A New Method to Lightweight Magnesium Using Syntactic Composite Core

Light weighting of magnesium-based materials is crucial for its extensive use in transportation applications. Hybrid processing of these materials in a shell-core pattern can substantially improve the specific properties of magnesium. In the present study, the Mg/Mg-20GMB (glass microballoon) hybrid composite was prepared using a disintegrated melt deposition technique. Microstructural characterization and mechanical properties of the developed as-cast Mg/Mg-20GMB hybrid composite were investigated. Results revealed that a unified metallurgical interface was formed between the Mg-20GMB core material and the pure Mg shell. Energy dispersive X-ray spectroscopy (EDX) results confirmed the existence of Mg2Si as the secondary phase in the Mg-20GMB core material. The hybrid Mg/Mg-20GMB composite exhibited much superior compressive yield strength (↑71.6%), lower ultimate compressive strength (↓23.25%), and enhanced ductility (↑186.48%) when compared to as-cast pure magnesium.

Download Full-text

A Novel Method of Light Weighting Aluminium Using Magnesium Syntactic Composite Core

Crystals ◽

10.3390/cryst10100917 ◽

2020 ◽

Vol 10 (10) ◽

pp. 917

Author(s):

Penchal Reddy Matli ◽

Joshua Goh Yong Sheng ◽

Gururaj Parande ◽

Vyasaraj Manakari ◽

Beng Wah Chua ◽

...

Keyword(s):

Mechanical Properties ◽

Compressive Strength ◽

Hybrid Composite ◽

Compressive Loading ◽

Core Region ◽

Core Material ◽

Novel Method ◽

Light Weighting ◽

Melt Deposition ◽

Shell Region

In this study, hybrid composite consisting of aluminium (Al) shell and magnesium/glass microballoon (Mg-20 wt.% GMB) syntactic composite core was fabricated in a shell-core pattern by combining powder metallurgy and disintegrated melt deposition (DMD) techniques. Physical, microstructural and mechanical properties of as-cast Al and Al/Mg-20GMB hybrid composite were examined. Approximately 13% reduction in density (with respect to aluminium) was realized through the use of a syntactic composite core. Microstructural investigations revealed reasonable interfacial integrity between aluminium shell and Mg-GMB core material and the presence of Al, Mg and GMB phases. The interface region showed a hardness of 109 ± 2 Hv in comparison to the hardness of Al shell region (68 ± 4 Hv) and Mg-20GMB core region (174 ± 5 Hv). In comparison to as-cast Al, the yield strength and ultimate compressive strength of the as-cast Al/Mg-20GMB hybrid composite increased by ~65.4% and ~60%, respectively. Further, the energy absorption under compressive loading for the Al/Mg-20GMB hybrid composite was ~26% higher compared to pure Al. This study validated that Al/Mg-20GMB hybrid composite with superior absolute and specific mechanical properties can be fabricated and used for weight critical applications.

Download Full-text

Functional Bionanocomposite Fibers of Chitosan Filled with Cellulose Nanofibers Obtained by Gel Spinning

Polymers ◽

10.3390/polym13101563 ◽

2021 ◽

Vol 13 (10) ◽

pp. 1563

Author(s):

Sofia Marquez-Bravo ◽

Ingo Doench ◽

Pamela Molina ◽

Flor Estefany Bentley ◽

Arnaud Kamdem Tamo ◽

...

Keyword(s):

Mechanical Properties ◽

Mechanical Performance ◽

Cellulose Nanofibers ◽

Microstructural Characterization ◽

Fiber Formation ◽

Fiber Direction ◽

Composite Fibers ◽

X Ray Diffraction ◽

Gel Spinning ◽

X Ray

Extremely high mechanical performance spun bionanocomposite fibers of chitosan (CHI), and cellulose nanofibers (CNFs) were successfully achieved by gel spinning of CHI aqueous viscous formulations filled with CNFs. The microstructural characterization of the fibers by X-ray diffraction revealed the crystallization of the CHI polymer chains into anhydrous chitosan allomorph. The spinning process combining acidic–basic–neutralization–stretching–drying steps allowed obtaining CHI/CNF composite fibers of high crystallinity, with enhanced effect at incorporating the CNFs. Chitosan crystallization seems to be promoted by the presence of cellulose nanofibers, serving as nucleation sites for the growing of CHI crystals. Moreover, the preferential orientation of both CNFs and CHI crystals along the spun fiber direction was revealed in the two-dimensional X-ray diffraction patterns. By increasing the CNF amount up to the optimum concentration of 0.4 wt % in the viscous CHI/CNF collodion, Young’s modulus of the spun fibers significantly increased up to 8 GPa. Similarly, the stress at break and the yield stress drastically increased from 115 to 163 MPa, and from 67 to 119 MPa, respectively, by adding only 0.4 wt % of CNFs into a collodion solution containing 4 wt % of chitosan. The toughness of the CHI-based fibers thereby increased from 5 to 9 MJ.m−3. For higher CNFs contents like 0.5 wt %, the high mechanical performance of the CHI/CNF composite fibers was still observed, but with a slight worsening of the mechanical parameters, which may be related to a minor disruption of the CHI matrix hydrogel network constituting the collodion and gel fiber, as precursor state for the dry fiber formation. Finally, the rheological behavior observed for the different CHI/CNF viscous collodions and the obtained structural, thermal and mechanical properties results revealed an optimum matrix/filler compatibility and interface when adding 0.4 wt % of nanofibrillated cellulose (CNF) into 4 wt % CHI formulations, yielding functional bionanocomposite fibers of outstanding mechanical properties.

Download Full-text

Phase Formation, Microstructure and Mechanical Properties of Mg67Ag33 as Potential Biomaterial

Metals ◽

10.3390/met11030461 ◽

2021 ◽

Vol 11 (3) ◽

pp. 461

Author(s):

Konrad Kosiba ◽

Konda Gokuldoss Prashanth ◽

Sergio Scudino

Keyword(s):

Mechanical Properties ◽

Young’S Modulus ◽

Young's Modulus ◽

Equilibrium Phase ◽

Antibacterial Properties ◽

Equilibrium Phase Diagram ◽

Compressive Yield Strength ◽

X Ray ◽

Fine Grained ◽

Equilibrium Phases

The phase and microstructure formation as well as mechanical properties of the rapidly solidified Mg67Ag33 (at. %) alloy were investigated. Owing to kinetic constraints effective during rapid cooling, the formation of equilibrium phases is suppressed. Instead, the microstructure is mainly composed of oversaturated hexagonal closest packed Mg-based dendrites surrounded by a mixture of phases, as probed by X-ray diffraction, electron microscopy and energy dispersive X-ray spectroscopy. A possible non-equilibrium phase diagram is suggested. Mainly because of the fine-grained dendritic and interdendritic microstructure, the material shows appreciable mechanical properties, such as a compressive yield strength and Young’s modulus of 245 ± 5 MPa and 63 ± 2 GPa, respectively. Due to this low Young’s modulus, the Mg67Ag33 alloy has potential for usage as biomaterial and challenges ahead, such as biomechanical compatibility, biodegradability and antibacterial properties are outlined.

Download Full-text

CuOX Films for NO2 Detection: Microstructural Characterization

Applied Mechanics and Materials ◽

10.4028/www.scientific.net/amm.481.133 ◽

2013 ◽

Vol 481 ◽

pp. 133-136 ◽

Cited By ~ 3

Author(s):

T.N. Myasoedova ◽

G.E. Yalovega ◽

N.K. Plugotarenko ◽

M. Brzhezinskaya ◽

V.V. Petrov ◽

...

Keyword(s):

Gas Sensors ◽

Secondary Electron ◽

Operating Temperature ◽

Sol Gel ◽

Microstructural Characterization ◽

Temperature Treatment ◽

Copper Oxides ◽

Edge Structure ◽

X Ray ◽

X Ray Absorption

Copper oxides films as promising materials for gas sensors applications were studied. Copper oxide films were deposited onto Si/SiO2substrates using a citrate sol-gel method with the subsequent temperature treatment at 150-5000C. These films were characterized by means of secondary electron microscopy (SEM) and X-ray-absorption near-edge structure (XANES) spectroscopy. The prepared films were utilized in NO2sensors. The dependences of the NO2response on the operating temperature and NO2concentration (10-200 ppm) were investigated. The maximum NO2response was achieved for the film annealed at 2500C.

Download Full-text

A Highly Sensitive Room Temperature CO2 Gas Sensor Based on SnO2-rGO Hybrid Composite

Materials ◽

10.3390/ma14030522 ◽

2021 ◽

Vol 14 (3) ◽

pp. 522

Author(s):

Zhi Yan Lee ◽

Huzein Fahmi bin Hawari ◽

Gunawan Witjaksono bin Djaswadi ◽

Kamarulzaman Kamarudin

Keyword(s):

Electron Microscopy ◽

Carbon Dioxide ◽

Gas Sensor ◽

Photoelectron Spectroscopy ◽

Hybrid Composite ◽

Room Temperature ◽

Co2 Gas ◽

X Ray ◽

Wide Range ◽

Co2 Gas Sensor

A tin oxide (SnO2) and reduced graphene oxide (rGO) hybrid composite gas sensor for high-performance carbon dioxide (CO2) gas detection at room temperature was studied. Since it can be used independently from a heater, it emerges as a promising candidate for reducing the complexity of device circuitry, packaging size, and fabrication cost; furthermore, it favors integration into portable devices with a low energy density battery. In this study, SnO2-rGO was prepared via an in-situ chemical reduction route. Dedicated material characterization techniques including field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray (EDX) spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) were conducted. The gas sensor based on the synthesized hybrid composite was successfully tested over a wide range of carbon dioxide concentrations where it exhibited excellent response magnitudes, good linearity, and low detection limit. The synergistic effect can explain the obtained hybrid gas sensor’s prominent sensing properties between SnO2 and rGO that provide excellent charge transport capability and an abundance of sensing sites.

Download Full-text

Electronic Impact of Inclusions in Diamond

MRS Proceedings ◽

10.1557/proc-1203-j17-19 ◽

2009 ◽

Vol 1203 ◽

Cited By ~ 4

Author(s):

Erik M. Muller ◽

John Smedley ◽

Balaji Raghothamachar ◽

Mengjia Gaowei ◽

Jeffrey W. Keister ◽

...

Keyword(s):

Charge Trapping ◽

Secondary Phase ◽

Surface Region ◽

Phase Region ◽

Electron Trapping ◽

Near Surface ◽

X Ray ◽

Photoconductive Gain ◽

Single Crystal Diamond ◽

Topography Data

AbstractX-ray topography data are compared with photodiode responsivity maps to identify potential candidates for electron trapping in high purity, single crystal diamond. X-ray topography data reveal the defects that exist in the diamond material, which are dominated by non-electrically active linear dislocations. However, many diamonds also contain defects configurations (groups of threading dislocations originating from a secondary phase region or inclusion) in the bulk of the wafer which map well to regions of photoconductive gain, indicating that these inclusions are a source of electron trapping which affect the performance of diamond X-ray detectors. It was determined that photoconductive gain is only possible with the combination of an injecting contact and charge trapping in the near surface region. Typical photoconductive gain regions are 0.2 mm across; away from these near-surface inclusions the device yields the expected diode responsivity.

Download Full-text

Magnetic Properties of Bulk Zn0.95-XMnXFe0.05O2 Prepared by Sol-Gel Method and Subsequent Hot Pressing

Advanced Materials Research ◽

10.4028/www.scientific.net/amr.268-270.356 ◽

2011 ◽

Vol 268-270 ◽

pp. 356-359 ◽

Cited By ~ 1

Author(s):

Wen Song Lin ◽

C. H. Wen ◽

Liang He

Keyword(s):

Magnetic Properties ◽

Photoelectron Spectroscopy ◽

Raw Materials ◽

Sol Gel ◽

Secondary Phase ◽

X Ray Diffraction ◽

Gel Method ◽

X Ray ◽

Sol Gel Method ◽

Doped Zno

Mn, Fe doped ZnO powders (Zn0.95-xMnxFe0.05O2, x≤0.05) were synthesized by an ameliorated sol-gel method, using Zn(CH3COO)2, Mn(CH3COO)2and FeCl2as the raw materials, with the addition of vitamin C as a kind of chemical reducer. The resulting powder was subsequently compacted under pressure of 10 MPa at the temperature of 873K in vacuum. The crystal structure and magnetic properties of Zn0.95-xMnxFe0.05O2powder and bulk samples have been investigated by X-ray diffraction (XRD) and vibrating sample magnetometer (VSM). X-ray photoelectron spectroscopy (XPS) was used to study chemical valence of manganese, iron and zinc in the samples. The x-ray diffraction (XRD) results showed that Zn0.95-xMnxFe0.05O (x≤0.05) samples were single phase with the ZnO-like wurtzite structure. No secondary phase was found in the XRD spectrum. X-ray photoelectron spectroscopy (XPS) showed that Fe and Mn existed in Zn0.95-xMnxFe0.05O2samples in Fe2+and Mn2+states. The results of VSM experiment proved the room temperature ferromagnetic properties (RTFP) of Mn, Fe co-doped ZnO samples.

Download Full-text

Influence of the Residue of Casting by Lost Wax in the Modulus of Elasticity and Porosity of Concretes

Materials Science Forum ◽

10.4028/www.scientific.net/msf.805.343 ◽

2014 ◽

Vol 805 ◽

pp. 343-349

Author(s):

Carine F. Machado ◽

Weber G. Moravia

Keyword(s):

Construction Industry ◽

Modulus Of Elasticity ◽

Chemical Characterization ◽

Microstructural Characterization ◽

Cement Matrix ◽

X Ray Diffraction ◽

X Ray ◽

Hardened State ◽

Material Powder

This work evaluated the influence of additions of the ceramic shell residue (CSR), from the industries of Lost Wax Casting, in the modulus of elasticity and porosity of concrete. The CSR was ground and underwent a physical, chemical, and microstructural characterization. It was also analyzed, the environmental risk of the residue. In the physical characterization of the residue were analyzed, the surface area, and particle size distribution. In chemical characterization, the material powder was subjected to testing of X-ray fluorescence (XRF). Microstructural characterization was performed by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The residue was utilized like addition by substitution of cement in concrete in the percentages of 10% and 15% by weight of Portland cement. It was evaluated properties of concrete in the fresh and hardened state, such as compressive strength, modulus of elasticity, absorption of water by total immersion and by capillarity. The results showed that the residue can be used in cement matrix and improve some properties of concrete. Thus, the CSR may contribute to improved sustainability and benefit the construction industry.

Download Full-text

Cerromojonite, CuPbBiSe3, from El Dragόn (Bolivia): A New Member of the Bournonite Group

Minerals ◽

10.3390/min8100420 ◽

2018 ◽

Vol 8 (10) ◽

pp. 420 ◽

Cited By ~ 2

Author(s):

Hans-Jürgen Förster ◽

Luca Bindi ◽

Günter Grundmann ◽

Chris Stanley

Keyword(s):

Incident Light ◽

Secondary Phase ◽

Hydrothermal Fluids ◽

Orthorhombic Space Group ◽

Calculated Density ◽

Metallic Luster ◽

X Ray ◽

Black Streak ◽

Mineral Aggregates ◽

The Ideal

Cerromojonite, ideally CuPbBiSe3, represents a new selenide from the El Dragόn mine, Department of Potosí, Bolivia. It either occurs as minute grains (up to 30 µm in size) in interstices of hansblockite/quijarroite intergrowths, forming an angular network-like intersertal texture, or as elongated, thin-tabular crystals (up to 200 μm long and 40 μm wide) within lath-shaped or acicular mineral aggregates (interpreted as pseudomorphs) up to 2 mm in length and 200 μm in width. It is non-fluorescent, black, and opaque, with a metallic luster and black streak. It is brittle, with an irregular fracture, and no obvious cleavage and parting. In plane-polarized incident light, cerromojonite is grey to cream-white, and weakly pleochroic, showing no internal reflections. Between crossed polarizers, cerromojonite is weakly anisotropic, with rotation tints in shades of brown and grey. Lamellar twinning on {110} is common. The reflectance values in air for the COM standard wavelengths (R1 and R2) are: 48.8 and 50.3 (470 nm), 48.2 and 51.8 (546 nm), 47.8 and 52.0 (589 nm), and 47.2 and 52.0 (650 nm). Electron-microprobe analyses yielded a mean composition of: Cu 7.91, Ag 2.35, Hg 7.42, Pb 16.39, Fe 0.04, Ni 0.02, Bi 32.61, Se 33.37, total 100.14 wt %. The empirical formula (based on 6 atoms pfu) is (Cu0.89Hg0.11)Σ = 1.00(Pb0.56Ag0.16Hg0.15 Bi0.11Fe0.01)Σ = 0.99Bi1.00Se3.01. The ideal formula is CuPbBiSe3. Cerromojonite is orthorhombic (space group Pn21m), with a = 8.202(1) Å, b = 8.741(1) Å, c = 8.029(1) Å, V = 575.7(1) Å3, Z = 4. Calculated density is 7.035 g·cm−3. The five strongest measured X-ray powder diffraction lines (d in Å (I/I0) (hkl)) are: 3.86 (25) (120), 2.783 (100) (122), 2.727 (55) (212), 2.608 (40) (310), and 1.999 (25) (004). Cerromojonite is a new member of the bournonite group, representing the Se-analogue of součekite, CuPbBi(S,Se)3. It is deposited from strongly oxidizing low-T hydrothermal fluids at a fSe2/fS2 ratio >1, both as primary and secondary phase. The new species has been approved by the IMA-CNMNC (2018-040) and is named for Cerro Mojon, the highest mountain peak closest to the El Dragón mine.

Download Full-text