scholarly journals Applied implications for food marketing, quality assurance and control: an approach based on analyzing consumer attitudes and behavior

2014 ◽  
Vol 17 (3) ◽  
pp. 42-62
Author(s):  
Tuu Huy Ho ◽  
Hau Nguyen Le

Purposes – This paper presents the idea that food quality management and control should be based on marketing orientation perspectives. It aims to explore the cues, reasons, criteria and sources of perceived quality and food risks, then investigates their influences on consumer satisfaction and consumption toward food (fish) in Vietnam. Finally, it recommends some directions for future research in both food marketing and Quality Control. Methods – This presentation is based on a range of research studies using different data sets collected across provinces in Vietnam, and using different methods to analyze the data and test constructs, hypotheses and models. Findings – First, it indicates that nutrition and taste occupy the highest ratio explaining for positive attitudes (positive perceived quality), while safety and negative feelings are dominated to explain negative attitudes (food risks). Consumers with more positive (negative) reasons have a higher (lower) consumption. Second, perceived quality as a a multidimensional construct is found to have a positive effect on consumer satisfaction, while negative feelings have a negative effect on satisfaction. Perceived price has no a significant influence on satisfaction but a significant positive effect on perceived quality. The results also show that there are four groups of reasons causing food risks coming from producers, sellers, consumers and products. Perceived food risk is found to have an indirect effect on consumption via consumer satisfaction, and negatively moderate the satisfactionconsumption relationship. However, the effect of perceived risks is weaker when consumer knowledge increases. Finally, ambivalence is found to have a negative direct effect on both satisfaction and health involvement. Both ambivalence and health involvement are found to moderate the satisfaction–consumption relationship in a complex mechanism. Managerial implications – Managers and marketers should pay attention to reasons for consumer attitudes and consumption and have a multidimensional view of food quality and risk. Marketing strategies, which reduce consumer risks and educate them with relevant knowledge, may be effective strategies to increase consumption. For Quality Control, it is important that they must understand not only the established sensory standards for product quality, but also know, if possible, consumer expectations of sensory evaluations particularly at target markets pursed by a food company. Quality Control must understand all the traceable systems from raw material sourcing to finished products, and find and prevent all kind of tricks and methods that producers, processors and sellers use to avoid or even go around the specifications for the lack of the right raw material at the right time. It is important to recruit Quality Control Inspectors who can do all this right and have the basic knowledge. Limitation and future research – This paper focuses on only fish. Future research should expand to other foods and try to answer the following research questions: Do the certainty or stability of perceived quality affect and/or interact with consumer satisfaction to increase consumption/loyalty? Do perceived food quality and perceived price interact to influence consumer satisfaction and consumption? Do perceived food quality and perceived risk interact to influence consumer satisfaction and consumption? What form of risk interacts with what dimension of perceived quality to influence consumer satisfaction and consumption? How can each kind of consumer knowledge help to decrease the negative effects of food risks? How can Quality Control and quality programs be built to solve the problems of fishing vessels, farmers, processors, marketing sectors and the consumers, and to increase the consumer’s security in health and nutritional values.

2014 ◽  
Vol 9 (12) ◽  
pp. 1934578X1400901
Author(s):  
Paula Carolina Pires Bueno ◽  
Milton Groppo Junior ◽  
Jairo Kenupp Bastos

In this work we have validated a method to standardize and control the quality of Eucalyptus globulus raw material and phytomedicines containing either the essential oil or the fluid extract of this plant in the final formulation. Internal standardization provided a simple, fast, and reproducible GC-FID analytical method that accurately quantified 1,8-cineol in different E. globulus sub-products, such as its essential oil, dried leaves, fluid extract, and syrup. In addition, GC-MS identification of the main compounds of E. globulus species afforded fingerprints for the qualitative analysis of different Eucalyptus species.


2020 ◽  
Vol 3 (3) ◽  
pp. 1-5
Author(s):  
Yu.N. Gagarin ◽  

This article (the response to review) provides a commentary on the proposals of the reviewers on improving the economic system of forestry through an objective ecological and economic assessment of forests and the excess of prices for forest resources over the cost of their reproduction. It is noted that this proposal retains the right of the forest owner (state) to sell forest resources and, accordingly, consolidates the current budgetary model of forestry, based on budgeting and control of forestry costs. The article expresses the opinion about the erroneousness of judgments defining forestry in the system of economic relations as a raw material sector of the timber industry.


2021 ◽  
Vol 29 (4) ◽  
Author(s):  
Nadjim Mkedder ◽  
Mahmut Bakır ◽  
Abdelheq Lachachi

Purpose: The aim of this study was to investigate the antecedents of consumers’ purchase intention toward local dairy products. In doing so, this article delves into the relationships between perceived quality, perceived price, customer satisfaction, brand image, and customer purchase intention in the context of developing countries. Design/methodology/approach: Drawing on the stimulus-organism-response (SOR) framework, the research model was tested using the partial least squares structural equation modeling (PLS-SEM) technique with a questionnaire applied to 731 respondents from Saudi Arabia. Findings: The results showed that perceived quality, consumer satisfaction, and brand image have a positive impact on purchase intention, whereas perceived price could not explain purchase intention. Moreover, consumer satisfaction and brand image appeared to significantly mediate the relationships in the research model. Research limitations/implications: This article studies a specific country and local dairy consumption. One should be careful when generalizing the results to other food and country contexts. Originality/value: This study investigates consumer purchase intention specifically toward local dairy products, which was a matter underexplored in the literature as opposed to studies on a variety of other local products. Moreover, the article contributes to an extension of the SOR framework onto the body of literature regarding local products.


2019 ◽  
Vol 10 (6) ◽  
pp. 32
Author(s):  
Feixiang Zhang ◽  
Yang Yang

The paper adopts SPSS19.0 and AMOS20 to conduct an empirical study on the effects of e online bookstore perceived quality on consumer loyalty and the mediated effect of consumer satisfaction on the relationship, based on a 217 questionnaire data. The results show that online bookstore perceived quality does not have a significant positive effect on consumer loyalty; online bookstore perceived quality has a significant positive effect on online purchasing consumer satisfaction; online shopping consumer satisfaction has a significant positive effect on consumer loyalty; consumer satisfaction has a total mediating effect on the relationship between online bookstore perceived quality and customer loyalty and online bookstore perceived quality has a significant positive effect on consumer loyalty through consumer satisfaction. In order to fully play the mediating role of consumer satisfaction to improve the online bookstore consumer loyalty, the article puts forward related suggestions. The future research should expand the sample range and consider roles of other factors on the relationship. 


2020 ◽  
Vol 8 (2) ◽  
pp. 162
Author(s):  
DODY AL'AZHAR

Product quality control is very important for company or business that is willing to improve the performance. Home Industry Business or a home-based business established by Mr. Karsidin is furniture business and the products include cabinet, table, bench, TV rack and other furniture items which can be tailored to customer desires. In the production process, Mr. Karsidin's business still has product defects that can be observed at the beginning of this study that is presented in table 1.1. The study aims to determine the product quality level is still in control limits measurement of Mr. Karsidin’s Home Industry Business, analyze types of defects and control production quality using statistical quality control (SQC). The method in the study was statistical quality control (SQC) to monitor standards, make measurements and take corrective actions while the product or service is being produced. The quality control tools were Observation Sheet, Histogram, Cause and Effect Diagram and Control Diagram (p Chart). The result indicates that the product quality by Mr. Karsidin's business during the observation period from April to May 2019 is at the control limit. Further, based on p control analysis there is no point that exceeds Upper Limit or Lower Limit. The production process should be given more attention, especially at several main factors such as workers or human factors, in which there are a lot of negligence in the production process. Mr. Karsidin should make improvement to the defects directly that at the cause level, including raw material, machinery, method and human factors based on the Standard Operating Procedures (SOP).


Sensi Journal ◽  
2020 ◽  
Vol 6 (2) ◽  
pp. 236-246
Author(s):  
Ilamsyah Ilamsyah ◽  
Yulianto Yulianto ◽  
Tri Vita Febriani

The right and appropriate system of receiving and transferring goods is needed by the company. In the process of receiving and transferring goods from the central warehouse to the branch warehouse at PDAM Tirta Kerta Raharja, Tangerang Regency, which is currently done manually is still ineffective and inaccurate because the Head of Subdivision uses receipt documents, namely PPBP and mutation of goods, namely MPPW in the form of paper as a submission media. The Head of Subdivision enters the data of receipt and mutation of goods manually and requires a relatively long time because at the time of demand for the transfer of goods the Head of Subdivision must check the inventory of goods in the central warehouse first. Therefore, it is necessary to hold a design of information systems for the receipt and transfer of goods from the central warehouse to a web-based branch warehouse that is already database so that it is more effective, efficient and accurate. With the web-based system of receiving and transferring goods that are already datatabed, it can facilitate the Head of Subdivision in inputing data on the receipt and transfer of goods and control of stock inventory so that the Sub Head of Subdivision can do it periodically to make it more effective, efficient and accurate. The method of data collection is done by observing, interviewing and studying literature from various previous studies, while the system analysis method uses the Waterfall method which aims to solve a problem and uses design methods with visual modeling that is object oriented with UML while programming using PHP and MySQL as a database.


2013 ◽  
Vol 19 (1) ◽  
pp. 28
Author(s):  
Hamda Situmorang ◽  
Manihar Situmorang

Abstract Implementation of demonstration method in the teaching of chemistry is assigned as the right strategy to improve students’ achievement as it is proved that the method can bring an abstract concept to reality in the class. The study is conducted to vocational high school students in SMKN1 Pargetteng getteng Sengkut Pakfak Barat at accademic year 2013. The teaching has been carried out three cycles on the teaching of chemistry topic of colloid system. In the study, the class is divided into two class, experiment class and control class. The demontration method is used to teach students in experimental class while the teaching in control class is conducted with lecture method. Both are evaluated by using multiple choise tests before and after the teaching procedures, and the ability of students to answer the problems are assigned as students’ achievements. The results showed that demonstration method improved students’ achievement in chemistry. The students in experimental class who are taughed with demonstration method (M=19.08±0.74) have higher achievements compare with control class (M=12.91±2.52), and both are significantly different (tcalculation 22.85 > ttable 1.66). The effectivity of demostration method in experimental class (97%) is found higer compare to conventional method in control class (91%).


JEMAP ◽  
2020 ◽  
Vol 3 (1) ◽  
Author(s):  
Albertus Reynaldo Kurniawan ◽  
Bayu Prestianto

Quality control becomes an important key for companies in suppressing the number of defective produced products. Six Sigma is a quality control method that aims to minimize defective products to the lowest point or achieve operational performance with a sigma value of 6 with only yielding 3.4 defective products of 1 million product. Stages of Six Sigma method starts from the DMAIC (Define, Measure, Analyze, Improve and Control) stages that help the company in improving quality and continuous improvement. Based on the results of research on baby clothes products, data in March 2018 the percentage of defective products produced reached 1.4% exceeding 1% tolerance limit, with a Sigma value of 4.14 meaning a possible defect product of 4033.39 opportunities per million products. In the pareto diagram there were 5 types of CTQ (Critical to Quality) such as oblique obras, blobor screen printing, there is a fabric / head cloth code on the final product, hollow fabric / thin fabric fiber, and dirty cloth. The factors caused quality problems such as Manpower, Materials, Environtment, and Machine. Suggestion for consideration of company improvement was continuous improvement on every existing quality problem like in Manpower factor namely improving comprehension, awareness of employees in producing quality product and improve employee's accuracy, Strength Quality Control and give break time. Materials by making the method of cutting the fabric head, the Machine by scheduling machine maintenance and the provision of needle containers at each employees desk sewing and better environtment by installing exhaust fan and renovating the production room.


2019 ◽  
Vol 1 (1) ◽  
pp. 44
Author(s):  
Rony Trizudha ◽  
Sri Rahayuningsih ◽  
Ana Komari

As technology advances at this time, players in business are aware of the importance of product quality in the increasingly fierce competition in the industrial world due to the emergence of many similar companies. Therefore, companies must be able to compete to meet customer desires and try to retain customers. To maintain customers and their marketing areas, companies must have high competitiveness in order to survive by prioritizing quality improvement, increasing efficiency and increasing productivity to improve quality because by increasing quality, products can be accepted among consumers so that company goals can be fulfilled. Therefore, the company must carry out effective quality control which will result in high productivity, lower overall cost of making goods and the factors that cause production failure to be minimized. To improve quality, use the six sigma method, DMAIC and seven tools so that it can be known the cause of the damage and what actions are taken so that there needs to be a controversy to stabilize the processes of the production process so that we can know what percentage of damage and what factors cause damage, therefore there must be measurements and recommendations for improvement and control to reduce the causes From the analysis, it was found that the dent cup was 20.36%, the lid was 21.36% less dense, the lid was damaged in the finished product 18.72%, the cup was 19.28% less thick, the packaging was flexible 20.55%Seiring kemajuan teknologi pada saat ini pelaku di bisnis menyadari akan pentingnya kualitas produk dalam persaingan dunia industri yang semakin ketat karena banyak bermunculan perusahaan-perusahaan sejenis. Oleh sebab itu perusahaan harus dapat bersaing untuk memenuhi keinginan  pelanggan dan berusaha dapat mempertahankan pelanggan. Untuk mempertahankan pelangan dan wilayah pemasaranya perusahaan-perusahaan harus mempunyai daya saing yang tinggi untuk dapat bertahan dengan mengutamakan peningkatan mutu, peningkatan efisiensi dan peningkatan produktivitas untuk meningkatkan kualitas karena dengan peningkatan kualitas, produk dapat diterima di kalangan konsumen sehingga tujuan perusahaan dapat terpenuhi. Maka dari itu perusahaan harus melakukan pengendalian kualitas yang efektif akan menghasilkan produktivitas yang tinggi, biaya pembuatan barang keseluruhan yang lebih  rendah serta  faktor-faktor yang menyebabkan kegagalan produksi akan dapat ditekan sekecil mungkin. Untuk meningkatkan kualitas mengunakan metode six sigma, DMAIC dan seven tools agar dapat diketahui penyebab  kerusakan  dan  tindakan  apa  saja  yang dilakukan sehingga perlu ada kontror untuk menstabilkan  peoses proses produksi sehinga dapat di ketahui berapa persen  kerusakan dan faktor-faktor apa saja yang menyebabkan  kerusakan maka dari itu harus ada pengukuran dan  rekomendasi perbaikan serta melakukan kontrol untuk mengurangi penyebab kerusakan. Dari hasil analisis  di ketahui cup  penyok 20,36%, lid kurang  rapat  21,36%, lid  rusak  pada produk jadi 18,72%,cup kurang tebal 19,28 %kemasan lentur 20,55%


Sign in / Sign up

Export Citation Format

Share Document