Thermal Properties of the Polyolefin Based Elastic Filament DOW XLATM

2012 ◽  
Vol 627 ◽  
pp. 143-146
Author(s):  
Ni Wang ◽  
Zhao Lin Liu ◽  
Xi Ting Chen
Keyword(s):  
Heat Treatment ◽  
Thermal Properties ◽  
Loss Rate ◽  
Elastic Recovery ◽  
Treatment Temperature ◽  
Scanning Calorimetry ◽  
Weight Loss Rate ◽  
Highest Weight ◽  
Heat Treated ◽  
Elastic Filament

Thermal properties of the elastic filament DOW XLATMwere analyzed by differential scanning calorimetry (DSC) and thermogravimetry analysis (TG). Besides, the elastic recovery characteristics after heat treatment were also discussed. The DSC scan shows typical endotherms and its melting temperature (Tm) ranges from 28 °C- 65 °C. TG analysis indicates that the thermal degradation begins at 285 °C and the highest weight loss rate occurs at 461.9 oC. When the filaments are heat treated under relaxation or at constant elongatiSuperscript texton, their elastic recovery ratios all decrease with the increase of the heat treatment temperature except for 50 °C.

Effects of Calcium Carbonate on the Thermal Properties of Acrylonitrile-Butadiene-Styrene/Calcium Carbonate Composites

2013 ◽  
Vol 834-836 ◽  
pp. 276-280
Author(s):  
Xiao Juan Bai ◽  
Ling Wang
Keyword(s):  
Thermal Properties ◽  
Calcium Carbonate ◽  
Loss Rate ◽  
Acrylonitrile Butadiene Styrene ◽  
Mixed Gas ◽  
Scanning Calorimetry ◽  
Weight Loss Rate ◽  
Thermal Stability Of ◽  
Butadiene Styrene ◽  
Maximum Weight Loss

Calcium carbonate (CaCO3) is a filler widely used in plastics. In this study, the effects of CaCO3content and size on the thermal properties of acrylonitrile-butadiene-styrene (ABS)/CaCO3composites were determined by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA results in nitrogen showed that the maximum weight loss rate of the composites gradually decreased with increasing CaCO3content. TGA results in a mixed gas containing oxygen showed that CaCO3addition facilitated the degradation of ABS, and ABS degradation was completed at relatively low temperatures. The effect of nano-CaCO3on the thermal stability of the composites was similar to that of microsized CaCO3.

Electrophoretic Deposition and Heat Treatment of Steel-Supported PVDF-Graphite Composite Film

2015 ◽  
Vol 761 ◽  
pp. 412-416 ◽  
Author(s):  
Kok Tee Lau ◽  
Mohd Hafrez Razi Ab Razak ◽  
Swee Leong Kok ◽  
Muhammad Zaimi ◽  
Mohd Warikh Abd Rashid ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Composite Film ◽  
Electrophoretic Deposition ◽  
Composite Films ◽  
Treatment Temperature ◽  
Final Heat Treatment ◽  
Scanning Calorimetry ◽  
Graphite Composite ◽  
Final Heat ◽  
Heat Treated

Polymeric poly (vinyliden fluoride) (PVDF) is nontoxic. It possesses a better mechanical flexibility and requires a lower synthesis temperature, as compared to the piezoceramic counterparts. In order to achieve a competitive advantage against the current piezoelectric sensor, graphite could replace a more expensive silver-palladium as the electrodes for the piezoelectric PVDF. This paper reports the preliminary results on the synthesis of steel-supported graphite-PVDF/PVDF/graphite-PVDF composite films using the two-step process, consisted of the electrophoretic deposition (EPD) and heat treatment. The composite films were characterized by means of the optical microscopy, scanning electron microscopy, X-ray diffraction and differential scanning calorimetry. The heat treated graphite-PVDF electrode deposited by EPD provides adequate mechanical strength for the subsequent depositions of pure PVDF layer and the second layer of graphite-PVDF composite electrode. However, the final heat treatment stage did not eliminate the fine and large cracks of the composite film, which might be attributed to high residue stresses and weak bonding between graphite and PVDF particles in the post-heat treated composite films. Nevertheless, the increase in final heat treatment temperature of the composite film at Stage 3 improved the graphite and PVDF grain alignment, as well as its crystallinity.

Preparation and Characterization of Superionic Conductive Li2O-Al2O3-La2O3-TiO2-P2O5 Glass-Ceramics

2012 ◽  
Vol 509 ◽  
pp. 314-320 ◽  
Author(s):  
Hong Ping Chen ◽  
Hai Zheng Tao ◽  
Qi De Wu ◽  
Xiu Jian Zhao
Keyword(s):  
Heat Treatment ◽  
Glass Ceramic ◽  
Glass Ceramics ◽  
Lithium Ion ◽  
Treatment Temperature ◽  
Total Conductivity ◽  
Scanning Calorimetry ◽  
Structural Morphology ◽  
Heat Treated ◽  
Different Temperatures

Li2O-Al2O3(La2O3)-TiO2-P2O5 glass-ceramics were fabricated through heat-treatment of the original glass. The differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and electrochemical workstation were employed to study the structural, morphology and electrical properties of the samples heat-treated at different temperatures. The results showed that: the glass-ceramics consist of the dominating LiTi2(PO4)3 phases, trifle AlPO4, TiO2 and unknown phases. With the heat-treatment temperature increasing from 700 °C to 1100 °C, the structure of glass-ceramic become denser and grain grew, lithium ion conductivity increased quickly and subsequent cut down gradually. While the specimen was obtained by crystallization at 900 °C for 12 h, the total conductivity of glass-ceramic material come up to the maximum (5.85 ×10-4 S•cm-1) at 25 °C. This inorganic solid electrolyte has a potential application in lithium batteries or other devices.

Synthesis and properties of a benzoxazine monomer containing maleimide and biphenyl groups

2021 ◽  
pp. 095400832199674
Author(s):  
Tao Guo ◽  
Yang Fan ◽  
Chang Bo ◽  
Zhang Qi ◽  
Han Tao ◽  
...  
Keyword(s):  
Weight Loss ◽  
Loss Rate ◽  
Proton Nuclear Magnetic Resonance ◽  
Significant Weight Loss ◽  
Scanning Calorimetry ◽  
Weight Loss Rate ◽  
Reaction Heat ◽  
H Nmr ◽  
Curing Reaction ◽  
Dsc Curves

Benzoxazine resin exhibits excellent properties and is widely used in many fields. Herein, the synthesis of a novel compound, the bis(2,4-dihydro-2 H-3-(4- N-maleimido)phenyl-1,3-benzoxazinyl)biphenyl (BMIPBB), has been reported, which was synthesized by reacting N-(4-aminophenyl)maleimide (APMI), formaldehyde, and 4,4’-dihydroxybiphenyl. 1,3,5-three(4-(maleimido)phenyl)-1,3,5-triazine (TMIPT) was formed as an intermediate during the reaction. The proton nuclear magnetic resonance (1H-NMR) and Fourier transform-infrared (FTIR) spectroscopy experiments were conducted to determine the structure of BMIPBB. BMIPBB was obtained as a reddish-brown solid in 40.1% yield. The thermal properties of BMIPBB were investigated using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. Analysis of the DSC curves revealed that the broad peak representing the release of curing reaction heat appeared in the temperature range of 140–330°C. The peak temperature was 242.59°C and the heat of the reaction was 393.82 J/g, indicating that the rate of the curing reaction was low and the heat of the reaction was high. Analysis of the TGA results revealed that the weight loss rate was 5% at 110°C. The monomer exhibited a significant weight loss in the range of 320–500°C. The compound lost 50% of its weight at a temperature of 427°C.

scholarly journals Enhancing Graphene Retention and Electrical Conductivity of Plasma-Sprayed Alumina/Graphene Nanoplatelets Coating by Powder Heat Treatment

Coatings ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 643
Author(s):  
Xiaoyu Wu ◽  
Shufeng Xie ◽  
Kangwei Xu ◽  
Lei Huang ◽  
Daling Wei ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Electrical Conductivity ◽  
Structural Integrity ◽  
Ceramic Coatings ◽  
Treatment Temperature ◽  
Graphene Nanoplatelets ◽  
Structural Defects ◽  
Temperature Plasma ◽  
Heat Treated ◽  
Plasma Sprayed

Burning loss of graphene in the high-temperature plasma-spraying process is a critical issue, significantly limiting the remarkable performance improvement in graphene reinforced ceramic coatings. Here, we reported an effective approach to enhance the graphene retention, and thus improve the performance of plasma-sprayed alumina/graphene nanoplatelets (Al2O3/GNPs) coatings by heat treatment of agglomerated Al2O3/GNPs powders. The effect of powder heat treatment on the microstructure, GNPs retention, and electrical conductivity of Al2O3/GNPs coatings were systematically investigated. The results indicated that, with the increase in the powder heat treatment temperature, the plasma-sprayed Al2O3/GNPs coatings exhibited decreased porosity and improved adhesive strength. Thermogravimetric analysis and Raman spectra results indicated that increased GNPs retention from 12.9% to 28.4%, and further to 37.4%, as well as decreased structural defects, were obtained for the AG, AG850, and AG1280 coatings, respectively, which were fabricated by using AG powders without heat treatment, powders heat-treated at 850 °C, and powders heat-treated at 1280 °C. Moreover, the electrical conductivities of AG, AG850, and AG1280 coatings exhibited 3 orders, 4 orders, and 7 orders of magnitude higher than that of Al2O3 coating, respectively. Powder heat treatment is considered to increase the melting degree of agglomerated alumina particles, eventually leaving less thermal energy for GNPs to burn; thus, a high retention amount and structural integrity of GNPs and significantly enhanced electrical conductivity were achieved for the plasma-sprayed Al2O3/GNPs coatings.

scholarly journals Water Resistance and Creep Behavior of Heat-Treated Moso Bamboo Determined by the Stepped Isostress Method

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1264
Author(s):  
Teng-Chun Yang ◽  
Tung-Lin Wu ◽  
Chin-Hao Yeh
Keyword(s):  
Heat Treatment ◽  
Water Absorption ◽  
Creep Behavior ◽  
Heat Treatment Temperature ◽  
Water Resistance ◽  
Absorption Efficiency ◽  
Treatment Temperature ◽  
Moso Bamboo ◽  
Phyllostachys Pubescens ◽  
Heat Treated

The influence of heat treatment on the physico-mechanical properties, water resistance, and creep behavior of moso bamboo (Phyllostachys pubescens) was determined in this study. The results revealed that the density, moisture content, and flexural properties showed negative relationships with the heat treatment temperature, while an improvement in the dimensional stability (anti-swelling efficiency and anti-water absorption efficiency) of heat-treated samples was observed during water absorption tests. Additionally, the creep master curves of the untreated and heat-treated samples were successfully constructed using the stepped isostress method (SSM) at a series of elevated stresses. Furthermore, the SSM-predicted creep compliance curves fit well with the 90-day full-scale experimental data. When the heat treatment temperature increased to 180 °C, the degradation ratio of the creep resistance (rd) significantly increased over all periods. However, the rd of the tested bamboo decreased as the heat treatment temperature increased up to 220 °C.

Effect of Heat Treatment on the Microstructure and Property of TiAl Alloys Prepared by Gas Atomization Powders

2013 ◽  
Vol 747-748 ◽  
pp. 497-501
Author(s):  
Na Liu ◽  
Zhou Li ◽  
Guo Qing Zhang ◽  
Hua Yuan ◽  
Wen Yong Xu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Tial Alloy ◽  
Lamellar Microstructure ◽  
Treatment Temperature ◽  
Gas Atomization ◽  
Thermally Induced ◽  
Heat Treated ◽  
Fine Duplex ◽  
Step Heat Treatment

Powder metallurgical TiAl alloy was fabricated by gas atomization powders, and the effect of heat treatment temperature on the microstructure evolution and room tensile properties of PM TiAl alloy was investigated. The uniform fine duplex microstructure was formed in PM TiAl based alloy after being heat treated at 1250/2h followed by furnace cooling (FC)+ 900/6h (FC). When the first step heat treatment temperature was improved to 1360/1h, the near lamellar microstructure was achieved. The ductility of the alloy after heat treatment improved markedly to 1.2% and 0.6%, but the tensile strength decreased to 570MPa and 600MPa compared to 655MPa of as-HIP TiAl alloy. Post heat treatment at the higher temperature in the alpha plus gamma field would regenerate thermally induced porosity (TIP).

Mechanical and Superelastic Properties of Au-51Ti-18Co Biomedical Shape Memory Alloy Heat-Treated at 1173 K to 1373 K

2016 ◽  
Vol 97 ◽  
pp. 141-146 ◽  
Author(s):  
Taywin Buasri ◽  
Hyunbo Shim ◽  
Masaki Tahara ◽  
Tomonari Inamura ◽  
Kenji Goto ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Critical Stress ◽  
Biomedical Applications ◽  
Shape Recovery ◽  
Treatment Temperature ◽  
Recovery Ratio ◽  
Recovery Strain ◽  
Heat Treated ◽  
Alloy Heat

The effect of heat treatment temperature from 1173 K to 1373 K for 3.6 ks on mechanical and superelastic properties of an Ni-free Au-51Ti-18Co alloy (mol%) was investigated. The stress for inducing martensitic transformation (SIMT) and the critical stress for slip deformation (CSS) slightly decrease with increasing the heat–treatment temperature. Regardless of heat–treatment temperature, good superelasticity was definitely recognized with the maximum shape recovery ratio up to 95 % and 4 % superelastic shape recovery strain. As the mentioned reasons, the Au-51Ti-18Co alloy is promising for practical biomedical applications.

Investigation of Heat Treated Electrodeposited CoNiFe on Microstructure and Hardness

2015 ◽  
Vol 1113 ◽  
pp. 56-61
Author(s):  
Nor Azrina Resali ◽  
Koay Mei Hyie ◽  
M.N. Berhan ◽  
C.M. Mardziah
Keyword(s):  
Heat Treatment ◽  
Heat Treatment Temperature ◽  
Treatment Temperature ◽  
Crystallographic Structure ◽  
Face Centered Cubic ◽  
Heat Treated ◽  
Hardness Property ◽  
Finishing Process ◽  
The Face ◽  
Face Centered

In this research, heat treatment is the final finishing process applied on nanocrystalline CoNiFe to improve microstructure for good hardness property. Nanocrystalline CoNiFe has been synthesized using the electrodeposition method. This study investigated the effect of heat treatment at 500°C, 600°C, 700°C and 800°C on electrodeposited nanocrystalline CoNiFe. The heat treatment process was performed in the tube furnace with flowing Argon gas. By changing the heat treatment temperature, physical properties such as phase and crystallographic structure, surface morphology, grain size and hardness of nanocrystalline CoNiFe was studied. The nanocrystalline CoNiFe phase revealed the Face Centered Cubic (FCC) and Body Centered Cubic (BCC) crystal structure. FESEM micrographs showed that the grain sizes of the coatings were in the range of 78.76 nm to 132 nm. Dendrite shape was found in the microstructure of nanocrystalline CoNiFe. The nanocrystalline CoNiFe prepared in heat treatment temperature of 700°C, achieved the highest hardness of 449 HVN. The surface roughness of nanocrystalline CoNiFe heated at 700°C was found to be smaller than other temperatures.

Effects of Heat-Treatment Temperature on the Properties of Negative CTE Eucryptite Ceramics

2010 ◽  
Vol 105-106 ◽  
pp. 123-125 ◽  
Author(s):  
Yong Li ◽  
Qi Hong Wei ◽  
Ling Li ◽  
Chong Hai Wang ◽  
Xiao Li Zhang ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Thermal Expansion ◽  
Thermal Expansion Coefficient ◽  
Expansion Coefficient ◽  
Heat Treatment Temperature ◽  
Bending Strength ◽  
Sol Gel ◽  
Negative Thermal Expansion ◽  
Treatment Temperature ◽  
Heat Treated

In this paper, negative thermal expansion coefficient eucryptite powders were prepared by sol-gel method using silica-sol as starting material. The raw blocks were obtained by dry pressing process after the powder was synthesized, and then the raw blocks were heat-treated at 600º, 1150º, 1280º, 1380º, 1420º and 1450°C, respectively. Variations of density, porosity and thermal expansion coefficient at different heat treatment temperatures were investigated. Phase transformation and fracture surface morphology of eucryptite heat-treated at different temperatures, respectively, were observed by XRD and SEM. The results indicate that, with the increasing heat- treatment temperature, the grain size and the bending strength increased, porosity decreased, thermal expansion coefficient decreased continuously. Negative thermal expansion coefficient of -5.3162×10-6~-7.4413×10-6 (0~800°C) was obtained. But when the heat-treatment temperature was more than 1420°C, porosity began to increase, bending strength began to decrease, which were the symbols of over-burning, while the main crystal phase didn’t change.

Sign in / Sign up

Export Citation Format

Share Document