scholarly journals A Research on the Macroscopic and Mesoscopic Parameters of Concrete Based on an Experimental Design Method

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1627
Author(s):  
Hui Su ◽  
Hongliang Li ◽  
Baowen Hu ◽  
Jiaqi Yang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Experimental Design ◽  
Significant Influence ◽  
Interfacial Transition Zone ◽  
The Other ◽  
Stiffness Ratio ◽  
Response Surface Design ◽  
Surface Design

Concrete is a composite material that has complex mechanical properties. The mechanical properties of each of its components are different at the mesoscopic scale. Studying the relationship between the macroscopic and mesoscopic parameters of concrete can help better understand its mechanical properties at these levels. When using the discrete element method to model the macro-mesoscopic parameters of concrete, their calibration is the first challenge. This paper proposes a numerical model of concrete using the particle discrete element software particle flow code (PFC). The mesoscopic parameters required by the model need to be set within a certain range for an orthogonal experimental design. We used the proposed model to perform numerical simulations as well as response surface design and analysis. This involved fitting a set of mapping relationships between the macro–micro parameters of concrete. An optimization model was established in the MATLAB environment. The program used to calibrate the mesoscopic parameters of concrete was written using the genetic algorithm, and its macro-micro parameters were inverted. The following three conclusions can be drawn from the orthogonal test: First, the tensile strength and shear strength of the parallel bond between the particles of mortar had a significant influence on the peak compressive strength of concrete, whereas the influence of the other parameters was not significant. Second, the elastic modulus of the parallel bonding between particles of mortar, their stiffness ratio and friction coefficient, and the elastic modulus and stiffness ratio of contact bonding in the interfacial transition zone had a significant influence on the elastic modulus, whereas the influence of the other parameters was not significant. Third, the elastic modulus, stiffness ratio, and friction coefficient of the particles of mortar as well as the ratio of the contact adhesive stiffness in their interfacial transition zone had a significant influence on Poisson’s ratio, whereas the influence of the other parameters was not significant. The fitting effect of the response surface design was good.

Experimental Investigation into the Influences of Weathering on the Mechanical Properties of Sedimentary Rocks

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Xiaoshuang Li ◽  
Yingchun Li ◽  
Saisai Wu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Uniaxial Compression ◽  
Sedimentary Rocks ◽  
Uniaxial Tensile ◽  
Mechanical Parameters ◽  
Uniaxial Tensile Strength ◽  
Weathering Grades

The time-dependent behaviors of the sedimentary rocks which refer to the altering of the mechanical and deformable properties of rock elements in the long-term period are of increasing importance in the investigation of the failure mechanism of the rock strata in underground coal mines. In order to obtain the accurate and reliable mechanical parameters of the sedimentary rocks at different weathering grades, the extensive experimental programs including the Brazilian splitting test, uniaxial compression tests, and direct shear tests have been carried out on the specimens that exposed to the nature environments at different durations. The correlation between the weathering grades and mechanical parameters including uniaxial tensile strength, uniaxial compression strength, elastic modulus, Poisson’s ratio, cohesion, and friction coefficient was proposed. The obtained results suggested that uniaxial tensile strength, uniaxial compressive strength, elastic modulus, and cohesion dramatically decreased with increasing weathering time, characterized as the negative exponential relationship in general. The influences of various weathering grades on fracture behavior of the rock specimens were discussed. The cumulative damage of the rock by the weathering time decreased the friction coefficient of the specimens which led to the initiation and propagation of microcrack within the rock at lower stress conditions. The obtained results improved the understanding of the roles of weathering on the mechanical properties of sedimentary rocks, which is helpful in the design of the underground geotechnical structures.

scholarly journals Reduction of the Coefficient of Friction of Steel-Steel Tribological Contacts by Novel Graphene-Deep Eutectic Solvents (DESs) Lubricants

Lubricants ◽  
2019 ◽  
Vol 7 (4) ◽  
pp. 37 ◽  
Author(s):  
Ignacio Garcia ◽  
Silvia Guerra ◽  
Juan de Damborenea ◽  
Ana Conde
Keyword(s):  
Mechanical Properties ◽  
Ionic Liquids ◽  
Friction Coefficient ◽  
Wear Rate ◽  
Adhesive Wear ◽  
Choline Chloride ◽  
Deep Eutectic Solvents ◽  
The Other ◽  
Graphene Flakes ◽  
The Coefficient Of Friction

Deep eutectic ionic liquids (DES) possess similar properties to conventional ionic liquids (ILs). However, ILs cannot be considered as environmentally friendly compounds due to both its processing and synthesis, which could have significant polluting effects. On the contrary, deep eutectic solvents (DESs) can be biodegradable, non-toxic, and have a lower price than most ILs, making them potentially useful in a wide variety of advanced technological applications, such as tribology. On the other hand, graphene has recently been proposed as an extremely promising lubricant due to its combination of mechanical properties and chemical stability as well as its “green” character. In the present paper, graphene flakes (≈250 nm) have been used as an additive to DES composed of choline chloride (ChCl)-urea, ChCl-ethylene glycol, and ChCl-malic acid. According to the results, the addition of 1 wt% graphene reduces friction coefficient (COF) and, notably, prevents adhesive wear, reducing wear rate on steel-steel sliding contacts.

Effect of Microstructure on Mechanical Properties and Wear Characteristics of Cemented Tungsten Carbides

2009 ◽  
Vol 76-78 ◽  
pp. 609-612 ◽  
Author(s):  
H.Q. Sun ◽  
Rudy Irwan ◽  
Han Huang ◽  
Gwidon W. Stachowiak
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elastic Modulus ◽  
Friction Coefficient ◽  
Tungsten Carbide ◽  
Removal Rate ◽  
Tungsten Carbides ◽  
Removal Rates ◽  
Wear Characteristics ◽  
Effect Of Microstructure

The effect of microstructure of cemented tungsten carbide materials on their mechanical properties and wear characteristics was investigated using nanoindentation and nanoscratch methods. The results indicated that the variation in grain size insignificantly affected the hardness, elastic modulus and friction coefficient of the work materials, but considerably influenced their removal rates. The carbide with coarser grains exhibited a much higher removal rate was obtained during scratching.

Some Physical and Mechanical Properties of Garlic

2007 ◽  
Vol 3 (6) ◽  
Author(s):  
Adel H. Bahnasawy
Keyword(s):  
Mechanical Properties ◽  
Friction Coefficient ◽  
Contact Surface ◽  
Chemical Properties ◽  
Physical And Mechanical Properties ◽  
Friction Angle ◽  
Arithmetic Mean ◽  
The Other ◽  
Cross Sectional ◽  
Length Width

The physical parameter results showed that the garlic geometric and arithmetic mean diameters ranged from 2.53 to 4.93, and 2.53 to 5.02 cm, respectively according to the bulb size categories. The cloves' length, width and thickness were 1.92 to 2.91, 0.78 to 1.32, and 0.69 to 0.99 cm, respectively. The surface and cross-sectional of areas ranged from 53.31 to 136.4 and 29.1 to 128.4 cm2, respectively. The number of cloves ranged from 18 to 51/bulb according to the bulbs size categories. Bulk density, repose angle and coefficient of contact surface values ranged from 892 to 1007 kg/m3, 41.52 to 45.04º, and 0.91 to 1.12, respectively, according to the bulb size categories.The chemical properties showed that the emptying (friction) angle ranged from 23.25 to 28.82º, where small bulbs recorded the highest values on the concrete surfaces, while the lowest values were recorded by the large bulbs on the iron surfaces. The friction coefficient decreased with increasing bulb size, where it was the highest (0.8) for the small bulbs on the concrete surfaces; on the other hand, the lowest values (0.36) were recorded for the large bulbs on the iron surfaces. The crushing load of the cloves ranged from 55.6 to 155.0 N, depending on the bulb size. The force required for loosening the cloves from the bulb ranged from 110 to 272 and 101 to 320 N on the horizontal and vertical positions of the bulbs.

scholarly journals Study on the Influence of the Grind Percentage Over the Surface Hardness and Modulus of Elasticity of Parts Made of ABS, P6.6 and POM through Nanoindentation

2019 ◽  
Vol 56 (1) ◽  
pp. 65-70
Author(s):  
Gheorghe Radu Emil Maries ◽  
Constantin Bungau ◽  
Dan Chira ◽  
Traian Costea ◽  
Danut-Eugeniu Mosteanu
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Surface Hardness ◽  
Acrylonitrile Butadiene Styrene ◽  
The Other ◽  
Indentation Hardness ◽  
Indentation Modulus ◽  
Maximum Hardness ◽  
New Material ◽  
Butadiene Styrene

This paper analyzes the indentation hardness and the indentation elastic modulus variation depending on the variation of the grind percentage of polymer, when the other factors that can influence the injection molding remain unchanged. The analyzed polymers were: acrylonitrile butadiene styrene ABS MAGNUM 3453, polyamide PA 6.6 TECHNYL AR218V30 Blak and polyoxymethylene POM EUROTAL C9 NAT. The samples that were studied had different compositions in new and grinding material. The G-Series Basic Hardness Modulus at a Depth method was used. The increase of the grind percentage of ABS (from 0 to 100 %) leads to insignificant changes in the indentation hardness, indentation modulus, and maximum force applied to samples of tested material. The maximum hardness (0.137 GPa) of PA 6.6 is recorded in the case of the sample with 80% grind content, and the maximum hardness of POM is recorded as well in the case of the sample with 80% grind content, as being 0.215 GPa. The variation of the grind content in the analyzed samples determines changes in the evaluated parameters, depending on the type of polymer. Combining the new material with grind in proportions experimentally established for each techno polymer leads to changes in their mechanical properties.

scholarly journals FeZrN Films: Magnetic and Mechanical Properties Relative to the Phase-Structural State

Materials ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 137
Author(s):  
Elena N. Sheftel ◽  
Valentin A. Tedzhetov ◽  
Eugene V. Harin ◽  
Philipp V. Kiryukhantsev-Korneev ◽  
Galina S. Usmanova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Magnetic Properties ◽  
Elastic Modulus ◽  
Elastic Recovery ◽  
The Other ◽  
Magnetron Deposition ◽  
Glass Substrates ◽  
Saturation Induction ◽  
Low Elastic Modulus ◽  
Chemical And Phase Compositions

The paper presents results of investigation of Fe65.3–100Zr34.7–0N7.5–0 films prepared by dc magnetron deposition on glass substrates and subsequent 1-hour annealing at temperatures of 300–600 °C. The influence of the chemical and phase compositions and structure of the films, which were studied by TEM, SEM, XRD, and GDOES, on their mechanical properties determined by nanoindentation and static magnetic properties measured by VSM method is analyzed. The studied films exhibit the hardness within a range of 14–21 GPa, low elastic modulus (the value can reach 156 Gpa), and an elastic recovery of 55–83%. It was shown that the films are strong ferromagnets with the high saturation induction Bs (up to 2.1 T) and low coercive field Hc (as low as 40 A/m). The correlations between the magnetic and mechanical properties, on one hand, and the chemical composition of the films, their phase, and structural states as well, on the other hand, are discussed.

scholarly journals Optimization of Banana Peels Hydrolysis for the Production of Bioethanol: Response Surface Methodology

2015 ◽  
Vol 48 ◽  
pp. 53-60
Author(s):  
Mebrahtom Gebresemati ◽  
Alula Gebregergs
Keyword(s):  
Response Surface ◽  
Raw Materials ◽  
Optimum Combination ◽  
The Other ◽  
Fermentable Sugar ◽  
Response Surface Design ◽  
Benzyl Penicillin ◽  
Surface Design ◽  
Developing Cities ◽  
Experimental Runs

Energy consumption has increased steadily over the last four decades as the population has grown and more countries have become industrialized. On the other hand waste disposal has become the major concern of developing cities. Many countries such as Ethiopia have abundant raw materials for biofuels, yet these have not been explored. This study was designed to utilize banana peels for the production of bioethanol using the yeast Saccharomyces cerevisiae. The effects of factors in hydrolysis (the effect of hydrolysis parameters) were investigated and the optimum combination factor was carried out with response surface design. The parameters were varied over 3 levels and 17 experimental runs were conducted to produce fermentable sugar. The optimum results were obtained at 1.50 % v/v acid concentration, 91.02 °C temperature and 21.66 min retention time. At this optimum condition, fermentation with and without benzyl penicillin was performed to determine its effect on bioethanol.

scholarly journals Polymerization Behavior and Mechanical Properties of High-Viscosity Bulk Fill and Low Shrinkage Resin Composites

2017 ◽  
Vol 42 (6) ◽  
pp. E177-E187 ◽  
Author(s):  
S Shibasaki ◽  
T Takamizawa ◽  
K Nojiri ◽  
A Imai ◽  
A Tsujimoto ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Resin Composite ◽  
High Viscosity ◽  
The Other ◽  
Light Irradiation ◽  
Volumetric Shrinkage ◽  
Resin Composites ◽  
Polymerization Shrinkage

SUMMARY The present study determined the mechanical properties and volumetric polymerization shrinkage of different categories of resin composite. Three high viscosity bulk fill resin composites were tested: Tetric EvoCeram Bulk Fill (TB, Ivoclar Vivadent), Filtek Bulk Fill posterior restorative (FB, 3M ESPE), and Sonic Fill (SF, Kerr Corp). Two low-shrinkage resin composites, Kalore (KL, GC Corp) and Filtek LS Posterior (LS, 3M ESPE), were used. Three conventional resin composites, Herculite Ultra (HU, Kerr Corp), Estelite ∑ Quick (EQ, Tokuyama Dental), and Filtek Supreme Ultra (SU, 3M ESPE), were used as comparison materials. Following ISO Specification 4049, six specimens for each resin composite were used to determine flexural strength, elastic modulus, and resilience. Volumetric polymerization shrinkage was determined using a water-filled dilatometer. Data were evaluated using analysis of variance followed by Tukey's honestly significant difference test (α=0.05). The flexural strength of the resin composites ranged from 115.4 to 148.1 MPa, the elastic modulus ranged from 5.6 to 13.4 GPa, and the resilience ranged from 0.70 to 1.0 MJ/m3. There were significant differences in flexural properties between the materials but no clear outliers. Volumetric changes as a function of time over a duration of 180 seconds depended on the type of resin composite. However, for all the resin composites, apart from LS, volumetric shrinkage began soon after the start of light irradiation, and a rapid decrease in volume during light irradiation followed by a slower decrease was observed. The low shrinkage resin composites KL and LS showed significantly lower volumetric shrinkage than the other tested materials at the measuring point of 180 seconds. In contrast, the three bulk fill resin composites showed higher volumetric change than the other resin composites. The findings from this study provide clinicians with valuable information regarding the mechanical properties and polymerization kinetics of these categories of current resin composite.

Synthesis and Characterisation of New Superelastic and Low Elastic Modulus Ti-Nb-X Alloys for Biomedical Application

2011 ◽  
Vol 409 ◽  
pp. 170-174
Author(s):  
A. Ramarolahy ◽  
Philippe Castany ◽  
Thierry Gloriant ◽  
Frédéric Prima ◽  
P. Laheurte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Shape Memory ◽  
Biomedical Application ◽  
The Other ◽  
Alloying Element ◽  
Low Elastic Modulus ◽  
Superelastic Behavior ◽  
Good Biocompatibility

Ti-Nb based alloys are well known to their good mechanical properties, shape memory effect, superelasticity, as well as good biocompatibility. The Ti-24Nb (at%) binary alloy presents a shape memory behavior and low elastic modulus. Our study is focused on the improvement of their mechanical properties by adding a third alloying element (oxygen, nitrogen or silicon). Addition of 0.5 at% of N or O modifies drastically the mechanical behavior of Ti-24Nb alloy that exhibits superelastic behavior instead of shape memory one. On the other hand, addition of 0.5 at% of Si increased yield strength of the Ti-24Nb shape memory alloy.

scholarly journals PVA/Polysaccharides Blended Films: Mechanical Properties

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Fábio E. F. Silva ◽  
Maria Carolina B. Di-Medeiros ◽  
Karla A. Batista ◽  
Kátia F. Fernandes
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Mechanical Characteristics ◽  
The Other ◽  
Collagen Membrane ◽  
Biotechnological Applications ◽  
Casting Method ◽  
Cashew Gum ◽  
Macroscopic Analysis

Blends of polyvinyl alcohol (PVA) and angico gum (AG) and/or cashew gum (CG) were used to produce films by casting method. Morphological and mechanical properties of these films were studied and compared to the properties of a commercial collagen membrane of bovine origin (MBO). The films presented thickness varying from 70 to 140 μm (PVA/AG) and 140 to 200 μm (PVA/CG). Macroscopic analysis showed that a PVA/CG film was very similar to MBO regarding the color and transparency. The higher values of tensile strength (TS) and elastic modulus (EM) were observed in the film. On the other hand, PVA/CG and PVA/CG-AG presented the highest value of percentage of elongation (E%). Pearson’s Correlation Analysis revealed a positive correlation between TS and EM and a negative correlation between E% and EM. The PVA/CG film presented mechanical properties very similar to MBO, with the advantage of a higher E% (11.96) than MBO (2.94). The properties of the PVA blended films depended on the polysaccharide added in the blend, as well as the acid used as a catalyst. However, all produced films presented interesting mechanical characteristics which enables several biotechnological applications.

Sign in / Sign up

Export Citation Format

Share Document