Properties of VA/E/MMA Terpolymer Powder-Modified Mortars

2015 ◽  
Vol 1129 ◽  
pp. 169-176
Author(s):  
Sunhee Hong ◽  
Wan Ki Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cement Mortar ◽  
Mercury Porosimetry ◽  
Chloride Ion ◽  
Test Results ◽  
Polymer Powder ◽  
Chloride Ion Penetration ◽  
Redispersible Polymer Powder

This study is to examine and clarify the quality of polymer-modified mortars using a VA/E/MMA terpolymer powder as compared with polymer-modified mortars using a VAE copolymer powder. Polymer-modified mortars using general commercial redispersible polymer powders are prepared with various polymer-cement ratios, and tested for flexural and compressive strengths, tensile strength, water absorption, chloride ion penetration, carbonation and pore size distribution by mercury porosimetry. Overall, the properties of polymer-modified mortars using a VA/E/MMA terpolymer powder were superior to those of polymer-modified mortars using a VAE copolymer powder. And VA/E/MMA terpolymer powder-modified mortars showed significantly improved mechanical properties and durability in comparison with unmodified mortar. It is concluded from the test results that the modification of cement mortar with redispersible polymer powder improves the properties of unmodified mortar, and VA/E/MMA terpolymer powder has higher quality than VAE copolymer powder.

scholarly journals Strength, Carbonation Resistance, and Chloride-Ion Penetrability of Cement Mortars Containing Catechol-Functionalized Chitosan Polymer

Materials ◽  
2021 ◽  
Vol 14 (21) ◽  
pp. 6395
Author(s):  
Se-Jin Choi ◽  
Sung-Ho Bae ◽  
Jae-In Lee ◽  
Eun Ji Bang ◽  
Haye Min Ko
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Cement Mortar ◽  
Control Sample ◽  
Drying Shrinkage ◽  
Chloride Ion ◽  
Total Charge ◽  
Polymer Mixtures ◽  
Carbonation Resistance

There have been numerous recent studies on improving the mechanical properties and durability of cement composites by mixing them with functional polymers. However, research into applying modified biopolymer such as catechol-functionalized chitosan to cement mortar or concrete is rare to the best of our knowledge. In this study, catechol-functionalized chitosan (Cat-Chit), a well-known bioinspired polymer that imitates the basic structures and functions of living organisms and biological materials in nature, was synthesized and combined with cement mortar in various proportions. The compressive strength, tensile strength, drying shrinkage, accelerated carbonation depth, and chloride-ion penetrability of these mixes were then evaluated. In the ultraviolet–visible spectra, a maximum absorption peak appeared at 280 nm, corresponding to catechol conjugation. The sample containing 7.5% Cat-Chit polymer in water (CPW) exhibited the highest compressive strength, and its 28-day compressive strength was ~20.2% higher than that of a control sample with no added polymer. The tensile strength of the samples containing 5% or more CPW was ~2.3–11.5% higher than that of the control sample. Additionally, all the Cat-Chit polymer mixtures exhibited lower carbonation depths than compared to the control sample. The total charge passing through the samples decreased as the amount of CPW increased. Thus, incorporating this polymer effectively improved the mechanical properties, carbonation resistance, and chloride-ion penetration resistance of cement mortar.

scholarly journals Quality of Surface Texture and Mechanical Properties of PLA and PA-Based Material Reinforced with Carbon Fibers Manufactured by FDM and CFF 3D Printing Technologies

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1671
Author(s):  
Mohd Shahneel Saharudin ◽  
Jiri Hajnys ◽  
Tomasz Kozior ◽  
Damian Gogolewski ◽  
Paweł Zmarzły
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Surface Layer ◽  
3D Printing ◽  
Carbon Fibers ◽  
Tensile Tests ◽  
Mechanical Tests ◽  
Uniaxial Tensile ◽  
Test Results

The paper presents the results of mechanical tests of models manufactured with two 3D printing technologies, FDM and CFF. Both technologies use PLA or PA-based materials reinforced with carbon fibers. The work includes both uniaxial tensile tests of the tested materials and metrological measurements of surfaces produced with two 3D printing technologies. The test results showed a significant influence of the type of technology on the strength of the models built and on the quality of the technological surface layer. After the analysis of the parameters of the primary profile, roughness and waviness, it can be clearly stated that the quality of the technological surface layer is much better for the models made with the CFF technology compared to the FDM technology. Furthermore, the tensile strength of the models manufactured of carbon fiber-enriched material is much higher for samples made with CFF technology compared to FDM.

scholarly journals The Influence of Different Plasma Cell Discharges on the Performance Quality of Surgical Gown Samples

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4329
Author(s):  
Atif H. Asghar ◽  
Ahmed Rida Galaly
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Exposure Time ◽  
Electrical Characteristics ◽  
Cathode Fall ◽  
Treatment Efficiency ◽  
Performance Quality ◽  
Surgical Gown ◽  
The One

An experimental study was performed on a low-density plasma discharge using two different configurations of the plasma cell cathode, namely, the one mesh system electrodes (OMSE) and the one mesh and three system electrodes (OMTSE), to determine the electrical characteristics of the plasma such as current–voltage characteristics, breakdown voltage (VB), Paschen curves, current density (J), cathode fall thickness (dc), and electron density of the treated sample. The influence of the electrical characteristics of the plasma fluid in the cathode fall region for different cathode configuration cells (OMSE and OMTSE) on the performance quality of a surgical gown was studied to determine surface modification, treatment efficiency, exposure time, wettability property, and mechanical properties. Over a very short exposure time, the treatment efficiency for the surgical gown surface of plasma over the mesh cathode at a distance equivalent to the cathode fall distance dc values of the OMTSE and for OMSE reached a maximum. The wettability property decreased from 90 to 40% for OMTSE over a 180 s exposure time and decreased from 90 to 10% for OMSE over a 160 s exposure time. The mechanisms of each stage of surgical gown treatment by plasma are described. In this study, the mechanical properties of the untreated and treated surgical gown samples such as the tensile strength and elongation percentage, ultimate tensile strength, yield strength, strain hardening, resilience, toughness, and fracture (breaking) point were studied. Plasma had a more positive effect on the mechanical properties of the OMSE reactor than those of the OMTSE reactor.

Preparation Techniques and Property Evaluations of Highly Air Permeable Needle-Punched Geotextiles

2015 ◽  
Vol 749 ◽  
pp. 278-281
Author(s):  
Jia Horng Lin ◽  
Jing Chzi Hsieh ◽  
Jin Mao Chen ◽  
Wen Hao Hsing ◽  
Hsueh Jen Tan ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Service Life ◽  
Mechanical Strength ◽  
Pore Structure ◽  
Test Results ◽  
Needle Punching ◽  
Pet Fibers ◽  
Environmental Requirements ◽  
Preparation Techniques

Geotextiles are made of polymers, and their conjunction with different processes and materials can provide geotextiles with desirable characteristics and functions, such as filtration, separation, and drainage, and thereby meets the environmental requirements. Chemical resistant and mechanical strong polymers, including polyester (PET) and polypropylene (PP), are thus used to prolong the service life of the products made by such materials. This study proposes highly air permeable geotextiles that are made with different thicknesses and various needle punching speeds, and the influences of these two variables over the pore structure and mechanical properties are then examined. PET fibers, PP fibers, and recycled Kevlar fibers are blended, followed by being needle punched with differing spaces and speeds to form geotextiles with various thicknesses and porosities. The textiles are then evaluated for their mechanical strength and porosity. The test results show that a thickness of 4.5 cm and 1.5 cm demonstrate an influence on the tensile strength of the geotextiles, which is ascribed to the webs that are incompletely needle punched. However, the excessive needle punching speed corresponding to a thickness of 0.2 cm results in a decrease in tensile strength, but there is also an increase in the porosity of the geotextiles.

scholarly journals The Influence of the Asymmetric Arb Process on the Properties of Al-Mg-Al Multi-Layer Sheets / Wpływ Asymetrii W Procesie Arb Na Właściwości Wielowarstwowych Blach Al-Mg-Al

2015 ◽  
Vol 60 (4) ◽  
pp. 2821-2826 ◽  
Author(s):  
A. Wierzba ◽  
S. Mróz ◽  
P. Szota ◽  
A. Stefanik ◽  
R. Mola
Keyword(s):  
Mechanical Properties ◽  
Experimental Study ◽  
Tensile Strength ◽  
Rolling Process ◽  
Asymmetry Factor ◽  
Relative Reduction ◽  
Test Results ◽  
Initial Thickness ◽  
Asymmetric Rolling ◽  
Aluminium Layer

The paper presents the results of the experimental study of the three-layer Al-Mg-Al sheets rolling process by the ARB method. The tests carried out were limited to single-pass symmetric and asymmetric rolling processes. An Al-Mg-Al package with an initial thickness of 4 mm (1-2-1 mm) was subjected to the process of rolling with a relative reduction of 50%. To activate the shear band in the strip being deformed, an asymmetry factor of av=2 was applied. From the test results, an increase in the tensile strength of the multi-layer Al-Mg-Al sheets obtained from the asymmetric process was observed. Microhardness tests did not show any significant differences in aluminium layer between respective layers of sheets obtained from the symmetric and the asymmetric process. By contrast, for the magnesium layer, an increase in microhardness from 72 HV to 79 HV could be observed for the asymmetric rolling. The analysis of the produced Al-Mg-Al sheets shows that the good bond between individual layers and grain refinement in the magnesium layer contributed to the obtaining of higher mechanical properties in the multi-layer sheets produced in the asymmetric process compared to the sheets obtained from the symmetric process.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

scholarly journals Effect of High-Dispersible Graphene on the Strength and Durability of Cement Mortars

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 915
Author(s):  
Xiaoqiang Qi ◽  
Sulei Zhang ◽  
Tengteng Wang ◽  
Siyao Guo ◽  
Rui Ren
Keyword(s):  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Cement Mortar ◽  
Chloride Ion ◽  
Cementitious Materials ◽  
Chloride Ion Penetration ◽  
Cement Mortars ◽  
Strength And Durability ◽  
Durability Performance

Graphene’s outstanding properties make it a potential material for reinforced cementitious composites. However, its shortcomings, such as easy agglomeration and poor dispersion, severely restrict its application in cementitious materials. In this paper, a highly dispersible graphene (TiO2-RGO) with better dispersibility compared with graphene oxide (GO) is obtained through improvement of the graphene preparation method. In this study, both GO and TiO2-RGO can improve the pore size distribution of cement mortars. According to the results of the mercury intrusion porosity (MIP) test, the porosity of cement mortar mixed with GO and TiO2-RGO was reduced by 26% and 40%, respectively, relative to ordinary cement mortar specimens. However, the TiO2-RGO cement mortars showed better pore size distribution and porosity than GO cement mortars. Comparative tests on the strength and durability of ordinary cement mortars, GO cement mortars, and TiO2-RGO cement mortars were conducted, and it was found that with the same amount of TiO2-RGO and GO, the TiO2-RGO cement mortars have nearly twice the strength of GO cement mortars. In addition, it has far higher durability, such as impermeability and chloride ion penetration resistance, than GO cement mortars. These results indicate that TiO2-RGO prepared by titanium dioxide (TiO2) intercalation can better improve the strength and durability performance of cement mortars compared to GO.

scholarly journals Preparation and Mechanical Properties of Graphene Oxide: Cement Nanocomposites

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Fakhim Babak ◽  
Hassani Abolfazl ◽  
Rashidi Alimorad ◽  
Ghodousi Parviz
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Graphene Oxide ◽  
Cement Mortar ◽  
Cement Matrix ◽  
Cement Composites ◽  
Xrd Diffraction ◽  
Calcium Silicate Hydrates ◽  
The Matrix ◽  
Scanning Electron

We investigate the performance of graphene oxide (GO) in improving mechanical properties of cement composites. A polycarboxylate superplasticizer was used to improve the dispersion of GO flakes in the cement. The mechanical strength of graphene-cement nanocomposites containing 0.1–2 wt% GO and 0.5 wt% superplasticizer was measured and compared with that of cement prepared without GO. We found that the tensile strength of the cement mortar increased with GO content, reaching 1.5%, a 48% increase in tensile strength. Ultra high-resolution field emission scanning electron microscopy (FE-SEM) used to observe the fracture surface of samples containing 1.5 wt% GO indicated that the nano-GO flakes were well dispersed in the matrix, and no aggregates were observed. FE-SEM observation also revealed good bonding between the GO surfaces and the surrounding cement matrix. In addition, XRD diffraction data showed growth of the calcium silicate hydrates (C-S-H) gels in GO cement mortar compared with the normal cement mortar.

The Effect of Yarn Linear Density on Mechanical Properties of Plain Woven Kenaf Reinforced Unsaturated Polyester Composite

2013 ◽  
Vol 465-466 ◽  
pp. 962-966 ◽  
Author(s):  
Mohd Pahmi bin Saiman ◽  
Mohd Saidin Bin Wahab ◽  
Mat Uzir Wahit
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Linear Density ◽  
Unsaturated Polyester ◽  
Composite Panel ◽  
Composite Yarn ◽  
Polyester Composite ◽  
The Impact ◽  
Woven Kenaf

To produce a good quality of dry fabric for reinforced material in a natural-based polymer composite, yarn linear density should be in consideration. A woven kenaf dry fabric with three different linear densities of 276tex, 413.4tex and 759tex were produced. The fabrics with different linear densities were been optimize with the assistance of WiseTex software. The optimized dry fabrics were infused with unsaturated polyester to produce composite panel using vacuum infusion process. The composites properties were tested on the tensile strength, flexural strength and the impact strength. The result shows that the mechanical properties of the composite increased when the yarn linear densities increased.

Ultra-Low Cement Dosage Hill Sand Concrete’s Electric Flux and Carbonization Performance Study

2014 ◽  
Vol 584-586 ◽  
pp. 1332-1336
Author(s):  
Wei Wei Hu ◽  
Li Bin Xu ◽  
Yi Dong ◽  
Xiao Peng Nie
Keyword(s):  
Materials Science ◽  
Chloride Ion ◽  
Social Stability ◽  
Concrete Durability ◽  
Test Results ◽  
Performance Study ◽  
Chloride Ion Penetration ◽  
Concrete Materials ◽  
Electric Flux ◽  
Low Dosage

Concrete durability is closely related to the national economy and social stability, environmental protection, sustainable development is a major research topic concrete materials science, engineering and technological problems are a major concern. This paper studies resistance to chloride Ion penetration performance and anti-carbonation of low cement concrete sand hill. And combined with the test results analysis and discussion the low dosage of cement to sand concrete electric flux and the influence of carbonization resistance.

Sign in / Sign up

Export Citation Format

Share Document