scholarly journals Influence of the Size of the Fiber Filler of Corn Stalks in the Polylactide Matrix Composite on the Mechanical and Thermomechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (23) ◽  
pp. 7281
Author(s):  
Daniel Łączny ◽  
Marek Macko ◽  
Krzysztof Moraczewski ◽  
Zbigniew Szczepański ◽  
Andrzej Trafarski

This paper presents results of a study on the effect of filler size in the form of 15 wt% corn stalk (CS) fibers on the mechanical and thermomechanical properties of polylactide (PLA) matrix composites. In the test, polylactidic acid (PLA) is filled with four types of length of corn stalk fibers with a diameter of 1 mm, 1.6 mm, 2 mm and 4 mm. The composites were composed by single screw extrusion and then samples were prepared by injection molding. The mechanical properties of the composites were determined by static tensile test, static bending test and Charpy impact test while the thermo-mechanical properties were determined by dynamic mechanical thermal analysis (DMTA). The composite structures were also observed using X-ray microcomputed tomography and scanning electron microscopy. In the PLA/CS composites, as the filler fiber diameter increased, the degradation of mechanical properties relative to the matrix was observed including tensile strength (decrease 22.9–51.1%), bending strength (decrease 18.9–36.6%) and impact energy absorption (decrease 58.8–69.8%). On the basis of 3D images of the composite structures for the filler particles larger than 2 mm a weak dispersion with the filler was observed, which is reflected in a significant deterioration of the mechanical and thermomechanical properties of the composite. The best mechanical and thermomechanical properties were found in the composite with filler fiber of 1 mm diameter. Processing resulted in a more than 6-fold decrease in filler fiber length from 719 ± 190 µm, 893 ± 291 µm, 1073 ± 219 µm, and 1698 ± 636 µm for CS1, CS1.6, CS2, and CS4 fractions, respectively, to 104 ± 43 µm, 123 ± 60 µm, 173 ± 60 µm, and 227 ± 89 µm. The fabricated green composites with 1 to 2 mm corn stalk fiber filler are an alternative to traditional plastic based materials in some applications.

2013 ◽  
Vol 486 ◽  
pp. 283-288
Author(s):  
Ladislav Fojtl ◽  
Soňa Rusnáková ◽  
Milan Žaludek

This research paper deals with an investigation of the influence of honeycomb core compression on the mechanical properties of sandwich structures. These structures consist of prepreg facing layers and two different material types of honeycomb and are produced by modified compression molding called Crush-Core technology. Produced structures are mechanically tested in three-point bending test and subjected to low-velocity impact and Charpy impact test.


2007 ◽  
Vol 537-538 ◽  
pp. 41-46 ◽  
Author(s):  
László Kuzsella ◽  
Imre Szabó

The wood is one of the most favourable structural material. It appears on all fields of the ordinary life. It is difficult to say an application where the wood is not used due to its cheap price, availability and just simply the beauty. Beside of the wide range of process technologies a new process appeared. This process changes the properties of the material and brings many new applications to this traditional material. This process is the compression of the structural wood material. This publication deals with the effect of the compression on the mechanical properties of two hardwoods (beech: fagus sylvatica, oak: quercus) by the help of the three-point bending test and the Charpy impact test.


2008 ◽  
Vol 47-50 ◽  
pp. 322-325
Author(s):  
Hiroyuki Kinoshita ◽  
Koichi Kaizu ◽  
Miki Fukuda ◽  
Tokunaga Hitoo ◽  
Keisuke Koga ◽  
...  

From the viewpoint of the effective utilization of natural resources, the green composite which is produced by solidifying woodchips has been developed[1][2][3]. However, since this composite was solidified by the compressive load without the binder, the composite was very brittle and had no water resistance [4]. In this study, to improve these defects, the biodegradable resin is used as an adhesive and bamboo fibers are used as reinforced fibers. By using woodchips with two kinds of the particle size, bamboo fibers with three kinds of the length and a biodegradable adhesive, several kinds of specimens changed those mixing ratio were produced. The composite consists of the ingredients which are friendly to the environment. By the four-point bending test and Charpy impact test, the bending strength and impact strength of the composites were examined. From the experimental results, it was found that the high bending strength and high energy absorption were obtained in case where woodchips with the small particle size and long bamboo fibers were used. The proposed composite has the high strength, and the practical application is also possible.


2018 ◽  
Vol 56 (2A) ◽  
pp. 133-140
Author(s):  
Ho Ngoc Minh

In this paper, the effect  of modified nanosilica as a reinforcement agent on the performance of epoxy resin using tetrabutyl titanate (TBuT) hardener were investigated. Morphology of the epoxy/modified silica composites was determined by Scanning Electron Microscopy (SEM) method. Impact strength and flexural strength of the composites were measured by Charpy impact test and three-point bending test mode methods, respectively. Fracture toughness and fracture energy were calculated according to pre-cracked, single edge notched method with specimens in three-point bending geometry and suitable equations. The mechanical properties and fracture toughness of composites were significantly enhanced with loading nanosilica content to 5 wt.%. 


2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Madhuri Chandrashekhar Deshpande ◽  
Rajesh Chaudhari ◽  
Ramesh Narayanan ◽  
Harishwar Kale

Purpose This study aims to develop indium-based solders for cryogenic applications. Design/methodology/approach This paper aims to investigate mechanical properties of indium-based solder formulations at room temperature (RT, 27 °C) as well as at cryogenic temperature (CT, −196 °C) and subsequently to find out their suitability for cryogenic applications. After developing these alloys, mechanical properties such as tensile and impact strength were measured as per American Society for Testing and Materials standards at RT and at CT. Charpy impact test results were used to find out ductile to brittle transition temperature (DBTT). These properties were also evaluated after thermal cycling (TC) to find out effect of thermal stress. Scanning electron microscope analysis was performed to understand fracture mechanism. Results indicate that amongst the solder alloys that have been studied in this work, In-34Bi solder alloy has the best all-round mechanical properties at RT, CT and after TC. Findings It can be concluded from the results of this work that In-34Bi solder alloy has best all-round mechanical properties at RT, CT and after TC and therefore is the most appropriate solder alloy amongst the alloys that have been studied in this work for cryogenic applications Originality/value DBTT of indium-based solder alloys has not been found out in the work done so far in this category. DBTT is necessary to decide safe working temperature range of the alloy. Also the effect of TC, which is one of the major reasons of failure, was not studied so far. These parameters are studied in this work.


2016 ◽  
Vol 851 ◽  
pp. 168-172
Author(s):  
Yustiasih Purwaningrum ◽  
Triyono ◽  
Tegar Rileh Argihono ◽  
Ryan Sutrisno

Mechanical and microstructure of double side weld with various angle groove was studied in this research. LR Gr A steel plates (12 mm thickness) were welded using GMAW with corresponding 180 A, 23 V, and 20 l/min respectively with current, voltage, and gas flow. Shielding gas and filler metals used are argon and ER 70S-6. The angle groove that used were 20⁰, 40⁰ and 60⁰. The measured of mechanical properties with regard to hardness, toughness and strength using, Vickers hardness test, Charpy impact test and tensile test respectively The microstructure examined with optical microscope. The results show that the highest hardness values found in welds with groove angle 40ͦ. The transition temperatures of weld metals are at temperatures between -20°C to 0°C. Weld metals with all variations of the groove angle has a value of less than 0.1 mmpy. Microstructure of base metals and HAZ were ferrite and pearlite. While the microstructure of weld metals are accicular ferrite, grain boundary ferrite and Widmanstatten ferrite.


Author(s):  
Kobra Tajaddodi Talab ◽  
Mohd. Nordin Ibrahim ◽  
Sergey Spotar ◽  
Rosnita A. Talib ◽  
Kharidah Muhammad

Abstract Glass transition temperatures (Tg) of MR219 rice variety were measured by differential scanning calorimeter (DSC). State diagram was developed and used to evaluate drying process in this study. Glass transition temperatures range of 9.65- 61.79°C were observed for gains with moisture content of 26.8 – 7.4% (w.b.). For mechanical properties and milling test, statistical analysis was performed by using a two factor experiment in completely randomized design (CRD). Two selected factors were drying temperatures at 5 levels (40, 45, 50, 55, and 60°C) and final moisture content (FMC) at 4 levels (10-10.5, 11-11.5, 12-12.5 and 13-13.5%). Three–point bending test was applied to measure the mechanical properties of rice kernel. Generally, bending strength, apparent modulus of elasticity and fracture energy of brown rice kernel increased with decreasing the grain moisture content. Maximum bending strength was 35.69 and 33.64 MPa for 55, and 60°C, respectively. All samples that were dried at 55 and 60°C experienced to go through the glass transition line after reaching their temperature to the room temperature at the end of drying process. The effect of drying temperature, paddy FMC and their interactions on whole kernel percentage (WKP) and mechanical properties were significant (α = 0.05). An inverse relationship was observed between WKP and the percentage of strong kernels for all treatments.


2018 ◽  
Vol 7 (4.35) ◽  
pp. 258 ◽  
Author(s):  
Che Nor Aiza Jaafar ◽  
Muhammad Asyraf Muhammad Rizal ◽  
Ismail Zainol

The mechanical performance of silica modified epoxy at various concentration of sodium hydroxide for surface treatment of multi-axial kenaf has been analyzed. Epoxy resin with amine hardener was modified with silica powder at 20 phr and toughened by treated kenaf fiber that immerses in various concentrations of sodium hydroxide (NaOH) ranging from 0% to 9% of weight. The composite was analyzed through differential scanning calorimetry (DSC) to ensure complete curing process. The mechanical properties of the composites were analyzed through flexural test, Charpy impact test and DSC to ensure the complete curing process. DSC analysis results show epoxy sample was completely cured at above 73°C that verifies the curing temperature for preparation for the composite. Hence, 3% NaOH treated composite exhibits the best mechanical properties, with 10.6 kJ/m2 of impact strength, 54.1 MPa of flexural strength and 3.5 GPa of flexural modulus. It is due to the improvement of fiber-matrix compatibility. Analysis by SEM also revealed that a cleaner surface of kenaf fiber treated at 3% NaOH shown cleaner surface, thus, in turn, improve surface interaction between fiber and matrix of the composite. The composites produced in this work has high potential to be used in automotive and domestics appliances.


Author(s):  
Ying Yu ◽  
Shinichiro Kawabata ◽  
Yuqiu Yang ◽  
Hiroyuki Hamada

As well known, the corrosion resistance and durability of the material are always considered in the safety design of the materials. In this study, the jute fabric from recycled coffee bags was used to fabricate ecologically friendly composites. Jute fabrics with two kinds of different moisture contents were used to fabricate the natural fiber reinforced composites, and the hot water immersion properties have been evaluated. Additionally, the effects of the hybridization with glass woven fabric laminated structures were also investigated. Jute/Jute laminated composite, Jute/Jute/Glass, and Glass/Jute/Glass laminated hybrid composites had been fabricated by hand lay up method. A preliminary investigation on the effect of moisture contents of the jute fabric on the mechanical properties of the jute and jute/glass hybrid composites was discussed based on the results of 3 point bending test. Moreover, the durability of the composites in the hot water immersion was also evaluated. The effects of hot water immersion on the mechanical properties were investigated by the way of 3 point bending test. The specimens were immersed in hot water maintained at 80°C with the immersion time of 24, 120 and 240 hours. Specimens were taken out from the hot water at the same time and repeated the 3 point bending test after each immersion time and the weight changes had been measured. Results showed that the Jute/Jute composite absorbed water easily, and it could be noted that all of the natural dried composites showed comparable higher water absorbed value to the deeply dried ones. The bending strength after aging decreased remarkably. In particularly, all of the natural dried composites showed higher bending strength than the deeply dried one before aging. However, after 120 hours aging, on the contrary, almost the deeply dried composites showed comparable higher value to the natural dried ones. That could be due to the better bonding between fiber and matrix for the deeply dried composites which decreased the water absorption of the composites. Additionally, the hybrid structure is effective in protecting the composites from water absorbing especially for the Glass/Jute/Glass hybrid one.


2018 ◽  
Vol 68 (1) ◽  
pp. 3-15
Author(s):  
Bartosz Bienias ◽  
Wojciech Michalski ◽  
Bartosz Mielan ◽  
Krzysztof Pietryga ◽  
Elżbieta Pamuła ◽  
...  

Introduction. Acrylic resin is a basic material used in preparation of partial and complete dentures. One of the methods of improving mechanical properties of removable dentures is reinforcing acrylic resin with artificial fibers. Aim of the study. To compare mechanical properties of acrylic material reinforced with various types of glass fibers. Material and method. Heat-cured Estetic acrylic resin by Wiedent was used for denture bases. Glass mat, fiberglass fabric, long glass fibers and short glass fibers were used as reinforcing phase of the acrylic resin. In total, forty specimens were prepared, of which eight samples were controls. Research samples consisted of four groups of eight specimens each. Mechanical examinations in three-point bending test were conducted by means of the Zwick 1435 universal testing machine. Results. Specimens reinforced with short glass fibers achieved the highest values of maximum bending force (105.7 ± 8.9 N). It corresponded to the highest values of bending strength (126.8 ± 10.7 MPa). The lowest strength was found for specimens reinforced with glass mat (82.8 ± 11.8 MPa). The highest value of Young’s modulus was obtained for the samples reinforced with fiberglass fabric (3.7 ± 0.8 GPa). The highest values of deflection at maximum bending force were found for the samples reinforced with long glass fibers (4.0 ± 0.6 mm). Conclusions. The highest bending strength parameters were found for specimens reinforced with short and long glass fibers. Short glass fibers are better at improving mechanical properties of acrylic resin than long glass fibers.


Sign in / Sign up

Export Citation Format

Share Document