Performance Properties of Irradiated Recycled Polypropylene as a Compatibilizer in Recycled Polypropylene/Microcrystalline Cellulose Composites

2017 ◽  
Vol 894 ◽  
pp. 62-65 ◽  
Author(s):  
Noorasikin Samat ◽  
Nurul Hakimah Mohd Lazim ◽  
S.N.R. Motsidi ◽  
Noor Azlina Hassan
Keyword(s):  
Thermal Stability ◽  
Electron Beam ◽  
Microcrystalline Cellulose ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Recycled Polypropylene ◽  
Cellulose Composites ◽  
Degradation Tests ◽  
Twin Screw ◽  
Surface Observations

Effects of irradiated rPP compatibilizer, on the mechanical and thermal properties of recycled polypropylene/microcrystalline cellulose composites (rPP/MCC), are investigated. rPP is irradiated with an electron beam at dosages ranging from 10, 20, 30 to 50kGy. A matrix, containing of unirradiated and irradiated rPP (50:50 by ratio), is then added to 5, 20 and 40wt% MCC fibres. The composites are prepared using a twin screw extruder, followed by injection moulding. The properties are then characterized using tensile and thermal degradation tests. The improvement of Young’s modulus by up to about 45% suggests a compatibilising effect of the irradiated rPP. Fracture surface observations reveal an adhesion between rPP matrix and MCC fibres. However, the thermal stability deteriorated with the addition of MCC and irradiated rPP.

Mechanical and thermal characterization of grafted PP-NCC nanocomposites

2019 ◽  
pp. 089270571987822
Author(s):  
Saud Aldajah ◽  
Mohammad Y Al-Haik ◽  
Waseem Siddique ◽  
Mohammad M Kabir ◽  
Yousef Haik
Keyword(s):  
Thermal Properties ◽  
Interfacial Adhesion ◽  
Thermal Characterization ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Scanning Calorimetry ◽  
Three Point Bending ◽  
Twin Screw ◽  
Thermal Stability Of

This study reveals the enhancement of mechanical and thermal properties of maleic anhydride-grafted polypropylene (PP- g-MA) with the addition of nanocrystalline cellulose (NCC). A nanocomposite was manufactured by blending various percentages of PP, MA, and NCC nanoparticles by means of a twin-screw extruder. The influence of varying the percentages of NCC on the mechanical and thermal behavior of the nanocomposite was studied by performing three-point bending, nanoindentation, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and Fourier-transform infrared (FTIR) spectroscopy tests. The novelty of this study stems on the NCC nanoparticles and their ability to enhance the mechanical and thermal properties of PP. Three-point bending and nanoindentation tests revealed improvement in the mechanical properties in terms of strength, modulus, and hardness of the PP- g-MA nanocomposites as the addition of NCC increased. SEM showed homogeneity between the mixtures which proved the presence of interfacial adhesion between the PP- g-MA incorporated with NCC nanoparticles that was confirmed by the FTIR results. DSC and TGA measurements showed that the thermal stability of the nanocomposites was not compromised due to the addition of the coupling agent and reinforced nanoparticles.

Behaviour of PLA/POSS nanocomposites: Effects of filler content, functional group and copolymer compatibilization

2021 ◽  
pp. 096739112110080
Author(s):  
Yelda Meyva Zeybek ◽  
Cevdet Kaynak
Keyword(s):  
Functional Group ◽  
Filler Content ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Grafted Copolymer ◽  
Before And After ◽  
Twin Screw ◽  
Oligomeric Silsesquioxane ◽  
Matrix Nanocomposites

The main purpose of this study was to investigate influences of three parameters on the mechanical and thermal properties of the polylactide (PLA) matrix nanocomposites filled with polyhedral oligomeric silsesquioxane (POSS) particles. For the first parameter of “Filler Content”, nanocomposites with 1, 3, 5, 7 wt% basic POSS structure were compared. For the second parameter of “Functional Group,” basic POSS structure having only nonpolar isobutyl groups were compared with three other functionalized POSS structures; i.e. aminopropylisobutyl-POSS (ap-POSS), propanediolisobutyl-POSS (pd-POSS) and octasilane-POSS (os-POSS). Finally, for the third parameter of “Copolymer Compatibilization,” all specimens were compared before and after their maleic anhydride (MA) grafted copolymer compatibilization. Specimens were produced with twin-screw extruder melt mixing and shaped under compression molding. Various tests and analyses indicated that the optimum filler content for the improved mechanical properties was 1 wt%; while the optimum structure for strength and modulus was pd-POSS structure, in terms of fracture toughness it was basic POSS structure. Additional use of MA compatibilization was especially effective for the basic POSS and os-POSS particles.

NATURAL RUBBER/MICROCRYSTALLINE CELLULOSE COMPOSITES WITH EPOXIDIZED NATURAL RUBBER AS COMPATIBILIZER

2019 ◽  
Vol 92 (2) ◽  
pp. 378-387 ◽  
Author(s):  
Kumarjyoti Roy ◽  
Subhas Chandra Debnath ◽  
Aphiwat Pongwisuthiruchte ◽  
Pranut Potiyaraj
Keyword(s):  
Natural Rubber ◽  
Microcrystalline Cellulose ◽  
Interfacial Interaction ◽  
Probable Mechanism ◽  
Mechanical And Thermal Properties ◽  
Solvent Uptake ◽  
Cellulose Composites ◽  
Mechanism Of Interaction ◽  
Thermal Stability Of ◽  
Rubber Filler

ABSTRACT An exploration of the effect of epoxidized NR with 50 mole% epoxide groups (ENR-50) as compatibilizer on the rubber–filler interaction of microcrystalline cellulose (MCC)-filled NR composites was conducted. The compatibilizing efficiency of ENR-50 was systematically examined in terms of cure and mechanical and thermal properties of NR/MCC composites. ENR-50 compatibilized NR/MCC composites showed moderate enhancement in the maximum rheometric torque and tensile properties compared to either uncompatibilized NR/MCC composite or unfilled NR system. The solvent uptake measurements indicated improved interfacial interaction between NR matrix and MCC in presence of ENR-50 as compatibilizer. A thermogravimetric analysis confirmed excellent improvement in the thermal stability of NR/MCC composite in the presence of ENR-50 as compatibilizer. Fourier transform infrared spectroscopy was used to explain the probable mechanism of interaction between NR matrix and MCC in the presence of ENR-50.

Morphology and Properties of Polyoxymethylene/Polypropylene/Microcrystalline Cellulose Composites

2017 ◽  
Vol 751 ◽  
pp. 264-269
Author(s):  
Nipawan Yasumlee ◽  
Sirirat Wacharawichanant
Keyword(s):  
Thermal Stability ◽  
Microcrystalline Cellulose ◽  
Decomposition Temperature ◽  
Sem Analysis ◽  
Morphological Properties ◽  
Melt Mixing ◽  
Cellulose Composites ◽  
The Difference ◽  
Pp Blends ◽  
Internal Mixer

The effects of microcrystalline cellulose (MCC) on mechanical, thermal and morphological properties of polyoxymethylene (POM)/polypropylene (PP) blends at different compositions were investigated. The blends and composites were prepared by melt mixing using an internal mixer at 200°C. Scanning electron microscopy (SEM) analysis revealed phase separation between POM and PP phases due to the difference in polarity of POM and PP. When adding the MCC in the blends the morphology slightly changed due to the weak interaction between MCC and polymer phases. Incorporation of MCC at 5 phr could improve Young’s modulus of POM/PP blends. The storage modulus of the blends was improved after adding MCC 5 phr due to reinforcing effect of the MCC. The thermal properties found that the addition of MCC had no effect on the melting temperature of the blends. The blends exhibited higher decomposition temperature than pure POM. The blends showed the decomposition temperatures increased when increasing amount of PP content, which were higher than pure POM. Therefore, it may be inferred that the addition of PP could enhance the thermal stability of the POM/PP blends, but the addition of MCC did not improve the thermal stability.

Performance of polylactide against UV irradiation: Synergism of an organic UV absorber with micron and nano-sized TiO2

2020 ◽  
Vol 54 (18) ◽  
pp. 2489-2504 ◽  
Author(s):  
Ulas Can ◽  
Cevdet Kaynak
Keyword(s):  
Weight Loss ◽  
Thermal Properties ◽  
Uv Irradiation ◽  
Chemical Structure ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Uv Absorber ◽  
Fluorescent Lamps ◽  
Twin Screw

The main purpose of this study was to investigate mechanical and thermal performance of polylactide specimens against UV irradiation; first when only adding benzotriazole benzotriazole-based organic UV absorber (UVA), micro (200 nm) and nano (50 nm) sized titania (TiO2) particles alone, and then to reveal possible synergism when they are added together. Compounds were prepared by twin-screw extruder melt mixing, while the 2 mm thick specimens were shaped by compression molding. Specimens were exposed to UV irradiation under fluorescent lamps (UVB-313) with 0.50 W/m2 for the periods of 12 and 24 days. Changes in the performance of UV irradiated specimens were evaluated in terms of % weight loss, changes in color and chemical structure, including the decreases in the mechanical and thermal properties. Various tests and analysis revealed that synergistic benefits of using micro and nano TiO2 particles together with benzotriazole-type UVA were not only due to the effective stiffening, strengthening and toughening actions of titania particles, but also due to their very significant “UV screening” actions absorbing the photons of the UV irradiation, thus decreasing the degree of the detrimental photodegradation reactions leading to chain scissions in their PLA matrix.

scholarly journals Preparation of Graphene Oxide/Cellulose Composites with Microcrystalline Cellulose Acid Hydrolysis Using the Waste Acids Generated by the Hummers Method of Graphene Oxide Synthesis

Polymers ◽  
2021 ◽  
Vol 13 (24) ◽  
pp. 4453
Author(s):  
Yuanyuan Miao ◽  
Xiuya Wang ◽  
Yixing Liu ◽  
Zhenbo Liu ◽  
Wenshuai Chen
Keyword(s):  
Thermal Stability ◽  
Graphene Oxide ◽  
Microcrystalline Cellulose ◽  
Hydrophobic Property ◽  
Hummers Method ◽  
High Temperature Reaction ◽  
Cellulose Composites ◽  
Freeze Dried ◽  
Strong Acidity ◽  
Better Than

The Hummers method is the most commonly used method to prepare graphene oxide (GO). However, many waste acids remain in the raw reaction mixture after the completion of this reaction. The aim of this study was to reuse these waste acids efficiently. In this study, microcrystalline cellulose (MCC) was directly dissolved in the mixture after the high-temperature reaction of the Hummers method. The residual acid was used to hydrolyze MCC, and the graphene oxide/microcrystalline cellulose (GO/MCC) composites were prepared, while the acid was reused. The effects of MCC addition (0.5 g, 1.0 g, and 1.5 g in 20 mL) on the properties of the composites were discussed. The structure, composition, thermal stability, and hydrophobicity of GO/MCC composites were characterized and tested by SEM, XRD, FTIR, TG, and contact angle tests. The results showed that MCC could be acid hydrolyzed into micron and nano-scale cellulose by using the strong acidity of waste liquid after GO preparation, and it interacted with the prepared GO to form GO/MCC composites. When the addition amount of MCC was 1 g, the thermal stability of the composite was the highest due to the interaction between acid-hydrolyzed MCC and GO sheets. At the same time, the hydrophobic property of the GO/MCC composite is better than that of the GO film. The freeze-dried GO/MCC composites are more easily dispersed in water and have stronger stability.

Structure and Properties of Recycled Aromatic Thermoplastic Polyester Nanocomposites

2012 ◽  
Vol 527 ◽  
pp. 44-49
Author(s):  
Remo Merijs Meri ◽  
Janis Zicans ◽  
Tatjana Ivanova ◽  
Rita Berzina ◽  
Guntis Japins ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Mechanical And Thermal Properties ◽  
Structure And Properties ◽  
Screw Extruder ◽  
Melt Compounding ◽  
Weight Content ◽  
Recycled Polyethylene ◽  
Twin Screw ◽  
Nanofiller Content ◽  
Montmorillonite Nanoclay

Structure as well as mechanical and thermal properties of the nanocomposites based on recycled polyethylene terephthalate (RPET) are investigated. 1, 2 and 5 wt. % of unmodified montmorillonite nanoclay (MMT) were introduced in the RPET matrix by melt compounding in a twin screw extruder. Results of the investigations testify that optimum content of MMT for modification of RPET is between 1 and 2 wt. %. Up to this nanofiller weight content, the most rapid increase of stiffness, strength and impact toughness is observed. Besides it, at this nanofiller weight content the investigated composite have somewhat improved thermal resistance. It is demonstrated that the improvement of these properties is due to better distribution of MMT in the polymer matrix. At higher nanofiller content, the undesirable effects of the nanofiller agglomeration becomes more important.

Effects of Halloysite Nanotubes on Mechanical and Thermal Stability of Poly(Ethylene Terephthalate)/Polycarbonate Nanocomposites

2015 ◽  
Vol 735 ◽  
pp. 8-12
Author(s):  
Nurul Ain Jamaludin ◽  
Azman Hassan ◽  
Norhayani Othman ◽  
Mohammad Jawaid
Keyword(s):  
Thermal Stability ◽  
Ethylene Terephthalate ◽  
Flexural Modulus ◽  
Halloysite Nanotubes ◽  
Mechanical And Thermal Properties ◽  
Poly Ethylene Terephthalate ◽  
Twin Screw ◽  
Poly Ethylene ◽  
The Impact ◽  
Thermal Stability Of

The objective of this study is to investigate the effect of halloysite nanotubes (HNTs) loading on mechanical and thermal properties of poly(ethylene terephthalate)/polycarbonate (PET/PC) nanocomposites. Nanocomposites containing 70PET/30PC and 2-8 phr HNTs were prepared by twin screw extruder followed by injection moulding. As the percentage of HNTs increased, the flexural modulus increased. However, the flexural strength decreased with increasing HNTs content. The impact strength also decreased when HNTs increased. Thermogravimetry analysis of PET/PC/HNTs nanocomposites showed higher thermal stability at high HNTs content. However, on further addition of HNTs up to 8 phr, thermal stability of the nanocomposites decreased due to the poor dispersion of HNTs.

Sign in / Sign up

Export Citation Format

Share Document