Numerical Simulations on Assembly Modifications for Annular Casing of One Centrifugal Pump

2012 ◽  
Vol 516-517 ◽  
pp. 966-969
Author(s):  
Yi Zhang Fan ◽  
Zhi Gang Zuo ◽  
Shu Hong Liu ◽  
Yu Jun Sha ◽  
Yu Lin Wu
Keyword(s):  
Numerical Simulation ◽  
High Pressure ◽  
High Temperature ◽  
Numerical Simulations ◽  
Centrifugal Pump ◽  
Radial Force ◽  
Hydraulic Efficiency ◽  
Centrifugal Pumps ◽  
Safety Factors ◽  
Simulation Results

Centrifugal pumps adopt annular casings instead of volute casings when working in high temperature and high pressure conditions, which results in conservative safety factors in sacrifice of hydraulic efficiency. This paper presents numerical simulations on two assembly modification methods for one annular casing imitating the volute casing to improve hydraulic performance. Method one was the eccentric axis method. Method two was the extended vane method. Numerical simulation results, given by CFX, showed that both the two method could increase the hydraulic efficiency and head while rise in radial force was small.

Numerical Simulation Study of the Impellers of the Centrifugal Pump Based on Different Turbulence Models

2013 ◽  
Vol 423-426 ◽  
pp. 2049-2053 ◽  
Author(s):  
Ao Hui Guo ◽  
Yong Zhong Zeng ◽  
Xiao Bing Liu
Keyword(s):  
Numerical Simulation ◽  
Flow Field ◽  
Centrifugal Pump ◽  
Simulation Study ◽  
Turbulence Models ◽  
Centrifugal Pumps ◽  
Ansys Software ◽  
Sst Model ◽  
Simulation Results ◽  
Actual Test

The Computational Fluid (CFD) technology has been successfully used in the numerical simulation of the turbulent flow of centrifugal pump.In this article , we carry on the experiment by using uses ANSYS software,based on the standard k-ε model, SST model and BSL model , to get the the flow field of the numerical simulationof the impeller .We found that the simulation results and the actual results are different under different turbulence models. Then we can draw out the Q-η curve and compare it with the actual test data.Compared with other turbulence models, The SST model is more suitable for the models of centrifugal pumps in the article.Furthermore,we list the pressure contours and velocity vectors for pumps discussed in the paper under the optimal model.The process can provide a theoretical reference for the optimization and further study of the centrifugal pump in the future.

scholarly journals Experiment and simulation about the effect of wear-ring abrasion on the performance of a marine centrifugal pump

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199811
Author(s):  
Wu Xianfang ◽  
Du Xinlai ◽  
Tan Minggao ◽  
Liu Houlin
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Pressure Pulsation ◽  
Vibration Velocity ◽  
Test Results ◽  
Obvious Effect ◽  
Performance Change ◽  
Pump Test ◽  
Simulation Results ◽  
Axis Passing

The wear-ring abrasion can cause performance degradation of the marine centrifugal pump. In order to study the effect of front and back wear-ring clearance on a pump, test and numerical simulation were used to investigate the performance change of a pump. The test results show that the head and efficiency of pump decrease by 3.56% and 9.62% respectively at 1.0 Qd due to the wear-ring abrasion. Under 1.0 Qd, with the increase of the front wear-ring the vibration velocity at pump foot increases from 0.4 mm/s to 1.0 mm/s. The axis passing frequency (APF) at the measuring points increases significantly and there appears new characteristic frequency of 3APF and 4APF. The numerical simulation results show that the front wear-ring abrasion affects the flow at the inlet of the front chamber of the pump and impeller passage. And the back wear-ring abrasion has obvious effect on the flow in the back chamber of the pump and impeller passage, while the multi-malfunction of the front wear-ring abrasion and back wear-ring abrasion has the most obvious effect on the flow velocity and flow stability inside pump. The pressure pulsation at Blade Passing Frequency (BPF) of the three schemes all decrease with the increase of the clearance.

scholarly journals Optimal Design of Slit Impeller for Low Specific Speed Centrifugal Pump Based on Orthogonal Test

2021 ◽  
Vol 9 (2) ◽  
pp. 121
Author(s):  
Yang Yang ◽  
Ling Zhou ◽  
Hongtao Zhou ◽  
Wanning Lv ◽  
Jian Wang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Pump ◽  
Large Scale ◽  
Internal Flow ◽  
Orthogonal Test ◽  
Centrifugal Pumps ◽  
Initial Model ◽  
Low Specific Speed ◽  
Specific Speed ◽  
Four Levels

Marine centrifugal pumps are mostly used on board ship, for transferring liquid from one point to another. Based on the combination of orthogonal testing and numerical simulation, this paper optimizes the structure of a drainage trough for a typical low-specific speed centrifugal pump, determines the priority of the various geometric factors of the drainage trough on the pump performance, and obtains the optimal impeller drainage trough scheme. The influence of drainage tank structure on the internal flow of a low-specific speed centrifugal pump is also analyzed. First, based on the experimental validation of the initial model, it is determined that the numerical simulation method used in this paper is highly accurate in predicting the performance of low-specific speed centrifugal pumps. Secondly, based on the three factors and four levels of the impeller drainage trough in the orthogonal test, the orthogonal test plan is determined and the orthogonal test results are analyzed. This work found that slit diameter and slit width have a large impact on the performance of low-specific speed centrifugal pumps, while long and short vane lap lengths have less impact. Finally, we compared the internal flow distribution between the initial model and the optimized model, and found that the slit structure could effectively reduce the pressure difference between the suction side and the pressure side of the blade. By weakening the large-scale vortex in the flow path and reducing the hydraulic losses, the drainage trough impellers obtained based on orthogonal tests can significantly improve the hydraulic efficiency of low-specific speed centrifugal pumps.

Numerical Modeling of Multi-Frequency Complex Dielectric Permittivity Dispersion of Sedimentary Rocks

Geophysics ◽  
2021 ◽  
pp. 1-69
Author(s):  
Artur Posenato Garcia ◽  
Zoya Heidari
Keyword(s):  
Numerical Simulation ◽  
Dielectric Permittivity ◽  
Numerical Simulations ◽  
Dielectric Response ◽  
Water Saturation ◽  
Pore Scale ◽  
Simulation Results ◽  
Wet Rocks ◽  
Permittivity Measurements ◽  
The Impact

The dielectric response of rocks results from electric double layer (EDL), Maxwell-Wagner (MW), and dipolar polarizations. The EDL polarization is a function of solid-fluid interfaces, pore water, and pore geometry. MW and dipolar polarizations are functions of charge accumulation at the interface between materials with contrasting impedances and the volumetric concentration of its constituents, respectively. However, conventional interpretation of dielectric measurements only accounts for volumetric concentrations of rock components and their permittivities, not interfacial properties such as wettability. Numerical simulations of dielectric response of rocks provides an ideal framework to quantify the impact of wettability and water saturation ( Sw) on electric polarization mechanisms. Therefore, in this paper we introduce a numerical simulation method to compute pore-scale dielectric dispersion effects in the interval from 100 Hz to 1 GHz including impacts of pore structure, Sw, and wettability on permittivity measurements. We solve the quasi-electrostatic Maxwell's equations in three-dimensional (3D) pore-scale rock images in the frequency domain using the finite volume method. Then, we verify simulation results for a spherical material by comparing with the corresponding analytical solution. Additionally, we introduce a technique to incorporate α-polarization to the simulation and we verify it by comparing pore-scale simulation results to experimental measurements on a Berea sandstone sample. Finally, we quantify the impact of Sw and wettability on broadband dielectric permittivity measurements through pore-scale numerical simulations. The numerical simulation results show that mixed-wet rocks are more sensitive than water-wet rocks to changes in Sw at sub-MHz frequencies. Furthermore, permittivity and conductivity of mixed-wet rocks have weaker and stronger dispersive behaviors, respectively, when compared to water-wet rocks. Finally, numerical simulations indicate that conductivity of mixed-wet rocks can vary by three orders of magnitude from 100 Hz to 1 GHz. Therefore, Archie’s equation calibrated at the wrong frequency could lead to water saturation errors of 73%.

scholarly journals Numerical Simulations of V-Shaped Plates Subjected to Blast Loadings: A Validation Study

2016 ◽  
Vol 10 (11) ◽  
pp. 203
Author(s):  
Mohd Zaid Othman ◽  
Qasim H. Shah ◽  
Muhammad Akram Muhammad Khan ◽  
Tan Kean Sheng ◽  
M. A. Yahaya ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Variable Mass ◽  
Blast Loading ◽  
Experimental Results ◽  
Average Difference ◽  
Simulation Results ◽  
Blast Loadings ◽  
Carrier Vehicle ◽  
Good Agreement

A series of numerical simulations utilizing LS-DYNA was performed to determine the mid-point deformations of V-shaped plates due to blast loading. The numerical simulation results were then compared with experimental results from published literature. The V-shaped plate is made of DOMEX 700 and is used underneath an armour personal carrier vehicle as an anti-tank mine to mitigate the effects of explosion from landmines in a battlefield. The performed numerical simulations of blast loading of V-shaped plates consisted of various angles i.e. 60°, 90°, 120°, 150° and 180°; variable mass of explosives located at the central mid-point of the V-shaped vertex with various stand-off distances. It could be seen that the numerical simulations produced good agreement with the experimental results where the average difference was about 26.6%.

scholarly journals Discussion on the Theoretical Basis for Cross-Over Method Applied to Downhole Wave Velocity Test

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Qing Dong ◽  
Zheng-hua Zhou ◽  
Su Jie ◽  
Bing Hao ◽  
Yuan-dong Li
Keyword(s):  
Numerical Simulation ◽  
Numerical Simulations ◽  
Wave Velocity ◽  
Theoretical Basis ◽  
Influence Factors ◽  
P Wave ◽  
Engineering Practice ◽  
S Wave ◽  
Simulation Results ◽  
The Cross

At engineering practice, the theoretical basis for the cross-over method, used to obtain shear wave arrival time in the downhole method of the wave velocity test by surface forward and backward strike, is that the polarity of P-wave keeps the same, while the polarity of S-wave transforms when the direction of strike inverted. However, the characteristics of signals recorded in tests are often found to conflict with this theoretical basis for the cross-over method, namely, the polarity of the P-wave also transforms under the action of surface forward and backward strike. Therefore, 3D finite element numerical simulations were conducted to study the validity of the theoretical basis for the cross-over method. The results show that both shear and compression waves are observed to be in 180° phase difference between horizontal signal traces, consistent with the direction of excitation generated by reversed impulse. Furthermore, numerical simulation results prove to be reliable by the analytic solution; it shows that the theoretical basis for the cross-over method applied to the downhole wave velocity test is improper. In meanwhile, numerical simulations reveal the factors (inclining excitation, geophone deflection, inclination, and background noise) that may cause the polarity of the P-wave not to reverse under surface forward and backward strike. Then, as to reduce the influence factors, we propose a method for the downhole wave velocity test under surface strike, the time difference of arrival is based between source peak and response peak, and numerical simulation results show that the S-wave velocity by this method is close to the theoretical S-wave velocity of soil.

Clocking effect in a centrifugal pump with a vaned diffuser

2020 ◽  
Vol 34 (26) ◽  
pp. 2050286
Author(s):  
Fen Lai ◽  
Xiangyuan Zhu ◽  
Yongqiang Duan ◽  
Guojun Li
Keyword(s):  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Loss ◽  
Total Pressure ◽  
Radial Force ◽  
Design Flow ◽  
Total Pressure Loss ◽  
Inlet Section ◽  
Centrifugal Pumps ◽  
Installation Angle

The performance and service life of centrifugal pumps can be influenced by the clocking effect. In this study, 3D numerical calculations based on the k-omega shear stress transport model are conducted to investigate the clocking effect in a centrifugal pump. Time-averaged behavior and transient behavior are analyzed. Results show that the optimum diffuser installation angle in the centrifugal pump is [Formula: see text] due to the minimum total pressure loss and radial force acting on the impeller. Total pressure loss, particularly in the volute, is considerably influenced by the clocking effect. The difference in total pressure loss in the volute at different clocking positions is 2.75 m under the design flow rate. The large total pressure loss in the volute is primarily caused by the large total pressure gradient within the vicinity of the volute tongue. The radial force acting on the impeller is also considerably affected by the clocking effect. When the diffuser installation angle is [Formula: see text], flow rate fluctuations in the volute and impeller passage are minimal, and flow rate distribution in the diffuser passage is more uniform than those in other diffuser installation angles. Moreover, static pressure fluctuations in the impeller midsection and the diffuser inlet section are at the minimum value. These phenomena explain the minimum radial force acting on the impeller. The findings of this study can provide a useful reference for the design of centrifugal pumps.

Vibrations of a Double Beam Structure Carrying a High-Pressure Driven Projectile

2019 ◽  
Author(s):  
Alexander Khair ◽  
Bingen Yang
Keyword(s):  
Numerical Simulation ◽  
Mathematical Model ◽  
High Pressure ◽  
Dynamic Stress ◽  
Beam Theory ◽  
Weapon System ◽  
Beam Structure ◽  
Double Beam ◽  
Simulation Results ◽  
Pressure Driven

Abstract In this paper, a mathematical model of a double beam structure carrying a high-pressure driven projectile is developed for investigation of the physical behaviors of gun barrels during firing. The dynamic response of such a weapon system is particularly interesting when reduction of muzzle vibrations and relevant dynamic stress in the structure is needed to improve the life cycle of the gun. In the model presented, the Timoshenko beam theory is implemented, and realistic characteristics of the physical system are considered. Numerical simulation results are presented for the displacement and rotation of the two beams, and the rigid-body projectile mass.

Numerical Simulation of High-Temperature Air Direct-Ignition of Pulverized Coal

2005 ◽  
Author(s):  
Z. Z. Kang ◽  
B. M. Sun ◽  
Y. H. Guo ◽  
W. Zhang ◽  
H. Q. Wei
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
High Temperature ◽  
Simulation Method ◽  
Pulverized Coal ◽  
Inlet Velocity ◽  
Operation Optimization ◽  
Structure Improvement ◽  
Simulation Results ◽  
Direct Ignition

Numerical simulation method is employed in this article to investigate various high-temperature air direct-ignition processes of pulverized coal (PC). Several important factors are analyzed, which are the inlet velocity of primary air flow, PC concentration and the velocity and temperature of high temperature air. The flow, combustion and heat transfer in high temperature air oil-free ignition burner can also be obtained from the simulation results, which are in accordance with the experimental data. The research provides guidance for structure improvement and operation optimization of burner.

Numerical study on instantaneous radial force of a centrifugal pump for different working conditions

2019 ◽  
Vol 37 (2) ◽  
pp. 458-480
Author(s):  
Xiaoqi Jia ◽  
Sheng Yuan ◽  
Zuchao Zhu ◽  
Baoling Cui
Keyword(s):  
Numerical Simulation ◽  
Unsteady Flow ◽  
Centrifugal Pump ◽  
Working Conditions ◽  
Flow Rate ◽  
Pressure Pulsation ◽  
Radial Force ◽  
Leakage Rate ◽  
Content Type ◽  
Three Components

Purpose Instantaneous radial force induced from unsteady flow will intensify vibration noise of the centrifugal pump, especially under off-design working conditions, which will affect safety reliability of pump operation in severe cases. This paper aims to conduct unsteady numerical computation on one centrifugal pump; thus, unsteady fluid radial force upon the impeller and volute is obtained, so as to study the evolution law of instantaneous radial force, the internal relationship between radial force and pressure pulsation, the relationship among each composition of radial force that the impeller received and the influence of leakage rate of front and back chamber on radial force. Design/methodology/approach The unsteady numerical simulation with SST k-ω turbulence model was carried out for a low specific-speed centrifugal pump using computational fluid dynamics codes FLUENT. The performance tests and pressure tests were conducted by a closed loop system. The performance curves and the pressure distribution from numerical simulation agree with that of the experiment conducted. The unsteady pressure distributions and the instantaneous radial forces induced from unsteady flow were analyzed under different flow rates. Contribution degrees of three components of the radial force on the impeller and the relation between the radial force and leakage rate were analyzed. Findings Radial force on the volute and pressure pulsation on the volute wall have the same distribution tendency, but in contrast to the distribution trend of the radial force on the impeller. In the component of radial force that the impeller received, radial force on the blade accounts for the main position. With the decrease of flow rate, ratio of the radial force on front and back casings will be increased; under large flow rate, vortex and flow blockage at volute section will enhance the pressure and radial force fluctuation greatly, and the pulsation degree may be much more intense than that of a smaller flow rate. Originality/value This paper revealed the relation of the radial force and the pressure pulsation. Meanwhile, contribution degrees of three components of the radial force on the impeller under different working conditions as well as the relation between the radial force and leakage rate of front and rear chambers were analyzed.

Sign in / Sign up

Export Citation Format

Share Document