scholarly journals Effect of Tempering on Microstructure and Mechanical Properties of Laser Welded and Post-Weld Treated AHSS Specimens

2017 ◽  
Vol 891 ◽  
pp. 18-24
Author(s):  
Farnoosh Forouzan ◽  
Nanny Strandqvist ◽  
Esa Vuorinen ◽  
Erik Navara ◽  
Frank Mücklich
Keyword(s):  
Mechanical Properties ◽  
Precipitation Hardening ◽  
High Strength ◽  
Tensile Tests ◽  
Significant Loss ◽  
Hardness Profile ◽  
Microstructure Development ◽  
Notable Effect ◽  
Significant Difference ◽  
Thermal Stability Of

An advanced high strength steel (0.08 %C, 1.79 %Mn, 0.23 %Si) was subjected to different post-weld heat treatments by quenching & tempering treatments (Q&T) after laser welding to reduce the risk of martensite formation in a few seconds based on an idea of quench and partitioning (Q&P), mechanism. The thermal stability of retained austenite, microstructure development and mechanical properties have been studied at 2 tempering temperatures of 440°C (Ms) and 636°C (Bs), both for 15 minutes, by means of electron microscopy, dilatometry, hardness profile and tensile tests. Dilatometer study unveiled that redistribution of carbon atoms and precipitation of transition carbides occur around 150°C and austenite decomposition occur at 600°C. Tempering at 636°C resulted in notable effect on the mechanical properties, while no significant difference was detected at 440°C, except a slight hardness drop. The strength increased up to 12% for the different specimens without significant loss in ductility for all specimens tempered at 636°C, which may be caused by precipitation hardening and recrystallization of martensite lath boundaries during tempering around 600°C.

JESSOP JS17Cr-4Ni

Alloy Digest ◽  
1982 ◽  
Vol 31 (7) ◽  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Food Processing ◽  
Precipitation Hardening ◽  
High Strength ◽  
Heat Treating ◽  
Steel Company ◽  
Lower Strength ◽  
Nickel Copper ◽  
Short Time

Abstract JESSOP JS17Cr-4Ni is a martensitic, precipitation-hardening chromium-nickel-copper stainless steel. It provides an excellent combination of high strength and hardness, short-time low-temperature precipitation hardening and good mechanical properties at temperatures up to 600 F (316 C). Its corrosion resistance is quite good but inferior to lower strength grades produced for corrosion-resistance applications. JS17Cr-4Ni is used widely for critical applications in the aerospace, chemical, food processing and other industries. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on corrosion resistance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SS-412. Producer or source: Jessop Steel Company.

Mechanical Properties and Aging Behavior of Ultrafine Grained Al-Ag Alloy Fabricated by Accumulative Roll-Bonding

2014 ◽  
Vol 794-796 ◽  
pp. 851-856
Author(s):  
Tadashiege Nagae ◽  
Nobuhiro Tsuji ◽  
Daisuke Terada
Keyword(s):  
Mechanical Properties ◽  
Grain Refinement ◽  
Accumulative Roll Bonding ◽  
Precipitation Hardening ◽  
Tensile Elongation ◽  
Solution Treatment ◽  
High Strength ◽  
Subsequent Aging ◽  
Roll Bonding ◽  
Ultrafine Grained

Accumulative roll-bonding (ARB) process is one of the severe plastic deformation processes for fabricating ultrafine grained materials that exhibit high strength. In aluminum alloys, aging heat treatment has been an important process for hardening materials. In order to achieve good mechanical properties through the combination of grain refinement hardening and precipitation hardening, an Al-4.2wt%Ag binary alloy was used in the present study. After a solution treatment at 550°C for 1.5hr, the alloy was severely deformed by the ARB process at room temperature (RT) up to 6 cycles (equivalent strain of 4.8). The specimens ARB-processed by various cycles (various strains) were subsequently aged at 100, 150, 200, 250°C, and RT. The hardness of the solution treated (ST) specimen increased by aging. On the other hand, hardness of the ARB processed specimen decreased after aging at high temperatures such as 250°C. This was probably due to coarsening of precipitates or/and matrix grains. The specimen aged at lower temperature showed higher hardness. The maximum harnesses achieved by aging for the ST specimen, the specimens ARB processed by 2 cycles, 4 cycles and 6 cycles were 55HV, 71HV, 69HV and 65HV, respectively. By tensile tests it was shown that the strength increased by the ARB process though the elongation decreased significantly. However, it was found that the tensile elongation of the ARB processed specimens was improved by aging without sacrificing the strength. The results suggest that the Al-Ag alloy having large elongation as well as high strength can be realized by the combination of the ARB process for grain refinement and the subsequent aging for precipitation hardening.

scholarly journals Controlling the Thermal Stability of Kyanite-Based Refractory Geopolymers

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 2903
Author(s):  
Juvenal Giogetti Nemaleu Deutou ◽  
Rodrigue Cyriaque Kaze ◽  
Elie Kamseu ◽  
Vincenzo M. Sglavo
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
High Strength ◽  
Treatment Temperature ◽  
Strength Development ◽  
Particle Sizes ◽  
Cold Setting ◽  
Thermal Stability Of ◽  
Geopolymer Composites ◽  
Refractory Composites

The present project investigated the thermal stability of cold-setting refractory composites under high-temperature cycles. The proposed route dealt with the feasibility of using fillers with different particle sizes and studying their influence on the thermo-mechanical properties of refractory geopolymer composites. The volumetric shrinkage was studied with respect to particle sizes of fillers (80, 200 and 500 µm), treatment temperature (1050–1250 °C) and amount of fillers (70–85 wt.%). The results, combined with thermal analysis, indicated the efficiency of refractory-based kyanite aggregates for enhancing thermo-mechanical properties. At low temperatures, larger amounts of kyanite aggregates promoted mechanical strength development. Flexural strengths of 45, 42 and 40 MPa were obtained for geopolymer samples, respectively, at 1200 °C, made with filler particles sieved at 80, 200 and 500 µm. In addition, a sintering temperature equal to 1200 °C appeared beneficial for the promotion of densification as well as bonding between kyanite aggregates and the matrix, contributing to the reinforcement of the refractory geopolymer composites without any sign of vitrification. From the obtained properties of thermal stability, good densification and high strength, kyanite aggregates are efficient and promising candidates for the production of environmentally friendly, castable refractory composites.

Investigations on the Mechanical Properties and Formability of Friction Stir Welded Tailored Blanks

2007 ◽  
Vol 344 ◽  
pp. 143-150 ◽  
Author(s):  
Gianluca Buffa ◽  
Livan Fratini ◽  
Marion Merklein ◽  
Detlev Staud
Keyword(s):  
Mechanical Properties ◽  
Stress Condition ◽  
Research Effort ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Friction Stir ◽  
Tailored Blanks ◽  
Sheet Stamping ◽  
Wide Range

Tight competition characterizing automotive industries in the last decades has determined a strong research effort aimed to improve utilized processes and materials in sheet stamping. As far as the latter are regarded light weight alloys, high strength steels and tailored blanks have been increasingly utilized with the aim to reduce parts weight and fuel consumptions. In the paper the mechanical properties and formability of tailored welded blanks made of a precipitation hardenable aluminum alloy but with different sheet thicknesses, have been investigated: both laser welding and friction stir welding have been developed to obtain the tailored blanks. For both welding operations a wide range of the thickness ratios has been considered. The formability of the obtained blanks has been characterized through tensile tests and cup deep drawing tests, in order to show the formability in dependency of the stress condition; what is more mechanical and metallurgical investigations have been made on the welded joints.

scholarly journals Experimental Investigation into Corrosion Effect on Mechanical Properties of High Strength Steel Bars under Dynamic Loadings

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Hui Chen ◽  
Jinjin Zhang ◽  
Jin Yang ◽  
Feilong Ye
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Strength Steel ◽  
High Strength ◽  
Tensile Tests ◽  
Reinforcing Steel ◽  
Test Results ◽  
Cross Sectional ◽  
Steel Bars

The tensile behaviors of corroded steel bars are important in the capacity evaluation of corroded reinforced concrete structures. The present paper studies the mechanical behavior of the corroded high strength reinforcing steel bars under static and dynamic loading. High strength reinforcing steel bars were corroded by using accelerated corrosion methods and the tensile tests were carried out under different strain rates. The results showed that the mechanical properties of corroded high strength steel bars were strain rate dependent, and the strain rate effect decreased with the increase of corrosion degree. The decreased nominal yield and ultimate strengths were mainly caused by the reduction of cross-sectional areas, and the decreased ultimate deformation and the shortened yield plateau resulted from the intensified stress concentration at the nonuniform reduction. Based on the test results, reduction factors were proposed to relate the tensile behaviors with the corrosion degree and strain rate for corroded bars. A modified Johnson-Cook strength model of corroded high strength steel bars under dynamic loading was proposed by taking into account the influence of corrosion degree. Comparison between the model and test results showed that proposed model properly describes the dynamic response of the corroded high strength rebars.

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

The Structure and Mechanical Properties of Plastically Consolidated Al-Ni Alloy

2016 ◽  
Vol 682 ◽  
pp. 245-251 ◽  
Author(s):  
Grzegorz Włoch ◽  
Tomasz Skrzekut ◽  
Jakub Sobota ◽  
Antoni Woźnicki ◽  
Justyna Cisoń
Keyword(s):  
Mechanical Properties ◽  
Vickers Hardness ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Intermetallic Phases ◽  
Scanning Calorimetry ◽  
Porosity Formation ◽  
X Ray ◽  
Ni Alloy ◽  
Thermal Stability Of

Mixed and preliminarily consolidated powders of aluminium and nickel (90 mass % Al and 10 mass % Ni) were hot extruded. As results the rod, 8 mm in diameter, was obtained. As-extruded material was subjected to the microstructural investigations using scanning electron microscopy (SEM/EDS) and X-ray analysis (XRD). The differential scanning calorimetry (DSC) and thermo-mechanical analysis (TMA) were also performed. The mechanical properties of as extruded material were determined by the tensile test and Vickers hardness measurements. In order to evaluate the thermal stability of PM alloy, samples were annealed at the temperature of 475 and 550 °C. After annealing Vickers hardness measurements and tensile tests were carried out. The plastic consolidation of powders during extrusion was found to be very effective, because no pores or voids were observed in the examined material. The detailed microstructural investigations and XRD analyses did not reveal the presence of the intermetallic phases in the as-extruded material. During annealing, the Al3Ni intermetallic compound was formed as the result of chemical reaction between the alloy components. The hardness of the alloy after annealing at the temperature of 475°C was found to be comparable to the hardness in as-extruded state. Annealing of the material at the temperature of 550°C results in hardness decreasing by about 50%, as the consequence of porosity formation and Al3Ni cracking.

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

Comparison of Microstructure and Mechanical Properties of Additively Manufactured and Conventional Maraging Steel

2020 ◽  
Vol 405 ◽  
pp. 133-138
Author(s):  
Ludmila Kučerová ◽  
Andrea Jandová ◽  
Ivana Zetková
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Maraging Steel ◽  
Precipitation Hardening ◽  
High Strength ◽  
Hardness Measurement ◽  
Nickel Steel ◽  
Heat Treated ◽  
Good Material ◽  
Iron Nickel

Maraging steel is an iron-nickel steel alloy, which achieves very good material properties like high toughness, hardness, good weldability, high strength and dimensional stability during heat treatment. In this work, maraging steel 18Ni-300 was manufactured by selective laser melting. It is a method of additive manufacturing (AM) technology, which produces prototypes and functional parts. Sample of additively manufactured and conventional steel with the same chemical composition were tested after in three different states – heat treated (as-built/as-received), solution annealed and precipitation hardened. Resulting microstructures were analysed by light and scanning electron microscopy and mechanical properties were obtained by hardness measurement and tensile test. Cellular martensitic microstructures were observed in additively manufactured samples and conventional maraging steel consisted of lath martensitic microstructures. Very similar mechanical properties were obtained for both steels after the application of the same heat treatment. Ultimate tensile strengths reached 839 – 900 MPa for samples without heat treatment and heat treated by solution annealing, the samples after precipitation hardening had tensile strengths of 1577 – 1711 MPa.

Effect of Quenching and Partitioning Processing on Microstructure and Mechanical Properties of a Low Alloyed Steel

2018 ◽  
Vol 941 ◽  
pp. 52-57
Author(s):  
Bernd Pfleger ◽  
Marina Gruber ◽  
Gerald Ressel ◽  
Peter Gruber ◽  
Matthew Galler ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Phase Evolution ◽  
Tensile Tests ◽  
Austenite Phase ◽  
Phase Fraction ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Low Alloyed Steel ◽  
A Minor

The concept of quenching and partitioning (Q&P) is a tool to generate steels with high strength and high ductility resulting from a relatively high amount of martensite and austenite. As the parameters of the Q&P treatment influence the strength and ductility properties, the goal of this work was to analyze the effects of varying quenching and partitioning temperatures on the phase evolution, on the retained austenite phase fraction and on the mechanical properties. The phase evolution during heat treatment was analyzed by dilatometer and the microstructure after processing was characterized by light microscopy in combination with color etching according to Klemm. The austenite phase fraction and its carbon content were determined by X-Ray diffraction and the mechanical properties were evaluated by tensile tests. It is shown that the quenching temperature has a minor impact on the phase fraction of austenite as well as its stabilization by carbon and thus, also the mechanical properties. Furthermore, austenite transformation during the partitioning treatment is illustrated.

Sign in / Sign up

Export Citation Format

Share Document