scholarly journals Effects of Heat Treatment on the Microstructure and Hardness of A356 (AlSi7Mg0.3) Manufactured by Vertical Centrifugal Casting

2021 ◽  
Vol 11 (23) ◽  
pp. 11572
Author(s):  
Wonho Kim ◽  
Kyungsu Jang ◽  
Changwook Ji ◽  
Eunkyung Lee
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Intermetallic Compounds ◽  
Centrifugal Casting ◽  
A356 Alloy ◽  
Brake Disk ◽  
Centrifugally Cast ◽  
Average Hardness ◽  
Heat Treated

The A356 alloy has been widely used in automotive components, such as wheels and brake disks, because it is an excellent lightweight material with high corrosion resistance and good mechanical properties. Recently, to reduce the weight of brake disks, the Fe-A356 hybrid brake disk has been suggested. Because brake disk quality is directly related to driving safety, the T4/T6 heat treatment of centrifugally cast A356 alloys were performed to enhance the mechanical properties and reduce micro-segregation. The solid-solution heat treatment followed by annealing caused the formation of Mg-rich intermetallic compounds on the grain boundaries of the Al matrix, decreasing the average hardness of the alloys by 13 HV. In contrast, the solid solution followed by water quenching (T4) reduced the area fractions of the intermetallic compounds and increased the average hardness by 11 HV. The T6 heat-treated A356 alloys, which were influenced by the formation of the Guinier–Preston zone exhibited a relatively higher average hardness, by 18 HV, compared to T4 heat-treated A356 alloys.

scholarly journals Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Metals ◽  
2021 ◽  
Vol 12 (1) ◽  
pp. 71
Author(s):  
Ho-Jung Kang ◽  
Jin-Young Park ◽  
Yoon-Suk Choi ◽  
Dae-Hyun Cho
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Artificial Aging ◽  
Solution Treatment ◽  
Mg Alloys ◽  
Needle Type ◽  
Heat Treated ◽  
Die Cast ◽  
Eutectic Si

Heat treatment is widely used to improve the properties of Al–Si–Mg alloys and its outcomes are influenced by the parameters applied during the treatment. This study describes the effect of the solution and artificial aging treatments on the microstructure and mechanical properties of die-cast Al–Si–Mg alloys. The microstructure of the as-cast Al–Si–Mg alloy was mainly composed of α-Al, complex needle-type eutectic Si particles, Mg2Si, and α-AlFeMn. The complex needle-type eutectic Si particles disintegrated into spheroidal morphologies, while the Mg2Si was dissolved due to the solid solution treatment. The maximum yield strength (YS) and ultimate tensile strength (UTS) values were 126.06 and 245.90 MPa at 520 °C after 90 min of solution heat treatment, respectively. Although the YS and UTS values of the Al–Si–Mg alloys reduced due to the solution treatment, the elongation (EL) of the solid solution heat-treated Al–Si–Mg alloys was improved in comparison to that of the as-cast Al–Si–Mg alloy. The maximum YS and UTS of 239.50 and 290.93 MPa were obtained after performing artificial aging at 180 °C for 180 min, respectively. However, the EL of the aging heat-treated alloy was reduced by a minimal value.

scholarly journals Influence of Post Weld Heat Treatment on the Grain Size, and Mechanical Properties of the Alloy-800H Rotary Friction Weld Joints

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4366
Author(s):  
Saqib Anwar ◽  
Ateekh Ur Rehman ◽  
Yusuf Usmani ◽  
Ali M. Al-Samhan
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Heat Affected Zone ◽  
Tensile Testing ◽  
Weld Zone ◽  
Alloy 800H ◽  
Weld Joints ◽  
Heat Treated ◽  
Friction Weld

This study evaluated the microstructure, grain size, and mechanical properties of the alloy 800H rotary friction welds in as-welded and post-weld heat-treated conditions. The standards for the alloy 800H not only specify the composition and mechanical properties but also the minimum grain sizes. This is because these alloys are mostly used in creep resisting applications. The dynamic recrystallization of the highly strained and plasticized material during friction welding resulted in the fine grain structure (20 ± 2 µm) in the weld zone. However, a small increase in grain size was observed in the heat-affected zone of the weldment with a slight decrease in hardness compared to the base metal. Post-weld solution heat treatment (PWHT) of the friction weld joints increased the grain size (42 ± 4 µm) in the weld zone. Both as-welded and post-weld solution heat-treated friction weld joints failed in the heat-affected zone during the room temperature tensile testing and showed a lower yield strength and ultimate tensile strength than the base metal. A fracture analysis of the failed tensile samples revealed ductile fracture features. However, in high-temperature tensile testing, post-weld solution heat-treated joints exhibited superior elongation and strength compared to the as-welded joints due to the increase in the grain size of the weld metal. It was demonstrated in this study that the minimum grain size requirement of the alloy 800H friction weld joints could be successfully met by PWHT with improved strength and elongation, especially at high temperatures.

Investigation of Functionally Graded Aluminium A356 Alloy and A356-10%SiCp Composite for Hydro Turbine Bucket Application

2016 ◽  
Vol 26 ◽  
pp. 30-46 ◽  
Author(s):  
Williams S. Ebhota ◽  
Akhil S. Karun ◽  
Freddie L. Inambao
Keyword(s):  
Heat Treatment ◽  
Tensile Stress ◽  
Centrifugal Casting ◽  
A356 Alloy ◽  
Casting Process ◽  
Ultimate Tensile Stress ◽  
Functionally Graded ◽  
Cnc Machining ◽  
Mould Material ◽  
Turbine Bucket

The study investigates the application of centrifugal casting process in the production of a complex shape component, Pelton turbine bucket. The bucket materials examined were functionally graded aluminium A356 alloy and A356-10%SiCp composite. A permanent mould for the casting of the bucket was designed with a Solidworks software and fabricated by the combination of CNC machining and welding. Oil hardening non-shrinking die steel (OHNS) was chosen for the mould material. The OHNS was heat treated and a hardness of 432 BHN was obtained. The mould was put into use, the buckets of A356 Alloy and A356-10%SiCp composite were cast, cut and machined into specimens. Some of the specimens were given T6 heat treatment and the specimens were prepared according to the designed investigations. The micrographs of A356-10%SiCp composite shows more concentration of SiCp particles at the inner periphery of the bucket. The maximum hardness of As-Cast A356 and A356-10%SiCp composite were 60 BRN and 95BRN respectively, recorded at the inner periphery of the bucket. And these values appreciated to 98BRN and 122BRN for A356 alloy and A356-10%SiCp composite respectively after heat treatment. The prediction curves of the ultimate tensile stress and yield tensile stress show the same trend as the hardness curves.

Structure and Hardness of Cryorolled and Heat-Treated 2xxx Aluminum Alloy

2010 ◽  
Vol 667-669 ◽  
pp. 925-930
Author(s):  
S.V. Krymskiy ◽  
Elena Avtokratova ◽  
M.V. Markushev ◽  
Maxim Yu. Murashkin ◽  
O.S. Sitdikov
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Severe Plastic Deformation ◽  
Coarse Grained ◽  
Aging Response ◽  
Heat Treated ◽  
Aluminum Solid Solution ◽  
A Cell

The effects of severe plastic deformation (SPD) by isothermal rolling at the temperature of liquid nitrogen combined with prior- and post-SPD heat treatment, on microstructure and hardness of Al-4.4%Cu-1.4%Mg-0.7%Mn (D16) alloy were investigated. It was found no nanostructuring even after straining to 75%. Сryodeformation leads to microshear banding and processing the high-density dislocation substructures with a cell size of ~ 100-200 nm. Such a structure remains almost stable under 1 hr annealing up to 200oC and with further temperature increase initially transforms to bimodal with a small fraction of nanograins and then to uniform coarse grained one. It is found the change in the alloy post–SPD aging response leading to more active decomposition of the preliminary supersaturated aluminum solid solution, and to the alloy extra hardening under aging with shorter times and at lower temperatures compared to T6 temper.

Application of Tailored Heat Treated Blanks under Quasi Series Conditions

2007 ◽  
Vol 344 ◽  
pp. 383-390 ◽  
Author(s):  
Marion Merklein ◽  
Uwe Vogt
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Local Heat ◽  
Strength Distribution ◽  
Process Window ◽  
Short Term ◽  
Forming Process ◽  
Heat Treated ◽  
Set Up ◽  
The Impact

Tailored Heat Treated Blanks (THTB) are blanks that exhibit locally different strength specifically optimized for the succeeding forming process. The strength distribution is set by a local, short-term heat treatment modifying the mechanical properties of the material. Hence, THTB allow enhancing forming limits significantly leading to shorter and more robust manufacture process chains. In order to qualify the use of THTB under quasi series conditions, the interdependencies of the blank’s local heat treatment and the entire process chain of the car body manufacture have to be analyzed. In this respect, the impact of a short-term heat treatment on the mechanical properties of AA6181PX, a commonly used aluminum alloy in today’s car bodies, was studied. Also the influence of a short-term heat treatment on the coil lubricant, usually already applied by the material supplier, was given a closer look. Based on these experiments process restrictions for the application of THTB in an industrial automotive environment were derived and a process window for the THTB design was set up. In conclusion, strategies were defined how to enhance the found process boundaries leading to a more robust process window.

scholarly journals Effects of Different Solid Solution Temperatures on Microstructure and Mechanical Properties of the AA7075 Alloy After T6 Heat Treatment

2019 ◽  
Vol 38 (2019) ◽  
pp. 892-896 ◽  
Author(s):  
Süleyman Tekeli ◽  
Ijlal Simsek ◽  
Dogan Simsek ◽  
Dursun Ozyurek
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid Solution ◽  
Tensile Strength ◽  
Tensile Tests ◽  
Solution Temperature ◽  
T6 Heat Treatment ◽  
Microstructure And Mechanical Properties ◽  
Different Temperatures

AbstractIn this study, the effect of solid solution temperature on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment was investigated. Following solid solution at five different temperatures for 2 hours, the AA7075 alloy was quenched and then artificially aged at 120∘C for 24 hours. Hardness measurements, microstructure examinations (SEM+EDS, XRD) and tensile tests were carried out for the alloys. The results showed that the increased solid solution temperature led to formation of precipitates in the microstructures and thus caused higher hardness and tensile strength.

Effect of heat treatment on mechanical properties of 3D printed polylactic acid parts

2021 ◽  
Vol 63 (1) ◽  
pp. 73-78
Author(s):  
Pulkin Gupta ◽  
Sudha Kumari ◽  
Abhishek Gupta ◽  
Ankit Kumar Sinha ◽  
Prashant Jindal
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Polylactic Acid ◽  
Recrystallization Temperature ◽  
Fused Deposition Modelling ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Maximum Decrease ◽  
3D Printed

Abstract Fused deposition modelling (FDM) is a layer-by-layer manufacturing process type of 3D-printing (3DP). Significant variation in the mechanical properties of 3D printed specimens is observed because of varied process parameters and interfacial bonding between consecutive layers. This study investigates the influence of heat treatment on the mechanical strength of FDM 3D printed Polylactic acid (PLA) parts with constant 3DP parameters and ambient conditions. To meet the objectives, 7 sets, each containing 5 dog-bone shaped samples, were fabricated from commercially available PLA filament. Each set was subjected to heat treatment at a particular temperature for 1 h and cooled in the furnace itself, while one set was left un-treated. The temperature for heat treatment (Th) varied from 30 °C to 130 °C with increments of 10 °C. The heat-treated samples were characterized under tensile loading of 400 N and mechanical properties like Young’s modulus (E), Strain % ( ε ) and Stiffness (k) were evaluated. On comparing the mechanical properties of heat-treated samples to un-treated samples, significant improvements were observed. Heat treatment also altered the geometries of the samples. Mechanical properties improved by 4.88 % to 10.26 % with the maximum being at Th of 110 °C and below recrystallization temperature (Tr) of 65 °C. Deformations also decreased significantly at higher temperatures above 100 °C, by a maximum of 36.06 %. The dimensions of samples showed a maximum decrease of 1.08 % in Tr range and a maximum decrease of 0.31 % in weight at the same temperature. This study aims to benefit the society by establishing suitable Th to recover the lost strength in PLA based FDM 3D printed parts.

Influence of Heat Treatment on Microstrudture and Mechanical Properties of AZ31B Magnesium Alloy Prepared by Solid-State Recycling

2012 ◽  
Vol 271-272 ◽  
pp. 17-20
Author(s):  
Shu Yan Wu ◽  
Ze Sheng Ji ◽  
Chun Ying Tian ◽  
Ming Zhong Wu
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Solid State ◽  
Magnesium Alloy ◽  
Static Recrystallization ◽  
Annealing Treatment ◽  
Az31b Magnesium Alloy ◽  
Heat Treated ◽  
Elongation To Failure ◽  
Strength And Ductility

This work is to study the influence of heat treatment on microstrudture and mechanical properties of AZ31B magnesium alloy prepared by solid -state recycling. AZ31B magnesium alloy chips were recycled by hot extruding. Three different heat treatments were conducted for recycled alloy. Mechanical properties and microstructure of the recycled specimen and heat treated specimen were investigated. 300°C×2h annealing specimen exhibits finer grain due to static recrystallization, and microstructure of 400°C×2h annealing specimen becomes more coarse. 300°C×2h annealing treatment improves obviously strength and ductility of recycled alloy. Ultimate tensile strength of alloy decreases and elongation to failure increases after 400°C×2h annealing. Grain size, dislocation density and bonding of chips have an effect on the elongation of recycled materials. 190°C×8h ageing has no influence on microstructure and mechanical properties of recycled alloy.

scholarly journals Electron Beam Melting of Ti-6Al-4V Lattice Structures; Correlation between Post Heat Treatment and Mechanical Properties

2021 ◽  
Author(s):  
Giuseppe Del Guercio ◽  
Manuela Galati ◽  
Abdollah Saboori
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Computer Aided Design ◽  
Mechanical Performance ◽  
Industrial Applications ◽  
Heat Treatments ◽  
Layer By Layer ◽  
Lattice Structures ◽  
Heat Treated ◽  
Aided Design

Abstract Additive Manufacturing processes are considered advanced manufacturing methods. It would be possible to produce complex shape components from a Computer-Aided Design model in a layer-by-layer manner. Lattice structures as one of the complex geometries could attract lots of attention for both medical and industrial applications. In these structures, besides cell size and cell type, the microstructure of lattice structures can play a key role in these structures' mechanical performance. On the other hand, heat treatment has a significant influence on the mechanical properties of the material. Therefore, in this work, the effect of the heat treatments on the microstructure and mechanical behaviour of Ti-6Al-4V lattice structures manufactured by EBM was analyzed. The main mechanical properties were compared with the Ashby and Gibson model. It is very interesting to notice that a more homogeneous failure mode was found for the heat-treated samples. The structures' relative density was the main factor influencing their mechanical performance of the heat-treated samples. It is also found that the heat treatments were able to preserve the stiffness and the compressive strength of the lattice structures. Besides, an increment of both the elongation at failure and the absorbed energy was obtained after the heat treatments. Microstructure analysis of the heat-treated samples confirms the increment of ductility of the heat-treated samples with respect to the as-built one.

scholarly journals PROPERTIES OF PARTICLEBOARD PANELS MADE OF SUGARCANE PARTICLES WITH AND WITHOUT HEAT TREATMENT

2019 ◽  
Vol 43 (5) ◽  
Author(s):  
Emerson Gomes Milagres ◽  
Raiana Augusta Grandal Savino Barbosa ◽  
Karine Fernandes Caiafa ◽  
Gabriel Soares Lopes Gomes ◽  
Tatiana Aurora Condezo Castro ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Sugarcane Bagasse ◽  
Linear Expansion ◽  
Basic Density ◽  
Water Vapor Adsorption ◽  
Thickness Swelling ◽  
Specific Mass ◽  
Heat Treated ◽  
Significant Difference

ABSTRACT The objective of this work was to determine the properties of particleboard panels made of “in natura” sugarcane bagasse particles, heated at 250 °C for 5 minutes. Various particle proportions were utilized to produce the panels and their properties were compared with that of a panel made of Pinus sp. The panels were produced with 8% tannin formaldehyde adhesive, and 0.5% paraffin emulsion, being pressed at 32 kgf.cm-2 for 10 minutes at 180 ° C. It was determined the basic density of the “in natura” and heat-treated particles, their chemical composition, as well as the compression ratio necessary to obtain panels with density equal to 0.75 g.cm-3. The basic density of the panels, hygroscopic equilibrium humidity, thickness swelling, linear expansion, water vapor adsorption, modulus of elasticity and rupture, perpendicular traction, screw pullout, and Janka hardness were determined. The basic densities of Pinus particles and sugarcane bagasse without and with heat treatment were 0.46, 0.27 and 0.30 g.cm-3, respectively. The average specific mass of the panels was 0.74 g.cm-3 with no significant difference between them. Generally, panels made of sugarcane particles were less hygroscopic and dimensionally more stable than panels made of Pinus particles. However, the perpendicular tensile strength, screw pullout and Janka hardness of these panels were higher than for the Pinus panels. The heat treatment of sugarcane bagasse particles resulted in better mechanical properties of perpendicular traction and Janka hardness. In general, the panels are within the limits set by ANSI A208.1. It is therefore possible to replace panels made of Pinus particles for the ones made of sugarcane bagasse, provided that at least 25% of the particles are heat treated for 5 minutes at 250 ° C.

Sign in / Sign up

Export Citation Format

Share Document