Precise Localization of 28 nm via Chain Resistive Defect Using EBAC and Nanoprobing

2012 ◽  
Author(s):  
P. Larré ◽  
H. Tupin ◽  
C. Charles ◽  
R.H. Newton ◽  
A. Reverdy
Keyword(s):  
Electron Beam ◽  
Failure Analysis ◽  
Test Structure ◽  
Precise Localization ◽  
Isolation Method ◽  
Accurate Detection ◽  
Conventional Methods ◽  
Technology Nodes ◽  
Tem Lamella

Abstract As technology nodes continue to shrink, resistive opens have become increasingly difficult to detect using conventional methods such as AVC and PVC. The failure isolation method, Electron Beam Absorbed Current (EBAC) Imaging has recently become the preferred method in failure analysis labs for fast and highly accurate detection of resistive opens and shorts on a number of structures. This paper presents a case study using a two nanoprobe EBAC technique on a 28nm node test structure. This technique pinpointed the fail and allowed direct TEM lamella.

Enhanced Failure Analysis on Open TSV Interconnects

2012 ◽  
Author(s):  
F. Altmann ◽  
C. Schmidt ◽  
J. Beyersdorfer ◽  
M. Simon-Najasek ◽  
C. Große ◽  
...  
Keyword(s):  
Electron Beam ◽  
High Resolution ◽  
Failure Analysis ◽  
Preparation Technique ◽  
Target Preparation ◽  
Material Analysis ◽  
Highly Efficient ◽  
Lock In

Abstract In this paper different methods and novel tools for failure localisation and high resolution material analysis for open TSV interconnects will be discussed. The paper shows the application of enhanced methods for the localisation of sidewall shorts in open TSV structures by adapted Photoemission Microscopy (PEM), Lock-in Thermography (LIT) and Electron Beam Absorbed Imaging (EBAC). In addition, a new highly efficient target preparation technique is presented, which allows the combination of Laser and FIB milling, in order to access TSV sidewall defects. Finally the use of this technique is demonstrated in a failure analysis case study.

Failure Analysis Case Study of a 1.5 Meter Space Flex Harness

2017 ◽  
Author(s):  
Erick Kim ◽  
Kamjou Mansour ◽  
Gil Garteiz ◽  
Javeck Verdugo ◽  
Ryan Ross ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Failure Modes ◽  
Field Of View ◽  
Area Of Interest ◽  
Air Stream ◽  
Novel Method ◽  
Temperature Controlled ◽  
Non Destructive ◽  
Failure Site

Abstract This paper presents the failure analysis on a 1.5m flex harness for a space flight instrument that exhibited two failure modes: global isolation resistances between all adjacent traces measured tens of milliohm and lower resistance on the order of 1 kiloohm was observed on several pins. It shows a novel method using a temperature controlled air stream while monitoring isolation resistance to identify a general area of interest of a low isolation resistance failure. The paper explains how isolation resistance measurements were taken and details the steps taken in both destructive and non-destructive analyses. In theory, infrared hotspot could have been completed along the length of the flex harness to locate the failure site. However, with a field of view of approximately 5 x 5 cm, this technique would have been time prohibitive.

Failure Analysis of CDM-ESD Damage in a GaAs RFIC

2000 ◽  
Author(s):  
Amy Poe ◽  
Steve Brockett ◽  
Tony Rubalcava
Keyword(s):  
Radio Frequency ◽  
Failure Analysis ◽  
Integrated Circuit ◽  
Production Test ◽  
Analysis Techniques ◽  
Device Model ◽  
Charged Device ◽  
Subsequent Failure

Abstract The intent of this work is to demonstrate the importance of charged device model (CDM) ESD testing and characterization by presenting a case study of a situation in which CDM testing proved invaluable in establishing the reliability of a GaAs radio frequency integrated circuit (RFIC). The problem originated when a sample of passing devices was retested to the final production test. Nine of the 200 sampled devices failed the retest, thus placing the reliability of all of the devices in question. The subsequent failure analysis indicated that the devices failed due to a short on one of two capacitors, bringing into question the reliability of the dielectric. Previous ESD characterization of the part had shown that a certain resistor was likely to fail at thresholds well below the level at which any capacitors were damaged. This paper will discuss the failure analysis techniques which were used and the testing performed to verify the failures were actually due to ESD, and not caused by weak capacitors.

Advanced IR-OBIRCH Analysis Technique for High Isb Failure Analysis

2010 ◽  
Author(s):  
Kuo Hsiung Chen ◽  
Wen Sheng Wu ◽  
Yu Hsiang Shu ◽  
Jian Chan Lin
Keyword(s):  
Failure Analysis ◽  
Failure Mechanisms ◽  
Fault Localization ◽  
Resistance Change ◽  
The Real ◽  
Analysis Techniques ◽  
Analysis Technique ◽  
Leakage Failure ◽  
Failure Site

Abstract IR-OBIRCH (Infrared Ray – Optical Beam Induced Resistance Change) is one of the main failure analysis techniques [1] [2] [3] [4]. It is a useful tool to do fault localization on leakage failure cases such as poor Via or contact connection, FEoL or BEoL pattern bridge, and etc. But the real failure sites associated with the above failure mechanisms are not always found at the OBIRCH spot locations. Sometimes the real failure site is far away from the OBIRCH spot and it will result in inconclusive PFA Analysis. Finding the real failure site is what matters the most for fault localization detection. In this paper, we will introduce one case using deep sub-micron process generation which suffers serious high Isb current at wafer donut region. In this case study a BEoL Via poor connection is found far away from the OBIRCH spots. This implies that layout tracing skill and relation investigation among OBIRCH spots are needed for successful failure analysis.

The Electrical Characterization and Physical Failure Analysis for Transistor Gate Leakage

2006 ◽  
Author(s):  
Tsung-Te Li ◽  
Chao-Chi Wu ◽  
Jung-Hsiang Chuang ◽  
Jon C. Lee
Keyword(s):  
Failure Analysis ◽  
Electrical Characterization ◽  
Physical Analysis ◽  
Gate Leakage ◽  
Force Microscopy ◽  
Atomic Force ◽  
Transmission Electron ◽  
Voltage Stress ◽  
Leakage Site

Abstract This article describes the electrical and physical analysis of gate leakage in nanometer transistors using conducting atomic force microscopy (C-AFM), nano-probing, transmission electron microscopy (TEM), and chemical decoration on simulated overstressed devices. A failure analysis case study involving a soft single bit failure is detailed. Following the nano-probing analysis, TEM cross sectioning of this failing device was performed. A voltage bias was applied to exaggerate the gate leakage site. Following this deliberate voltage overstress, a solution of boiling 10%wt KOH was used to etch decorate the gate leakage site followed by SEM inspection. Different transistor leakage behaviors can be identified with nano-probing measurements and then compared with simulation data for increased confidence in the failure analysis result. Nano-probing can be used to apply voltage stress on a transistor or a leakage path to worsen the weak point and then observe the leakage site easier.

SEM-Based Nanoprobing on 40, 32 and 28 nm CMOS Devices Challenges for Semiconductor Failure Analysis

2013 ◽  
Author(s):  
Erik Paul ◽  
Holger Herzog ◽  
Sören Jansen ◽  
Christian Hobert ◽  
Eckhard Langer
Keyword(s):  
Electron Microscope ◽  
High Resolution ◽  
Scanning Electron Microscope ◽  
Failure Analysis ◽  
Case Studies ◽  
State Of The Art ◽  
Root Cause ◽  
Highly Efficient ◽  
Technology Nodes ◽  
Scanning Electron

Abstract This paper presents an effective device-level failure analysis (FA) method which uses a high-resolution low-kV Scanning Electron Microscope (SEM) in combination with an integrated state-of-the-art nanomanipulator to locate and characterize single defects in failing CMOS devices. The presented case studies utilize several FA-techniques in combination with SEM-based nanoprobing for nanometer node technologies and demonstrate how these methods are used to investigate the root cause of IC device failures. The methodology represents a highly-efficient physical failure analysis flow for 28nm and larger technology nodes.

A Novel Junction Profiling Methodology

2010 ◽  
Author(s):  
Tomokazu Nakai
Keyword(s):  
Failure Analysis ◽  
Profile Analysis ◽  
Semiconductor Devices ◽  
Wet Etching ◽  
Two Dimensional ◽  
Electrical Characteristics ◽  
Conventional Methods

Abstract Currently many methods are available to obtain a junction profile of semiconductor devices, but the conventional methods have drawbacks, and they could be obstacles for junction profile analysis. This paper introduces an anodic wet etching-based two-dimensional junction profiling method, which is practical, efficient, and reliable for failure analysis and electrical characteristics evaluation.

Case Study in Fault Isolation of a Metal Short for Yield Enhancement

2010 ◽  
Author(s):  
Sarven Ipek ◽  
David Grosjean
Keyword(s):  
Failure Analysis ◽  
Failure Mechanism ◽  
Photon Emission ◽  
Fault Isolation ◽  
Yield Enhancement ◽  
Analysis Technique ◽  
Laser Signal ◽  
Signal Injection ◽  
Microscopy Techniques

Abstract The application of an individual failure analysis technique rarely provides the failure mechanism. More typically, the results of numerous techniques need to be combined and considered to locate and verify the correct failure mechanism. This paper describes a particular case in which different microscopy techniques (photon emission, laser signal injection, and current imaging) gave clues to the problem, which then needed to be combined with manual probing and a thorough understanding of the circuit to locate the defect. By combining probing of that circuit block with the mapping and emission results, the authors were able to understand the photon emission spots and the laser signal injection microscopy (LSIM) signatures to be effects of the defect. It also helped them narrow down the search for the defect so that LSIM on a small part of the circuit could lead to the actual defect.

Super-Conducting Quantum Interference Device Technique: 3-D Localization of a Short within a Flip Chip Assembly

2001 ◽  
Author(s):  
Kendall Scott Wills ◽  
Omar Diaz de Leon ◽  
Kartik Ramanujachar ◽  
Charles P. Todd
Keyword(s):  
Form Factor ◽  
Failure Analysis ◽  
Time Domain ◽  
Quantum Interference ◽  
Flip Chip ◽  
Time Domain Reflectometry ◽  
Interfacial Region ◽  
Precise Localization ◽  
Super Conducting ◽  
Accuracy Of Measurement

Abstract In the current generations of devices the die and its package are closely integrated to achieve desired performance and form factor. As a result, localization of continuity failures to either the die or the package is a challenging step in failure analysis of such devices. Time Domain Reflectometry [1] (TDR) is used to localize continuity failures. However the accuracy of measurement with TDR is inadequate for effective localization of the failsite. Additionally, this technique does not provide direct 3-Dimenstional information about the location of the defect. Super-conducting Quantum Interference Device (SQUID) Microscope is useful in localizing shorts in packages [2]. SQUID microscope can localize defects to within 5um in the X and Y directions and 35um in the Z direction. This accuracy is valuable in precise localization of the failsite within the die, package or the interfacial region in flipchip assemblies.

Die-Level Scanning Capacitance Microscopy Fault Isolation on SOI Fin-FET Devices for Advanced Semiconductor Nodes

2018 ◽  
Author(s):  
Lucile C. Teague Sheridan ◽  
Tanya Schaeffer ◽  
Yuting Wei ◽  
Satish Kodali ◽  
Chong Khiam Oh
Keyword(s):  
Atomic Force Microscopy ◽  
Failure Analysis ◽  
Fault Isolation ◽  
Scanning Capacitance Microscopy ◽  
Force Microscopy ◽  
Atomic Force

Abstract It is widely acknowledged that Atomic force microscopy (AFM) methods such as conductive probe AFM (CAFM) and Scanning Capacitance Microscopy (SCM) are valuable tools for semiconductor failure analysis. One of the main advantages of these techniques is the ability to provide localized, die-level fault isolation over an area of several microns much faster than conventional nanoprobing methods. SCM, has advantages over CAFM in that it is not limited to bulk technologies and can be utilized for fault isolation on SOI-based technologies. Herein, we present a case-study of SCM die-level fault isolation on SOI-based FinFET technology at the 14nm node.

Sign in / Sign up

Export Citation Format

Share Document