scholarly journals Effect of Grain Size and Structure, Solid Solution Elements, Precipitates and Twinning on Nanohardness of Mg-RE Alloys

2013 ◽  
Vol 765 ◽  
pp. 491-495 ◽  
Author(s):  
Petra Maier ◽  
Asta Richter ◽  
Gerhard Tober ◽  
Norbert Hort
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Cold Work ◽  
Extrusion Direction ◽  
Hot Extrusion ◽  
Recrystallization Process ◽  
Average Grain Size ◽  
Second Phases ◽  
Inhomogeneous Microstructure ◽  
Isothermal Ageing

In this study Mg10GdxNd alloys are investigated by nanoindentation hardness measurements in several material conditions. Mg10GdxNd alloys with an average coarse grain size of 500 µm were cast by permanent mold direct chill casting. Hardness values vary due to the inhomogeneous microstructure formed during the solidification process consisting of dendrite arms with preferred orientation direction. The effect of dissolving particles during solution heat treatment (T4) and isothermal ageing (T6) was observed to a different extent depending on Nd content. Isothermal ageing promotes a duplex microstructure of coarse β1phase precipitates and regions containing much finer precipitates. Post processing by direct extrusion changes the microstructure dramatically to an average grain size of 15 µm. The microstructure after hot extrusion shows segregation of precipitates in the extrusion direction. Near this alignment of second phases hardness and plastic deformation differ from precipitates enriched in RE elements due to depleted regions of solid solution around them. This phenomenon is known from alloying element segregation to grain boundaries. Depending on the amount and location of second phases in the as-cast microstructure and degree of cold work, recrystallization leads to an inhomogeneous microstructure, consisting of fine grains (15 µm) and very fine grains, where second phases act as nuclei during the recrystallization process. Furthermore, mechanical testing (fatigue) causes an increase in dislocation density by work hardening and extensive twinning near the fractured surface. Here the hardening effect interferes with grain size strengthening.

Effects of Extrusion Ratio on Microstructures and Properties of Al-Cu-Mg-Ag-Ce-Er Alloy Wires

2017 ◽  
Vol 898 ◽  
pp. 191-198
Author(s):  
Yu Peng Xu ◽  
Ze Sheng Ji
Keyword(s):  
Grain Size ◽  
Tensile Strength ◽  
Dynamic Recrystallization ◽  
Hot Extrusion ◽  
Nucleation Mechanism ◽  
Extrusion Ratio ◽  
Average Grain Size ◽  
Second Phases ◽  
Grain Coalescence

The Al-Cu-Mg-Ag-Ce-Er alloy wires with different extrusion ratio (λ=12, 25, 50, 100) were produced by hot extrusion at 450oC. The effects of extrusion ratio on the microstructures, tensile strength and elongation of Al-Cu-Mg-Ag-Ce-Er alloy wires were researched by means of OM, SEM, TEM and mechanical test.The results show that with the extrusion ratio increasing, the average grain size decreased from 83μm to 42μm, the Al2Cu, Al8Cu4Ce and Al8Cu4Er phases was broken gradually, and the homogeneousdistribution about these second-phases in the alloy wires increased. The tensile strength increased from 366MPa to 459MPa with extrusion ratio, and the elongation initially decreased and then increased with the increase of extrusion ratio. Dynamic recrystallization for Al-Cu-Mg-Ag-Ce-Er alloy occurred at different extrusion ratios. Withincreasing of extrusion ratio, the main nucleation mechanism of dynamic recrystallization changed from the sub-grain coalescence at lower extrusion ratioto the acceleration of second-phases for nucleation at higher extrusion ratio.

Microstructure and Dynamic Ultra-Micro Hardness of the As-Cast and Extruded Mg-Al-Ca-Sm Alloys

2007 ◽  
Vol 26-28 ◽  
pp. 153-156 ◽  
Author(s):  
Hyeon Taek Son ◽  
Jae Seol Lee ◽  
Ji Min Hong ◽  
Dae Guen Kim ◽  
Kyosuke Yoshimi ◽  
...  
Keyword(s):  
Grain Size ◽  
Elevated Temperatures ◽  
Extrusion Direction ◽  
Hot Extrusion ◽  
Hardness Test ◽  
Eutectic Phase ◽  
Micro Hardness ◽  
Maximum Hardness ◽  
Average Grain Size ◽  
Cast Alloys

The as-cast microstructure of Mg-5Al-3Ca-2Sm alloy consists of equiaxed α-Mg matrix, (Mg, Al)2Ca eutectic phase and Al-Sm rich intermetallic compounds. This eutectic phase of the extruded alloys was elongated to extrusion direction and size of this phase was finered compare to that of as-cast alloys because of severe deformation during hot extrusion. After hot extrusion, the average grain size of Mg-5Al-3Ca and Mg-5Al-3Ca-2Sm alloys was 4.8 *m and 3.8 *m, respectively. In load-unload hardness test, penetration depth was decreased with added Sm and after extrusion procedure because of grain size refining by addition Sm and large deformation. Hardness value of the alloys containing Sm was higher than that of Mg-5Al-3Ca alloy due to grain refining and formation Al-Sm rich intermetallic compound at gain boundary and α-Mg matrix. Maximum hardness value was obtained at the extruded Mg-5Al-3Ca-2Sm alloy at elevated temperatures.

Precipitation Behavior and Strengthening Mechanism of Second Phases in AZ31-1.3Ca-1.0Sm-0.3La Alloy

2020 ◽  
Vol 993 ◽  
pp. 307-312
Author(s):  
Li Fu ◽  
Wen Xin Hu ◽  
Qi Chi Le ◽  
Zheng Jia
Keyword(s):  
Grain Size ◽  
Hot Extrusion ◽  
Strengthening Mechanism ◽  
Az31 Alloy ◽  
Precipitation Behavior ◽  
Grain Sizes ◽  
Average Grain Size ◽  
New Type ◽  
Second Phases ◽  
The Common

A new type of AZ31-1.3Ca-1.0Sm-0.3La alloy was obtained in this study by adding Ca, Sm and La to AZ31 alloy. Detailed analysis results on second phases showed that Al2Ca phases, Al2Sm phases with two kinds of morphologies formed in as-cast AZ31-1.3Ca-1.0Sm-0.3La alloy besides Mg17Al12 phases, and La atoms mainly dissolved in Al2Ca/Sm phases. The average grain size of as-cast AZ31-1.3Ca-1.0Sm-0.3La alloys was 212 μm and the grain sizes distributions were uniform. After the hot extrusion, the average grain size decreased to 5.4 μm and the grain sizes distributions were uneven. The base texture of as-extruded AZ31-1.3Ca-1.0Sm-0.3La alloy was strong, and the maximum density value was 3.25. The yield strength, ultimate tensile strength and elongation of as-extruded AZ31-1.3Ca-1.0Sm-0.3La alloy was 216 MPa, 280 MPa and 16% at RT, and 145 MPa, 188 MPa and 42% at 150°C, respectively, which are much higher than those of the common MB2 alloy both at the room temperature and 150 °C.

Effect of Warm Rolling on Microstructure and High Temperature Mechanical Behavior of a Nano-Structured Al-8Fe-2Mo-2V-1Zr Alloy

2005 ◽  
Vol 486-487 ◽  
pp. 411-414 ◽  
Author(s):  
Won Yong Kim ◽  
Jae Sung Park ◽  
Mok Soon Kim
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Elevated Temperatures ◽  
Hot Extrusion ◽  
Warm Rolling ◽  
Spray Forming ◽  
Grain Structure ◽  
Average Grain Size ◽  
Two Samples ◽  
Additional Process

Mechanical properties of a nano-structured Al-8Fe-2Mo-2V-1Zr alloy produced by spray forming and subsequent hot-extrusion at 420°C were investigated in terms of tensile test as a function of temperature. Warm rolling was adapted as an additional process to expect further refinement in microstructure. Well-defined equiaxed grain structure and finely distributed dispersoids with nano-scale in particle size were observed in the spray formed and hot extruded sample (as-received sample). The average grain size and particle size were measured to 500 nm and 50 nm, respectively. While it was found that warm rolling gives rise to precipitate fine dispersoids less than 10 nm without influencing the grain size of matrix phase, in the temperature range of RT∼150°C, distinguishable changes in ultimate tensile strength were not found between the as-received and warm-rolled samples. At elevated temperatures ranging from 350 to 550°C, warm-rolled sample showed a higher value of elongation than as-received one although similar values of elongation were observed between two samples at temperatures lower than 350°C.

scholarly journals Strong Interactions between Austenite and the Matrix of Medium-Mn Steel during Intercritical Annealing

Materials ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3366 ◽  
Author(s):  
Tianpeng Zhou ◽  
Cunyu Wang ◽  
Chang Wang ◽  
Wenquan Cao ◽  
Zejun Chen
Keyword(s):  
Grain Size ◽  
Annealing Temperature ◽  
Ferrite Matrix ◽  
Strong Interactions ◽  
Recrystallization Process ◽  
Austenite Grain Size ◽  
Recrystallization Kinetics ◽  
Average Grain Size ◽  
The Matrix ◽  
Austenite Grains

The effects of heat treatment on the microstructure evolution was studied in regards to austenite nucleation and grain growth. It was found that the austenite nucleation and matrix recrystallization kinetics of samples annealed at 675 °C for different times were revealed, implying a strong interaction between the ferrite matrix and austenite. The recrystallization of the matrix during annealing provided favorable conditions for austenite nucleation and growth, and the formation of austenite during this process reduced the matrix recrystallization kinetics, thus delaying the recrystallization process of the matrix around the austenite grains. The statistical results for the austenite grain size under different annealing temperatures indicated that the average grain size of the austenite slightly increases with increasing of the annealing temperature, but the austenite with the largest grain size grows faster at the same temperature. This difference is attributed to the strict Kurdjumov Sachs (KS) orientation relationship (OR) between the austenite grains and the matrix, because the growth of austenite with a strict KS OR with the matrix is often inhibited during annealing. In contrast, the austenite maintains a non-strict KS OR with the matrix and can grow preferentially with increasing annealing temperature and time.

Investigating the Relationships Between Structures and Properties of Al Alloys Incorporated With Ti and Mg Inclusions

2016 ◽  
Vol 138 (3) ◽  
Author(s):  
Halil Ibrahim Kurt ◽  
Ibrahim H. Guzelbey ◽  
Serdar Salman ◽  
Razamzan Asmatulu ◽  
Mustafa Dere
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Elevated Temperatures ◽  
Solidification Process ◽  
Optical Microscope ◽  
Industrial Applications ◽  
Al Alloys ◽  
Average Grain Size ◽  
Solidification Processes ◽  
Grain Size And Shape

This study investigates the influence of titanium (Ti) and magnesium (Mg) additions on aluminum (Al) alloys in order to evaluate the relationship between the structure and properties of the new alloys. The alloys obtained at elevated temperatures mainly consist of Al–2Mg–1Ti, Al–2Mg–3Ti, Al–4Mg–2Ti, and Al–6Mg–2Ti alloys, as well as α and τ solid solution phases of intermetallic structures. Microstructural analyses were performed using X-ray diffraction (XRD), optical microscope, and energy dispersive spectrometry (EDS) techniques. Test results show that the average grain size of the alloys decreased with the addition of Ti inclusions during the casting and solidification processes, and the smallest grain size was found to be 90 μm for the Al–6Mg–3Ti alloy. In addition, tensile properties of the Al–Mg–Ti alloys were initially improved and then worsened after the addition of higher concentrations of Ti. The highest tensile and hardness values of the alloys were Al–4Mg–2Ti (205 MPa) and Al–6Mg–3Ti (80 BHN). The primary reasons for having higher mechanical properties may be attributed to strengthening of the solid solution and refinement of the grain size and shape during the solidification process. For this study, the optimum concentrations of Ti and Mg added to the Al alloys were 4 and 2 wt.%, respectively. This study may be useful for field researchers to develop new classes of Al alloys for various industrial applications.

Research on Microstructure and Refining Effect of Al-3Ti-0.5B Master Alloy Produced with Ti Sponge

2011 ◽  
Vol 66-68 ◽  
pp. 845-849
Author(s):  
Xiao Wei Chen ◽  
Ya Gao ◽  
Hong Liang Zhao ◽  
Kang Rong Weng ◽  
Bao Feng Zhang
Keyword(s):  
Grain Size ◽  
Master Alloy ◽  
Molten Aluminum ◽  
Grain Refining ◽  
Commercial Purity ◽  
Average Grain Size ◽  
Feeding Methods ◽  
Refining Performance ◽  
Second Phases ◽  
Commercial Purity Aluminum

Al-3Ti-0.5B master alloy was prepared by reaction of Ti sponge, KBF4with aluminum melt. The morphology and distribution of the second phases effected by the feeding methods have been discussed. And the grain refining performance and the resistance to fading of the master alloy were investigated. The result shows that the Al-3Ti-0.5B master alloy which was prepared by adding mixture of Ti sponge and KBF4power into molten aluminum contains a large number of granular TiB2phase and blocky TiAl3phase. The average grain size of commercial purity aluminum was refined from 920μm to 120μm by adding 0.5wt.% of the master alloy. And the refining performance of the master alloy shows no obviously fading phenomenon when the holding time up to 30min.

Influence of Annealing Time on Microstructure of Ni-W Alloys

2013 ◽  
Vol 747-748 ◽  
pp. 613-618
Author(s):  
Qiao Zhang ◽  
Shu Hua Liang ◽  
Chen Zhang ◽  
Jun Tao Zou
Keyword(s):  
Electron Microscopy ◽  
Solid Solution ◽  
Grain Size ◽  
Grain Boundaries ◽  
Annealing Time ◽  
Single Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Average Grain Size ◽  
Scanning Electron

The as-cast Ni-W alloys with 15wt%W, 25wt%W and 30wt%W were annealed in hydrogen at 1100. The effect of the annealing time on the microstructure of Ni-W alloys was studied, and the phase constituents and microstructure of annealed Ni-W alloys were characterized by the X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results showed that no any phase changed for Ni-15%W, Ni-25%W and Ni-30%W alloys annealed for 60 min, 90 min and 150 min, which were still consisted of single-phase Ni (W) solid solution. However, microstructure had a significant change after annealing. With increase of annealing time, the microstructure of Ni-15%W alloy became more uniform after annealing for 90 min, and the average grain size was 95μm, whereas the grain size of Ni-15%W alloy increased significantly after annealing for 150 min. For Ni-25%W and Ni-30%W, there was no obvious change on the grain size with increase of annealing time, and the amount of oxides at grain boundaries gradually reduced. After annealing for 150 min, the impurities at grain boundaries almost disappeared. Subsequently, the annealing at 1100 for 150 min was beneficial for the desired microstructure of Ni-25%W and Ni-30%W alloys.

Effect of Annealing Time on the Microstructure and Texture of Interstitial Free Steel

2012 ◽  
Vol 535-537 ◽  
pp. 593-596
Author(s):  
Zhi Fen Wang ◽  
Rong Dong Han ◽  
Shun Bing Zhou ◽  
Zhong Hai Yao ◽  
Li Xin Wu
Keyword(s):  
Grain Size ◽  
Annealing Time ◽  
Electron Backscatter Diffraction ◽  
Recrystallization Process ◽  
Interstitial Free ◽  
X Ray Diffraction ◽  
Steel Sheets ◽  
Grain Boundary Character ◽  
Average Grain Size ◽  
Backscatter Diffraction

Effect of annealing time on the microstructure and texture of IF steel sheets was investigated. Average grain size, grain boundary character and recrystallization texture were measured by X-ray diffraction (XRD) and electron backscatter diffraction (EBSD) in order to clarify the effect of annealing time on microstructure of recrystallization process. The average grain size increased with increasing annealing time. With rising annealing time, the number of low angle boundary (0～15o) decreased due to the mergence of grain with sub-boundary. The //ND (-fiber) pole intensity had a highest value annealed at 60s. The annealing time played an important role in recrystallization process which affected the mechanical properties and microstructure of IF steels.

scholarly journals Effects of Repetitive Upsetting Extrusion on the Microstructure and Texture of GWZK124 Alloy under Different Starting Temperatures

Materials ◽  
2019 ◽  
Vol 12 (15) ◽  
pp. 2437
Author(s):  
Guanshi Zhang ◽  
Zhimin Zhang ◽  
Yingze Meng ◽  
Zhaoming Yan ◽  
Xin Che ◽  
...  
Keyword(s):  
Grain Size ◽  
Dynamic Recrystallization ◽  
Grain Refinement ◽  
Volume Fraction ◽  
Bimodal Microstructure ◽  
Continuous Dynamic Recrystallization ◽  
Average Grain Size ◽  
Second Phases ◽  
Continuous Dynamic ◽  
Weak Texture

The effects of repetitive upsetting extrusion under different starting temperatures on the microstructure and texture of GWZK124 alloy were investigated. The results clearly showed that the particles and second phases induced dynamic recrystallization (DRX), which can be explained by the particle-stimulated nucleation (PSN) mechanism. It was shown that grain refinement during repetitive upsetting extrusion (RUE) is dominated by a complicated combination of continuous dynamic recrystallization and discontinuous dynamic recrystallization. The RUEed alloys under different starting temperatures exhibited a bimodal microstructure comprising fine DRXed grains with weak texture and coarse deformed grains with strong texture. The DRXed grains could weaken the texture. As the RUE starting temperature decreased, the average grain size increased and the volume fraction of DRXed grains decreased.

Sign in / Sign up

Export Citation Format

Share Document