scholarly journals Effect of cations on the removal rate of chloride ions and mechanism analysis in high-salt wastewater

2021 ◽  
Author(s):  
Kangning Gao ◽  
Jie Lu ◽  
Xi Wang ◽  
Dengxin Li ◽  
Shihong Xu
Keyword(s):  
Removal Rate ◽  
Low Cost ◽  
Chloride Ion ◽  
Chloride Ions ◽  
High Salt ◽  
Cuprous Chloride ◽  
Mechanism Analysis ◽  
Chlorine Gas ◽  
Chlorine Ions ◽  
Chlorine Removal

Abstract Precipitation dechlorination has the advantage of being a simple process with a low cost. However, there are few reports on the effect of cations on dechlorination. In this study, we investigated the effect of cations in high-salt wastewater on the removal of chlorine ions by cuprous chloride precipitation and analysed the corresponding mechanism. A series of investigations revealed that Fe3+ could oxidise sulphite, thereby reducing the removal rate of chlorine ions. The reaction between magnesium and sulphite results in precipitation, which has a slightly adverse effect on the removal of chloride ions. Hexavalent chromium oxidises the chloride ion, resulting in the formation of chlorine gas, which improves the removal rate. Ferrous and manganese, however, do not have a notable effect on chlorine removal.

scholarly journals Layered Double Hydroxides Precursor as Chloride Inhibitor: Synthesis, Characterization, Assessment of Chloride Adsorption Performance

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2537 ◽  
Author(s):  
Lin Chi ◽  
Zheng Wang ◽  
Youfang Zhou ◽  
Shuang Lu ◽  
Yan Yao
Keyword(s):  
Removal Rate ◽  
Chloride Ion ◽  
Cementitious Materials ◽  
Chloride Ions ◽  
Ion Removal ◽  
Hydraulic Concrete ◽  
Adsorption Behaviors ◽  
The Stability ◽  
Inhibition Performance ◽  
Double Hydroxides

In this study, the chloride adsorption behaviors of CaAl-Cl LDH precursors with various Ca:Al ratios were investigated. The optimal chloride ion removal rate was 87.06% due to the formation of hydrocalumite. The chloride adsorption products of CaAl-Cl LDH precursors were further characterized by X-ray diffraction analysis and atomic structure analysis, the adsorption mechanism was considered to be co-precipitate process. The chloride adsorption behaviors of cementitious materials blended with CaAl-Cl LDH precursors were further investigated. Leaching test according to Test Code for Hydraulic Concrete (SL352-2006) was performed to testify the stability of chloride ions in the mortar. The results show that more than 98.3% chloride ions were immobilized in cement mortar blended with CaAl-Cl LDH precursor and cannot be easily released again. The inhibition performance of steel in the electrolytes with/without CaAl LDH precursor was investigated by using electrochemical measurements. The results indicate that CaAl LDH precursor can effectively protect the passive film on steel surface by chloride adsorption. Considering the high anion exchange capacities of the LDHs, synthesized chloride adsorbent precursor can be applied as new inhibitors blended in cementitious materials to prevent the chloride-induced deterioration. Moreover, the application of chloride adsorption on CaAl-Cl LDH could also be of interest for the application of seawater blended concrete.

Deterioration of Laterite Engineering by Chloride Ion

2012 ◽  
Vol 204-208 ◽  
pp. 389-392 ◽  
Author(s):  
Gang Chen ◽  
Hua Shu Yang ◽  
Jin Yu Li ◽  
Yi Zhi Yan ◽  
Luo Shao
Keyword(s):  
Grain Size ◽  
Chloride Ion ◽  
Chloride Ions ◽  
Mechanism Analysis ◽  
Permeability Test ◽  
Iron Ion ◽  
Accelerated Life Tests ◽  
Accelerated Life ◽  
Life Tests ◽  
Concentration Changes

Water of reservoirs shows acidity in laterite regions, and laterite engineering is chronically demolished by chloride ions in water. Ground on mechanism analysis, accelerated life tests were implemented. After permeability test, changes of grain-size-gradation were analysed at laterite remainder, microstructures of soil sample were observed, and concentration changes of iron ion as well as aluminum ion were affirmed in transudatory liquid. The harvests indicated that: sesquioxides (viscous substances in laterite) are consumed by chloride ions in water, and microstructures of laterite are demolished. Products from chemical reaction are dissolved by water and are schlepped off by seepage, so wispy leakage channels are created in engineering. The eroding of chloride ions has clearly debased security of laterite engineering.

scholarly journals The Effect of a Corrosion Inhibitor on the Rehabilitation of Reinforced Concrete Containing Sea Sand and Seawater

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1480 ◽  
Author(s):  
Chonggen Pan ◽  
Xu Li ◽  
Jianghong Mao
Keyword(s):  
Reinforced Concrete ◽  
Corrosion Inhibitor ◽  
Control Experiment ◽  
Chloride Ion ◽  
Chloride Ions ◽  
Maximum Value ◽  
Steel Bar ◽  
Sea Sand ◽  
Chlorine Ions ◽  
Electrochemical Chloride Extraction

Concrete made with sea sand and seawater is rich in chlorine ions which are the main factors that induce corrosion of the reinforcement. In this study, an innovative method to rehabilitate reinforcement is presented; the concentrations of chloride ions and the corrosion inhibitor in concrete were measured. Electrochemical chloride extraction (ECE) was applied as a control experiment via using saturated Ca(OH)2 solution as an external electrolyte. Bidirectional electromigration (BIEM)technology combined with the corrosion inhibitor could not only remove the chloride ions but also protect the steel bar in concrete, and animidazoline inhibitor mixed in concrete is more effective than thetriethylenetetramine inhibitor due to the specific molecular structure. It was found that the optimum ratio of N/Cl reached the maximum value 3.3, when the concentration of inhibitor was 1. Meanwhile, the experimental results also revealed that the corrosion inhibitor and chloride ion concentrations reached necessary levels on the surface of the steel, and the corrosion inhibitor migrated effectively. Overall, the contents of imidazoline and triethylenetetramine inhibitor in seawater concrete are0.75% and 1%, respectively. The results demonstrate that the addition of the corrosion inhibitor and the application of bidirectional electromigration would effectively improve the durability of reinforced concrete containing sea sand and seawater.

scholarly journals Mechanism analysis and model calculation of chloride ion diffusion in reinforced concrete structure

2020 ◽  
Vol 198 ◽  
pp. 01035
Author(s):  
Faqiang Yu ◽  
Weiwei Gao ◽  
Wenchao Liu
Keyword(s):  
Reinforced Concrete ◽  
Diffusion Mechanism ◽  
Concrete Structures ◽  
Chloride Concentration ◽  
Chloride Ion ◽  
Chloride Ions ◽  
Cumulative Distribution ◽  
Reinforced Concrete Structures ◽  
Mechanism Analysis ◽  
Reinforced Concrete Structure

Chloride-induced corrosion of steel in reinforced concrete structures is one of the major causes of their deterioration over time. The analysis and research on the diffusion mechanism of chloride ions in reinforced concrete structures is still insufficient, and it is necessary to calculate the path of chloride ions based on theoretical models. In this paper, the fick’s second law was used to describe the free chloride concentration evolution in concrete. The Monte Carlo simulation was used to predict the cumulative distribution of corrosion initiation of reinforcing steel.The results show that the calculated results of the established model are in good agreement with the measured results.

scholarly journals Experimental Study and Simulation Calculation of the Chloride Resistance of Concrete under Multiple Factors

2021 ◽  
Vol 11 (12) ◽  
pp. 5322
Author(s):  
Yang Ding ◽  
Tong-Lin Yang ◽  
Hui Liu ◽  
Zhen Han ◽  
Shuang-Xi Zhou ◽  
...  
Keyword(s):  
Hydrostatic Pressure ◽  
Penetration Depth ◽  
Chloride Ion ◽  
Cementitious Materials ◽  
Chloride Ions ◽  
Finite Element Software ◽  
Chloride Resistance ◽  
Simulation Calculation ◽  
Marine Concrete ◽  
Resistance Performance

Cement is widely used in marine concrete, and its resistance to chloride ion corrosion has been widely considered. In this paper, based on a laboratory test, the influence of different hydrostatic pressures, coarse aggregate contents and w/c ratios on the chloride resistance performance is analyzed. Based on COMSOL finite element software, a two-dimensional cementitious materials model is established, and the simulation results are compared with the experimental results. The results show that the penetration depth of chloride ions in cement increases with the increase of the w/c ratio. Under the hydrostatic pressure of 0 MPa, when the w/c ratio is 0.35, the penetration depth of chloride ions is 7.4 mm, and the simulation result is 8.0 mm. When the w/c ratio is 0.45, the penetration depth of chloride ions is 9.3 mm, and the simulation result is 9.9 mm. When the w/c ratio is 0.55, the penetration depth of chloride ions is 12.9 mm, and the simulation result is 12.1 mm. Under different hydrostatic pressures, the penetration depth of chloride ions obviously changes, and with the increase in hydrostatic pressure, the penetration depth of chloride ions deepens. Under the w/c ratio of 0.35, when the hydrostatic pressure is 0.5 MPa, the penetration depth of chloride ions is 11.3 mm, and the simulation result is 12.1 mm. When the hydrostatic pressure is 1.0 MPa, the penetration depth of chloride ions is 16.2 mm, and the simulation result is 17.5 mm.

scholarly journals Broadband dielectric spectroscopy for monitoring temperature-dependent chloride ion motion in BiOCl plates

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Adrian Radoń ◽  
Dariusz Łukowiec ◽  
Patryk Włodarczyk
Keyword(s):  
Electrical Conductivity ◽  
Dielectric Spectroscopy ◽  
Low Frequency ◽  
Chloride Ion ◽  
Ion Source ◽  
Chloride Ions ◽  
Ion Concentration ◽  
Broadband Dielectric Spectroscopy ◽  
Free Chloride ◽  
Structure Rebuilding

AbstractThe dielectric properties and electrical conduction mechanism of bismuth oxychloride (BiOCl) plates synthesized using chloramine-T as the chloride ion source were investigated. Thermally-activated structure rebuilding was monitored using broadband dielectric spectroscopy, which showed that the onset temperature of this process was 283 K. This rebuilding was related to the introduction of free chloride ions into [Bi2O2]2+ layers and their growth, which increased the intensity of the (101) diffraction peak. The electrical conductivity and dielectric permittivity were related to the movement of chloride ions between plates (in the low-frequency region), the interplanar motion of Cl− ions at higher frequencies, vibrations of these ions, and charge carrier hopping at frequencies above 10 kHz. The influence of the free chloride ion concentration on the electrical conductivity was also described. Structure rebuilding was associated with a lower concentration of free chloride ions, which significantly decreased the conductivity. According to the analysis, the BiOCl plate conductivity was related to the movement of Cl− ions, not electrons.

scholarly journals Preparation and Characterization of High-Efficiency Magnetic Heavy Metal Capture Flocculants

Water ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 1732
Author(s):  
Yuanyuan Yu ◽  
Yongjun Sun ◽  
Jun Zhou ◽  
Aowen Chen ◽  
Kinjal J. Shah
Keyword(s):  
Heavy Metal ◽  
Reaction Time ◽  
High Efficiency ◽  
Removal Rate ◽  
Low Cost ◽  
Monomer Concentration ◽  
Synthesis Process ◽  
Response Surface Optimization ◽  
Metal Capture ◽  
Total Monomer Concentration

In this study, a high-efficiency magnetic heavy metal flocculant MF@AA was prepared based on carboxymethyl chitosan and magnetic Fe3O4. It was characterized by SEM, FTIR, XPS, XRD and VSM, and the Cu(II) removal rate was used as the evaluation basis for the preparation process. The effects of AMPS content, total monomer concentration, photoinitiator concentration and reaction time on the performance of MF@AA flocculation to remove Cu(II) were studied. The characterization results show that MF@AA has been successfully prepared and exhibits good magnetic induction characteristics. The synthesis results show that under the conditions of 10% AMPS content, 35% total monomer concentration, 0.04% photoinitiator concentration, and 1.5 h reaction time, the best yield of MF@AA is 77.69%. The best removal rate is 87.65%. In addition, the response surface optimization of the synthesis process of MF@AA was performed. The optimal synthesis ratio was finally determined as iron content 6.5%, CMFS: 29.5%, AM: 53.9%, AMPS: 10.1%. High-efficiency magnetic heavy metal flocculant MF@AA shows excellent flocculation performance in removing Cu(II). This research provides guidance and ideas for the development of efficient and low-cost flocculation technology to remove Cu(II) in wastewater.

scholarly journals Adsorption of copper ions on Magnolia officinalis residues after solid-phase fermentation with Phanerochaete chrysosporium

2019 ◽  
Vol 17 (1) ◽  
pp. 1173-1184 ◽  
Author(s):  
Fengyun Tao ◽  
Yangping Liu ◽  
Junliang Chen ◽  
Peng Wang ◽  
Qing Huo
Keyword(s):  
Chinese Medicine ◽  
Phanerochaete Chrysosporium ◽  
Solid Phase ◽  
Copper Ions ◽  
Removal Rate ◽  
Low Cost ◽  
Preparation Technique ◽  
Adsorption Enthalpy ◽  
Pseudo Second Order ◽  
Magnolia Officinalis

AbstractThe disposal of residues while manufacturing Chinese medicine has always been an issue that concerns pharmaceutical factories. Phanerochaete chrysosporium was inoculated into the residues of Magnolia officinalis for solid-phase fermentation to enzymatically hydrolyze the lignin in the residues and thus to improve the efficiency of removal of the copper ions from residues for the utilization of residues from Chinese medicine. With the increase in activities of lignin-degrading enzymes, especially during the fermentation days 6 to 9, the removal rate of copper ions using M. officinalis residues increased dramatically. The rate of removal reached the maximum on the 14th day and was 3.15 times higher than the initial value. The rate of adsorption of copper ions on the fermentation-modified M. officinalis residues followed the pseudo-second-order kinetics. The adsorption isotherms were consistent with the Freundlich models. The adsorption enthalpy was positive, indicating that it was endothermic and elevation in temperature was favorable to this adsorption process. The adsorption free energy was negative, implying the spontaneity of the process. The copper ions adsorbed could be effectively recovered using 0.2 M hydrochloric acid solution. After five successive cycles of adsorption-regeneration, the fermentation-modified M. officinalis residues exhibited a stable adsorption capacity and greater reusability. The M. officinalis residues fermented with P. chrysosporium are low-cost and environmentally friendly copper ions adsorbent, and this preparation technique realizes the optimum utilization of Chinese medicine residues.

Integrated Process for Textile Cotton Waste (TCW) Valorization: Waste-to-Energy and Wastewater Decontamination

2016 ◽  
Author(s):  
A. Ribeiro ◽  
C. Vilarinho ◽  
J. Araújo ◽  
J. Carvalho
Keyword(s):  
Raw Materials ◽  
Removal Rate ◽  
Low Cost ◽  
Calorific Value ◽  
Waste To Energy ◽  
Synthetic Wastewater ◽  
Small Scale ◽  
World Population ◽  
Cotton Waste ◽  
Textile Industries

The increasing of world population, industrialization and global consuming, existing market products existed in the along with diversification of raw materials, are responsible for an exponential increase of wastes. This scenario represents loss of resources and ultimately causes air, soils and water pollution. Therefore, proper waste management is currently one of the major challenges faced by modern societies. Textile industries represents, in Portugal, almost 10% of total productive transforming sector and 19% of total employments in the sector composed by almost 7.000 companies. One of the main environmental problems of textile industries is the production of significant quantities of wastes from its different processing steps. According to the Portuguese Institute of Statistics (INE) these industries produce almost 500.000 tons of wastes each year, with the textile cotton waste (TCW) being the most expressive. It was estimated that 4.000 tons of TCW are produced each year in Portugal. In this work an integrated TCW valorisation procedure was evaluated, firstly by its thermal and energetic valorisation with slow pyrolysis followed by the utilization of biochar by-product, in lead and chromium synthetic wastewater decontamination. Pyrolysis experiments were conducted in a small scale rotating pyrolysis reactor with 0.1 m3 of total capacity. Results of pyrolysis experiments showed the formation of 0,241 m3 of biogas for each kilogram of TCW. Results also demonstrated that the biogas is mostly composed by hydrogen (22%), methane (14 %), carbon monoxide (20%) and carbon dioxide (12%), which represents a total high calorific value of 12.3 MJ/Nm3. Regarding biochar, results of elemental analysis demonstrated a high percentage of carbon driving its use as low cost adsorbent. Adsorption experiments were conducted with lead and chromium synthetic wastewaters (25, 50 and 100 mg L−1) in batch vessels with controlled pH. It was evaluated the behaviour of adsorption capacity and removal rate of each metal during 120 minutes of contact time using 5, 10 and 50 g L−1 of adsorbent dosage. Results indicated high affinity of adsorbent with each tested metal with 78% of removal rate in chromium and 95% in lead experiments. This suggests that biochar from TCW pyrolysis may be appropriated to wastewaters treatment, with high contents of heavy metals and it can be an effective alternative to activated carbon.

GABA responses in rat dentate granule neurons are mediated by chloride

1988 ◽  
Vol 66 (5) ◽  
pp. 637-642 ◽  
Author(s):  
Timothy J. Blaxter ◽  
Peter L. Carlen
Keyword(s):  
Granule Cells ◽  
Hippocampal Slices ◽  
Reversal Potential ◽  
Chloride Ion ◽  
Chloride Ions ◽  
Ion Concentration ◽  
Aminobutyric Acid ◽  
Granule Neurons ◽  
Nernst Equation ◽  
Central Neurons

The dendrites of granule cells in hippocampal slices responded to γ-aminobutyric acid (GABA) with a depolarization. The response was blocked by picrotoxin in a noncompetitive manner. Reductions in the extracellular chloride ion concentration changed the reversal potential of the response by an amount predicted from the Nernst equation for chloride ion. Chloride-dependent hyperpolarizing responses were sometimes also found in the cell body of the granule cells. Since the reversal potential followed that predicted from the Nernst equation for chloride, we conclude that the response was mediated by chloride ions alone with no contribution from other ions. This has not previously been shown for the depolarizing response to GABA in central neurons.

Sign in / Sign up

Export Citation Format

Share Document