scholarly journals Investigation of Mechanical and Physical Properties of Big Sheep Horn as an Alternative Biomaterial for Structural Applications

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4039
Author(s):  
Tajammul Hussain M. Mysore ◽  
Arun Y. Patil ◽  
G. U. Raju ◽  
N. R. Banapurmath ◽  
Prabhakar M. Bhovi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Yield Strength ◽  
Moisture Absorption ◽  
Failure Strain ◽  
Flexural Modulus ◽  
Physical Property ◽  
Significant Loss ◽  
Two Samples ◽  
Structural Applications

This paper investigates the physical and mechanical properties of bighorns of Deccani breed sheep native from Karnataka, India. The exhaustive work comprises two cases. First, rehydrated (wet) and ambient (dry) conditions, and second, the horn coupons were selected for longitudinal and lateral (transverse) directions. More than seventy-two samples were subjected to a test for physical and mechanical property extraction. Further, twenty-four samples were subjected to physical property testing, which included density and moisture absorption tests. At the same time, mechanical testing included analysis of the stress state dependence with the horn keratin tested under tension, compression, and flexural loading. The mechanical properties include the elastic modulus, yield strength, ultimate strength, failure strain, compressive strength, flexural strength, flexural modulus, and hardness. The results showed anisotropy and depended highly on the presence of water content more than coupon orientation. Wet conditioned specimens had a significant loss in mechanical properties compared with dry specimens. The observed outcomes were shown at par with results for yield strength of 53.5 ± 6.5 MPa (which is better than its peers) and a maximum compressive stress of 557.7 ± 5 MPa (highest among peers). Young’s modulus 6.5 ± 0.5 GPa and a density equivalent to a biopolymer of 1.2 g/cc are expected to be the lightest among its peers; flexural strength 168.75 MPa, with lowest failure strain percentage of 6.5 ± 0.5 and Rockwell hardness value of 60 HRB, seem best in the class of this category. Simulation study identified a suitable application area based on impact and fatigue analysis. Overall, the exhaustive experimental work provided many opportunities to use this new material in various diversified applications in the future.

scholarly journals Comparison of Mechanical Properties of PMMA Disks for Digitally Designed Dentures

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1745
Author(s):  
Tamaki Hada ◽  
Manabu Kanazawa ◽  
Maiko Iwaki ◽  
Awutsadaporn Katheng ◽  
Shunsuke Minakuchi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Water Sorption ◽  
Water Solubility ◽  
Flexural Modulus ◽  
Manufacturing Method ◽  
Heat Curing ◽  
Significant Difference ◽  
Cad Cam ◽  
Curing Method

In this study, the physical properties of a custom block manufactured using a self-polymerizing resin (Custom-block), the commercially available CAD/CAM PMMA disk (PMMA-disk), and a heat-polymerizing resin (Conventional PMMA) were evaluated via three different tests. The Custom-block was polymerized by pouring the self-polymerizing resin into a special tray, and Conventional PMMA was polymerized with a heat-curing method, according to the manufacturer’s recommended procedure. The specimens of each group were subjected to three-point bending, water sorption and solubility, and staining tests. The results showed that the materials met the requirements of the ISO standards in all tests, except for the staining tests. The highest flexural strength was exhibited by the PMMA-disk, followed by the Custom-block and the Conventional PMMA, and a significant difference was observed in the flexural strengths of all the materials (p < 0.001). The Custom-block showed a significantly higher flexural modulus and water solubility. The water sorption and discoloration of the Custom-block were significantly higher than those of the PMMA-disk, but not significantly different from those of the Conventional PMMA. In conclusion, the mechanical properties of the three materials differed depending on the manufacturing method, which considerably affected their flexural strength, flexural modulus, water sorption and solubility, and discoloration.

Mechanical properties and toughening mechanisms of epoxy/graphene nanocomposites

2015 ◽  
Vol 35 (3) ◽  
pp. 257-266 ◽  
Author(s):  
Rahim Eqra ◽  
Kamal Janghorban ◽  
Habib Daneshmanesh
Keyword(s):  
Mechanical Properties ◽  
Fracture Surface ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Graphene Nanosheets ◽  
Flexural Modulus ◽  
Mechanical Tests ◽  
Toughening Mechanism ◽  
Graphene Nanocomposites

Abstract Because of extraordinary physical, chemical and mechanical properties, graphene nanosheets (GNS) are suitable fillers for optimizing the properties of different polymers. In this research, the effect of GNS content (up to 1 wt.%) on tensile and flexural properties, morphology of fracture surface, and toughening mechanism of epoxy were investigated. Results of mechanical tests showed a peak for tensile and flexural strength of samples with 0.1 wt.% GNS such that the tensile and flexural strength improved by 13% and 3.3%, respectively. The Young’s modulus and flexural modulus increased linearly with GNS content, although the behavior of the Young’s modulus was more remarkable. Morphological investigations confirmed this behavior because the GNS dispersion in the epoxy matrix was uniform at lower contents and agglomerated at higher contents. Finally, microscopical observation showed that the major toughening mechanism of graphene-epoxy nanocomposites was crack path deflection, which changed the mirror fracture surface of the pure epoxy to rough surface.

scholarly journals Preliminary Study on Mechanical Properties of 3D Printed Multimaterials ABS/PC Parts: Effect of Printing Parameters

2021 ◽  
Vol 32 (2) ◽  
pp. 87-104
Author(s):  
Pui-Voon Yap ◽  
Ming-Yeng Chan ◽  
Seong-Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flexural Modulus ◽  
Nozzle Diameter ◽  
Fused Deposition ◽  
Printing Parameters ◽  
Printing Speed

This research work highlights the mechanical properties of multi-material by fused deposition modelling (FDM). The specimens for tensile and flexural test have been printed using polycarbonate (PC) material at different combinations of printing parameters. The effects of varied printing speed, infill density and nozzle diameter on the mechanical properties of specimens have been investigated. Multi-material specimens were fabricated with acrylonitrile butadiene styrene (ABS) as the base material and PC as the reinforced material at the optimum printing parameter combination. The specimens were then subjected to mechanical testing to observe their tensile strength, Young’s modulus, percentage elongation, flexural strength and flexural modulus. The outcome of replacing half of ABS with PC to create a multi-material part has been examined. As demonstrated by the results, the optimum combination of printing parameters is 60 mm/s printing speed, 15% infill density and 0.8 mm nozzle diameter. The combination of ABS and PC materials as reinforcing material has improved the tensile strength (by 38.46%), Young’s modulus (by 23.40%), flexural strength (by 23.90%) and flexural modulus (by 37.33%) while reducing the ductility by 14.31% as compared to pure ABS. The results have been supported by data and graphs of the analysed specimens.

scholarly journals Influence of Furfuryl Alcohol Fiber Pre-Treatment on the Moisture Absorption and Mechanical Properties of Flax Fiber Composites

Fibers ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 59 ◽  
Author(s):  
Yunlong Jia ◽  
Bodo Fiedler
Keyword(s):  
Mechanical Properties ◽  
Furfuryl Alcohol ◽  
Moisture Absorption ◽  
Natural Fiber ◽  
Tensile Tests ◽  
Fiber Composites ◽  
Flax Fiber ◽  
Moisture Resistance ◽  
Structural Applications ◽  
Pre Treatment

Poor moisture resistance of natural fiber reinforced bio-composites is a major concern in structural applications. Many efforts have been devoted to alleviate degradation of bio-composites caused by moisture absorption. Among them, fiber pre-treatment has been proven to be effective. This paper proposes an alternative “green” fiber pretreatment with furfuryl alcohol. Pre-treatments with different parameters were performed and the influence on the mechanical properties of fiber bundles and composites was investigated. Moisture resistance of composites was evaluated by water absorption tests. Mechanical properties of composites with different water contents were analyzed in tensile tests. The results show that furfuryl alcohol pretreatment is a promising method to improve moisture resistance and mechanical properties (e.g., Young’s modulus increases up to 18%) of flax fiber composites.

Effect of Moisture on the Mechanical Properties of Additively Manufactured PLA, ABS and PLA/SiC Composites

2019 ◽  
Author(s):  
Padmalatha Kakanuru ◽  
Kishore Pochiraju
Keyword(s):  
Mechanical Properties ◽  
Room Temperature ◽  
Moisture Absorption ◽  
Failure Strain ◽  
Acrylonitrile Butadiene Styrene ◽  
Distilled Water ◽  
Weight Percentage ◽  
Lower Volume ◽  
Sic Composites ◽  
Butadiene Styrene

Abstract In this study the tensile properties of additively manufactured Polylactic Acid (PLA), Acrylonitrile Butadiene Styrene (ABS) and Silicon Carbide (SiC) particulate filled PLA composites were assessed after aging for 4.5 months at 50°C in distilled water. The maximum moisture gain in PLA was about 16% by weight, and ABS gained 0.65%. In PLA/SiC composites, the weight gain due to moisture absorption was inversely proportional to the weight percentage of SiC loading. The PLA specimens degraded completely during aging without measurable residual strength. While the addition of SiC to PLA increased the room temperature tensile strength at lower volume fractions of SiC, the degradation of aged strength was similar to that of the pure PLA. The PLA/SiC composites had no measurable strength after aging. The ABS specimens retained their strength and failure strain after aging.

scholarly journals A Method of Large-Scale Resource Utilization of Algae—Eutrophic Waste from Lake Chao, China: Preparation and Performance Optimization of Composite Packaging Materials

2019 ◽  
Vol 11 (22) ◽  
pp. 6462 ◽  
Author(s):  
Zhao ◽  
Fang ◽  
Wu ◽  
Zhang ◽  
Wang
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Resource Utilization ◽  
Performance Optimization ◽  
Large Scale ◽  
Flexural Modulus ◽  
Process Conditions ◽  
Single Factor ◽  
Preparation Conditions ◽  
Lake Chao

In order to realize the resource utilization of bloom algae from Lake Chao, this study presents the use of fresh algae to improve the mechanical and biological properties of low-density polyethylene (LDPE). In this study, the algae and LDPE were used as raw materials, maleic anhydride grafted polyethylene (PE-g-MAH), polyethylene wax (PE-wax) and white oil, and glycerin were used as the compatibilizer, lubricant, and plasticizer, respectively. The single factor experiments were conducted with these three individual factors, and the response surface methodology technique was used to optimize the process conditions. In the single factor experiments, the mechanical properties of the composites increased with additions of PE-g-MAH, PE-wax/white oil, and glycerin. Both flexural strength and flexural modulus were maximized to optimize the preparation conditions. The optimum preparation conditions were found as follows: algae powder of 15.00 wt%, LDPE of 85.00 wt%, PE-g-MAH of 4.00 wt%, lubricant of 2.67 wt%, and glycerin of 3.00 wt%. This resulted in 11.60 MPa of tensile strength, 9.95 MPa of flexural strength, and 241.00 MPa of flexural modulus. The mechanical properties of composites were greatly improved compared with the absence of additives. In addition, compared with LDPE resin, the degradability of the composite was improved, and the weight loss rate was 7.73% after 6 months. The results recommended that the composites of the algae from Lake Chao and LDPE resin could be a useful material in the packaging field. Generally, the prepared composite particles can be used to produce foam products, packaging bags, or hard packing boxes with special shapes. It is more environmentally friendly, and more able to meet the challenges of sustainable development.

THE INFLUENCE OF SiC COATING PROCESS ON THE PROPERTIES OF C/C COMPOSITES

2007 ◽  
Vol 14 (04) ◽  
pp. 817-820
Author(s):  
MIN HUANG ◽  
KE-ZHI LI ◽  
HE-JUN LI ◽  
QIAN-GANG FU ◽  
GUO-DONG SUN
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Failure Mode ◽  
Flexural Modulus ◽  
Pack Cementation ◽  
Bending Test ◽  
Carbon Composites ◽  
Coating Process ◽  
Three Point Bending ◽  
Coated Carbon

SiC coating for carbon/carbon composites was prepared by pack cementation method. The effects of coating process on the microstructure and the mechanical properties of C / C composites were analyzed by SEM and three-point bending test, respectively. As the infiltrated Si improved the interfaces bonding during the coating process, the flexural strength and flexural modulus of SiC -coated carbon/carbon composites were both increased by about 10% than the naked C / C composites. In addition, the mechanism of the change of failure mode of SiC coated C / C composites and naked C / C composites was addressed.

scholarly journals A Pilot Study on the Flexural Properties of Vinyl Ester Composites Filled with Glass Powder

2010 ◽  
Vol 123-125 ◽  
pp. 3-6
Author(s):  
Harry Ku ◽  
Mohan Trada ◽  
Rezwanul Huq
Keyword(s):  
Flexural Strength ◽  
Vinyl Ester ◽  
Glass Powder ◽  
Filler Content ◽  
Flexural Modulus ◽  
Research Centre ◽  
Flexural Properties ◽  
Structural Applications ◽  
Flexural Tests ◽  
Sufficient Strength

Vinyl ester resin was filled with of glass powder with a view to increasing the flexural strength of the composites for civil and structural applications by a research Centre on composites, University of Southern Queensland (USQ). In order to reduce costs, the Centre wishes to fill as much glass powder as possible to the resin subject to maintaining sufficient strength of the composites in civil and structural applications. This project varies the percentage by weight of the glass powder in the composites, which are then subjected to flexural tests. The flexural strength and strain of the glass powder filled vinyl ester composites decreased with increasing filler content but the flexural modulus was highest at 20 w/t % of glass powder. Scanning Electron Microscope (SEM) was used to analyze the fractured samples and it was found that the fractured surfaces examined were correlated with the flexural properties.

Study on Integrated Properties of PP Composites Filled with Rice Husks Powder

2011 ◽  
Vol 217-218 ◽  
pp. 347-352 ◽  
Author(s):  
Chun Xia He ◽  
Jun Jun Liu ◽  
Pan Fang Xue ◽  
Hong Yan Gu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Water Absorption ◽  
Volume Expansion ◽  
Flexural Modulus ◽  
Expansion Ratio ◽  
Rice Husks ◽  
Elongation Ratio ◽  
Pp Composites

The influence of the rice husks powder (RHP) content and its particle size distribution on the composite’s tensile strength, fracturing elongation ratio, flexural strength and flexural elastic modulus has been investigated. Respective water absorption and thermal properties of PP composites incorporated with different proportion of RHP have also been analyzed. The microstructure of fractured surfaces was further observed in scanning electron microscopy (SEM). The results showed that the composites with RHP of 245 μm have higher mechanical properties. The tensile strength and fracturing elongation ratio decrease with the increase of RHP content, and reach peak values in 30% RHP content. Water absorption and volume expansion ratio of the composite increase with the increasing of RHP content. Flexural strength and flexural modulus decrease after water absorption. When PHR content is low, the RHP particles are well distributed and the interface of RHP and PP is smooth. When PHR content is higher, the RHP particles tend to agglomerate, leading to poorer interface and lower mechanical properties, the composite failed with brittle fracture.

scholarly journals Influence of a Repeated Preheating Procedure on Mechanical Properties of Three Resin Composites

2015 ◽  
Vol 40 (2) ◽  
pp. 181-189 ◽  
Author(s):  
M D'Amario ◽  
F De Angelis ◽  
M Vadini ◽  
N Marchili ◽  
S Mummolo ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Vickers Microhardness ◽  
Flexural Modulus ◽  
Bending Test ◽  
Resin Composites ◽  
Three Point Bending ◽  
Main Effect ◽  
Dependent Variables ◽  
Marginal Means

SUMMARY The aim of this study was to assess the flexural strength, flexural elastic modulus and Vickers microhardness of three resin composites prepared at room temperature or cured after one or repeated preheating cycles to a temperature of 39°C. Three resin composites were evaluated: Enamel Plus HFO (Micerium), Opallis (FGM), and Ceram X Duo (Dentsply DeTrey). For each trial, one group of specimens of each material was fabricated under ambient laboratory conditions, whereas in the other groups, the composites were cured after 1, 10, 20, 30, or 40 preheating cycles to a temperature of 39°C in a preheating device. Ten rectangular prismatic specimens (25 × 2 × 2 mm) were prepared for each group (N=180; n=10) and subjected to a three-point bending test for flexural strength and flexural modulus evaluation. Vickers microhardness was assessed on 10 cylindrical specimens from each group (N=180; n=10). Statistical analysis showed that, regardless of the material, the number of heating cycles was not a significant factor and was unable to influence the three mechanical properties tested. However, a significant main effect of the employed material on the marginal means of the three dependent variables was detected.

Sign in / Sign up

Export Citation Format

Share Document