scholarly journals Comparison of Different Synthetic Routes of Hybrid Hematite-TiO2 Nanotubes-Based Electrodes

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4501
Author(s):  
Ana Luiza Fornazari ◽  
Judith Castillo-Rodriguez ◽  
Daniel Correa-Encalada ◽  
Enrique A. Dalchiele ◽  
Samuel A. Hevia ◽  
...  
Keyword(s):  
Composite Material ◽  
Electrochemical Synthesis ◽  
Chemical Vapor ◽  
Flat Band ◽  
X Ray Diffraction ◽  
Silar Method ◽  
Negative Shift ◽  
First Case ◽  
Titanium Oxide Nanotubes ◽  
Impedance Characterization

Nowadays, green hydrogen is an important niche of interest in which the search for a suitable composite material is indispensable. In this sense, titanium oxide nanotubes (TiO2 nanotube, TNTs) were prepared from double anodic oxidation of Ti foil in ethylene glycol electrolyte. The morphology of the nanotubes was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Once characterized, nanotubes were used as templates for the deposition of hematite. The use of three synthetic procedures was assayed: Chemical Vapor Deposition (CVD), Successive Ionic Layer Adsorption and Reaction (SILAR), and electrochemical synthesis. In the first case, CVD, the deposition of hematite onto TiO2 yielded an uncovered substrate with the oxide and a negative shift of the flat band potential. On the other hand, the SILAR method yielded a considerable amount of hematite on the surface of nanotubes, leading to an obstruction of the tubes in most cases. Finally, with the electrochemical synthesis, the composite material obtained showed great control of the deposition, including the inner surface of the TNT. In addition, the impedance characterization showed a negative shift, indicating the changes of the interface electrode–electrolyte due to the modification with hematite. Finally, the screening of the methods showed the electrochemical synthesis as the best protocol for the desired material.

Chemical synthesis and study of structural and optoelectronic properties of CdS thin films: Effect of SILAR growth cycles

2015 ◽  
Vol 9 (3) ◽  
pp. 2461-2469
Author(s):  
S. R. Gosavi ◽  
K. B. Chaudhari
Keyword(s):  
Thin Films ◽  
Average Crystallite Size ◽  
X Ray Diffraction ◽  
Silar Method ◽  
Growth Cycles ◽  
Glass Substrates ◽  
Layer Adsorption ◽  
Cds Thin Films ◽  
Structural And Optoelectronic Properties ◽  
Deposited Film

CdS thin films were deposited on glass substrates by using successive ionic layer adsorption and reaction (SILAR) method at room temperature. The effect of SILAR growth cycles on structural, morphological, optical and electrical properties of the films has been studied.  The thickness of the deposited film is measured by employing weight difference method. The X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM) studies showed that all the films exhibit polycrystalline nature and are covered well with glass substrates. The values of average crystallite size were found to be 53 nm, 58 nm, 63 nm and 71 nm corresponding to the thin films deposited with 30, 40, 50 and 60 SILAR growth cycles respectively. From the UV–VIS spectra of the deposited thin films, it was seen that both the absorption properties and energy bandgap of the films changes with increasing number of SILAR growth cycles. A decrease of electrical resistivity has been observed with increasing SILAR growth cycle. 

scholarly journals Temperature Dependence of Stress and Optical Properties in AlN Films Grown by MOCVD

Nanomaterials ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 698
Author(s):  
Wenwang Wei ◽  
Yi Peng ◽  
Jiabin Wang ◽  
Muhammad Farooq Saleem ◽  
Wen Wang ◽  
...  
Keyword(s):  
Optical Properties ◽  
Compressive Stress ◽  
Sapphire Substrate ◽  
Light Transmission ◽  
Chemical Vapor ◽  
Biaxial Stress ◽  
X Ray Diffraction ◽  
Patterned Sapphire Substrate ◽  
Transmission Electron ◽  
Nano Patterning

AlN epilayers were grown on a 2-inch [0001] conventional flat sapphire substrate (CSS) and a nano-patterned sapphire substrate (NPSS) by metalorganic chemical vapor deposition. In this work, the effect of the substrate template and temperature on stress and optical properties of AlN films has been studied by using Raman spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-visible spectrophotometer and spectroscopic ellipsometry (SE). The AlN on NPSS exhibits lower compressive stress and strain values. The biaxial stress decreases from 1.59 to 0.60 GPa for AlN on CSS and from 0.90 to 0.38 GPa for AlN on NPSS sample in the temperature range 80–300 K, which shows compressive stress. According to the TEM data, the stress varies from tensile on the interface to compressive on the surface. It can be deduced that the nano-holes provide more channels for stress relaxation. Nano-patterning leads to a lower degree of disorder and stress/strain relaxes by the formation of the nano-hole structure between the interface of AlN epilayers and the substrate. The low crystal disorder and defects in the AlN on NPSS is confirmed by the small Urbach energy values. The variation in bandgap (Eg) and optical constants (n, k) with temperature are discussed in detail. Nano-patterning leads to poor light transmission due to light scattering, coupling, and trapping in nano-holes.

Preparation and Characrization of Tic/C Composite Fiber by Chemical Vapor Deposition

2012 ◽  
Vol 455-456 ◽  
pp. 935-938
Author(s):  
Hai Quan Wang
Keyword(s):  
Chemical Vapor Deposition ◽  
Carbon Fibers ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Composite Fiber ◽  
Composite Fibers ◽  
X Ray Diffraction ◽  
Reaction Conditions ◽  
Tic Particle ◽  
Higher Temperature

- TiC/C composite fibers were prepared by vapor phase titanizing of the regular carbon fibers via chemical vapor deposition (CVD). The carbon fibers were titanized from the surface of the fiber to the core. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were applied to characterize the morphology and structure of the TiC/C composite fibers. The influences of CVD reaction conditions such as temperature and reaction time on the TiC particle size and the thickness of the deposited layer were investigated. Higher temperature and longer time resulted in the growth of bigger size of the TiC crystal particles, and the particle uniformity was also decreased.

Low Temperature Large Scale CVD Synthesis of Nano Onion-Like Fullerenes

2012 ◽  
Vol 490-495 ◽  
pp. 3211-3214 ◽  
Author(s):  
Lei Shan Chen ◽  
Cun Jing Wang
Keyword(s):  
Electron Microscopy ◽  
Low Temperature ◽  
Aluminum Hydroxide ◽  
Large Scale ◽  
Iron Catalyst ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Naoh Solution ◽  
Synthesis Reactions

Synthesis reactions were carried out by chemical vapor deposition using iron catalyst supported on aluminum hydroxide at 400 °C and 420 °C, in the presence of argon as carrier gas and acetylene as carbon source. The aluminum hydroxide support was separated by refluxing the samples in 40% NaOH solution for 2 h and 36% HCl solution for 24 h, respectively. The samples were characterized by field-emission scanning electron microscopy, energy dispersive spectroscopy, high-resolution transmission electron microscopy and X-ray diffraction. The results show that carbon nanotubes were the main products at 420 °C, while large scale high purity nano onion-like fullerenes encapsulating Fe3C, with almost uniform sizes ranging from 10-50 nm, were obtained at the low temperature of 400 °C.

scholarly journals Fabrication and Physical Properties of Single-Crystalline Βeta-FeSi2 Nanowires

2020 ◽  
Vol 15 (1) ◽  
Author(s):  
Chih-Yung Yang ◽  
Shu-Meng Yang ◽  
Yu-Yang Chen ◽  
Kuo-Chang Lu
Keyword(s):  
Electron Microscopy ◽  
Physical Properties ◽  
Chemical Vapor ◽  
Chemical Vapor Deposition Method ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Field Emitters ◽  
Transmission Electron ◽  
Single Source Precursor ◽  
Carrier Gases

Abstract In this study, self-catalyzed β-FeSi2 nanowires, having been wanted but seldom achieved in a furnace, were synthesized via chemical vapor deposition method where the fabrication of β-FeSi2 nanowires occurred on Si (100) substrates through the decomposition of the single-source precursor of anhydrous FeCl3 powders at 750–950 °C. We carefully varied temperatures, duration time, and the flow rates of carrier gases to control and investigate the growth of the nanowires. The morphology of the β-FeSi2 nanowires was observed with scanning electron microscopy (SEM), while the structure of them was analyzed with X-ray diffraction (XRD) and transmission electron microscopy (TEM). The growth mechanism has been proposed and the physical properties of the iron disilicide nanowires were measured as well. In terms of the magnetization of β-FeSi2, nanowires were found to be different from bulk and thin film; additionally, longer β-FeSi2 nanowires possessed better magnetic properties, showing the room-temperature ferromagnetic behavior. Field emission measurements demonstrate that β-FeSi2 nanowires can be applied in field emitters.

Effect of Argon during Diamond Deposition by Hot Filament Chemical Vapor Deposition

2016 ◽  
Vol 869 ◽  
pp. 721-726 ◽  
Author(s):  
Divani C. Barbosa ◽  
Ursula Andréia Mengui ◽  
Mauricio R. Baldan ◽  
Vladimir J. Trava-Airoldi ◽  
Evaldo José Corat
Keyword(s):  
Growth Rate ◽  
Chemical Vapor Deposition ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Diamond Growth ◽  
Gas Mixture ◽  
X Ray Diffraction ◽  
Hot Filament ◽  
Argon Content

The effect of argon content upon the growth rate and the properties of diamond thin films grown with different grains sizes are explored. An argon-free and argon-rich gas mixture of methane and hydrogen is used in a hot filament chemical vapor deposition reactor. Characterization of the films is accomplished by scanning electron microscopy, Raman spectroscopy and high-resolution x-ray diffraction. An extensive comparison of the growth rate values and films morphologies obtained in this study with those found in the literature suggests that there are distinct common trends for microcrystalline and nanocrystalline diamond growth, despite a large variation in the gas mixture composition. Included is a discussion of the possible reasons for these observations.

OMCVD of thin films from metal diketonates and triphenylbismuth

1990 ◽  
Vol 5 (6) ◽  
pp. 1169-1175 ◽  
Author(s):  
A. D. Berry ◽  
R. T. Holm ◽  
M. Fatemi ◽  
D. K. Gaskill
Keyword(s):  
Electron Microscopy ◽  
Vapor Deposition ◽  
Atmospheric Pressure ◽  
Electron Spectroscopy ◽  
Auger Electron ◽  
Chemical Vapor ◽  
X Ray Diffraction ◽  
Strontium Barium ◽  
X Ray ◽  
Scanning Electron

Films containing the metals copper, yttrium, calcium, strontium, barium, and bismuth were grown by organometallic chemical vapor deposition (OMCVD). Depositions were carried out at atmospheric pressure in an oxygen-rich environment using metal beta-diketonates and triphenylbismuth. The films were characterized by Auger electron spectroscopy, Nomarski and scanning electron microscopy, and x-ray diffraction. The results show that films containing yttrium consisted of Y2O3 with a small amount of carbidic carbon, those with copper and bismuth were mixtures of oxides with no detectable carbon, and those with calcium, strontium, and barium contained carbonates. Use of a partially fluorinated barium beta-diketonate gave films of BaF2 with small amounts of BaCO3.

Control of Morphology and Growth Direction of Gallium Nitride Nanostructures

2003 ◽  
Vol 789 ◽  
Author(s):  
Seung Yong Bae ◽  
Hee Won Seo ◽  
Jeunghee Park
Keyword(s):  
Electron Microscopy ◽  
Gallium Nitride ◽  
Large Scale ◽  
Chemical Vapor ◽  
Growth Direction ◽  
Chemical Vapor Deposition Method ◽  
X Ray Diffraction ◽  
Oxide Mixture ◽  
Temperature Range ◽  
Transmission Electron

ABSTRACTVarious shaped single-crystalline gallium nitride (GaN) nanostructures were produced by chemical vapor deposition method in the temperature range of 900–1200 °C. Scanning electron microscopy, transmission electron microscopy, electron diffraction, x-ray diffraction, electron energy loss spectroscopy, Raman spectroscopy, and photoluminescence were used to investigate the structural and optical properties of the GaN nanostructures. We controlled the GaN nanostructures by the catalyst and temperature. The cylindrical and triangular shaped nanowires were synthesized using iron and gold nanoparticles as catalysts, respectively, in the temperature range of 900 – 1000 °C. We synthesized the nanobelts, nanosaws, and porous nanowires using gallium source/ boron oxide mixture. When the temperature of source was 1100 °C, the nanobelts having a triangle tip were grown. At the temperature higher up to 1200 °C the nanosaws and porous nanowires were formed with a large scale. The cylindrical nanowires have random growth direction, while the triangular nanowires have uniform growth direction [010]. The growth direction of the nanobelts is perpendicular to the [010]. Interestingly, the nanosaws and porous nanowires exhibit the same growth direction [011]. The shift of Raman, XRD, and PL bands from those of bulk was correlated with the strains of the GaN nanostructures.

Composition Analysis of Ge/Si1-xGex: C Buffer on Silicon Measured by Planar Scanning Energy Dispersive Spectroscopy

2011 ◽  
Vol 383-390 ◽  
pp. 7619-7623
Author(s):  
Z Z Lu ◽  
F. Yu ◽  
L. Yu ◽  
L. H. Cheng ◽  
P. Han
Keyword(s):  
Energy Dispersive Spectroscopy ◽  
Chemical Vapor ◽  
Energy Dispersive ◽  
Composition Analysis ◽  
X Ray Diffraction ◽  
Si Substrate ◽  
Composition Distribution ◽  
X Ray ◽  
Cvd Method ◽  
Substrate Structure

In this work, Si, Ge element composition distribution in Ge /Si1-xGex:C /Si substrate structure has been characterized and modified by planar scanning energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD). The Ge /Si1-xGex:C /Si substrate samples are grown by chemical vapor deposition (CVD) method. The accuracy of EDS value can be improved by ~ 32%. And the modified EDS results indicate the Ge distribution in the Ge/Si1-xGex:C/Si sub structure.

Sign in / Sign up

Export Citation Format

Share Document