scholarly journals Experimental Study on the Fracturing Behaviors and Mechanical Properties of Cracks under Coupled Hydro-Mechanical Effects in Rock-like Specimens

Water ◽  
2018 ◽  
Vol 10 (10) ◽  
pp. 1355 ◽  
Author(s):  
Yimeng Zhou ◽  
Cheng Zhao ◽  
Chunfeng Zhao ◽  
Chuangchuang Ma ◽  
Junfei Xie
Keyword(s):  
Mechanical Properties ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Hydraulic Pressure ◽  
External Compression ◽  
Compression Loading ◽  
Mechanical Effects ◽  
Secondary Cracks ◽  
Loading System ◽  
New Type

The artificial fracturing technique under coupled hydro-mechanical effects is widely used in many rock engineering. Therefore, the study on the fracturing behaviors and mechanical properties of hydro-mechanical coupled cracks is very crucial. In this study, a series of fracturing tests were conducted on the cylinder gypsum specimens with single pre-existing cracks using triaxial compression loading system. Water pressure was applied inside the pre-existing cracks and led to the specimen failure with external compression loading. A new type of cracks, namely horizontal coupled cracks (HCC), were found in some specimens. Macroscopic observations reveal that HCC, which were mainly caused by the hydraulic pressure, were different from any tensile wing cracks, shear secondary cracks, or shear anti-wing cracks. Subsequently, a microscopic study was performed using scanning electron microscope (SEM), the outcomes suggest that: (1) Shear fracturing zones (SFZ) and tensile fracturing zones (TFZ) under coupled hydro-mechanical effects displayed distinct characteristics on orientations, length, and independence of gypsum grains; and (2) the HCC were tensile cracks when they just initiated from outer tips of pre-existing cracks. While tensile stress made major contribution to the specimen failure during the whole fracturing processes, the HCC became tensile and shear mixed cracks when the specimen was about to fail.

scholarly journals Influence of Water Pressure on the Mechanical Properties of Concrete after Freeze-Thaw Attack under Dynamic Triaxial Compression State

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Ruijun Wang ◽  
Yan Li ◽  
Yang Li ◽  
Fan Xu ◽  
Xiaotong Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Water Pressure ◽  
Mass Loss Rate ◽  
Triaxial Compression ◽  
Ultimate Compressive Strength ◽  
Peak Strain ◽  
Freeze Thaw ◽  
Dynamic Triaxial Compression

This study aims at determining the effect of water pressure on the mechanical properties of concrete subjected to freeze-thaw (F-T) attack under the dynamic triaxial compression state. Two specimens were used: (1) a 100 mm × 100 mm × 400 mm prism for testing the loss of mass and relative dynamic modulus of elasticity (RDME) after F-T cycles and (2) cylinders with a diameter of 100 mm and a height of 200 mm for testing the dynamic mechanical properties of concrete. Strain rates ranged from 10−5·s−1 to 10−3·s−1, and F-T cycles ranged from 0 to 100. Three levels of water pressure (0, 5, and 10 MPa) were applied to concrete. Results showed that as the number of F-T cycles increased, the mass loss rate of the concrete specimen initially decreased and then increased, but the RDME decreased. Under 5 MPa of water pressure and at the same strain rate, the ultimate compressive strength decreased, whereas the peak strain increased with the increase in the number of F-T cycles. This result is contrary to the variation law of ultimate compressive strength and peak strain with the increase in strain rate under the same number of F-T times. With the increase in F-T cycles or water pressure, the strain sensitivity of the dynamic increase factor of ultimate compressive strength and peak strain decreased, respectively. After 100 F-T cycles, the dynamic compressive strength under all water pressure levels tended to increase as the strain rate increased, whereas the peak strain decreased gradually.

Experimental Research of Fine Sandstone Strength and Deformation Characteristics under Different Confining and Hydraulic Pressure

2013 ◽  
Vol 353-356 ◽  
pp. 562-570 ◽  
Author(s):  
Zai Bin Liu
Keyword(s):  
Rock Strength ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Hydraulic Pressure ◽  
Compression Tests ◽  
Exponential Relationship ◽  
Sandstone Rock ◽  
Strength And Deformation

In order to study sandstone rock strength and deformation parameters under pore water pressure conditions, triaxial compression tests of different hydraulic pressure were executed. Fitting equations of fine sandstone confining pressure and hydraulic pressure coupling effects were established. This research show that fine sandstone rock strength increases with confining pressure increases. Rock mass strength and cohesion have negative exponential relationship with hydraulic pressure. When the hydraulic pressure is 3MPa, elasticity and confining pressure fit to logarithmic relationship. Fine sandstone Elasticity modulus decreases with hydraulic pressure increases. Poisson’s ration and hydraulic pressure fit to linear relationship.

scholarly journals Experimental Study on Rock-Like Specimens with Single Flaw under Hydro-Mechanical Coupling

2019 ◽  
Vol 9 (16) ◽  
pp. 3234 ◽  
Author(s):  
Jinquan Xing ◽  
Cheng Zhao ◽  
Songbo Yu ◽  
Hiroshi Matsuda ◽  
Chuangchuang Ma
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Tensile Failure ◽  
Compression Tests ◽  
Cracking Behavior ◽  
Mechanical Coupling ◽  
High Confining Pressure

In order to study the mechanical characteristics and cracking behavior of jointed rock mass under hydro-mechanical coupling, a series of uniaxial compression tests and triaxial compression tests were carried out on cylinder gypsum specimens with a single pre-existing flaw. Under different confining pressures, water pressure was injected on the pre-existing flaw surface through a water injection channel. The geometrical morphology and tensile or shear properties of the cracks were determined by X-ray computed tomography (CT) and scanning electron microscope (SEM). Based on the macro and micro observation, nine types of cracks that caused the specimen failure are summarized. The results of mechanical properties and crack behavior showed that the confining pressure inhibited the tensile cracks, and shear failure occurred under high confining pressure. The water pressure facilitated the initiation and extension of tensile crack, which made the specimens prone to tensile failure. However, under the condition of high confining pressure and low water pressure, the lubrication effect had a significant effect on the failure pattern, under which the specimens were prone to shear failure. This experimental research on mechanical properties and cracking behavior under hydro-mechanical coupling is expected to increase its fundamental understanding.

scholarly journals Analysis of the Microstructure and Mechanical Properties of TiBw/Ti-6Al-4V Ti Matrix Composite Joint Fabricated Using TiCuNiZr Amorphous Brazing Filler Metal

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 875
Author(s):  
Hao Tian ◽  
Jianchao He ◽  
Jinbao Hou ◽  
Yanlong Lv
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Matrix Composite ◽  
Room Temperature ◽  
Filler Metal ◽  
Ceramic Fiber ◽  
Tensile Fracture ◽  
Alloy Matrix ◽  
Composite Joint ◽  
Secondary Cracks

TiB crystal whiskers (TiBw) can be synthesized in situ in Ti alloy matrix through powder metallurgy for the preparation of a new type of ceramic fiber-reinforced Ti matrix composite (TMC) TiBw/Ti-6Al-4V. In the TiBw/Ti-6Al-4V TMC, the reinforced phase/matrix interface is clean and has superior comprehensive mechanical properties, but its machinability is degraded. Hence, the bonding of reliable materials is important. To further optimize the TiBw/Ti-6Al-4V brazing technology and determine the relationship between the microstructure and tensile property of the brazed joint, results demonstrate that the elements of brazing filler metal are under sufficient and uniform diffusion, the microstructure is the typical Widmanstätten structure, and fine granular compounds in β phase are observed. The average tensile strength of the brazing specimen is 998 MPa under room temperature, which is 97.3% of that of the base metal. During the high-temperature (400 °C) tensile process, a fracture occurred at the base metal of the highest tensile test specimen with strength reaching 689 MPa, and the tensile fracture involved a combination of intergranular and transgranular modes at both room temperature and 400 °C. The fracture surface has dimples, secondary cracks are generated by the fracture of TiB whiskers, and large holes form when whole TiB whiskers are removed. The proposed algorithm provides evidence for promoting the application of TiBw/Ti-6Al-4V TMCs in practical production.

Study on mechanical properties and damage evolution of carbonaceous shale under triaxial compression with acoustic emission

2021 ◽  
pp. 105678952199119
Author(s):  
Kai Yang ◽  
Qixiang Yan ◽  
Chuan Zhang ◽  
Wang Wu ◽  
Fei Wan
Keyword(s):  
Mechanical Properties ◽  
Acoustic Emission ◽  
Water Content ◽  
Damage Evolution ◽  
Damage Assessment ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Damage Variable ◽  
Natural State ◽  
Carbonaceous Shale

To explore the mechanical properties and damage evolution characteristics of carbonaceous shale with different confining pressures and water-bearing conditions, triaxial compression tests accompanied by simultaneous acoustic emission (AE) monitoring were conducted on carbonaceous shale rock specimens. The AE characteristics of carbonaceous shale were investigated, a damage assessment method based on Shannon entropy of AE was further proposed. The results suggest that the mechanical properties of carbonaceous shale intensify with increasing confining pressure and degrade with increasing water content. Moisture in rocks does not only weaken the cohesion but also reduce the internal friction angle of carbonaceous shale. It is observed that AE activities mainly occur in the post-peak stage and the strong AE activities of saturated carbonaceous shale specimens appear at a lower normalized stress level than that of natural-state specimens. The maximum AE counts and AE energy increase with water content while decrease with confining pressure. Both confining pressure and water content induce changes in the proportions of AE dominant frequency bands, but the changes caused by confining pressure are more significant than those caused by water content. The results also indicate that AE entropy can serve as an applicable index for rock damage assessment. The damage evolution process of carbonaceous shale can be divided into two main stages, including the stable damage development stage and the damage acceleration stage. The damage variable increases slowly accompanied by a few AE activities at the first stage, which is followed by a rapid growth along with intense acoustic emission activities at the damage acceleration stage. Moreover, there is a sharp rise in the damage evolution curve for the natural-state specimen at the damage acceleration stage, while the damage variable develops slowly for the saturated-state specimen.

scholarly journals Effect of freeze–thaw cycle on physical and mechanical properties and damage characteristics of sandstone

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Longxiao Chen ◽  
Kesheng Li ◽  
Guilei Song ◽  
Deng Zhang ◽  
Chuanxiao Liu
Keyword(s):  
Mechanical Properties ◽  
Shear Failure ◽  
Triaxial Compression ◽  
Physical And Mechanical Properties ◽  
Freeze Thaw ◽  
Damage Characteristics ◽  
Large Pore ◽  
Natural Rock ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

AbstractRock deterioration under freeze–thaw cycles is a concern for in-service tunnel in cold regions. Previous studies focused on the change of rock mechanical properties under unidirectional stress, but the natural rock mass is under three dimensional stresses. This paper investigates influences of the number of freeze–thaw cycle on sandstone under low confining pressure. Twelve sandstone samples were tested subjected to triaxial compression. Additionally, the damage characteristics of sandstone internal microstructure were obtained by using acoustic emission (AE) and mercury intrusion porosimetry. Results indicated that the mechanical properties of sandstone were significantly reduced by freeze–thaw effect. Sandstone’ peak strength and elastic modulus were 7.28–37.96% and 6.38–40.87% less than for the control, respectively. The proportion of super-large pore and large pore in sandstone increased by 19.53–81.19%. We attributed the reduced sandstone’ mechanical properties to the degenerated sandstone microstructure, which, in turn, was associated with increased sandstone macropores. The macroscopic failure pattern of sandstone changed from splitting failure to shear failure with an increasing of freeze–thaw cycles. Moreover, the activity of AE signal increased at each stage, and the cumulative ringing count also showed upward trend with the increase of freeze–thaw number.

scholarly journals Study on mechanical properties of a new type of prefabricated GRC mold shell

2019 ◽  
Vol 136 ◽  
pp. 02030
Author(s):  
Chen Dong ◽  
Chen Ming ◽  
Cai Ouyang ◽  
Li Pengkun
Keyword(s):  
Mechanical Properties ◽  
Production Process ◽  
Cross Section ◽  
Stress System ◽  
Research Results ◽  
Floor Space ◽  
Section Size ◽  
Speed Up ◽  
New Type ◽  
Prefabricated Building

The GRC formwork structural column adopts the factory-based vertical prefabrication production process, which can reduce the floor space, reduce the formwork loss, speed up the construction progress, promote the full decoration of the prefabricated building, and improve the efficiency of the assembly construction. major. In order to optimize the production process of prefabricated GRC formwork column, the overall stress system of GRC formwork structure is analyzed in the concrete pouring process, and the thickness of GRC formwork, the number of steel hoops and the GRC mode are considered. The influence of the shell cross-section size on the mechanical properties. The research results can provide reference for the optimization and design of prefabricated GRC formwork column production process.

scholarly journals Mechanical behaviour of calcareous waste under consolidated drained triaxial compression testing in saturated conditions

2019 ◽  
Vol 106 ◽  
pp. 01016
Author(s):  
Jakub Zięba
Keyword(s):  
Mechanical Behaviour ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Soil Samples ◽  
Excess Pore Water Pressure ◽  
Stiffness Properties ◽  
Construction Purpose ◽  
Strength And Stiffness ◽  
Excess Pore

The article presents the mechanical behaviour of calcareous waste under consolidated and drained condition in Triaxial compression test (CD). The host material currently being considered for the construction purpose of several buildings in Poland. One of the location of calcareous waste is in Łagiewniki area (in Cracow) [1,2]. In this work, particular attention has been paid to the to ensure fully saturation for all the tested soil samples and avoid generation of unwanted excess pore water pressure during shearing stage. The saturation level of soil samples was estimated based on Skempton’s law (B>0.95). CD Triaxial test have been conducted in order to derive information on its strength and stiffness properties.

Sign in / Sign up

Export Citation Format

Share Document