scholarly journals A Robust Infrared Transducer of an Ultra-Large-Scale Array

Sensors ◽  
2020 ◽  
Vol 20 (23) ◽  
pp. 6807
Author(s):  
Defang Li ◽  
Jinying Zhang ◽  
Qingfeng Shi ◽  
Xichen Yuan ◽  
Zhuo Li ◽  
...  
Keyword(s):  
Thin Film ◽  
Large Scale ◽  
Mechanical Stability ◽  
Infrared Image ◽  
Transient Temperature ◽  
Edge Image ◽  
Micro Electro Mechanical Systems ◽  
Load Pressure ◽  
Stability Time ◽  
Film Transducer

A robust micro-electro-mechanical systems (MEMS) infrared thin film transducer of an ultra-large-scale array was proposed and fabricated on a 4-inch silicon wafer. The silicon substrate and micro cavities were introduced. This novel transducer had excellent mechanical stability, time response, and state-of-the-art pixel scale. It could bear a load of 1700 g and its load pressure was improved by more than 5.24 times and time constant decreased by 50.7% compared to the traditional soft infrared thin film transducer. The array scale of its pixels exceeded 2k × 2k. The simulation and measured results of the transient temperature and radiation intensity were well consistent. Illuminated by a 532 nm laser with a frequency of 50 Hz and 50% duty cycle, the thermal decay time of the proposed transducer was 6.0 ms. A knife-edge image was utilized for spatial resolution test and the full width at half maximum (FWHM) of the proposed transducer was 24% smaller than the traditional soft one. High-resolution infrared images were generated using the proposed robust transducer. These results proved that the robust transducer was promising in infrared image generation.

The Structure and Properties of MoSi2 Thin Film in Mos Process

1980 ◽  
Vol 38 ◽  
pp. 326-327
Author(s):  
C.K. Wu ◽  
P. Chang ◽  
N. Godinho
Keyword(s):  
Thin Film ◽  
Integrated Circuits ◽  
High Performance ◽  
Large Scale ◽  
Process Development ◽  
Structure And Properties ◽  
Metal Silicides ◽  
High Oxidation ◽  
Important Approach ◽  
High Oxidation Resistance

Recently, the use of refractory metal silicides as low resistivity, high temperature and high oxidation resistance gate materials in large scale integrated circuits (LSI) has become an important approach in advanced MOS process development (1). This research is a systematic study on the structure and properties of molybdenum silicide thin film and its applicability to high performance LSI fabrication.

scholarly journals Experimental Study on the Thickness-Dependent Hardness of SiO2 Thin Films Using Nanoindentation

Coatings ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 23
Author(s):  
Weiguang Zhang ◽  
Jijun Li ◽  
Yongming Xing ◽  
Xiaomeng Nie ◽  
Fengchao Lang ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Grain Size ◽  
Integrated Circuits ◽  
Film Thickness ◽  
Depth Range ◽  
Micro Electro Mechanical Systems ◽  
Si Substrates ◽  
Sio2 Thin Film ◽  
Average Grain Size

SiO2 thin films are widely used in micro-electro-mechanical systems, integrated circuits and optical thin film devices. Tremendous efforts have been devoted to studying the preparation technology and optical properties of SiO2 thin films, but little attention has been paid to their mechanical properties. Herein, the surface morphology of the 500-nm-thick, 1000-nm-thick and 2000-nm-thick SiO2 thin films on the Si substrates was observed by atomic force microscopy. The hardnesses of the three SiO2 thin films with different thicknesses were investigated by nanoindentation technique, and the dependence of the hardness of the SiO2 thin film with its thickness was analyzed. The results showed that the average grain size of SiO2 thin film increased with increasing film thickness. For the three SiO2 thin films with different thicknesses, the same relative penetration depth range of ~0.4–0.5 existed, above which the intrinsic hardness without substrate influence can be determined. The average intrinsic hardness of the SiO2 thin film decreased with the increasing film thickness and average grain size, which showed the similar trend with the Hall-Petch type relationship.

scholarly journals Flexible and efficient perovskite quantum dot solar cells via hybrid interfacial architecture

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Long Hu ◽  
Qian Zhao ◽  
Shujuan Huang ◽  
Jianghui Zheng ◽  
Xinwei Guan ◽  
...  
Keyword(s):  
Thin Film ◽  
Quantum Dots ◽  
Solar Cells ◽  
Quantum Dot ◽  
High Performance ◽  
Mechanical Stability ◽  
Mechanical Adhesion ◽  
Perovskite Quantum Dots ◽  
Efficient Charge ◽  
Photovoltaic Technologies

AbstractAll-inorganic CsPbI3 perovskite quantum dots have received substantial research interest for photovoltaic applications because of higher efficiency compared to solar cells using other quantum dots materials and the various exciting properties that perovskites have to offer. These quantum dot devices also exhibit good mechanical stability amongst various thin-film photovoltaic technologies. We demonstrate higher mechanical endurance of quantum dot films compared to bulk thin film and highlight the importance of further research on high-performance and flexible optoelectronic devices using nanoscale grains as an advantage. Specifically, we develop a hybrid interfacial architecture consisting of CsPbI3 quantum dot/PCBM heterojunction, enabling an energy cascade for efficient charge transfer and mechanical adhesion. The champion CsPbI3 quantum dot solar cell has an efficiency of 15.1% (stabilized power output of 14.61%), which is among the highest report to date. Building on this strategy, we further demonstrate a highest efficiency of 12.3% in flexible quantum dot photovoltaics.

scholarly journals Performance Improvement of ZnSnO Thin-Film Transistors with Low-Temperature Self-Combustion Reaction

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1099
Author(s):  
Ye-Ji Han ◽  
Se Hyeong Lee ◽  
So-Young Bak ◽  
Tae-Hee Han ◽  
Sangwoo Kim ◽  
...  
Keyword(s):  
Thin Film ◽  
Photoelectron Spectroscopy ◽  
Large Scale ◽  
Low Cost ◽  
Thermal Analyses ◽  
Thin Film Transistor ◽  
Sol Gel ◽  
Annealing Temperatures ◽  
Zinc Tin Oxide ◽  
Thermal Limitation

Conventional sol-gel solutions have received significant attention in thin-film transistor (TFT) manufacturing because of their advantages such as simple processing, large-scale applicability, and low cost. However, conventional sol-gel processed zinc tin oxide (ZTO) TFTs have a thermal limitation in that they require high annealing temperatures of more than 500 °C, which are incompatible with most flexible plastic substrates. In this study, to overcome the thermal limitation of conventional sol-gel processed ZTO TFTs, we demonstrated a ZTO TFT that was fabricated at low annealing temperatures of 350 °C using self-combustion. The optimized device exhibited satisfactory performance, with μsat of 4.72 cm2/V∙s, Vth of −1.28 V, SS of 0.86 V/decade, and ION/OFF of 1.70 × 106 at a low annealing temperature of 350 °C for one hour. To compare a conventional sol-gel processed ZTO TFT with the optimized device, thermogravimetric and differential thermal analyses (TG-DTA) and X-ray photoelectron spectroscopy (XPS) were implemented.

scholarly journals Innovative Polymeric Hybrid Nanocomposites for Application in Photocatalysis

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1184
Author(s):  
Maria Cantarella ◽  
Giuliana Impellizzeri ◽  
Alessandro Di Mauro ◽  
Vittorio Privitera ◽  
Sabrina Carola Carroccio
Keyword(s):  
Hybrid Systems ◽  
Hybrid Materials ◽  
Large Scale ◽  
Mechanical Stability ◽  
Low Cost ◽  
Atomic Layer ◽  
Hybrid Nanocomposites ◽  
Polymeric Nanocomposites ◽  
Wastewater Remediation ◽  
Antibacterial Performance

The immobilization of inorganic nanomaterials on polymeric substrates has been drawing a lot of attention in recent years owing to the extraordinary properties of the as-obtained materials. The hybrid materials, indeed, combine the benefits of the plastic matter such as flexibility, low-cost, mechanical stability and high durability, with them deriving from their inorganic counterparts. In particular, if the inorganic fillers are nanostructured photocatalysts, the originated hybrid systems will be able to utilize the energy delivered by light, catalysing chemical reactions in a sustainable pathway. Most importantly, since the nanofillers can be ad-hoc anchored to the macromolecular structure, their release in the environment will be prevented, thus overcoming one of the main restrictions that impedes their applications on a large scale. In this review, several typologies of hybrid photocatalytic nanomaterials, obtained by using both organic and inorganic semiconductors and realized with different synthetic protocols, were reported and discussed. In the first part of the manuscript, nanocomposites realized by simply blending the TiO2 or ZnO nanomaterials in thermoplastic polymeric matrices are illustrated. Subsequently, the atomic layer deposition (ALD) technique is presented as an excellent method to formulate polymeric nanocomposites. Successively, some examples of polyporphyrins hybrid systems containing graphene, acting as photocatalysts under visible light irradiation, are discussed. Lastly, photocatalytic polymeric nanosponges, with extraordinary adsorption properties, are shown. All the described materials were deeply characterized and their photocatalytic abilities were evaluated by the degradation of several organic water pollutants such as dyes, phenol, pesticides, drugs, and personal care products. The antibacterial performance was also evaluated for selected systems. The relevance of the obtained results is widely overviewed, opening the route for the application of such multifunctional photocatalytic hybrid materials in wastewater remediation.

Transient Temperature During the Vaporization of Liquid on a Pulsed Laser-Heated Solid Surface

1996 ◽  
Vol 118 (3) ◽  
pp. 702-708 ◽  
Author(s):  
H. K. Park ◽  
X. Zhang ◽  
C. P. Grigoropoulos ◽  
C. C. Poon ◽  
A. C. Tam
Keyword(s):  
Thin Film ◽  
Solid Surface ◽  
Elevated Temperatures ◽  
Bubble Nucleation ◽  
Transient Temperature ◽  
Specular Reflectance ◽  
Transient Temperature Field ◽  
Excimer Laser Pulse ◽  
Nanosecond Time Resolution ◽  
Laser Heated

The thermodynamics of the rapid vaporization of a liquid on a solid surface heated by an excimer laser pulse is studied experimentally. The transient temperature field is measured by monitoring the photothermal reflectance of an embedded thin film in nanosecond time resolution. The transient reflectivity is calibrated by considering a temperature gradient across the sample based on the static measurements of the thin film optical properties at elevated temperatures. The dynamics of bubble nucleation, growth, and collapse is detected by probing the optical specular reflectance. The metastability behavior of the liquid and the criterion for the onset of liquid–vapor phase transition in nanosecond time scale are obtained quantitatively for the first time.

A compact new-concept ellipsometer for accurate large scale thin film measurements

2014 ◽  
Vol 16 (6) ◽  
pp. 065701 ◽  
Author(s):  
Richard Koops ◽  
Petro Sonin ◽  
Marijn van Veghel ◽  
Omar El Gawhary
Keyword(s):  
Thin Film ◽  
Large Scale

Growth, Structural and Mechanical Characterization and Reliability of Chemical Vapor Deposited Co and Co3O4 Thin Films as Candidate Materials for Sensing Applications

2011 ◽  
Vol 495 ◽  
pp. 108-111 ◽  
Author(s):  
Vasiliki P. Tsikourkitoudi ◽  
Elias P. Koumoulos ◽  
Nikolaos Papadopoulos ◽  
Costas A. Charitidis
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Elastic Modulus ◽  
Data Storage ◽  
Mechanical Stability ◽  
Chemical Vapor ◽  
Magnetic Sensors ◽  
Functional Coatings ◽  
Sensing Applications ◽  
Chemical Vapor Deposited

The adhesion and mechanical stability of thin film coatings on substrates is increasingly becoming a key issue in device reliability as magnetic and storage technology driven products demand smaller, thinner and more complex functional coatings. In the present study, chemical vapor deposited Co and Co3O4thin films on SiO2and Si substrates are produced, respectively. Chemical vapor deposition is the most widely used deposition technique which produces thin films well adherent to the substrate. Co and Co3O4thin films can be used in innovative applications such as magnetic sensors, data storage devices and protective layers. The produced thin films are characterized using nanoindentation technique and their nanomechanical properties (hardness and elastic modulus) are obtained. Finally, an evaluation of the reliability of each thin film (wear analysis) is performed using the hardness to elastic modulus ratio in correlation to the ratio of irreversible work to total work for a complete loading-unloading procedure.

Sign in / Sign up

Export Citation Format

Share Document