scholarly journals Experimental Study on the Surface Properties of Nanoalumina-Filled Epoxy Resin Nanocomposites

2020 ◽  
Vol 10 (3) ◽  
pp. 733 ◽  
Author(s):  
Pinto ◽  
Amaro ◽  
Bernardo
Keyword(s):  
Experimental Study ◽  
Surface Roughness ◽  
Epoxy Resin ◽  
Surface Properties ◽  
Weight Fraction ◽  
Maximum Size ◽  
Contact Angles ◽  
Diglycidyl Ether ◽  
Alumina Nanoparticles ◽  
Epoxy Resin Nanocomposites

This article presents an experimental study on the surface properties of epoxy resin nanocomposites (EPNCs) manufactured with a thermosetting epoxy resin (EP)–bisphenol A diglycidyl ether (BADGE)–2-[[4-[2-[4-(Oxiran-2-ylmethoxy)phenyl]propan-2-yl]phenoxy]methyl]oxirane) and filled with alumina nanoparticles (NPs). The NPs consist of pretreated (with a silane agent) alpha alumina with irregular shapes and a 100 nm maximum size. Three weight fractions of NPs were studied: 1, 3, and 5 wt. (%). Two different epoxy (EP) resins were manufactured, one cured and postcured with bis (4-aminophenyl) methane (DDM); and another one cured with 3-dodec-2-enyloxolane-2,5-dione (DDSA) + 8-methyl-3a,4,7,7a-tetrahydro-4,7-methano-2-benzofuran-1,3-dione (MNA). The wettability and the surface roughness of the obtained EPNCs were studied through the measurement of contact angles and topographic images obtained with atomic force microscopy (AFM), respectively. Significant influence of both the loading of NPs and used curing agents was observed. EPNCs cured with DDM were shown to be hydrophobic for 0, 1, and 3 wt. (%) and hydrophilic for 5 wt. (%). Maximum surface roughness was observed for 5 wt. (%). EPNCs cured with DDSA+MNA were shown to be hydrophilic for 0 and 1 wt. (%) and hydrophobic for 3 and 5 wt. (%). The surface roughness decreased as the weight fraction of NPs increased until 3 wt. (%), and then increased for 5 wt. (%).

scholarly journals Surface Properties of Pine Scrimber Panels with Varying Density

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 397 ◽  
Author(s):  
Jinguang Wei ◽  
Qiuqin Lin ◽  
Yahui Zhang ◽  
Wenji Yu ◽  
Chung-Yun Hse ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Photoelectron Spectroscopy ◽  
Lower Surface ◽  
Contact Angles ◽  
High Density ◽  
Water Contact ◽  
Change Rate ◽  
Hydrophilic Material ◽  
Wood Grain

Coating quality for scrimber products against exterior conditions is largely dependent on the surface properties. The wettability, morphology, and chemical composition of pine scrimber surfaces were investigated to better understand the surface properties. The scrimber was found to be a hydrophilic material because the water contact angles were less than 90°. The panels with a density of 1.20 g/cm3 had the largest angle change rate (k = 0.212). As the panel density increased, the instantaneous contact angle of each test liquid (i.e., water, formamide, and diiodomethane) on the panels decreased, and so did surface free energy. Panels with higher density showed lower surface roughness. Surface roughness across the wood grain was greater than that along the grain. SEM observations showed the high-density panels had a smoother surface with fewer irregular grooves in comparison with the low-density panels. X-ray photoelectron spectroscopy (XPS) analysis indicated that more unoxygenated groups appeared on the surface of high-density panels.

scholarly journals Surface Properties of Poly(Hydroxyurethane)s Based on Five-Membered Bis-Cyclic Carbonate of Diglycidyl Ether of Bisphenol A

Materials ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5184
Author(s):  
Mariusz Tryznowski ◽  
Zuzanna Żołek-Tryznowska
Keyword(s):  
Bisphenol A ◽  
Surface Properties ◽  
Rheological Characteristic ◽  
13C Nmr Spectroscopy ◽  
Cyclic Carbonate ◽  
Contact Angles ◽  
Diglycidyl Ether ◽  
Scanning Calorimetry ◽  
Static Contact ◽  
Ft Ir

Poly(hydroxyurethane)s (PHU) are alternatives for conventional polyurethanes due to the use of bis-cyclic dicarbonates and diamines instead of harmful and toxic isocyanates. However, the surface properties of poly(hydroxyurethane)s are not well known. In this work, we focus on the analysis of the surface properties of poly(hydroxyurethane) coatings. Poly(hydroxyurethane)s were obtained by a catalyst-free method from commercially available carbonated diglycidyl ether of bisphenol A (Epidian 6 epoxy resins) and various diamines: ethylenediamine, trimethylenediamine, putrescine, hexamethylenediamine, 2,2,4(2,4,4)-trimethyl-1,6-hexanediamine, m-xylylenediamine, 1,8-diamino-3,6-dioxaoctane, 4,7,10-trioxa-1,13-tridecanediamine, and isophorone diamine, using a non-isocyanate route. The structures of the obtained polymers were confirmed by FT-IR, 1H NMR and 13C NMR spectroscopy, and thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyses were performed. The rheological characteristic of the obtained polymers is presented. The static contact angles of water, diidomethane, and formamide, deposited on PHU coatings, were measured. From the measured contact angles, the surface free energy was calculated using two different approaches: Owens–Wendt and van Oss–Chaudhury–Good. Moreover, the wetting envelopes of PHU coatings were plotted, which enables the prediction of the wetting effect of various solvents. The results show that in the investigated coatings, a mainly dispersive interaction occurs.

The Wetting of Insect Cuticles by Water

1955 ◽  
Vol 32 (3) ◽  
pp. 591-617 ◽  
Author(s):  
M. W. HOLDGATE
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Surface Properties ◽  
Surface Composition ◽  
Contact Angles ◽  
Aquatic Species ◽  
Water Contact ◽  
Calliphora Erythrocephala ◽  
Wetting Properties ◽  
Wide Range

1. The water contact angles of insects show a wide range of variation, which is broadly correlated with surface roughness and with habitat. 2. The contact angles of species inhabiting stored products or carrion are greatly modified by contamination. This produces large variations between apparently similar individuals. 3. In terrestrial insects surface roughness increases the contact angles to very large apparent values. Detailed analyses of its effect have been made in the pupa of Tenebrio molitor and the adult Calliphora erythrocephala. In some aquatic insects surface roughness leads to a reduction in the contact angles; this has been studied in the nymph of Anax imperator. 4. Prolonged immersion in water causes a lowering of the contact angles of all the insects examined, and the low angles of many aquatic species may therefore be the direct effect of their environment. In some aquatic species there is evidence of the active maintenance of a large contact angle during life. 5. Changes in contact angle accompany processes of cuticle secretion and will occur at any moult if changes in roughness or habitat take place. 6. The observed variations of surface properties can be explained without assuming any variation in the chemical composition of the cuticle surface. Wetting properties are of little value as indicators of cuticle surface composition. 7. The biological aspects of insect surface properties are briefly discussed.

scholarly journals Influence of Surface Properties on Adhesion Forces and Attachment ofStreptococcus mutansto ZirconiaIn Vitro

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Pei Yu ◽  
Chuanyong Wang ◽  
Jinglin Zhou ◽  
Li Jiang ◽  
Jing Xue ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Properties ◽  
Biofilm Formation ◽  
Adhesion Force ◽  
Contact Angles ◽  
Adhesion Forces ◽  
Force Microscopy ◽  
Early Attachment ◽  
Atomic Force ◽  
Initial Adhesion

Zirconia is becoming a prevalent material in dentistry. However, any foreign bodies inserted may provide new niches for the bacteria in oral cavity. The object of this study was to explore the effect of surface properties including surface roughness and hydrophobicity on the adhesion and biofilm formation ofStreptococcus mutans(S. mutans) to zirconia. Atomic force microscopy was employed to determine the zirconia surface morphology and the adhesion forces between theS. mutansand zirconia. The results showed that the surface roughness was nanoscale and significantly different among tested groups (P<0.05): Coarse (23.94±2.52 nm) > Medium (17.00±3.81 nm) > Fine (11.89±1.68 nm). The contact angles of the Coarse group were the highest, followed by the Medium and the Fine groups. Increasing the surface roughness and hydrophobicity resulted in an increase of adhesion forces and early attachment (2 h and 4 h) ofS. mutanson the zirconia but no influence on the further development of biofilm (6 h~24 h). Our findings suggest that the surface roughness in nanoscale and hydrophobicity of zirconia had influence on theS. mutansinitial adhesion force and early attachment instead of whole stages of biofilm formation.

Experimental study on the mechanical properties of an epoxy-based nanocomposite using polymeric alloying and different nano-reinforcements: nanofiber, nanolayered and nanoparticulate materials

2015 ◽  
Vol 22 (6) ◽  
Author(s):  
Yasser Rostamiyan ◽  
Abdolhossein Fereidoon ◽  
Amin Hamed Mashhadzadeh
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Carbon Nanotube ◽  
Bisphenol A ◽  
Epoxy Resin ◽  
Diglycidyl Ether ◽  
Epoxy System ◽  
Different Types ◽  
Multi Wall Carbon Nanotube

AbstractThis study investigated the effect of four different types of reinforcements on the mechanical properties of an epoxy system. The epoxy resin used was diglycidyl ether of bisphenol A (DGEBA) cured by cycloaliphatic polyamine. These four mechanisms use a multi-wall carbon nanotube (MWCNT) as a nanofiber, clay as a nanolayer, SiO

scholarly journals Interface Characterization of Epoxy Resin Nanocomposites: A Molecular Dynamics Approach

Fibers ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 54 ◽  
Author(s):  
Carlos Sáenz Ezquerro ◽  
Manuel Laspalas ◽  
Agustín Chiminelli ◽  
Francisco Serrano ◽  
Clara Valero
Keyword(s):  
Molecular Dynamics ◽  
Epoxy Resin ◽  
Polymer Nanocomposites ◽  
Materials Science ◽  
General Rule ◽  
Diglycidyl Ether ◽  
Interface Region ◽  
Cross Linking ◽  
Interface Thickness ◽  
Epoxy Resin Nanocomposites

In polymer nanocomposites, the interface region between the matrix and the fillers has been identified as a key interaction region that strongly determines the properties of the final material. Determining its structure is crucial from several points of view, from modeling (i.e., properties prediction) to materials science (i.e., understanding properties/structure relationships). In the presented paper, a method for characterizing the interface region of polymer nanocomposites is described using molecular dynamics (MD) simulations. In particular, the structure of the polymer within the interface region together with its dimension in terms of thickness were analyzed through density profiles. Epoxy resin nanocomposites based on diglycidyl ether of bisphenol A (DGEBA) were studied using this approach, and the interface region with triple walled carbon nanotubes (TWCNT) and carbon fibers (CF) was characterized. The effect of carbon nanotube diameter, type of hardener, and effect of epoxy resin cross-linking degree on interface thickness were analyzed using MD models. From this analysis no general rule on the effect of these parameters on the interface thickness could be established, since in some cases overlapping effects between the analyzed parameters were observed, and each specific case needs to be analyzed independently in detail. Results show that the diameter has an impact on interface thickness, but this effect is affected by the cross-linking degree of the epoxy resin. The type of hardener also has a certain influence on the interface thickness.

scholarly journals Apparent Surface Free Energy of Polymer/Paper Composite Material Treated by Air Plasma

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Konrad Terpiłowski
Keyword(s):  
Surface Roughness ◽  
Free Energy ◽  
Plasma Treatment ◽  
Surface Properties ◽  
Surface Free Energy ◽  
Photoelectron Spectroscopy ◽  
Contact Angles ◽  
Air Plasma ◽  
Surface Plasma ◽  
Composite Surface

Surface plasma treatment consists in changes of surface properties without changing internal properties. In this paper composite polymer/paper material is used for production of packaging in cosmetic industry. There are problems with bonding this material at the time of packaging production due to its properties. Composite surface was treated by air plasma for 1, 10, 20, and 30 s. The advancing and receding contact angles of water, formamide, and diiodomethane were measured using both treated and untreated samples. Apparent surface free energy was estimated using the hysteresis (CAH) and Van Oss, Good, Chaudhury approaches (LWAB). Surface roughness was investigated using optical profilometry and identification of after plasma treatment emerging chemical groups was made by means of the XPS (X-ray photoelectron spectroscopy) technique. After plasma treatment the values of contact angles decreased which is particularly evident for polar liquids. Apparent surface free energy increased compared to that of untreated samples. Changes of energy value are due to the electron-donor parameter of energy. This parameter increases as a result of adding polar groups at the time of surface plasma activation. Changes of surface properties are combination of increase of polar chemical functional groups, increase on the surface, and surface roughness increase.

Investigation of treated PEN foil surface properties for inkjet application

2015 ◽  
Vol 27 (3) ◽  
pp. 108-111
Author(s):  
Aneta Araźna ◽  
Konrad Futera ◽  
Małgorzata Jakubowska ◽  
Łucja Dybowska-Sarapuk
Keyword(s):  
Surface Roughness ◽  
Contact Angle ◽  
Glow Discharge ◽  
Surface Properties ◽  
Contact Angles ◽  
Polyethylene Naphthalate ◽  
Content Type ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Afm Micrographs

Purpose – The purpose of this paper is to report surface properties of treated Teonex Du Pont polyethylene naphthalate (PEN) foil substrates. Design/methodology/approach – There were three different cleaning treatments among other: argon glow discharge, dipping into alkaline solution at 60°C as well as washing in an ultrasonic bath of acetone and ethyl alcohol in room temperature. The relation between PEN foil morphology and surface properties has been studied by contact angle measurements as well as evaluation of surface roughness of PEN foil samples by atomic force microscopy (AFM). Findings – It was found that argon glow discharge (T3) of PEN treatment caused the maximum reduction in both values of contact angles. In addition, the argon glow discharge yielded the highest PEN surface energy (51.9 mJ/m2) and polarity (0.89). On the other hand, the AFM micrographs showed that the samples T3 had the highest value of average and root mean square surface roughness. Based on the experiments results, the authors stated that the alkaline cleaning (T2 treatment) could be considered as an effective method of PEN substrate treatment. Originality/value – The influence of different cleaning treatment on the surface properties of PEN foil to inkjet application was analyzed. In the literature, there are not a lot of papers describing examinations of surface properties of PEN foil to inkjet application by contact angle measurements and AFM analysis.

Sign in / Sign up

Export Citation Format

Share Document