Integrated Sensing, Monitoring and Healing of Composite Systems

2016 ◽  
Vol 101 ◽  
pp. 62-68
Author(s):  
Oluwafemi Sedoten Kuponu ◽  
Visakan Kadirkamanathan ◽  
Bishakh Bhattacharya ◽  
Simon Alexander Pope
Keyword(s):  
Composite Materials ◽  
Failure Rate ◽  
Feedback Loop ◽  
Healing Rate ◽  
Research Community ◽  
Self Healing ◽  
Thin Line ◽  
Composite Systems ◽  
Damage Rate ◽  
Healing System

The ability of a material to recover its nominal properties through self-healing is gaininginterest in the research community. However, current approaches remain predominantly passive incounteracting the effect of damage. As a result, healing only begins when the material has occurreddamage and typically there is a mismatch between the healing and damage rate. For applications suchas aircraft, where there is a thin line between functionality and non-functionality, these limitations maybe inherently restrictive. A self-healing system that combines a prognosis unit to predict and estimatethe failure rate and an active self-healing system that matches the healing rate to the estimated failurerate using a feedback loop, has the potential to overcome these limitations. In this paper we proposesuch a system and present results for its application to composite materials.

scholarly journals Zn-Co-CeO2 vs. Zn-Co Coatings: Effect of CeO2 Sol in the Enhancement of the Corrosion Performance of Electrodeposited Composite Coatings

Metals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 704
Author(s):  
Marija Riđošić ◽  
Nebojša D. Nikolić ◽  
Asier Salicio-Paz ◽  
Eva García-Lecina ◽  
Ljiljana S. Živković ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Healing Rate ◽  
Electrochemical Impedance ◽  
Composite Coatings ◽  
Self Healing ◽  
Kelvin Probe ◽  
Artificial Defect ◽  
Volta Potential ◽  
Superior Corrosion Resistance ◽  
The Stability

Electrodeposition and characterization of novel ceria-doped Zn-Co composite coatings was the main goal of this research. Electrodeposited composite coatings were compared to pure Zn-Co coatings obtained under the same conditions. The effect of two ceria sources, powder and home-made sol, on the morphology and corrosion resistance of the composite coatings was determined. During the electrodeposition process the plating solution was successfully agitated in an ultrasound bath. The source of the particles was found to influence the stability and dispersity of plating solutions. The application of ceria sol resulted in an increase of the ceria content in the resulting coating and favored the refinement from cauliflower-like morphology (Zn-Co) to uniform and compact coral-like structure (Zn-Co-CeO2 sol). The corrosion resistance of the composite coatings was enhanced compared to bare Zn-Co as evidenced by electrochemical impedance spectroscopy and scanning Kelvin probe results. Zn-Co doped with ceria particles originating from ceria sol exhibited superior corrosion resistance compared to Zn-Co-CeO2 (powder) coatings. The self-healing rate of artificial defect was calculated based on measured Volta potential difference for which Zn-Co-CeO2 (sol) coatings exhibited a self-healing rate of 73.28% in a chloride-rich environment.

scholarly journals The Effect of Superabsorbent Polymers on the Microstructure and Self-Healing Properties of Cementitious-Based Composite Materials

2021 ◽  
Vol 11 (2) ◽  
pp. 700
Author(s):  
Irene A. Kanellopoulou ◽  
Ioannis A. Kartsonakis ◽  
Costas A. Charitidis
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Hybrid Structure ◽  
The Self ◽  
Self Healing ◽  
Cementitious Composite ◽  
Superabsorbent Polymers ◽  
Porosity Reduction ◽  
Environment Control ◽  
The Impact

Cementitious structures have prevailed worldwide and are expected to exhibit further growth in the future. Nevertheless, cement cracking is an issue that needs to be addressed in order to enhance structure durability and sustainability especially when exposed to aggressive environments. The purpose of this work was to examine the impact of the Superabsorbent Polymers (SAPs) incorporation into cementitious composite materials (mortars) with respect to their structure (hybrid structure consisting of organic core—inorganic shell) and evaluate the microstructure and self-healing properties of the obtained mortars. The applied SAPs were tailored to maintain their functionality in the cementitious environment. Control and mortar/SAPs specimens with two different SAPs concentrations (1 and 2% bwoc) were molded and their mechanical properties were determined according to EN 196-1, while their microstructure and self-healing behavior were evaluated via microCT. Compressive strength, a key property for mortars, which often degrades with SAPs incorporation, in this work, practically remained intact for all specimens. This is coherent with the porosity reduction and the narrower range of pore size distribution for the mortar/SAPs specimens as determined via microCT. Moreover, the self-healing behavior of mortar-SAPs specimens was enhanced up to 60% compared to control specimens. Conclusively, the overall SAPs functionality in cementitious-based materials was optimized.

scholarly journals Influencing Factors on the Healing Performance of Microcapsule Self-Healing Concrete

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4139
Author(s):  
Yanju Wang ◽  
Zhiyang Lin ◽  
Can Tang ◽  
Wenfeng Hao
Keyword(s):  
Compressive Strength ◽  
Sodium Silicate ◽  
Recovery Rate ◽  
Sound Speed ◽  
Orthogonal Experimental Design ◽  
Self Healing ◽  
Damage Degree ◽  
Strength Recovery ◽  
Healing System ◽  
Recovery Performance

The amounts of the components in a microcapsule self-healing system significantly impact the basic performance and self-healing performance of concrete. In this paper, an orthogonal experimental design is used to investigate the healing performance of microcapsule self-healing concrete under different pre-damage loads. The strength recovery performance and sound speed recovery performance under extensive damage are analyzed. The optimum factor combination of the microcapsule self-healing concrete is obtained. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) are carried out on the concrete samples before and after healing to determine the healing mechanism. The results show that the healing effect of self-healing concrete decreases with an increase in the pre-damage load, and the sound speed recovery rate increases with an increase in the damage degree. The influence of the sodium silicate content on the compressive strength and compressive strength recovery rate of the self-healing concrete increases, followed by a decrease. The optimum combination of factors of the microcapsule self-healing system is 3% microcapsules, 30% sodium silicate, and 15% sodium fluosilicate. The results can be used for the design and preparation of self-healing concrete.

The Design of Composite Materials For Electro-Mechanical and Electro-Thermal Applications.

1983 ◽  
Vol 24 ◽  
Author(s):  
L. E. Cross
Keyword(s):  
Composite Materials ◽  
Figure Of Merit ◽  
Poisson Ratio ◽  
Dielectric Behavior ◽  
Thermal Mass ◽  
Secondary Effects ◽  
Pressure Sensing ◽  
Composite Systems ◽  
Reinforced Composite ◽  
Composite Microstructure

ABSTRACTIn composite materials for electro-mechanical applications, the importance of the mode in which the constituent phases are interconnected (connectivity) was stressed. For the tensor properties of mechanical, piezoelectric, and dielectric behavior, controlling the manner in which fields and fluxes thread through the composite can make orders of magnitude change in the coupled properties.Examples were drawn from piezoelectric ceramic:polymer composites for uniaxial and hydrostatic (hydrophone) pressure sensing where the 1:3 connected transversely reinforced composite can be shown to exhibit a figure of merit more than 103 that of the piezoceramic phase alone. In these systems, the importance of poisson ratio effects in the polymer phase were evident, and some new composite systems where the hydrostatic stiffness of the elastomer phases may be better exploited were considered.In electro-thermal applications such as in pyroelectric composites, the requirements of small-size and low-thermal mass put rigorous limits upon the scale of the composite microstructure. Techniques which achieve the appropriate scaling were described and preliminary data showed strong enhancement of the secondary effects in these composites were presented.

scholarly journals Self-Healing Materials for Electronics Applications

2022 ◽  
Vol 23 (2) ◽  
pp. 622
Author(s):  
Fouzia Mashkoor ◽  
Sun Jin Lee ◽  
Hoon Yi ◽  
Seung Man Noh ◽  
Changyoon Jeong
Keyword(s):  
Energy Storage ◽  
Composite Materials ◽  
Crack Formation ◽  
Review Article ◽  
Self Healing ◽  
Energy Storage Devices ◽  
Storage Devices ◽  
The Past ◽  
Repair Mechanisms ◽  
Energy Harvesting Devices

Self-healing materials have been attracting the attention of the scientists over the past few decades because of their effectiveness in detecting damage and their autonomic healing response. Self-healing materials are an evolving and intriguing field of study that could lead to a substantial increase in the lifespan of materials, improve the reliability of materials, increase product safety, and lower product replacement costs. Within the past few years, various autonomic and non-autonomic self-healing systems have been developed using various approaches for a variety of applications. The inclusion of appropriate functionalities into these materials by various chemistries has enhanced their repair mechanisms activated by crack formation. This review article summarizes various self-healing techniques that are currently being explored and the associated chemistries that are involved in the preparation of self-healing composite materials. This paper further surveys the electronic applications of self-healing materials in the fields of energy harvesting devices, energy storage devices, and sensors. We expect this article to provide the reader with a far deeper understanding of self-healing materials and their healing mechanisms in various electronics applications.

Investigating the Success of OSS Software Projects

2015 ◽  
pp. 92-102
Author(s):  
Amir Hossein Ghapanchi
Keyword(s):  
Open Source ◽  
Failure Rate ◽  
Network Structure ◽  
Success Factors ◽  
Research Community ◽  
Literature Survey ◽  
High Failure Rate ◽  
Software Projects ◽  
Critical Success ◽  
Insight Into

Whereas there are several instances of Open Source Software (OSS) projects that have achieved huge success in the market, a high failure rate has been reported for OSS projects. This study conducts a literature survey to gain insight into existing studies on the success of OSS projects. More specifically, this study seeks to extract the critical success factors for OSS projects. Based on the literature survey in this study, the authors found determinants of success in OSS projects and classified them into three broad categories of project traits, product traits, and network structure. These findings have important implications for both the OSS research community and OSS practitioners.

Research Regarding Embedded Systems of Robotic Technology for Manufacturing of Hybrid Polymeric Composite Products

2019 ◽  
Vol 957 ◽  
pp. 267-276
Author(s):  
Catalin Jianu ◽  
Giuseppe Lamanna ◽  
Constantin Gheorghe Opran
Keyword(s):  
Composite Materials ◽  
Feedback Loop ◽  
Polymeric Composite ◽  
Fiber Reinforced ◽  
Dynamic Adjustment ◽  
Reinforced Composite ◽  
Future Challenges ◽  
Processing Regimes ◽  
Manufacturing Technologies ◽  
Mechanical Cutting

Fiber-reinforced composite materials are increasingly present in areas such as automotive, aeronautics, defense, sport, used due to their special mechanical characteristics and very good behavior under heavy working conditions. New mold design techniques (such as 3D printing technologies), processing (such as the use of robotic technologies), open new opportunities for future challenges. This paper represents research on analysis techniques for the design of composite materials products made of fiber-reinforced, research on the use of devices with feedback loop for mechanical cutting technologies, which allow intelligent dynamic adjustment of the processing regimes, analysis of manufacturing technologies used as unconventional processes for the implementation of inclusion components, economic judgments on advantages, disadvantages of the techniques and methods used.

Sign in / Sign up

Export Citation Format

Share Document