scholarly journals Copper Chalcogenide–Copper Tetrahedrite Composites—A New Concept for Stable Thermoelectric Materials Based on the Chalcogenide System

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2635
Author(s):  
Andrzej Mikuła ◽  
Krzysztof Mars ◽  
Paweł Nieroda ◽  
Paweł Rutkowski
Keyword(s):  
Thermoelectric Materials ◽  
Ternary Phase ◽  
Two Phase ◽  
Temperature Dependences ◽  
Copper Chalcogenide ◽  
Cu Migration ◽  
The Stability ◽  
P Type ◽  
First Time ◽  
Melt Solidification

For the first time, an alternative way of improving the stability of Cu-based thermoelectric materials is proposed, with the investigation of two different copper chalcogenide–copper tetrahedrite composites, rich in sulfur and selenium anions, respectively. Based on the preliminary DFT results, which indicate the instability of Sb-doped copper chalcogenide, the Cu1.97S–Cu12Sb4S13 and Cu2−xSe–Cu3SbSe3 composites are obtained using melt-solidification techniques, with the tetrahedrite phase concentration varying from 1 to 10 wt.%. Room temperature structural analysis (XRD, SEM) indicates the two-phase structure of the materials, with ternary phase precipitates embed within the copper chalcogenide matrix. The proposed solution allows for successful blocking of excessive Cu migration, with stable electrical conductivity and Seebeck coefficient values over subsequent thermal cycles. The materials exhibit a p-type, semimetallic character with high stability, represented by a near-constant power factor (PF)—temperature dependences between individual cycles. Finally, the thermoelectric figure-of-merit ZT parameter reaches about 0.26 (623 K) for the Cu1.97S–Cu12Sb4S13 system, in which case increasing content of tetrahedrite is a beneficial effect, and about 0.44 (623 K) for the Cu2−xSe–Cu3SbSe3 system, where increasing the content of Cu3SbSe3 negatively influences the thermoelectric performance.

The influence of the Stokes and Archimedes forces on the stability of a two-phase flow

2003 ◽  
Vol 3 ◽  
pp. 266-270
Author(s):  
B.H. Khudjuyerov ◽  
I.A. Chuliev
Keyword(s):  
Spectral Method ◽  
Stability Region ◽  
Gas Flow ◽  
Two Phase Flow ◽  
Solid Phase ◽  
Stability Characteristic ◽  
Phase Flow ◽  
Two Phase ◽  
The Stability

The problem of the stability of a two-phase flow is considered. The solution of the stability equations is performed by the spectral method using polynomials of Chebyshev. A decrease in the stability region gas flow with the addition of particles of the solid phase. The analysis influence on the stability characteristic of Stokes and Archimedes forces.

p‐Type Plastic Inorganic Thermoelectric Materials

2021 ◽  
pp. 2100883
Author(s):  
Zhiqiang Gao ◽  
Qingyu Yang ◽  
Pengfei Qiu ◽  
Tian‐Ran Wei ◽  
Shiqi Yang ◽  
...  
Keyword(s):  
Thermoelectric Materials ◽  
P Type

scholarly journals Deciphering the effects of kosmotrope and chaotrope salts during aqueous two phase extraction (ATPE) of polyphenolic compounds and glycoalkaloids from the leaves of a nutraceutical plant, Solanum retroflexum, with the aid of UPLC-QTOF-MS

2021 ◽  
Vol 64 (1) ◽  
Author(s):  
Tebogo Mokgehle ◽  
Ntakadzeni Madala ◽  
Wilson Gitari ◽  
Nikita Tavengwa
Keyword(s):  
Polar Compounds ◽  
Ultra Performance Liquid Chromatography ◽  
Polyphenolic Compounds ◽  
Phase Extraction ◽  
Two Phase ◽  
Solanum Retroflexum ◽  
Chaotropic Salts ◽  
Almost All ◽  
First Time ◽  
Aqueous Two Phase Extraction

AbstractSolanum plants (Solanaceae) are renowned source of nutraceuticals and have widely been explored for their phytochemical constituents. This work investigated the effects of kosmotropic and chaotropic salts on the number of phytochemicals extracted from the leaves of a nutraceutical plant, Solanum retroflexum, and analyzed on the ultra-performance liquid chromatography hyphenated to a quadrupole time of flight mass spectrometer (UPLC-QTOF-MS) detector. Here, a total of 20 different compounds were putatively characterized. The majority of the identified compounds were polyphenols and glycoalkaloids. Another compound, caffeoyl malate was identified for the first time in this plant. Glycoalkaloids such as solanelagnin, solamargine, solasonine, β-solanine (I) and β-solanine (II) were found to be extracted by almost all the salts used herein. Kosmotrope salts, overall, were more efficient in extracting polar compounds with 4 more polyphenolic compounds extracted compared to the chaotropes. Chaotropes were generally more selective for the extraction of less polar compounds (glycoalkaloids) with 3 more extracted than the kosmotropes. The chaotrope and the kosmotrope that extracted the most metabolites were NaCl and Na2SO4, respectively, with 12 metabolites extracted for each salt. This work demonstrated that a comprehensive metabolome of S. retroflexum, more than what was previously reported on the same plant, can be achieved by application of kosmotropes and chaotropes as extractants with the aid of the Aqueous Two Phase Extraction approach. The best-performing salts, Na2SO4 or NaCl, could potentially be applied on a commercial scale, to meet the ever-growing demand of the studied metabolites. The Aqueous Two Phase Extraction technique was found to be efficient in simultaneous extraction of multiple metabolites which can be applied in metabolomics.

scholarly journals A Novel Approach to Fabricate Foam Ceramics from Steel Slag

2020 ◽  
Vol 2020 ◽  
pp. 1-7
Author(s):  
Yu Zheng ◽  
Xudong Luo ◽  
Jinlong Yang ◽  
Wenlong Huo ◽  
Chi Kang
Keyword(s):  
Compressive Strength ◽  
Ph Value ◽  
Steel Slag ◽  
Raw Material ◽  
Solid Loading ◽  
Insulation Material ◽  
Ceramic Foams ◽  
Novel Approach ◽  
The Stability ◽  
First Time

A novel approach is used for fabricating steel slag foam ceramics based on the particle-stabilized foaming method. In this work, steel slag was used as the raw material and propyl gallate (PG) was used as the surface modifier. For the first time, steel slag ceramic foams were successfully fabricated based on particle-stabilized foams. The results show that the stability of the ceramic foams was closely related to the pH value and PG concentration. The porosity and compressive strength could be controlled by changing the solid loading of steel slag and sintering temperature. The porosity of steel slag foam ceramics ranged from 85.6% to 62.53%, and the compressive strength was from 1.74 MPa to 10.42 MPa. The thermal conductivity of steel slag foam ceramics was only 0.067 W (m·K)−1, which shows that it could be used as a thermal insulation material.

scholarly journals Temporal Stability and Biodiversity of Two Complex Antilisterial Cheese-Ripening Microbial Consortia

2003 ◽  
Vol 69 (7) ◽  
pp. 4012-4018 ◽  
Author(s):  
Ariel Maoz ◽  
Ralf Mayr ◽  
Siegfried Scherer
Keyword(s):  
Species Composition ◽  
Bacterial Species ◽  
Temporal Stability ◽  
Individual Characteristics ◽  
Microbial Consortia ◽  
Cheese Ripening ◽  
Safe Food ◽  
The Stability ◽  
The Individual ◽  
First Time

ABSTRACT The temporal stability and diversity of bacterial species composition as well as the antilisterial potential of two different, complex, and undefined microbial consortia from red-smear soft cheeses were investigated. Samples were collected twice, at 6-month intervals, from each of two food producers, and a total of 400 bacterial isolates were identified by Fourier-transform infrared spectroscopy and 16S ribosomal DNA sequence analysis. Coryneform bacteria represented the majority of the isolates, with certain species being predominant. In addition, Marinolactobacillus psychrotolerans, Halomonas venusta, Halomonas variabilis, Halomonas sp. (106 to 107 CFU per g of smear), and an unknown, gram-positive bacterium (107 to 108 CFU per g of smear) are described for the first time in such a consortium. The species composition of one consortium was quite stable over 6 months, but the other consortium revealed less diversity of coryneform species as well as less stability. While the first consortium had a stable, extraordinarily high antilisterial potential in situ, the antilisterial activity of the second consortium was lower and decreased with time. The cause for the antilisterial activity of the two consortia remained unknown but is not due to the secretion of soluble, inhibitory substances by the individual components of the consortium. Our data indicate that the stability over time and a potential antilisterial activity are individual characteristics of the ripening consortia which can be monitored and used for safe food production without artificial preservatives.

scholarly journals Determining Accurate Vaccination Coverage Rates for Adolescents: The National Immunization Survey-Teen 2006

2009 ◽  
Vol 124 (5) ◽  
pp. 642-651 ◽  
Author(s):  
Nidhi Jain ◽  
James A. Singleton ◽  
Margrethe Montgomery ◽  
Benjamin Skalland
Keyword(s):  
Vaccination Coverage ◽  
National Level ◽  
National Sample ◽  
Two Phase ◽  
National Immunization ◽  
Level Data ◽  
Control And Prevention ◽  
Coverage Rates ◽  
First Time ◽  
National Immunization Survey

Since 1994, the Centers for Disease Control and Prevention has funded the National Immunization Survey (NIS), a large telephone survey used to estimate vaccination coverage of U.S. children aged 19–35 months. The NIS is a two-phase survey that obtains vaccination receipt information from a random-digit-dialed survey, designed to identify households with eligible children, followed by a provider record check, which obtains provider-reported vaccination histories for eligible children. In 2006, the survey was expanded for the first time to include a national sample of adolescents aged 13–17 years, called the NIS-Teen. This article summarizes the methodology used in the NIS-Teen. In 2008, the NIS-Teen was expanded to collect state-specific and national-level data to determine vaccination coverage estimates. This survey provides valuable information to guide immunization programs for adolescents.

12 kV 4H-SiC p-IGBTs with Record Low Specific On-Resistance

2008 ◽  
Vol 600-603 ◽  
pp. 1187-1190 ◽  
Author(s):  
Q. Jon Zhang ◽  
Charlotte Jonas ◽  
Joseph J. Sumakeris ◽  
Anant K. Agarwal ◽  
John W. Palmour
Keyword(s):  
Carrier Lifetime ◽  
Drift Region ◽  
Gate Bias ◽  
Enhancement Layer ◽  
Channel Mobility ◽  
Dc Characteristics ◽  
Blocking Voltage ◽  
High Carrier ◽  
P Type ◽  
First Time

DC characteristics of 4H-SiC p-channel IGBTs capable of blocking -12 kV and conducting -0.4 A (-100 A/cm2) at a forward voltage of -5.2 V at 25°C are demonstrated for the first time. A record low differential on-resistance of 14 mW×cm2 was achieved with a gate bias of -20 V indicating a strong conductivity modulation in the p-type drift region. A moderately doped current enhancement layer grown on the lightly doped drift layer effectively reduces the JFET resistance while maintains a high carrier lifetime for conductivity modulation. A hole MOS channel mobility of 12.5 cm2/V-s at -20 V of gate bias was measured with a MOS threshold voltage of -5.8 V. The blocking voltage of -12 kV was achieved by Junction Termination Extension (JTE).

Fabrication of Bi-Te Based Thermoelectric Semiconductors by Using Hybrid Powders

2005 ◽  
Vol 297-300 ◽  
pp. 875-880
Author(s):  
Cheol Ho Lim ◽  
Ki Tae Kim ◽  
Yong Hwan Kim ◽  
Dong Choul Cho ◽  
Young Sup Lee ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Single Crystals ◽  
Thermoelectric Properties ◽  
Thermoelectric Materials ◽  
Figure Of Merit ◽  
Bending Strength ◽  
Mixing Ratio ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
P Type

P-type Bi0.5Sb1.5Te3 compounds doped with 3wt% Te were fabricated by spark plasma sintering and their mechanical and thermoelectric properties were investigated. The sintered compounds with the bending strength of more than 50MPa and the figure-of-merit 2.9×10-3/K were obtained by controlling the mixing ratio of large powders (PL) and small powders (PS). Compared with the conventionally prepared single crystal thermoelectric materials, the bending strength was increased up to more than three times and the figure-of-merit Z was similar those of single crystals. It is expected that the mechanical properties could be improved by using hybrid powders without degradation of thermoelectric properties.

GalnAsSb Materials for Thermophotovoltaics

1996 ◽  
Vol 450 ◽  
Author(s):  
C. A. Wang ◽  
G. W. Turner ◽  
M. J. Manfra ◽  
H. K. Choi ◽  
D. L. Spears
Keyword(s):  
Room Temperature ◽  
Molecular Beam ◽  
Hole Concentration ◽  
Organometallic Vapor Phase Epitaxy ◽  
Room Temperature Photoluminescence ◽  
P Type ◽  
First Time ◽  
Lattice Matched ◽  
Comparable Quality ◽  
Peak Emission

ABSTRACTGai1−xInxASySb1-y (0.06 < x < 0.18, 0.05 < y < 0.14) epilayers were grown lattice-matched to GaSb substrates by low-pressure organometallic vapor phase epitaxy (OMVPE) using triethylgallium, trimethylindium, tertiarybutylarsine, and trimethylantimony. These epilayers have a mirror-like surface morphology, and exhibit room temperature photoluminescence (PL) with peak emission wavelengths (λP,300K) out to 2.4 μm. 4K PL spectra have a full width at half-maximum of 11 meV or less for λP,4K < 2.1 μm (λP,300K = 2.3 μm). Nominally undoped layers are p-type with typical 300K hole concentration of 9 × 1015 cm−3 and mobility ∼ 450 to 580 cm2/V-s for layers grown at 575°C. Doping studies are reported for the first time for GalnAsSb layers doped n type with diethyltellurium and p type with dimethylzinc. Test diodes of p-GalnAsSb/n-GaSb have an ideality factor that ranges from 1.1 to 1.3. A comparison of electrical, optical, and structural properties of epilayers grown by molecular beam epitaxy indicates OMVPE-grown layers are of comparable quality.

Sign in / Sign up

Export Citation Format

Share Document