scholarly journals Tribological Performance of Friction Pairs with Different Materials and Bi-Composite Surface Texture Configurations

2021 ◽  
Vol 11 (11) ◽  
pp. 4738
Author(s):  
Junjie Lu ◽  
Tianrui Wang ◽  
Xuexing Ding ◽  
Hui Song ◽  
He Li
Keyword(s):  
Friction Coefficient ◽  
Temperature Rise ◽  
Surface Texture ◽  
Adhesive Wear ◽  
Tribological Performance ◽  
Mechanical Seal ◽  
Composite Surface ◽  
Cutting Effect ◽  
Friction Performance ◽  
Internal Texture

Bi-composite surface texture configurations are proposed to study the friction performance of a mechanical seal under low speed. Three sets of comparative experiments were designed. They involved friction pairs with different pairing materials, single texture patterns, and bi-composite surface texture configurations. Tribological performances, such as friction coefficient, wear quantity, and surface topography, were measured. The research results showed that the average friction coefficient and surface temperature rise of the 3-C3 group (triangular texture in SSiC–conventional spiral groove in SSiC) were only 0.052 and 3.8 °C, respectively, which was the smallest friction coefficient and lowest temperature rise of all the test subjects. What’s more, the wear of M120D was mainly caused by the cutting effect of the texture edges, the adhesive wear of the non-textured areas, and the secondary wear caused by debris from the internal texture. It was indicated that the bi-composite patterns of spiral-triangle could produce a ‘synergistic effect’ by improving tribological performance and reaching lower friction in low-rotational-speed operation, which could provide a basis for designing a long-lasting and exceptionally reliable mechanical seal.

Experimental study on friction coefficient and temperature rise of heavy-load grease-lubricated spherical plain bearings with surface texture

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Jinlong Shen ◽  
Tong Zhang ◽  
Jimin Xu ◽  
Xiaojun LIU ◽  
Kun Liu
Keyword(s):  
Friction Coefficient ◽  
Temperature Rise ◽  
Surface Texture ◽  
Tribological Performance ◽  
Textured Surface ◽  
Textured Surfaces ◽  
Roughness Parameters ◽  
Heavy Load ◽  
Friction Coefficients ◽  
Content Type

Purpose This paper aims to improve the tribological performance of grease-lubricated spherical plain bearings (SPBs) under heavy load, dimple-type textures were prepared by laser on the outer surface of the inner ring. The influence of roughness parameters of a textured surface on reducing friction coefficient and temperature rise was also explored. Design/methodology/approach This study adopts a laser processing method to fabricate dimple-type textures. Three-dimensional roughness parameters were used to characterize the textured surfaces. The friction coefficients of five SPBs with surface texture and one original commercially available SPB without surface texture under different nominal loads were measured on a self-established test rig. The data of temperature rise were obtained by nine embedded thermal couples. Findings The results indicate that SPBs with textures generally exhibit lower friction coefficients than the original SPB without textures. The dimple depth has a significant influence on improving the tribological performance, which coincides with the analysis by surface roughness parameters. A textured surface with negative Ssk and high Vvc has the minimum temperature rise. Originality/value As it is too difficult to arrange sensors into heavy-load SPBs, there are few reports about the temperature characteristics. Through nine embedded thermal couples, the distribution of temperature rise on the inner ring of SPBs was given in this study. The positive effect of surface texture on reducing temperature rise and friction coefficient was verified, which is beneficial for the design of heavy-load SPBs.

Surface texture processing for tribological performance improvement of UHMWPE-based water-lubricated bearings

2018 ◽  
Vol 70 (7) ◽  
pp. 1341-1349 ◽  
Author(s):  
Zumin Wu ◽  
Chenxing Sheng ◽  
Zhiwei Guo ◽  
Yifei Li ◽  
Reza Malekian ◽  
...  
Keyword(s):  
Friction Coefficient ◽  
Performance Improvement ◽  
Surface Texture ◽  
Tribological Performance ◽  
Laser Interference ◽  
Content Type ◽  
Practical Applications ◽  
Contour Graph ◽  
Digital Microscope ◽  
Texture Processing

Purpose Water-lubricated bearings can significantly reduce the pollution to environment because the traditional oil lubricant is replaced by water in the bearings. The ultrahigh molecular weight polyethylene (UHMWPE) has proven to be effective and reliable for the manufacturing of water-lubricated bearings. However, limited work has been done to address the improvement of the tribological performance of the UHMWPE-based water-lubricated bearings using surface texture processing. This paper aims to investigate the effects of bar-grooved surface on the tribological performance improvement of UHMWPE-based water-lubricated bearings. Design/methodology/approach For the first time, the bar grooves were processed on the surfaces of UHMWPE-based water-lubricated bearings. The CBZ-1 friction and wear tester have been used to test the wear and friction performance of the bearing samples. The LI laser interference surface contour graph and the digital microscope have been used to measure the surface morphology of the specimens. The tribological characteristics of the tested bearings were analyzed. Findings With bar grooves added on the surfaces of the specimens, the friction coefficient of the specimens were lower than that of the specimens without surface texture processing; the wear quantity of the two kinds of specimens were almost the same; by using the LI laser interference surface contour graph and the digital microscope to measure the surface morphology of the specimens, the furrows of the specimens with bar grooves were narrower and shallower than that of the specimens without bar grooves. Practical implications The paper implicates that the surface texture processing using bar grooves can reduce the friction coefficient and prolong the service life of the water-lubricated bearings in practical applications. Originality/value This paper fulfills an identified need to provide important theoretical and experimental support to the design of water-lubricated bearings in practical applications.

Discrete element analysis of friction performance for tire-road interaction

2020 ◽  
Vol 72 (7) ◽  
pp. 977-983
Author(s):  
Jiale Lu ◽  
Baofeng Pan ◽  
Tiankai Che ◽  
Dong Sha
Keyword(s):  
Fractal Dimension ◽  
Friction Coefficient ◽  
Peer Review ◽  
Surface Texture ◽  
Discrete Element ◽  
Surface Wear ◽  
Content Type ◽  
Pavement Surface ◽  
Friction Performance ◽  
Pavement Friction

Purpose This study aims to investigate the influence of surface texture distribution in respect to the procedure of pavement surface wear on friction performance. Design/methodology/approach The Weierstrass–Mandelbrot (W-M) equation is used to appropriate pavement surface profile. Through this approximation, artificial rough profiles by combining fractal parameters and conventional statistical parameters for different macro-texture are created to simulate the procedure of pavement surface wear. Those artificial profiles are then imported into discrete element model to calculate the interaction forces and friction coefficient between rolling tire and road. Furthermore, wavelet theory is used to decompose the profiles into different scales and explore the correlation between the profiles of each scale and pavement friction. Findings The influence of tire vertical displacement (TVD) on friction coefficient is greater than fractal dimension of road surface texture. When TVD decreases, the profiles can provide higher friction, but the rolling stability of tire is poor. The optimal fractal dimension of road surface is about 1.5 when considering friction performance. The pavement friction performance improves with wavelength from 0.4 to 6.4mm and decreases with wavelength from 12.8 to 51.2mm. Originality/value Artificial fractal curves are generated and analyzed by combining W-M function with traditional parameter, which can also be used to analyze the influence of texture distribution on other pavement performance. The preliminary research provides a potential approach for the evaluation of pavement friction performance. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2019-0499/

Metal Surface Texture Research on the Influence of Friction

2019 ◽  
Vol 956 ◽  
pp. 144-153
Author(s):  
Chen Gao ◽  
Wei Wu ◽  
Xin Jun Wang ◽  
Bin Xu
Keyword(s):  
Quantitative Analysis ◽  
Friction Coefficient ◽  
Metal Surface ◽  
Temperature Rise ◽  
Surface Texture ◽  
Experimental Methods ◽  
Point Of View ◽  
Energy Point

In this paper, the influence of texture on wear and temperature rise is studied by comparing experiments at the normal temperature. Firstly, the preparation of experimental samples and the design of experimental methods are introduced. Secondly, based on the observation and analysis of two groups of experiment, the effects of surface texture on friction coefficient, temperature rise and wear are discussed respectively. The main reasons of surface texture on temperature rise are analyzed from the energy point of view, which lays a foundation for quantitative analysis of temperature rise mechanism.

Experimental study on the effect of surface texture on tribological properties of nanodiamond films under water lubrication

2021 ◽  
pp. 135065012110334
Author(s):  
Ying Yan ◽  
Xuelin Lei ◽  
Yun He
Keyword(s):  
Friction Coefficient ◽  
Wear Rate ◽  
Tribological Properties ◽  
Surface Texture ◽  
Diamond Film ◽  
Diamond Films ◽  
Nanocrystalline Diamond ◽  
Water Contact ◽  
Texture Density ◽  
Short Run

The effect of nanoscale surface texture on the frictional and wear performances of nanocrystalline diamond films under water-lubricating conditions were comparatively investigated using a reciprocating ball-on-flat tribometer. Although the untreated nanocrystalline diamond film shows a stable frictional state with an average friction coefficient of 0.26, the subsequent textured films show a beneficial effect on rapidly reducing the friction coefficient, which decreased to a stable value of 0.1. Furthermore, compared with the nanocrystalline diamond coating, the textured films showed a large decreasing rate of the corresponding ball wear rate from 4.16 × 10−3 to 1.15 × 10−3 mm3/N/m. This is due to the fact that the hydrodynamic fluid film composed of water and debris can provide a good lubrication environment, so the entire friction process has reached the state of fluid lubrication. Meanwhile, the surface texture can greatly improve the hydrophilicity of the diamond films, and as the texture density increases, the water contact angle decreases from 94.75° of the nanocrystalline diamond film to 78.5° of the textured films. The proper textured diamond film (NCD90) exhibits superior tribological properties among all tested diamond films, such as short run-in period, low coefficient of friction, and wear rate.

scholarly journals Two-scale homogenization of hydrodynamic lubrication in a mechanical seal with isotropic roughness based on the Elrod cavitation algorithm

2021 ◽  
pp. 135065012110176
Author(s):  
Yanxiang Han ◽  
Qingen Meng ◽  
Gregory de Boer
Keyword(s):  
Surface Topography ◽  
Carrying Capacity ◽  
Hydrodynamic Lubrication ◽  
Tribological Performance ◽  
Stribeck Curve ◽  
Polar Coordinate System ◽  
Load Carrying Capacity ◽  
Mechanical Seal ◽  
Macro Scale ◽  
Load Carrying

A two-scale homogenization method for modelling the hydrodynamic lubrication of mechanical seals with isotropic roughness was developed and presented the influence of surface topography coupled into the lubricating domain. A linearization approach was derived to link the effects of surface topography across disparate scales. Solutions were calculated in a polar coordinate system derived based on the Elrod cavitation algorithm and were determined using homogenization of periodic simulations describing the lubrication of a series of surface topographical features. Solutions obtained for the hydrodynamic lubrication regime showed that the two-scale homogenization approach agreed well with lubrication theory in the case without topography. Varying topography amplitude demonstrated that the presence of surface topography improved tribological performance for a mechanical seal in terms of increasing load-carrying capacity and reducing friction coefficient in the radial direction. A Stribeck curve analysis was conducted, which indicated that including surface topography led to an increase in load-carrying capacity and a reduction in friction. A study of macro-scale surface waviness showed that the micro-scale variations observed were smaller in magnitude but cannot be obtained without the two-scale method and cause significant changes in the tribological performance.

scholarly journals Analysis of High-Friction Surface Texture with Respect to Friction and Wear

Coatings ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 758
Author(s):  
Cibi Pranav ◽  
Minh-Tan Do ◽  
Yi-Chang Tsai
Keyword(s):  
Friction Coefficient ◽  
Surface Texture ◽  
Safety Concern ◽  
Future Research ◽  
Scanning System ◽  
Novel Approach ◽  
Texture Parameters ◽  
Aggregate Loss ◽  
Friction Surfaces ◽  
The Impact

High Friction Surfaces (HFS) are applied to increase friction capacity on critical roadway sections, such as horizontal curves. HFS friction deterioration on these sections is a safety concern. This study deals with characterization of the aggregate loss, one of the main failure mechanisms of HFS, using texture parameters to study its relationship with friction. Tests are conducted on selected HFS spots with different aggregate loss severity levels at the National Center for Asphalt Technology (NCAT) Test Track. Friction tests are performed using a Dynamic Friction Tester (DFT). The surface texture is measured by means of a high-resolution 3D pavement scanning system (0.025 mm vertical resolution). Texture data are processed and analyzed by means of the MountainsMap software. The correlations between the DFT friction coefficient and the texture parameters confirm the impact of change in aggregates’ characteristics (including height, shape, and material volume) on friction. A novel approach to detect the HFS friction coefficient transition based on aggregate loss, inspired by previous works on the tribology of coatings, is proposed. Using the proposed approach, preliminary outcomes show it is possible to observe the rapid friction coefficient transition, similar to observations at NCAT. Perspectives for future research are presented and discussed.

The Influence of the Addition of Ti on the Mechanical Properties of W-S-Ti Coatings

2006 ◽  
Vol 514-516 ◽  
pp. 687-691 ◽  
Author(s):  
Manuel Evaristo ◽  
Ana Nossa ◽  
Albano Cavaleiro
Keyword(s):  
Mechanical Properties ◽  
Friction Coefficient ◽  
Tribological Performance ◽  
The Self ◽  
Wear Coefficient ◽  
Gradual Loss ◽  
Order Of Magnitude ◽  
Amorphous Structures ◽  
Ti Content ◽  
Ti Films

In this work, W-S-Ti films were deposited by r.f. magnetron sputtering, using simultaneously WS2 and Ti targets. The atomic percentage of Ti in the coating was varied from 0 at.% up to 28 at.%. No significant variations in the S/W ratio with the increase of Ti content were observed. The increasing Ti contents in the films led to a gradual loss of crystallinity. Coatings with contents greater than ≈ 16 at.% only presents a broad peak characteristic of amorphous structures. Alloying the films with Ti led to significant improvements in the hardness (from 0.3 to 8.9 GPa). Also, the adhesive critical load continuously grew with the increase of the Ti content in the films. The wear coefficient of the films dropped more than one order of magnitude with the increase of Ti content whereas the friction coefficient was kept fairly constant with just a small increase in relation to single W-S film. In conclusion, to have a good tribological performance, the addition of Ti to the films should be balanced in order that the increase of the mechanical properties does not lead to severe loss of the self-lubricant properties.

Tribological performance of self-lubricated polyamide6/boric oxide composites after water conditioning

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Kawaljit Singh Randhawa ◽  
Ashwin Patel
Keyword(s):  
Friction Coefficient ◽  
Abrasion Resistance ◽  
Tribological Performance ◽  
Boric Oxide ◽  
Resistance Testing ◽  
Tribological Behaviour ◽  
Content Type ◽  
Wear Rates ◽  
Water Conditioning ◽  
Oxide Composites

Purpose This paper aims to investigate the tribological performance, i.e. abrasion resistance, friction coefficient and wear rates, of self-lubricated water conditioned polyamide6/boric oxide composites. Design/methodology/approach Polyamide6 and polyamide6/boric oxide self-lubricated composites were immersed in water for 15 days to analyze the effect of water conditioning on friction, wear and abrasion resistance. Tribological testing on pin-on-disc tribometer and abrasion resistance testing on TABER abrader were performed to see the friction coefficient and wear rates of materials. The scanning electron microscopy (SEM) characterizations were performed to analyze the wear tracks. Findings Tribological testing results revealed the loss in abrasive resistance, but there was an improvement in frictional coefficient and wear rates with steel after water absorption. The SEM images clearly show less depth of wear tracks in water-conditioned materials than dry ones. Water conditioning was found supportive in the formation of smooth lubricating transfer film on steel disc during the tribological testing. Originality/value The tribological behaviour of polymer composites is different in dry and in high humidity or water conditions. Experiments were performed to investigate B2O3 solid lubricant filler effectiveness on tribological behaviour of water-conditioned polyamide composites. Bonding between polyamide6 and water molecules plus the formation of orthoboric acid was found advantageous in decreasing the friction coefficient and wear rates of composites.

The Influence of Surface Texture on Abrasive Wear

2019 ◽  
Vol 823 ◽  
pp. 33-40 ◽  
Author(s):  
Yu Tong Hu ◽  
Yong Yong He ◽  
Wei Wang
Keyword(s):  
Friction Coefficient ◽  
Femtosecond Laser ◽  
Abrasive Wear ◽  
White Light ◽  
Surface Texture ◽  
Friction Surface ◽  
Surface Texturing ◽  
Experimental Results ◽  
The Relationship ◽  
Main Factor

Friction happens everywhere. Abrasives generated in tribological process will result in secondary wear. Abrasive wear is a kind of rather common but harmful wear, which is the main reason for the damage of fifty-percent mechanical components by friction. Surface texturing is an effective method to improve the tribological and lubricating performance of tribo-pairs. In this paper, with different-size diamond particles added into the lubricant and a surface of the tribo-pairs textured by different parameters (diameter and depth) with femtosecond laser, the relationship between the surface texture and the abrasive wear was researched, and the influence of the texture on the abrasive wear was analyzed. The friction experiments were carried out on UMT3. The microstructures were tested and analyzed by SEM, microscope and White Light Interferometer respectively. The experimental results showed that the size of the surface texture, compared with that of abrasives, is the main factor which determines the friction coefficient. As the size of the surface texture is much bigger than that of the abrasives, the texture can accommodate the abrasives efficiently, and thus the friction coefficient is reduced efficiently.

Sign in / Sign up

Export Citation Format

Share Document