◽  
Thermal Pressing ◽  
Organophilic Clay ◽  
Mmt Clay

In this study, the montmorillonite (MMT) clay was modified with NH4Cl, and then the structures were exfoliated or intercalated in a polylactic acid (PLA) matrix by a torque rheometer in the ratio of 0.5, 3.0, 5.0 and 8.0 wt%. X-ray diffraction (XRD) revealed that the organic modified-MMT(OMMT) was distributed successfully in the PLA matrix. After thermal pressing, the thermal stability of the mixed composites was measured by a TGA. The mixed composites were also blended with OMMT by a co-rotating twin screw extruder palletizing system, and then injected for the ASTM-D638 standard specimen by an injection machine for measuring the material strength by MTS. The experimental results showed that the mixture of organophilic clay and PLA would enhance the thermal stability. In the PLA mixed with 3 wt% OMMT nanocomposite, the TGA maximum decomposition temperature (Tmax) rose from 336.84 °C to 339.08 °C. In the PLA mixed with 5 wt% OMMT nanocomposite, the loss of temperature rose from 325.14 °C to 326.48 °C. In addition, the elongation rate increased from 4.46% to 10.19% with the maximum loading of 58 MPa. After the vibrating hydrolysis process, the PLA/OMMT nanocomposite was degraded through the measurement of differential scanning calorimetry (DSC) and its Tg, Tc, and Tm1 declined.

scholarly journals High-Tribological-Performance Polymer Nanocomposites: An Approach Based on the Superlubricity State of the Graphene Oxide Agglomerates

Polymers ◽  
2021 ◽  
Vol 13 (14) ◽  
pp. 2237
Author(s):  
Eder H. C. Ferreira ◽  
Angela Aparecida Vieira ◽  
Lúcia Vieira ◽  
Guilhermino J. M. Fechine
Keyword(s):  
Graphene Oxide ◽  
High Viscosity ◽  
Tribological Performance ◽  
Multilayer Graphene ◽  
High Concentration ◽  
Scanning Calorimetry ◽  
Mechanical Reinforcement ◽  
Transmission Electron ◽  
Twin Screw ◽  
Mechanical Tensile

Here, nanocomposites of high-molecular-weight polyethylene (HMWPE) and HMWPE-UHMWPE (80/20 wt.%) containing a low amount of multilayer graphene oxide (mGO) (≤0.1 wt.%) were produced via twin-screw extrusion to produce materials with a higher tribological performance than UHMWPE. Due to the high viscosity of both polymers, the nanocomposites presented a significant concentration of agglomerates. However, the mechanical (tensile) and tribological (volumetric loss) performances of the nanocomposites were superior to those of UHMWPE. The morphology of the nanocomposites was investigated using differential scanning calorimetry (DSC), microtomography, and transmission electron microscopy (TEM). The explanation for these results is based on the superlubricity phenomenon of mGO agglomerates. It was also shown that the well-exfoliated mGO also contained in the nanocomposite was of fundamental importance as a mechanical reinforcement for the polymer. Even with a high concentration of agglomerates, the nanocomposites displayed tribological properties superior to UHMWPE’s (wear resistance up to 27% higher and friction coefficient up to 57% lower). Therefore, this manuscript brings a new exception to the rule, showing that agglomerates can act in a beneficial way to the mechanical properties of polymers, as long as the superlubricity phenomenon is present in the agglomerates contained in the polymer.

scholarly journals Rheological, Thermal, Superficial, and Morphological Properties of Thermoplastic Achira Starch Modified with Lactic Acid and Oleic Acid

Molecules ◽  
2019 ◽  
Vol 24 (24) ◽  
pp. 4433 ◽  
Author(s):  
Carolina Caicedo ◽  
Rocío Yaneli Aguirre Loredo ◽  
Abril Fonseca García ◽  
Omar Hernán Ossa ◽  
Aldo Vázquez Arce ◽  
...  
Keyword(s):  
Lactic Acid ◽  
Oleic Acid ◽  
Complex Viscosity ◽  
Thermoplastic Starch ◽  
Residual Energy ◽  
Morphological Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Rheological Analysis ◽  
Acid Agent

The modification of achira starch a thermoplastic biopolymer is shown. Glycerol and sorbitol, common plasticizers, were used in the molten state with organic acids such as oleic acid and lactic acid obtaining thermodynamically more stable products. The proportion of starch:plasticizer was 70:30, and the acid agent was added in portions from 3%, 6%, and 9% by weight. These mixtures were obtained in a torque rheometer for 10 min at 130 °C. The lactic acid managed to efficiently promote the gelatinization process by increasing the available polar sites towards the surface of the material; as a result, there were lower values in the contact angle, these results were corroborated with the analysis performed by differential scanning calorimetry and X-ray diffraction. The results derived from oscillatory rheological analysis had a viscous behavior in the thermoplastic starch samples and with the presence of acids; this behavior favors the transitions from viscous to elastic. The mixture of sorbitol or glycerol with lactic acid promoted lower values of the loss module, the storage module, and the complex viscosity, which means lower residual energy in the transition of the viscous state to the elastic state; this allows the compounds to be scaled to conventional polymer transformation processes.

Sign in / Sign up

Export Citation Format

Share Document