scholarly journals Thermographic Analysis of Composite Metallization through Cold Spray

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1860
Author(s):  
Asghar Heydari Astaraee ◽  
Antonio Salerno ◽  
Sara Bagherifard ◽  
Pierpaolo Carlone ◽  
Hetal Parmar ◽  
...  

Cold Spray is an innovative technology to create coatings through the impact of metallic particles on substrates. Its application to composites’ surfaces is recently attracting the attention of the scientific community thanks to the possibility to functionalize and improve their thermal and wear properties. Within this context, the generation of the first metal-to-composite layer is fundamental. This work presented an experimental investigation of a composite panel, reinforced with glass fibers and coated with aluminum particles. The coating investigation was carried out through active pulsed thermography, analyzing the thermal response of single and double hatches. The thermal outputs were compared with a standard microscopic analysis, with a critical discussion supporting the identification of factors that influence the thermal response to the pulse: (1) layer’s thickness; (2) cold spray coverage; (3) layer compactness; (4) particle-substrate adhesion; (5) particle’s oxidation; and (6) surface roughness.

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1602
Author(s):  
Ángel Molina-Viedma ◽  
Elías López-Alba ◽  
Luis Felipe-Sesé ◽  
Francisco Díaz

Experimental characterization and validation of skin components in aircraft entails multiple evaluations (structural, aerodynamic, acoustic, etc.) and expensive campaigns. They require different rigs and equipment to perform the necessary tests. Two of the main dynamic characterizations include the energy absorption under impact forcing and the identification of modal parameters through the vibration response under any broadband excitation, which also includes impacts. This work exploits the response of a stiffened aircraft composite panel submitted to a multi-impact excitation, which is intended for impact and energy absorption analysis. Based on the high stiffness of composite materials, the study worked under the assumption that the global response to the multi-impact excitation is linear with small strains, neglecting the nonlinear behavior produced by local damage generation. Then, modal identification could be performed. The vibration after the impact was measured by high-speed 3D digital image correlation and employed for full-field operational modal analysis. Multiple modes were characterized in a wide spectrum, exploiting the advantages of the full-field noninvasive techniques. These results described a consistent modal behavior of the panel along with good indicators of mode separation given by the auto modal assurance criterion (Auto-MAC). Hence, it illustrates the possibility of performing these dynamic characterizations in a single test, offering additional information while reducing time and investment during the validation of these structures.


Coatings ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 56
Author(s):  
Ashutosh Sharma ◽  
Byungmin Ahn

Metallic and alloyed coatings are used widely in several decorative and technology-based applications. In this work, we selected Sn coatings plated on Cu substrates for joining applications. We employed two different plating baths for the fabrication of Sn and Ni coatings: acidic stannous sulfate for Sn and Watts bath for Ni layer. The plating current densities were varied from 100–500 mA/cm2. Further, the wear and friction behavior of the coatings were studied using a ball-on-disc apparatus under dry sliding conditions. The impact of current density was studied on the morphology, wear, and coefficient of friction (COF) of the resultant coatings. The wear experiments were done at various loads from 2–10 N. The sliding distance was fixed to 7 m. The wear loss was quantified in terms of the volume of the track geometry (width and depth of the tracks). The results indicate that current density has an important role in tailoring the composition and morphology of coatings, which affects the wear properties. At higher loads (8–10 N), Sn coatings on Ni/Cu had higher volume loss with a stable COF due to a mixed adhesive and oxidative type of wear mechanism.


2021 ◽  
pp. 002199832199432
Author(s):  
Yacine Ouroua ◽  
Said Abdi ◽  
Imene Bachirbey

Multifunctional composite materials are highly sought-after by the aerospace and aeronautical industry but their performance depends on their ability to sustain various forms of damages, in particular damages due to repeated impacts. In this work we studied the mechanical behavior of a layered glass-epoxy composite with copper inserts subjected to fatigue under repeated impacts with different energy levels. Damage evolution as a function of impact energy was carefully monitored in order to determine the effect of the copper inserts on mechanical characteristics of the multifunctional composite, such as endurance and life. Results of repeated impact tests show that electric current interruption in the copper inserts occurs prior to the total perforation of the composite material, and after about 75% of the total number of impacts to failure. This is the case for the three energy levels considered in this study, [Formula: see text] = 2, 3 and 4 Joules. The epoxy resin was dissolved chemically in order to preserve the mechanical structure of the damaged copper inserts and the composite fibers for further inspection and analysis. Scanning electron microscopy (SEM) of the fractured copper inserts revealed interesting information on the nature of the damage, including information on plastic deformation, strain hardening, cracking mode, temperature increase during the impacts, and most importantly the glass fibers and their roles during the impact-fatigue tests.


2008 ◽  
Vol 74 (22) ◽  
pp. 6848-6858 ◽  
Author(s):  
F. Abram ◽  
E. Starr ◽  
K. A. G. Karatzas ◽  
K. Matlawska-Wasowska ◽  
A. Boyd ◽  
...  

ABSTRACT Sigma B (σB) is an alternative sigma factor that controls the transcriptional response to stress in Listeria monocytogenes and is also known to play a role in the virulence of this human pathogen. In the present study we investigated the impact of a sigB deletion on the proteome of L. monocytogenes grown in a chemically defined medium both in the presence and in the absence of osmotic stress (0.5 M NaCl). Two new phenotypes associated with the sigB deletion were identified using this medium. (i) Unexpectedly, the strain with the ΔsigB deletion was found to grow faster than the parent strain in the growth medium, but only when 0.5 M NaCl was present. This phenomenon was independent of the carbon source provided in the medium. (ii) The ΔsigB mutant was found to have unusual Gram staining properties compared to the parent, suggesting that σB contributes to the maintenance of an intact cell wall. A proteomic analysis was performed by two-dimensional gel electrophoresis, using cells growing in the exponential and stationary phases. Overall, 11 proteins were found to be differentially expressed in the wild type and the ΔsigB mutant; 10 of these proteins were expressed at lower levels in the mutant, and 1 was overexpressed in the mutant. All 11 proteins were identified by tandem mass spectrometry, and putative functions were assigned based on homology to proteins from other bacteria. Five proteins had putative functions related to carbon utilization (Lmo0539, Lmo0783, Lmo0913, Lmo1830, and Lmo2696), while three proteins were similar to proteins whose functions are unknown but that are known to be stress inducible (Lmo0796, Lmo2391, and Lmo2748). To gain further insight into the role of σB in L. monocytogenes, we deleted the genes encoding four of the proteins, lmo0796, lmo0913, lmo2391, and lmo2748. Phenotypic characterization of the mutants revealed that Lmo2748 plays a role in osmotolerance, while Lmo0796, Lmo0913, and Lmo2391 were all implicated in acid stress tolerance to various degrees. Invasion assays performed with Caco-2 cells indicated that none of the four genes was required for mammalian cell invasion. Microscopic analysis suggested that loss of Lmo2748 might contribute to the cell wall defect observed in the ΔsigB mutant. Overall, this study highlighted two new phenotypes associated with the loss of σB. It also demonstrated clear roles for σB in both osmotic and low-pH stress tolerance and identified specific components of the σB regulon that contribute to the responses observed.


Author(s):  
Shah Alam ◽  
Damodar Khanal

Abstract The goal of this paper is to analyze the impact behavior among geometrically different sandwich panels shown upon impact velocities. Initially, composite model with aluminum honeycomb core and Kevlar (K29) face sheets is developed in ABAQUS/Explicit and different impact velocities are applied. Keeping other parameters constant, model is simulated with T800S/epoxy face sheets. Residual velocities, energy absorption (%), and maximum deformation depth is calculated for sandwich panel for both models at five different velocities by executing finite element analysis. Once the better material is found for face sheets, process is extended by varying the ratio of front face sheet thickness to back face sheet thickness keeping other geometrical parameters constant to find the better geometry. Also, comparison of impact responses of sandwich composite panel on different ratio of front face sheet thickness to back face sheet thickness is done and validated with other results available in literature.


2014 ◽  
Vol 9 (4) ◽  
pp. 155892501400900 ◽  
Author(s):  
Sabela Camano ◽  
Nemeshwaree Behary ◽  
Philippe Vroman ◽  
Christine Campagne

Flax fibers, available as fiber bundles, are commonly used as fiber reinforcement in composite materials as a substitute for glass fibers. Pre-treatments are often necessary for improving fiber-resin adhesion, and also to facilitate fiber elementarization, and to improve fiber ability to be implemented in mechanical processes limiting fiber damages. This paper focuses on the impact of biotechnologies (effect of 2 different enzymes: a pectate lyase and a laccase) and of an ecotechnology (ultrasound with ethanol), compared to classical chemical pre-treatments (using aqueous NaOH and ammonia) on the final flax fiber bundle properties, before and after a carding process. Fiber surface properties (wettability and/or zeta potential values), fiber elementarization and mechanical properties vary with the type of treatment (chemical nature of product and conditions used). Fibers elementarised using pectate lyase and ultrasound/ethanol have a hydrophilic surface and a high water absorption capacity, and are also of highest quality in terms of increased fineness. Treatment with NaOH yields the poorest fiber bundle tenacity. Laccase enzyme yields long thick hydrophobic fibers having very low water absorption capacity, and the most neutral surface charge. Properties of flax fibers can be easily monitored using different pre-treatments resulting in fibers which would be suited for various final applications.


2013 ◽  
Vol 465-466 ◽  
pp. 962-966 ◽  
Author(s):  
Mohd Pahmi bin Saiman ◽  
Mohd Saidin Bin Wahab ◽  
Mat Uzir Wahit

To produce a good quality of dry fabric for reinforced material in a natural-based polymer composite, yarn linear density should be in consideration. A woven kenaf dry fabric with three different linear densities of 276tex, 413.4tex and 759tex were produced. The fabrics with different linear densities were been optimize with the assistance of WiseTex software. The optimized dry fabrics were infused with unsaturated polyester to produce composite panel using vacuum infusion process. The composites properties were tested on the tensile strength, flexural strength and the impact strength. The result shows that the mechanical properties of the composite increased when the yarn linear densities increased.


BJPsych Open ◽  
2021 ◽  
Vol 7 (S1) ◽  
pp. S297-S297
Author(s):  
Dominic Treloar ◽  
Soraya Mayet

AimsOpioid dependence has high risks. Opioid substitution treatment (OST) improves outcomes. Addiction specialist prescribers prescribe OST and monitor safety, but nonattendance may lead to worse outcomes. Telemedicine can reduce travel and improve attendance at appointments. Before COVID-19, we started a telemedicine in addictions trial to see if this helped in addictions. We present the qualitative patient and staff experience results.MethodHealth Research Authority approval for randomized controlled feasibility trial of Telemedicine versus Face-to-Face (control) consultations at community addictions semirural service (2500km2) using a modified Hub-and-Spoke (outreach) model. Adult opioid dependent patients prescribed OST and attending outreach were recruited. Participants received two appointments in randomized group. Telemedicine was delivered using Skype-for-business videoconferencing. Patients attended outreach, saw keyworker for drug testing first, and telemedicine conducted via keyworker's laptop. Addiction prescribers located remotely at Hub. Post-trial research interview conducted assessing patient and staff experience of Telemedicine versus Face-to-Face consultations. Data transcribed, inputted to RedCap Cloud and free-text analysed using qualitative thematic analysis.ResultOf fifty-nine patient participants, 58 completed a research interview. Patient participants reported similar levels of satisfaction between the Telemedicine and Face to Face groups. The themes generated in relation to Face-to-Face were no difference, easy, kind staff and liking being part of research. For Telemedicine, themes were less travel, good experience, easier to access, good communication, saves time and saves money. For instance, one patient stated ‘Clear, easy to access less travel’ and another patient stated ‘I struggle with travel. I found it easier’. Of 19 staff participant research interviews completed, Staff reported Good or Very Good experience with telemedicine which was equivalent for Face-to-Face consultations. Eleven staff had experience of telemedicine consultations during the trial. They reported similar themes to patients with telemedicine leading to less travel, beneficial to patient care, improves attendance and was innovative technology. One staff member reported satisfaction with telemedicine due to ‘Time, travel and money reduction’. When questioned on the downsides to telemedicine, technological issues were mainly related to connection issues and sound issues.ConclusionIn the first known RCT of Telemedicine versus Face-to-Face consultations for patients with opioid dependence attending prescriber review, we found that both patients and staff were satisfied with telemedicine as compared to face-to-face consultations. Overall themes were reduced travel, saving time and more convenience. This will be very important given the impact of COVID-19 on access to addictions services.Financial SponsorshipEast Riding CCGAcademic Health Science Network


2014 ◽  
Vol 657 ◽  
pp. 735-739 ◽  
Author(s):  
Emilian Ionut Croitoru ◽  
Gheorghe Oancea

This paper presents a method of finite element modelling used for the impact analysis of a composite panel. In this research, the composite panel consists of an oxygen mask locking panel of an aircraft. This panel is loaded with one concentrated abuse loading and three uniform distributed abuse loading cases and the stress variation within the composite panel for each load case is determined. In order to assess the impact analysis on the oxygen mask panel of the aircraft, a finite element model is created using Patran as the main application for pre/post-processing and Nastran as the main processor. The paper also presents a comparison between results obtained using the same finite element modelling of the composite panel CAD model of the panel with four load cases with different material types. The results are used to determine the most capable material stresswise.


2014 ◽  
Vol 611-612 ◽  
pp. 859-867 ◽  
Author(s):  
Awa S. Doumbia ◽  
Denis Jouannet ◽  
Thierry Falher ◽  
Laurent Cauret

In recent decades, the weight of passenger vehicles has constantly increased. This leads to a rise in fuel consumption and higher CO2 emissions. On this basis, vehicle weight reduction is a privileged research axis to meet regulatory requirements on emissions by 2020. The current study is focused on the development of thermoplastic polymer used in the automotive sector. In fact, thermoplastic polymers allow innovative design and offer the advantage of being recycled for sustainable development purposes. Some lighter fillers were incorporated in this polymer by melt processing for weight saving benefits. We were interested mainly in hollow microspheres which are lower density than conventional mineral fillers (such as: talc, calcium carbonate, glass fibers etc ...). This study explores the impact of pilot-scale melt-processing on six (6) hollow microspheres embedded in high impact polypropylene commonly used for car bumpers. We found that two commercially available microspheres (grades iM30K and K37) withstand melt-processing successfully and reduce the polymer density.


Sign in / Sign up

Export Citation Format

Share Document