Research on the Motion Model of Flying Plate in Explosive Welding

2010 ◽  
Vol 108-111 ◽  
pp. 1152-1157
Author(s):  
Ming Lu ◽  
Liu Peng ◽  
Ling Li ◽  
Xin Wei Ji
Keyword(s):  
Explosive Welding ◽  
Maximum Speed ◽  
Metallic Materials ◽  
Motion Model ◽  
Experiment Data ◽  
Constant Acceleration ◽  
Acceleration Model ◽  
Calculated Curve ◽  
The Relationship ◽  
Good Agreement

Constant variably acceleration motion model of flying plate is proposed and the model formula about the relationship between speed of flying plate and clearance is put forward, which provides theorotical basis for choosing optimum clearance by collision speed of different metallic materials in explosive welding industry production. High pressure impulse X radial photograph experiment was carried out, the photos of the flying stances of flying plate in different clearances were obtained and the corresponding flying speeds of flying plate were calculated. Curve fitting of the experiment data through constant variably acceleration motion model was carried out. The results show that constant variably acceleration motion model accords well with the experiment data，and the maximum speed of flying plate calculated through constant acceleration model is in good agreement with the values through theoretical calculation. Therefore, it is concluded that the motion of flying plate in the main follows the constant variably acceleration motion.

NUMERICAL MODEL TO SIMULATE THE EROSION ON THE SLOPE DUE TO OVERTOPPING

2010 ◽  
Vol 13 (3) ◽  
pp. 78-87
Author(s):  
Hoai Cong Huynh
Keyword(s):  
Numerical Model ◽  
Flow Model ◽  
Bed Load ◽  
Experiment Data ◽  
Step Method ◽  
Morphological Model ◽  
Load Transport ◽  
Bed Load Transport ◽  
The Finite Difference Method ◽  
Good Agreement

The numerical model is developed consisting of a 1D flow model and the morphological model to simulate the erosion due to the water overtopping. The step method is applied to solve the water surface on the slope and the finite difference method of the modified Lax Scheme is applied for bed change equation. The Meyer-Peter and Muller formulae is used to determine the bed load transport rate. The model is calibrated and verified based on the data in experiment. It is found that the computed results and experiment data are good agreement.

Temperature Influence on Performance of Oxidation Ponds

1991 ◽  
Vol 24 (5) ◽  
pp. 85-96 ◽  
Author(s):  
Qingliang Zhao ◽  
Zijie Zhang
Keyword(s):  
Mathematical Model ◽  
Temperature Influence ◽  
Field Scale ◽  
Experiment Data ◽  
Computer Technique ◽  
Oxidation Pond ◽  
Optimum Model ◽  
Oxidation Ponds ◽  
The Mathematical Model ◽  
The Relationship

By means of simulated tests of a laboratory–scale oxidation pond model, the relationship between BOD5 and temperature fluctuation was researched. Mathematical modelling for the pond's performance and K1determination were systematically described. The calculation of T–K1–CeCe/Ci) was complex but the problem was solved by utilizing computer technique in the paper, and the mathematical model which could best simulate experiment data was developed. On the basis of experiment results,the concept of plug–ratio–coefficient is also presented. Finally the optimum model recommended here was verified with the field–scale pond data.

scholarly journals Experimental studies on the transformation from firn to ice in the wet-snow zone of temperate glaciers

1997 ◽  
Vol 24 ◽  
pp. 181-185 ◽  
Author(s):  
Katsuhisa Kawashima ◽  
Tomomi Yamada
Keyword(s):  
Experimental Studies ◽  
Ice Formation ◽  
Compression Tests ◽  
Densification Rate ◽  
Overburden Pressure ◽  
Proportionality Constant ◽  
Wet Snow ◽  
Water Saturated ◽  
The Relationship ◽  
Good Agreement

The densification of water-saturated firn, which had formed just above the firn-ice transition in the wet-snow zone of temperate glaciers, was investigated by compression tests under pressures ranging from 0.036 to 0.173 MPa, with special reference to the relationship between densification rate, time and pressure. At each test, the logarithm of the densification rate was proportional to the logarithm of the time, and its proportionality constant increased exponentially with increasing pressure. The time necessary for ice formation in the firn aquifer was calculated using the empirical formula obtained from the tests. Consequently, the necessary time decreased exponentially as the pressure increased, which shows that the transformation from firn in ice can be completed within the period when the firn aquifer exists, if the overburden pressure acting on the water-saturated firn is above 0.12–0.14 MPa. This critical value of pressure was in good agreement with the overburden pressure obtained from depth–density curves of temperate glaciers. It was concluded that the depth of firn–ice transition was self-balanced by the overburden pressure to result in the concentration between 20 and 30 m.

Investigation of Residual Strains of the Second Kind in Plastically Deformed Metallic Materials

1994 ◽  
Vol 376 ◽  
Author(s):  
M. Vrána ◽  
P. Klimanek ◽  
T. Kschidock ◽  
P. Lukáš ◽  
P. Mikula
Keyword(s):  
High Resolution ◽  
Neutron Diffraction ◽  
Stacking Faults ◽  
Metallic Materials ◽  
Line Broadening ◽  
X Ray Diffraction ◽  
X Ray ◽  
Neutron Diffractometer ◽  
Residual Strains ◽  
Good Agreement

ABSTRACTInvestigation of strongly distorted crystal structures caused by dislocations, stacking-faults etc. in both plastically deformed f.c.c. and b.c.c. metallic materials was performed by the analysis of the neutron diffraction line broadening. Measurements were realized by means of the high resolution triple-axis neutron diffractometer equipped by bent Si perfect crystals as monochromator and analyzer at the NPI Řež. The substructure parameters obtained in this manner are in good agreement with the results of X-ray diffraction analysis.

Estimation of Interlayer Thickness in Inorganic Particulate-Filled Polymer Composites

2011 ◽  
Vol 24 (6) ◽  
pp. 777-788 ◽  
Author(s):  
J.Z. Liang
Keyword(s):  
Polymer Composites ◽  
Volume Fraction ◽  
Particle Diameter ◽  
Interfacial Structure ◽  
Interlayer Thickness ◽  
Filled Polymer ◽  
Mechanical And Physical Properties ◽  
The Relationship ◽  
Good Agreement

The structure of the interlayer between matrix and inclusions affect directly the mechanical and physical properties of inorganic particulate-filled polymer composites. The interlayer thickness is an important parameter for characterization of the interfacial structure. The effects of the interlayer between the filler particles and matrix on the mechanical properties of polymer composites were analyzed in this article. On the basis of a simplified model of interlayer, an expression for estimating the interlayer thickness ([Formula: see text]) was proposed. In addition, the relationship between the [Formula: see text] and the particle size and its concentration was discussed. The results showed that the calculations of the [Formula: see text] and thickness/particle diameter ratio ([Formula: see text]) increased nonlinearly with an increase of the volume fraction of the inclusions. Moreover, the predictions of [Formula: see text] and the relevant data reported in literature were compared, and good agreement was found between them.

TCAD Study of the Raised SiGe Source/Drain in 40nm PMOS

2015 ◽  
Vol 645-646 ◽  
pp. 70-74 ◽  
Author(s):  
Min Zhong ◽  
Yu Hang Zhao ◽  
Shou Mian Chen ◽  
Ming Li ◽  
Shao Hai Zeng ◽  
...  
Keyword(s):  
Computer Aided Design ◽  
Critical Role ◽  
Sige Layer ◽  
Strain Engineering ◽  
Effect Transistor ◽  
Simulation Results ◽  
Aided Design ◽  
The Relationship ◽  
Growth Experiments ◽  
Good Agreement

An embedded SiGe layer was applied in the source/drain areas (S/D) of a field-effect transistor to boost the performance in the p channels. Raised SiGe S/D plays a critical role in strain engineering. In this study, the relationship between the SiGe overfilling and the enhancement of channel stress was investigated. Systematic technology computer aided design (TCAD) simulations of the SiGe overfill height in a 40 nm PMOS were performed. The simulation results indicate that a moderate SiGe overfilling induces the highest stress in the channel. Corresponding epitaxial growth experiments were done and the obtained experimental data was in good agreement with the simulation results. The effect of the SiGe overfilling is briefly discussed. The results and conclusions presented within this paper might serve as useful references for the optimization of the embedded SiGe stressor for 40 nm logic technology node and beyond.

Phase stability, Debye temperature and hardness of semiconducting manganese tetraboride MnB4: First-principles investigations

2017 ◽  
Vol 31 (20) ◽  
pp. 1750131 ◽  
Author(s):  
Ming-Min Zhong ◽  
Cheng Huang ◽  
Chun-Ling Tian
Keyword(s):  
Debye Temperature ◽  
Phase Stability ◽  
First Principles ◽  
Formation Enthalpy ◽  
Structural Features ◽  
High Melting Point ◽  
Fundamental Understanding ◽  
New Perspective ◽  
The Relationship ◽  
Good Agreement

First-principles investigations are employed to provide a fundamental understanding of the structural features, phase stability, mechanical properties, Debye temperature, and hardness of manganese tetraboride. Eight candidate structures of known transition-metal tetraborides are chosen to probe. The calculated lattice parameters, elastic properties, Poisson’s ratio, and [Formula: see text] ratio are derived. It is observed that the monoclinic structure with [Formula: see text] symmetry (MnB4–MnB4) is the most stable in energy. The mechanical and thermodynamic stabilities of seven possible phases are confirmed by the calculated elastic constants and formation enthalpy. Moreover, the analysis on density of states demonstrates semiconducting behavior of MnB4–MnB4 and different metallic behaviors of other phases. The estimated hardness of MnB4–MnB4 is 38.3 GPa, which is in good agreement with experimental value. Furthermore, the relationship between hardness and Debye temperature is investigated and verifies that MnB4–MnB4 is a newly potential semiconducting ultrahard material with high melting point. It provides a new perspective of searching for semiconducting superhard materials to be applied in extreme conditions.

Comparative Calculations of TROI TS-2 and TS-3 Steam Explosion Experiments With TEXAS-V

2017 ◽  
Author(s):  
Taehoon Kim ◽  
Sukyoung Pak ◽  
Yongjin Cho
Keyword(s):  
Void Fraction ◽  
Steam Explosion ◽  
Peak Pressure ◽  
Severe Accident ◽  
Experiment Data ◽  
Trigger Time ◽  
Vessel Reactor ◽  
The Moment ◽  
Containment Integrity ◽  
Good Agreement

During a severe accident, contact of the molten corium with the coolant water may cause an energetic steam explosion which is a rapid increase of explosive vaporization by transfer to the water of a significant part of the energy in the corium melt. This steam explosion has been considered as an adverse effect when the water is used to cool the molten corium and could threaten reactor vessel, reactor cavity, containment integrity. In this study, TROI TS-2 and TS-3 experiments as part of the OECD/SERENA-2 project were analyzed with TEXAS-V. Input parameters were based on actual TROI experiment data. In mixing simulations, calculated results were compared to melt front behavior, void fraction in trigger time and other parameters in experiment results. In explosion simulations, corresponding to TROI experiments an external triggering was employed at the moment that melt front reached heights of 0.4 m. Calculated results of peak pressure and impulse at the bottom were compared with TROI experiment results. Melt front behaviors of the melt was different from the experimental results in both TS-2 and TS-3. Void fraction in triggering time in TS-2 was in good agreement with the experiment results and in TS-3 was slightly overestimated. The peak pressure and impulse at bottom were successfully predicted by TEXAS-V. These calculations will allow establishing whether the limitations and differences observed in the simulations of the experiments are important for the reactor case.

Estimating the influence of temperature on the survival of chinook salmon smolts (Oncorhynchus tshawytscha) migrating through the Sacramento – San Joaquin River Delta of California

1995 ◽  
Vol 52 (4) ◽  
pp. 855-863 ◽  
Author(s):  
Peter Fritz Baker ◽  
Franklin K. Ligon ◽  
Terence P. Speed
Keyword(s):  
Water Temperature ◽  
Chinook Salmon ◽  
Oncorhynchus Tshawytscha ◽  
Logistic Function ◽  
Laboratory Findings ◽  
Natural Systems ◽  
San Joaquin River ◽  
Influence Of Temperature On ◽  
The Relationship ◽  
Good Agreement

Data from the U.S. Fish and Wildlife Service are used to investigate the relationship between water temperature and survival of hatchery-raised fall-run chinook salmon (Oncorhynchus tshawytscha) smolts migrating through the Sacramento – San Joaquin Delta of California. A formal statistical model is presented for the release of smolts marked with coded-wire tags (CWTs) in the lower Sacramento River and the subsequent recovery of marked smolts in midwater trawls in the Delta. This model treats survival as a logistic function of water temperature, and the release and recovery of different CWT groups as independent mark–recapture experiments. Iteratively reweighted least squares is used to fit the model to the data, and simulation is used to establish confidence intervals for the fitted parameters. A 95% confidence interval for the upper incipient lethal temperature, inferred from the trawl data by this method, is 23.01 ± 1.08 °C This is in good agreement with published experimental results obtained under controlled conditions (24.3 ± 0.1 and 25.1 ± 0.1 °C for chinook salmon acclimatized to 10 and 20 °C, respectively): this agreement has implications for the applicability of laboratory findings to natural systems.

scholarly journals The Effects of Incident Turbulence and Moving Wakes on Laminar Heat Transfer in Gas Turbines

1992 ◽  
Author(s):  
K. Dullenkopf ◽  
R. E. Mayle
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Gas Turbines ◽  
Free Stream ◽  
Cross Flow ◽  
Turbulence Parameter ◽  
Constant Acceleration ◽  
Free Stream Turbulence ◽  
Laminar Boundary Layers ◽  
Good Agreement

The effect of free-stream turbulence and moving wakes on augmenting heat transfer in accelerating laminar boundary layers is considered. First, the the effect of free-stream turbulence is re-examined in terms of a Nusselt number and turbulence parameter which correctly account for the free-stream acceleration and a correlation for both cylinders in cross flow and airfoils with regions of constant acceleration is obtained. This correlation is then used in a simple quasi-steady model to predict the effect of periodically passing wakes on airfoil laminar heat transfer. A comparison of the predictions with measurements shows good agreement.

Sign in / Sign up

Export Citation Format

Share Document