Sources of Pollution of the Estuary of the River Nervion, Spain – A Case Study

1984 ◽  
Vol 16 (5-7) ◽  
pp. 95-125 ◽  
Author(s):  
A Azkona ◽  
S H Jenkins ◽  
H M G Roberts

This paper describes part of a comprehensive multidisciplinary study of the pollution of the estuary of the River Nervion, Bilbao, Spain. The objectives of the study were to determine the sources and loads of pollution from domestic sewage and industrial wastewater; provide information on the extent of pollution; formulate hydrodynamic and predictive models capable of forecasting the effects on the estuary of the anticipated growth of population and industry; determine the amount of polluting matter that would have to be removed in order to reach defined estuary water quality standards; arrive at suitable technical methods able to attain these standards at minimum cost; determine the treatability of wastewater discharges and recommend methods for controlling industrial wastewater. These objectives necessitated a survey of the pollution loads from domestic sources and industry which were discharged to the fresh water and tidal reaches of four major tributaries in addition to the main river Nervion; the results of this part of the survey are described in this paper. The presence of iron in discharges from iron ore mining and metal processing was found to aid flocculation of organic matter and the consequent deposition of sludge in the estuary. This action and the rate of oxygen uptake during the decomposition of such deposits are also described. The domestic sewage of the study area receives treatment in septic tanks before discharging to rivers or the estuary. In spite of free hydrogen sulphide and high concentrations being present in the septic tank effluents, odour nuisance does not occur, because, as is shown in the paper, of the formation of ferrous sulphide. The hydrogen sulphide concentration in the atmosphere at a pumping station was found to be above the safety level. The industrial load of impurity was estimated to be approximately 15% higher than the domestic load, but it is extremly difficult to find a rational basis on which comparisons may be made between domestic sewage and a mixture of industrial effluents containing substances inimical to biological activity. The industrial effluent was contained in a very large volume of water, much of it taken from the estuary for cooling or process water. It is calculated that if the industrial pollutants had been contained only in the fresh water used by industry the COD of the mixture would have been 1317 mg/l; the suspended solids 2143 mg/l; the ammonia nitrogen 191 mg/l; iron 1037 mg/l; other heavy metals 118 mg/l; fluoride as F 14.5 mg/l; cyanide as CN 8.1 mg/l; oil 196 mg/l; phenols 8.1 mg/l; mercury 0.13 mg/l; and the mixture would have had an excess of acidity of 5188 mg/l. An estimate of the load of substances having an oxygen demand indicated that of the total oxygen demand discharged to the system of rivers and estuary approximately 50% entered the estuary from the main tributaries, the remainder being discharged directly to the estuary. An outline is given of the methods that would be used to determine the treatability of industrial effluents which were rendered acceptable for discharge into public sewers.

The Common Effluent Treatment Plants (CETP) minimizes the pollution from industrial effluents. This plant monitors the reduction of physical and biochemical parameters such as total suspended solids (TSS), biological oxygen demand (BOD), chemical oxygen demand (COD), dissolved oxygen (DO), heavy metals etc. The Sequential Batch Reactor (SBR), a variation of the ASP, combines all the treatment steps and processes into a single basin. An improved SBR process is Attached Growth Batch Reactor (AGBR) technology that provisions for microbial growth on the settled media/bed to treat the industrial wastewater using enzymes. This technology, when used to treat polluted river water, achieved about 90% of reduction of wastewater parameters. Hence the same is envisioned for the treatment of industrial effluent. In all the above methods the sludge settlement occurs. It contains biodegradable carbon content which could be used as feed for Biogas Digesters to produce Methane. The present study aims at examining the benefits of combining AGBR and Biogas Digester to implement the 3Rs (Reduce, Recycle, Reuse) [1]


2020 ◽  
Vol 6 (1) ◽  
pp. 12-19
Author(s):  
Mohd Najib Razali ◽  
Amira Ermafiqka Anuar ◽  
Musfafikri Musa ◽  
Najmuddin Mohd Ramli

The industrial effluents from the oil and gas industry contain harmful contaminants that bring detrimental effects to the aquatic life and human population. The primary concerns are the high value of Chemical Oxygen Demand (COD), Total Suspended Solids (TSS), turbidity and heavy metal content such as ferum and copper in the effluents, which did not comply with the Environmental Quality Act (1974) Industrial Effluent (Regulations) 2009 of Malaysian Department of Environment (DOE). This research aims to study the efficiency of natural bio-coagulants in treating the industrial effluent from the oil and gas industry. The industrial effluent sample was treated by using two natural biocoagulants F.A and F.B and three commercial treatment agents (bio-solvent, alum, and poly aluminium chloride (PAC)). Different beakers consisting of 7.5 wt% of each agent were added into 1.5 L of wastewater sample and left for a week without mechanical assistance. For the second stage, only F.A and alum were used during the experiment. By using five different weight percentages: 2.5%, 5.0%, 7.5%, 10.0%, and 12.5%, the treatment agents were added into 100 ml of wastewater and left for a week without any mechanical assistance. Then, the samples were analyzed for each of the five parameters. The results showed F.A is the best agent in COD treatment, with 41% reduction; followed by alum with 36%, PAC with 26% and bio-solvent with 22% reduction, respectively. The obtained results also showed that F.A and alum are at optimum performances at 7.5 wt%. The F.A and alum efficiency are deteriorating when the dosage is below and above 7.5 wt%.


2021 ◽  
Vol 3 (30) ◽  
pp. 96-110
Author(s):  
Adel A. M. Saeed ◽  
◽  
Nasser M. N. Masood ◽  
Ali N. A. Al-Kumi ◽  
◽  
...  

Water pollution caused by leather industrial effluent discharges has become a troublesome phenomenon due to its negative impact on environmental health and safety. In this paper, the wastewater in the vicinity of Lawdar tannery areas was assessed in two years from October 2019 to June 2021 to determine physico-chemical parameters of industrial effluents of Lawdar tannery at four different area points. Tannery effluents were collected and all samples were analyzed in the laboratory and rated as no freshwater with parameters such as acidity and basicity, temperature, electrical conductivity, total dissolved solids, total suspended solids, chemical oxygen demand, biological oxygen demand, color, turbidity, hardness, alkalinity, and several positive and negative ions. The investigation showed that all physico-chemical parameters were higher than the standard disposal limits of discharged water quality. The findings of this research will assist the government and tanneries in the treatment of wastewater before discharging to the environment and monitoring the dump sites with regards to disposal arrangement of the tannery effluents and environmental assessment.


2020 ◽  
Vol 82 (11) ◽  
pp. 2259-2270
Author(s):  
Shaik Nazia ◽  
Sugali Chandra Sekhar ◽  
Veeriah Jegatheesan ◽  
Suresh K. Bhargava ◽  
Sundergopal Sridhar

Abstract The goal of the present study is to treat industrial wastewater containing sodium aluminate using a chemically inert polyurea (PU) based thin film composite (TFC) reverse osmosis (RO) membrane to promote water reclamation and zero liquid discharge (ZLD). Pretreatment was carried out to reduce the pH of the effluent from 12.5 to 7.1. The TFC RO membrane was fabricated by coating PU on Polyethersulfone (PES) substrate by interfacial polymerization (IP). The surface and cross-sectional morphologies of the membrane were characterized using scanning electron microscopy (SEM). The indigenously synthesized membrane was effective in the removal of total dissolved solids (TDS), chemical oxygen demand (COD), colour and electrical conductivity. The experiments were conducted by varying the feed composition of the wastewater. The maximum water recovery and flux were found to be 74% and 73.9 L/m2·h. RO process using PU membrane exhibited significant potential for cost effective, safe and pollution-free treatment of sodium aluminate industrial effluent.


2016 ◽  
Vol 74 (9) ◽  
pp. 2192-2201 ◽  
Author(s):  
Amna Ijaz ◽  
Zafar Iqbal ◽  
Muhammad Afzal

This investigation reports the quantitative assessment of endophyte-assisted floating treatment wetlands (FTWs) for the remediation of sewage and industrial wastewater. Typha domingensis was used to vegetate FTWs that were subsequently inoculated with a consortium of pollutant-degrading and plant growth-promoting endophytic bacteria. T. domingensis, being an aquatic species, holds excellent potential to remediate polluted water. Nonetheless, investigation conducted on Madhuana drain carrying industrial and sewage water from Faisalabad City revealed the percentage reduction in chemical oxygen demand (COD) and biochemical oxygen demand (BOD5) to be 87% and 87.5%, respectively, within 96 h on coupling the plant species with a consortium of bacterial endophytes. With the endophytes surviving in plant tissue, maximal reduction was obtained in not only the aforementioned pollution parameters but for other major environmental quality parameters including nutrients (N and P), ions (Na+ and K+), Cl−, and SO42− as well, which showed percentage reductions up to 90%, 39%, 77%, 91.8%, 40%, and 60%, respectively. This significant improvement in polluted wastewater quality treated with the proposed method render it safe to be discharged freely in larger water bodies as per the National Environmental Quality Standards (NEQS) of Pakistan or to be reused safely for irrigation purposes; thus, FTWs provide a sustainable and affordable approach for in situ remediation of sewage and industrial wastewater.


1991 ◽  
Vol 23 (7-9) ◽  
pp. 1293-1300 ◽  
Author(s):  
J. P. Maree ◽  
G. Hulse ◽  
D. Dods ◽  
C. E. Schutte

Sulphate-rich industrial effluents present a serious environmental pollution problem. A biological sulphate removal process has been developed for the treatment of such effluents. In this process, sulphate is converted to hydrogen sulphide in the anaerobic stage when an energy source, such as molasses, sugar or producer gas is added. The hydrogen sulphide is stripped off in a stripping stage, with a carrier gas such as nitrogen. The gas is recycled through a ferric solution where it is oxidized to elemental sulphur. In a subsequent aerobic stage, degradation of organic carbon residuals and calcium carbonate crystallization are achieved simultaneously. In this study the anaerobic stage of the process was evaluated on pilot scale. After the inoculation period, sulphate was removed continuously for a period of 100 days from 2200 mg/l to below 200 mg/l. For the first part of the study acetic acid served as energy source as the sugar content of molasses was allowed to ferment. Thereafter fresh molasses was supplied as energy source and the bacterial culture had to adapt to utilize sugar in molasses as energy source. A volatile suspended solids (VSS) concentration of 27 g/l was present in the packing material of the anaerobic reactor. With this VSS-value, a hydraulic retention time of 12 hours was needed for sulphate removal.


2016 ◽  
Vol 8 (1) ◽  
pp. 58-65
Author(s):  
Sadhana Pradhanang

The assessment of water quality of Karra River in Hetauda, Nepal was carried out by determining the changes in the concentration levels of eight physico-chemical parameters (pH, Electric conductivity (EC), bicarbonate, dissolved oxygen (DO), silica, chemical oxygen demand (COD), phosphate and nitrate). The samples were collected from upstream, industrial belt and downstream of the Karra River. The Karra River is the dumping ground for industrial effluents of Hetauda industrial district (HID). On analysis, the concentrations of most of the physico-chemicals parameters were found to be above the prescribed limits for industrial wastewater into inland surface waters. Dissolved Oxygen was found to be in the range of 0.49- 8.47 mg/L while COD, nitrate and phosphate were recorded in the range of 8.3-367 mg/L, 0.35- 78.22 mg/L and 0.01-1.64 mg/L, respectively. Concentrations of most of these parameters were within the prescribed limits in the samples collected from upstream and downstream, revealing the river still in good condition at these points indicating less human interference at the head water region and good self-purification capacity at downstream. However the concentrations of the pollutants’ parameters are higher at the sample points just after effluent discharge.Journal of Hydrology and Meteorology, Vol. 8(1) p.58-65


Water ◽  
2020 ◽  
Vol 12 (6) ◽  
pp. 1747 ◽  
Author(s):  
Rahmat Ngteni ◽  
Md. Sohrab Hossain ◽  
Mohd Omar Ab Kadir ◽  
Ahmad Jaril Asis ◽  
Zulhafiz Tajudin

There is increasing concern to determine an alternative coagulant for treating industrial effluent with minimal environmental impact and operational cost. In this study, iron (II) sulphate heptahydrate (FeSO4·7H2O) waste, an industrial byproduct from a titanium oxide processing industry, was used as a coagulant for the removal of ammonia (NH3), chemical oxygen demand (COD), biochemical oxygen demand (BOD), and suspended solid (SS) from secondary rubber processing effluent (SRPE). The highest percentage removal of BOD, COD, SS, and NH3 achieved was approximately 97%, 99%, 98%, and 95%, respectively, at pH 5.0, coagulant dose of 1 g/L, coagulation time of 60 min, sedimentation time of 60 min, and at an elevated temperature of 70 °C. The best described adsorption isotherm model was found to be the Brunauer–Emmett–Teller (BET) model, indicated that the FeSO4·7H2O adsorption took placed on the surface of iron hydroxide precipitates with multilayer formation and random distribution. The kinetics analysis showed that the adsorption mechanism was well fitted with the pseudo-second-order kinetic model. The findings of the present study show that the FeSO4·7H2O waste has the potential to be used as a coagulant for the treatment of industrial effluents, including the secondary rubber processing effluent.


2019 ◽  
Vol 8 (4) ◽  
pp. 12572-12580

This Tannery industry is one of oldest industry the effluent is highly complex and characterized by high Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), suspended solids, dissolved solids, total solids, and color. Untreated Tannery wastewater when discharged directly into the water bodies or into open lands cause irreversible damage to environment. Electrocoagulation is one of the most important electrochemical treatment employed for industrial wastewater treatment to treat highly polluted industrial effluents which have high suspended and colloidal materials, BOD, COD in wastewater. Electrocoagulation treatment is used in this study to study the removal efficiency of BOD, COD, Chromium (Cr) Total Dissolved Solids (TDS) and the effect of pH of tannery wastewater. The experiments were conducted using aluminum and iron as plane and punched electrodes. When aluminum Plane and punched electrodes were used the optimum removal efficiency for plain electrodes was found to be BOD-89.66%, COD-96.21%, Cr-96.05% and TDS-95.77% for punched electrodes BOD-90.86%, COD-98.62%, Cr-96.94% and TDS96.92% and for iron plane electrodes BOD-87.57%, COD94.77%, Cr-93.42% and TDS-93.08% for iron punched electrodes BOD-89.01%, 96.59%, Cr-94.66% and TDS-95.0% at pH of 9, Voltage 20V, for electrode distance of 1cm and 90 minutes electrolysis duration. The Electrocoagulation treatment has proved to be economical and efficient method for the treatment of tannery wastewater rather than chemical coagulation.


2020 ◽  
Vol 4 (1) ◽  
pp. 16 ◽  
Author(s):  
Shanta Biswas ◽  
Taslim Ur Rashid ◽  
Tonmoy Debnath ◽  
Papia Haque ◽  
Mohammed Mizanur Rahman

In recent years, there has been increasing interest in developing green biocomposite for industrial wastewater treatment. In this study, prawn-shell-derived chitosan (CHT) and kaolinite rich modified clay (MC) were used to fabricate biocomposite beads with different compositions. Prepared composite beads were characterized by FTIR, and XRD, and SEM. The possible application of the beads was evaluated primarily by measuring the adsorption efficiency in standard models of lead (II) and methylene blue (MB) dye solution, and the results show a promising removal efficiency. In addition, the composites were used to remove Cr (VI), Pb (II), and MB from real industrial effluents. From tannery effluent, 50.90% of chromium and 39.50% of lead ions were removed by composites rich in chitosan and 31.50% of MB was removed from textile effluent by a composite rich in clay. Moreover, the composite beads were found to be activated in both acidic and basic media depending on their composition, which gives a scope to their universal application in dye and heavy metal removal from wastewater from various industries.


Sign in / Sign up

Export Citation Format

Share Document