scholarly journals Rekrontruksi Mesin Frais Ajax Universal Model No. 2A Mark V Di Bengkel Mekanik Polman Negeri Bangka Belitung

2019 ◽  
Vol 10 (02) ◽  
pp. 53-58
Author(s):  
Pristiansyah Pristiansyah
Keyword(s):  
Speed Control ◽  
Axial Direction ◽  
Milling Machine ◽  
Test Results ◽  
Machine Model ◽  
Vibration Machine ◽  
Machine Vibration ◽  
Second Stage ◽  
Last Stage ◽  
Rotary Speed

Mechanical workshop in Polman Bangka Belitung has 8 units Ajax Universal Milling Machine Model No. 2A Mark V. The condition of the engine can not be used maximum, for example a milling machine with a serial number FR12. This machine was damaged at the rotary speed control (rpm) and need repairing process. This study aims to analyze the types and causes damage to the rotary speed control, repair the damaged components and assemble the components to make it functioned with the standard engine. This research is devide in several stages, the first stage is analyzing the causes of the damage, the second stage is repairing and re-assembling the damage components. The last stage is testing for the repaired machine vibration by examining and comparing it with standard and permitted vibration machine and another machine which still good. The test results of the vibration machine is 0.884 mm / s rms for the axial direction and 0.938 mm / s rms for the radial direction. The summary, the vibration is still at the allowed limit which is equal to 1.12 mm / s rms and it means the machine is ready to use.

Performance Modeling of Desiccant Wheels: 1 — Model Development

2008 ◽  
Author(s):  
Chaoqin Zhai ◽  
David H. Archer ◽  
John C. Fischer
Keyword(s):  
Model Development ◽  
Axial Direction ◽  
Performance Model ◽  
Design Parameters ◽  
Residual Water ◽  
One Dimensional ◽  
Operating Variables ◽  
Steady State Operation ◽  
Rotary Speed ◽  
The Impact

This paper presents the development of an equation based model to simulate the combined heat and mass transfer in the desiccant wheels. The performance model is one dimensional in the axial direction. It applies a lumped formulation in the thickness direction of the desiccant and the substrate. The boundary conditions of this problem represent the inlet outside/process and building exhaust/regeneration air conditions as well as the adiabatic condition of the two ends of the desiccant composite. The solutions of this model are iterated until the wheel reaches periodic steady state operation. The modeling results are obtained as the changes of the outside/process and building exhaust/regeneration air conditions along the wheel depth and the wheel rotation. This performance model relates the wheel’s design parameters, such as the wheel dimension, the channel size and the desiccant properties, and the wheel’s operating variables, such as the rotary speed and the regeneration air flowrate, to its operating performance. The impact of some practical issues, such as wheel purge, residual water in the desiccant and the wheel supporting structure, on the wheel performance has also been investigated.

Application and Research of Digital Technology in Optimal Design of CNC Floor Boring and Milling Machine

2012 ◽  
Vol 429 ◽  
pp. 111-115
Author(s):  
Zhen Long Leng ◽  
Jin Feng Yang ◽  
Qun Ping Liu ◽  
Xun Deng
Keyword(s):  
Numerical Simulation ◽  
Optimal Design ◽  
Digital Technology ◽  
Three Dimensional ◽  
Milling Machine ◽  
Machine Model ◽  
Digital Modeling ◽  
Key Technologies ◽  
The Cost ◽  
Interference Checking

This paper focuses on application of the three-dimensional digital modeling, numerical analysis and optimization, digital control and other key technologies which provide technical support for the design and development in CNC floor boring and milling machine manufactruing. The three-dimensional digital modeling, digital assembly, interference checking help to eliminate some hidden trouble before processing and assembly. Numerical simulation reduces the cost and shortens the cycle of designand manufactruing in the optimal design of the machine. This technique has been successfully applied to a CNC Floor Boring and Milling Machine Model, which has been running for three years and achieved satisfactary economic result.

Implementasi CSR PT. Pos Indonesia Pada Program Bantuan Sarana Peribadatan

2020 ◽  
Vol 2 (3) ◽  
pp. 281-300
Author(s):  
Hadi Nurdin ◽  
Dang Eif Saiful Amin ◽  
Dyah Rahmi Astuti
Keyword(s):  
Research Method ◽  
Budget Management ◽  
Case Study Method ◽  
Assistance Program ◽  
Budget Planning ◽  
Second Stage ◽  
The Third ◽  
Third Stage ◽  
Last Stage

ABSTRAK Tulisan ini bertujuan untuk mengetahui implementasi  CSR PT. Pos Indonesia pada program bantuan sarana peribadatan mulai dari tahap perencanaan, pengorganisasian, pelaksanaan dan pengawasan. Metode penelitian ini menggunakan metode studi kasus untuk mengetahui karakteristik  dengan cara berinteraksi secara langsung dan mendalam mengenai sebuah kasus dan ringkasan yang digambarkan pada konteks di atas mendasari untuk menggali dan mendeskripsikan kegiatan-kegiatan divisi PKBL PT. Pos Indonesia. Analisis penelitian ini menggunakan deskriptif kualittaif. Hasil penelitian menunjukan bahwa Implementasi Kegiatan Responsibility CSR pada program bantuan sarana peribadatan, mulai dari tahap pertama yaitu perencanaan agenda proposal, peninjauan proposal, dan perencanaan anggaran. Tahap kedua yaitu tahap pengorganisasian dengan mengorganisasikan persiapan, mengorganisasikan koordinasi dan mengorganisasikan pengelolaan anggaran. Tahap ketiga yaitu tahap pelaksanaan melaksanan briefing, melaksanakan program dilapangan dan melaksankan penyaluran dan. Tahap terakhir yaitu pengawasan  mengawasi program, mengawasi dana yang telah disalurkan. Kata Kunci : CSR; Implementasi; Bantuan Sarana Peribadatan ABSTRACT This research aims to determine the implementation of CSR PT. Pos Indonesia in the assistance program for worship facilities starting from the planning, organizing, implementing and monitoring stages. This research method uses a case study method to find out the characteristics by interacting directly and deeply about a case and a summary illustrated in the above context is underlying to explore and describe the activities of the PKBL division of PT. Indonesian post. The analysis of this study uses descriptive qualitative. The results of the study show that the implementation of CSR Responsibility Activities in the worship facilities assistance program, starting from the first stage, namely planning the proposal agenda, reviewing proposals, and budget planning. The second stage is the organizing stage by organizing preparations, organizing coordination and organizing budget management. The third stage is the stage of carrying out the briefing, implementing the program in the field and implementing the distribution and. The last stage is supervision overseeing the program, overseeing the funds that have been channeled. Keywords : CSR; Implementation; Religious Facilities Assistance

scholarly journals Equivalent Malay-Arabic Data Corpus Collection

2016 ◽  
Vol 4 (1) ◽  
pp. 65 ◽  
Author(s):  
Taj Rijal Muhamad Romli ◽  
Abd Rauf Hassan ◽  
Hasnah Mohamad
Keyword(s):  
Search Strategy ◽  
High Impact ◽  
Universal Theory ◽  
World Cup ◽  
Second Stage ◽  
The Third ◽  
Sentence Level ◽  
The Press ◽  
Third Stage ◽  
Last Stage

This paper aims to introduce a search strategy and collecting comparable sentences of Arab-Malay corpus data. This method was introduced for the use of students, researchers and amateur translators to search and compare the structure of sentences in Arabic and Malay. The first stage is to collect data corpus with high impact titles from the press and must be able to enlarge the scope of study as stated by Maia (2003). The second stage is to search using the specified key words based on selected high-impact titles such as the Football World Cup year 2010 and 2014. Data search is by using Webcorp engine http://www.webcorp.org.uk/live/ corpus and also open database Google https://www.google.com. The third stage is to filter the data by using Aker et.al (2012) and Braschler's (1998) method based on similar story, related story and similar aspects. At the fourth stage every category is measured by Guidere's (2002) equivalence strength which is strong comparability (SC), medium (MC) and weak (WC). At the last stage comparable sentences between the two languages are compiled in parallel according to Mona Baker’s (1992) level of grouping which are sentence level, combination of words, grammatical, pragmatic and textual level. The result from data analysis based on Mona Baker and Vinay - Darbelnet’s (1995) comparable theory proved the existence of some sentences in large quantities are on the same level of comparability from the point of information delivery. This can be used as the basis of additional evidence concerning the validity of 'universal theory.' in the science of translation.

scholarly journals Proses Pembuatan Hidrolisat Protein Ikan Rucah

2012 ◽  
Vol 13 (3) ◽  
pp. 256
Author(s):  
Dyah Koesoemawardani ◽  
Fibra Nurainy ◽  
Sri Hidayati
Keyword(s):  
Soluble Protein ◽  
Emulsion Stability ◽  
Enzyme Concentration ◽  
Test Results ◽  
Fish Protein ◽  
Protein Hydrolyzate ◽  
Second Stage ◽  
Trash Fish ◽  
Two Stages ◽  
Fish Protein Hydrolysates

This study aimed to find optimum manufacturing trash fish protein hydrolyzate using the commercial papainenzyme. It is known that fish protein hydrolysates have good functional properties, so it is more widely utilized,especially for food. The study was conducted in two stages, the first stage was to make trash fish protein hydrolyzatetreated with enzyme concentration of 3%, 5%, 7% (w/w), and pH 5; 5.5; 6; 6.5; 7, whereas second stage was to maketrash fish protein hydrolyzate with same from the first stage and so the best treatment followed by treatment ofhalf-hour long incubation and one hour. Parameters observed were soluble protein, foamability, fat binding capacityand emulsion stability. The treatment was repeated three times and the first phase of data analysis using advancedtesting LSD and the second stage using the T test. Results show that the best soluble protein to produce a trashfish protein hydrolyzate enzyme was at a concentration of 5% and pH = 6.5 that was equal to 19.71%. In half an hourincubation produce higher soluble protein values and foamability that were equal to 24.97% and 9.63%, while thebinding capacity of fat in one hour incubation produces a higher value that was equal to 5.03%. Meanwhile, emulsionstability did not differ significantly at both incubation time.

scholarly journals Study on Suitability and Behaviour of Ferrocement in Folded Plates

2021 ◽  
Vol 9 (VI) ◽  
pp. 3540-3546
Author(s):  
Mr. V. Karthick
Keyword(s):  
Stainless Steel ◽  
Compressive Strength ◽  
Cross Section ◽  
Test Results ◽  
Logical Investigation ◽  
Second Stage ◽  
Concrete Application ◽  
Extended Range ◽  
Properties Of Materials ◽  
Low Consumption

Ferro concrete is one of the developments arising material an alternative for the traditional RCC in numerous viewpoints. Ferro concrete is the fate of the minimal expense houses and precast houses. Folded plates are answer for the more extended range rooftops in prudent and aesthetical manner. This project consolidates the upsides of both Ferro concrete and collapsed plate. The box type Ferro concrete collapsed plates of size 0.6 m x 1.80 m x 0.15 m are casted by thinking about various diaries and RCC collapsed plates in thought while fixing dimensions. In first period of trial various properties of materials utilized for projecting are tried and compressive strength of the mortar utilized is tried, the test is done at 1:2 of concrete: sand proportion and 0.35 water concrete ratio. In second stage the example is casted with Stainless Steel cross section of 2 mm opening is utilized and 2 layers on front and posteriors of 6mm width 150m divided skeleton steel is laid. The projected examples is tried for 28 days strength in stacking outline and the outcomes are contrasted and logical investigation Using ANSYS for load versus redirection and reasonableness of Ferro concrete application in collapsed plates are studies. The test results are shown acceptable outcomes, at last with low consumption and low self-weight Ferro concrete constructions are acceptable substitute for RCC.

scholarly journals Dynamic model of speed control through ring gears in a device with a multistage gear differentials and closed-loop hydraulic systems

2020 ◽  
Vol 99 (3) ◽  
pp. 102-111
Author(s):  
O. Strilets
Keyword(s):  
Computer Simulation ◽  
Quantitative Analysis ◽  
Closed Loop ◽  
Speed Control ◽  
Dynamic Processes ◽  
The Sun ◽  
Hydraulic Systems ◽  
Lagrange Method ◽  
Last Stage ◽  
Gear Differential

The dynamic processes in the device for speed control with multistage gear differential and closed-loop hydraulic systems through ring gears have been studied for case when the leading link is the sun gear of the first stage, and the driven is a carrier of the last stage. For such a device, the equation of kinetic energy has been compiled and the dynamics equations have been obtained by the Lagrange method, which have been solved. The obtained results are the basis for further computer simulation on and quantitative analysis to assess the performance of such devices and select the necessary closed-loop hydraulic systems to control speed changes.

scholarly journals The Design Process at Le Corbusier, Case of the Ronchamp Chapel

2019 ◽  
Vol 1 (1) ◽  
pp. 1275-1282
Author(s):  
Nadjat Outmoune ◽  
Abdelmalek Arrouf
Keyword(s):  
Empirical Studies ◽  
Data Gathering ◽  
Le Corbusier ◽  
Generic Model ◽  
Design Activity ◽  
Genetic Method ◽  
Second Stage ◽  
Three Stages ◽  
Last Stage

AbstractThis work falls within the empirical studies of design activity. Its project is to understand Le Corbusier's designing way and how does he work and structure his design processes. Doing so, it jumps above the descriptive and doctrinal knowledge of objects produced by “Le Corbusier” to study the actions and mechanisms that led to them.To achieve its aim, this study uses genetic method, developed by P.M. De Biasi of literary origin, this research method is made of three stages. The first one, which is of empirical nature, is one of data gathering. It leads to the establishment of genesis tables and to the classification of the all collected documents. The second stage, makes the analysis of all the collected documents one by one. It allows the restitution of the creative process of one projects “Le Corbusier” which is “la chapelle de Notre Dame du haut de Ronchamp”. The last stage is finally that define the design processe of the this project. The results show that the design activity of “Le Corbuiser” obeys the overall logic of one generic model which may be called his individual designing style.

Wear Characteristics of Polycrystalline Diamond Compact Drill Bits in Small Diameter Rock Drilling

1985 ◽  
Vol 107 (4) ◽  
pp. 534-542 ◽  
Author(s):  
C. L. Hough ◽  
B. Das
Keyword(s):  
Small Diameter ◽  
Polycrystalline Diamond ◽  
Wear Test ◽  
Test Results ◽  
Failure Characteristics ◽  
Wear Characteristics ◽  
Drill Bits ◽  
Rotary Speed ◽  
Polycrystalline Diamond Compact ◽  
Single Material

The wear characteristics of polycrystalline diamond compact (PDC) drill bits were investigated in the context of drilling small holes in a hard abrasive medium. An efficient method for measuring wear of the PDC drill bits was developed. The wear test results were grouped or categorized in terms of rotary speed, feed and wear or failure characteristics. Contrary to the three classical wear phases (break-in, uniform wear and rapid breakdown) of the single material cutters, four distinctive wear phases were formed for the PDC cutters: I–break-in, II–diamond wear, III–carbide wear, and IV–rapid breakdown. The characteristics of the wear phases were identified and some suggestions were made to alleviate the wear problem.

Sign in / Sign up

Export Citation Format

Share Document