Influence of Heat Treatment on Lithium Orthosilicate Pebbles

2012 ◽  
Vol 624 ◽  
pp. 208-211
Author(s):  
Hua Tang ◽  
Yu Tian Wang ◽  
Wei Jun Zhang ◽  
Li Shen ◽  
Yun Biao Duan ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Testing Machine ◽  
Lithium Carbonate ◽  
Treatment Temperature ◽  
Particle Sizes ◽  
Vacuum Tube ◽  
Heat Treated ◽  
Tube Type ◽  
Lithium Orthosilicate ◽  
Spraying Method

Abstract: The lithium orthosilicate pebbles was fabricated by melt spraying method with lithium carbonate (Li2CO3) and silicon dioxide (SiO2). By alter heat treatment temperature to study different particle sizes of lithium orthosilicate pebbles of strength and phase. Lithium orthosilicate pebbles which were heat treated by vacuum tube type furnace study change of phase ,by XRD to study the change of phase after the heat treatment and tested strength by universal testing machine. Heat treatment would alter strength and phase by vacuum tube type furnace.

Assessment of Mechanical Properties and Transformation Behavior of Locally-Made Ni-Ti Alloys Used in Orthodontics

2008 ◽  
Vol 55-57 ◽  
pp. 245-248 ◽  
Author(s):  
Nattiree Chiranavanit ◽  
Anak Khantachawana ◽  
N. Anuwongnukroh ◽  
Surachai Dechkunakorn
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Testing Machine ◽  
Optical Microscope ◽  
Treatment Temperature ◽  
Bending Test ◽  
Hardness Tester ◽  
Ti Alloys ◽  
Heat Treated ◽  
Average Grain Size

Ni-Ti alloy wires have been widely used in clinical orthodontics because of their properties of superelasticity (SE) and shape memory effect (SME). The purpose of this study was to assess the mechanical properties and phase transformation of 50.7Ni-49.3 Ti (at%) alloy (NT) and 45.2Ni-49.8Ti-5.0Cu (at%) alloy (NTC), cold-rolled with various percent reductions. To investigate SE and SME, heat-treatment was performed at 400°C and 600°C for 1 h. The specimens were examined using an Energy-Dispersive X-ray Spectroscope (EDS), Differential Scanning Calorimeter (DSC), Universal Testing Machine (Instron), Vickers Hardness Tester and Optical Microscope (OM). On the three-point bending test, the superelastic load-deflection curve was seen in NTC heat-treated at 400°C. Furthermore, NT heat-treated at 400°C with 30% reduction produced a partial superelastic curve. For SME, no conditions revealed superelasticity at the oral temperature. Micro-hardness value increased with greater percentage reduction. The average grain size for all specimens was typically 55-80 µm. The results showed that locally-made Ni-Ti alloys have various transformation behaviors and mechanical properties depending on three principal factors: chemical composition, work-hardening (the percent reduction) and heat-treatment temperature.

scholarly journals Enhancing Graphene Retention and Electrical Conductivity of Plasma-Sprayed Alumina/Graphene Nanoplatelets Coating by Powder Heat Treatment

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 643
Author(s):  
Xiaoyu Wu ◽  
Shufeng Xie ◽  
Kangwei Xu ◽  
Lei Huang ◽  
Daling Wei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Structural Integrity ◽  
Ceramic Coatings ◽  
Treatment Temperature ◽  
Graphene Nanoplatelets ◽  
Structural Defects ◽  
Temperature Plasma ◽  
Heat Treated ◽  
Plasma Sprayed

Burning loss of graphene in the high-temperature plasma-spraying process is a critical issue, significantly limiting the remarkable performance improvement in graphene reinforced ceramic coatings. Here, we reported an effective approach to enhance the graphene retention, and thus improve the performance of plasma-sprayed alumina/graphene nanoplatelets (Al2O3/GNPs) coatings by heat treatment of agglomerated Al2O3/GNPs powders. The effect of powder heat treatment on the microstructure, GNPs retention, and electrical conductivity of Al2O3/GNPs coatings were systematically investigated. The results indicated that, with the increase in the powder heat treatment temperature, the plasma-sprayed Al2O3/GNPs coatings exhibited decreased porosity and improved adhesive strength. Thermogravimetric analysis and Raman spectra results indicated that increased GNPs retention from 12.9% to 28.4%, and further to 37.4%, as well as decreased structural defects, were obtained for the AG, AG850, and AG1280 coatings, respectively, which were fabricated by using AG powders without heat treatment, powders heat-treated at 850 °C, and powders heat-treated at 1280 °C. Moreover, the electrical conductivities of AG, AG850, and AG1280 coatings exhibited 3 orders, 4 orders, and 7 orders of magnitude higher than that of Al2O3 coating, respectively. Powder heat treatment is considered to increase the melting degree of agglomerated alumina particles, eventually leaving less thermal energy for GNPs to burn; thus, a high retention amount and structural integrity of GNPs and significantly enhanced electrical conductivity were achieved for the plasma-sprayed Al2O3/GNPs coatings.

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Mechanical and Superelastic Properties of Au-51Ti-18Co Biomedical Shape Memory Alloy Heat-Treated at 1173 K to 1373 K

2016 ◽  
Vol 97 ◽  
pp. 141-146 ◽  
Author(s):  
Taywin Buasri ◽  
Hyunbo Shim ◽  
Masaki Tahara ◽  
Tomonari Inamura ◽  
Kenji Goto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Critical Stress ◽  
Biomedical Applications ◽  
Shape Recovery ◽  
Treatment Temperature ◽  
Recovery Ratio ◽  
Recovery Strain ◽  
Heat Treated ◽  
Alloy Heat

The effect of heat treatment temperature from 1173 K to 1373 K for 3.6 ks on mechanical and superelastic properties of an Ni-free Au-51Ti-18Co alloy (mol%) was investigated. The stress for inducing martensitic transformation (SIMT) and the critical stress for slip deformation (CSS) slightly decrease with increasing the heat–treatment temperature. Regardless of heat–treatment temperature, good superelasticity was definitely recognized with the maximum shape recovery ratio up to 95 % and 4 % superelastic shape recovery strain. As the mentioned reasons, the Au-51Ti-18Co alloy is promising for practical biomedical applications.

Investigation of Heat Treated Electrodeposited CoNiFe on Microstructure and Hardness

2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Heat Treated ◽  
Hardness Property ◽  
Finishing Process ◽  
The Face ◽  
Face Centered

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.

Effects of Heat-Treatment Temperature on the Properties of Negative CTE Eucryptite Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 123-125 ◽  
Author(s):  
Yong Li ◽  
Qi Hong Wei ◽  
Ling Li ◽  
Chong Hai Wang ◽  
Xiao Li Zhang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Thermal Expansion ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Heat Treatment Temperature ◽  
Bending Strength ◽  
Sol Gel ◽  
Negative Thermal Expansion ◽  
Treatment Temperature ◽  
Heat Treated

In this paper, negative thermal expansion coefficient eucryptite powders were prepared by sol-gel method using silica-sol as starting material. The raw blocks were obtained by dry pressing process after the powder was synthesized, and then the raw blocks were heat-treated at 600º, 1150º, 1280º, 1380º, 1420º and 1450°C, respectively. Variations of density, porosity and thermal expansion coefficient at different heat treatment temperatures were investigated. Phase transformation and fracture surface morphology of eucryptite heat-treated at different temperatures, respectively, were observed by XRD and SEM. The results indicate that, with the increasing heat- treatment temperature, the grain size and the bending strength increased, porosity decreased, thermal expansion coefficient decreased continuously. Negative thermal expansion coefficient of -5.3162×10-6~-7.4413×10-6 (0~800°C) was obtained. But when the heat-treatment temperature was more than 1420°C, porosity began to increase, bending strength began to decrease, which were the symbols of over-burning, while the main crystal phase didn’t change.

scholarly journals Effect of Heat Treatment Temperature on Martensitic Transformation and Superelasticity of the Ti49Ni51 Shape Memory Alloy

Materials ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 2539 ◽  
Author(s):  
Peiyou Li ◽  
Yongshan Wang ◽  
Fanying Meng ◽  
Le Cao ◽  
Zhirong He
Keyword(s):  
Heat Treatment ◽  
Martensitic Transformation ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Thermal Hysteresis ◽  
Treatment Temperature ◽  
Heat Treated ◽  
Different Temperatures ◽  
Tini Phase ◽  
Rapidly Solidified

The martensitic transformation and superelasticity of Ti49Ni51 shape memory alloy heat-treatment at different temperatures were investigated. The experimental results show that the microstructures of as-cast and heat-treated (723 K) Ni-rich Ti49Ni51 samples prepared by rapidly-solidified technology are composed of B2 TiNi phase, and Ti3Ni4 and Ti2Ni phases; the microstructures of heat-treated Ti49Ni51 samples at 773 and 823 K are composed of B2 TiNi phase, and of B2 TiNi and Ti2Ni phases, respectively. The martensitic transformation of as-cast Ti49Ni51 alloy is three-stage, A→R→M1 and R→M2 transformation during cooling, and two-stage, M→R→A transformation during heating. The transformations of the heat-treated Ti49Ni51 samples at 723 and 823 K are the A↔R↔M/A↔M transformation during cooling/heating, respectively. For the heat-treated alloy at 773 K, the transformations are the A→R/M→R→A during cooling/heating, respectively. For the heat-treated alloy at 773 K, only a small thermal hysteresis is suitable for sensor devices. The stable σmax values of 723 and 773 K heat-treated samples with a large Wd value exhibit high safety in application. The 773 and 823 K heat-treated samples have large stable strain–energy densities, and are a good superelastic alloy. The experimental data obtained provide a valuable reference for the industrial application of rapidly-solidified casting and heat-treated Ti49Ni51 alloy.

Effect of Heat Treatment on the Combustion Characteristics of a Lignite

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Zhezi Zhang ◽  
Mingming Zhu ◽  
Jianbo Li ◽  
Kai Zhang ◽  
Guoqing Shen ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Ignition Delay ◽  
Delay Time ◽  
Heat Treatment Temperature ◽  
Ignition Delay Time ◽  
Treatment Temperature ◽  
Ftir Analysis ◽  
Single Particles ◽  
Heat Treated ◽  
Ignition And Combustion

In this study, the ignition and combustion behavior of raw and heat-treated single particles of lignite were experimentally investigated, with a focus on the effect of heat treatment temperatures. The lignite particles were heat treated to various final temperatures (473, 623 and 773 K) in nitrogen and characterized using proximate, ultimate, and Fourier transform infrared spectroscopy (FTIR) analysis. A single lignite particle of 2 or 3 mm in diameter was suspended on a silicon carbide fiber and burned in air in a horizontal tube furnace operating at 1123 K. The ignition and combustion process of the particle was record using a color CCD camera at 25 fps. The ignition mechanism, ignition delay time, volatile flame duration, and burnout time of the single particles were examined by processing the recorded images. The proximate and ultimate analysis results indicated that the volatile matter and oxygen contents decreased, while the carbon content increased with increasing temperature of heat treatment. This trend was consistent with observations in the FTIR analysis, in which the intensity of oxygen-containing functional groups decreased with increasing the heat treatment temperature. The ignition of raw and heat treated lignite particles followed a joint hetero-homogeneous mechanism under all conditions studied. The ignition delay time, volatile flame extinction time, and the total combustion time decreased with increasing heat treatment temperature up to 623 K. A further increase in the heat treatment temperature to 773 K resulted in prolonged key ignition and combustion characteristic times.

Effect of Heat Treatment on the Reactivity and Crystallinity of Coal-Char

2005 ◽  
Author(s):  
Shouyu Zhang ◽  
Junfu Lu ◽  
Jianmin Zhang ◽  
Qing Liu ◽  
Guangxi Yue
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Time ◽  
Treatment Temperature ◽  
Coal Char ◽  
Heat Treatment Time ◽  
Heat Treat ◽  
Heat Treated ◽  
Layer Stacking ◽  
Crystalline Growth

The effect of heat treatment on the reactivity and crystallinity of char prepared from the vitrinite of two coals (YX, JJ) was investigated by using XRD and TGA in this paper. The results from TGA show that the reactivity of the chars from YXV and JJV decreases with the increase of heat treatment temperature. The reactivity of YXV char decreases quickly and significantly as heat treatment time increases. However, after heat treatment time of 60 min, it decreases slowly. The effect of heat treatment time on the reactivity of JJV char is small. The results from XRD show that the crystallinity of coal-char is determined by the intensity of heat treatment. When heat treatment time is more than 60 minutes, the turbostratic crystallite of YXV char prepared under 900°C changes remarkably and becomes more orderly. The aromatic layer stacking heights (Lc) of YXV Char when heat treated above 900°C increased with the increase of heat treatment time. The effect of heat treat time on Lc of JJV char is small, but under heat treatment temperature of 1200°C, the crystalline of JJV char grows distinctly. There is a good parallel relationship between the crystalline growth and deactivation of the chars. It can be concluded that the growth of the crystalline is the main reason for the deactivation of coal-char.

Sign in / Sign up

Export Citation Format

Share Document