Growth, Optical Adsorption and Resistivity of (Ga0.6In0.4)2Se3 and (Ga0.594In0.396Er0.01)2Se3 Single Crystals

2013 ◽  
Vol 200 ◽  
pp. 50-53
Author(s):  
Inna A. Ivashchenko ◽  
Volodumur V. Halyan ◽  
Irina V. Danylyuk ◽  
Volodumur Z. Pankevuch ◽  
Georgij Y. Davydyuk ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Phase Diagram ◽  
Differential Thermal Analysis ◽  
Band Gap ◽  
Single Crystals ◽  
Optical Band Gap ◽  
X Ray Diffraction ◽  
X Ray ◽  
Vertical Bridgman ◽  
Xrd Method

The phase diagram of the Ga2Se3–In2Se3 system was investigated by differential-thermal analysis (DTA) and X-ray diffraction (XRD) method. The single crystals from the area of existence of the γ2 phase with the compositions (Ga0.6In0.4)2Se3 and (Ga0.594In0.396Er0.01)2Se3 were grown by a vertical Bridgman method. Absorption spectra of the grown crystals were studied. The estimated optical band gap is 1.95±0. 01 eV. The resistance of the single crystals of (Ga0.6In0.4)2Se3 (R=500 MΩ) and (Ga0.594In0.396Er0.01)2Se3 (R=210 MΩ) was measured.

Revised phase diagram for the Nd–Pt system from 35 to 85 at% platinum

2010 ◽  
Vol 43 (1) ◽  
pp. 33-37 ◽  
Author(s):  
Ch. F. Xu ◽  
Z. F. Gu ◽  
G. Cheng ◽  
H. Y. Zhou ◽  
Z. M. Wang ◽  
...  
Keyword(s):  
Thermal Analysis ◽  
Phase Diagram ◽  
Differential Thermal Analysis ◽  
Binary System ◽  
Homogeneity Range ◽  
Low Temperatures ◽  
Polymorphic Transformation ◽  
Structure Type ◽  
X Ray Diffraction ◽  
X Ray

The phase diagram of the Nd–Pt system from 35 to 85 at%Pt has been revised using X-ray diffraction and differential thermal analysis. It is found that the Nd3Pt4phase with the rhombohedral Pd4Pu3structure type is unstable and decomposes into the two neighboring phases NdPt and NdPt2at temperatures ranging approximately from 583 to 1123 K. It is confirmed that the homogeneity range for the Laves phase NdPt2extends from about 68.5 to 75.3 at%Pt in the Nd–Pt binary system. The polymorphic transformation temperature of α-NdPt ⇌ β-NdPt is about 623 K, where the α-NdPt phase with BFe type is stable at low temperatures and the β-NdPt phase with BCr type at high temperatures.

Crystal growth and structure analysis of Sm2−xCexCuO4

2000 ◽  
Vol 15 (9) ◽  
pp. 1905-1910 ◽  
Author(s):  
H. Takeda ◽  
M. Okuno ◽  
M. Ohgaki ◽  
K. Yamashita ◽  
T. Matsumoto
Keyword(s):  
Crystal Structure ◽  
Thermal Analysis ◽  
Phase Diagram ◽  
Differential Thermal Analysis ◽  
Floating Zone ◽  
X Ray Diffraction ◽  
Zone Method ◽  
Floating Zone Method ◽  
X Ray ◽  
Quench Method

The phase diagram of the Sm2O3–CuO system was investigated by the combination of the differential thermal analysis and the quench method. The results showed that Sm2CuO4 incongruently melts at about 1220 °C, and that the solid Sm2CuO4 exists in equilibrium with the liquid consisting of 81–95 mol% CuO in the range of 1060–1220 °C. On the basis of the phase diagram, Sm2−xCexCuO4 single crystals were grown by the traveling solvent floating zone method. The crystal structure [space group I4/mmm, a = 3.917(1), c 4 11.899(2) Å] has been refined using single-crystal x-ray diffraction data with a precision corresponding to an R index of 0.02.

PENINGKATAN LAJU DISOLUSI ACYCLOVIR DENGAN METODE SISTEM DISPERSI PADAT MENGGUNAKAN POLOXAMER 188

2016 ◽  
Vol 5 (1) ◽  
pp. 6
Author(s):  
Budi Setiawan ◽  
Erizal Zaini ◽  
Salman Umar
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Scanning Electron Microscopy ◽  
Fourier Transform ◽  
Differential Thermal Analysis ◽  
Fourier Transform Infrared ◽  
X Ray Diffraction ◽  
Poloxamer 188 ◽  
X Ray ◽  
Scanning Electron

Sebuah penelitian tentang sistem dispersi padat dari asiklovir dengan poloxamer 188 telah dilakukan formulasi dengan pencampuran secara fisika dengan rasio 1 : 1, 1 : 3, 1 : 5 dan dispersi padat 1 : 1, 1 : 3, 1 : 5 dan penggilingan 1:1 sebagai pembanding. Dispersi padat dibuat menggunakan metode pencairan (fusi), yang digabung dengan poloxamer 188 pada hotplate kemudian asiklovir dimasukkan ke dalam hasil poloxamer 188 lalu di kocok hingga membentuk masa homogen. Semua formula yang terbentuk termasuk asiklovir poloxamer 188 murni dianalisis karakterisasinya dengan Differential Thermal Analysis (DTA), X-ray Diffraction, Scanning Electron Microscopy (SEM), dan Fourier Transform Infrared (FTIR), kemudian pengambilan dilakukan  (penentuan kadar) mengunakan spektrofotometer UV pada panjang gelombang 257,08 nm dan uji laju disolusi dengan aquadest bebas CO2 menggunakan metode dayung. Hasil pengambilan  (penentuan kadar) menunjukkan bahwa semua formula memenuhi persyaratan farmakope Amerika edisi 30 dan farmakope Indonesia edisi 4 yaitu 95-110%. Sedangkan hasil uji laju disolusi untuk campuran fisik 1: 1, dan dispersi padat 1: 1, dan penggilingan 1: 1 menunjukkan peningkatan yang nyata dibandingkan asiklovir murni. Hal ini juga dapat dilihat dari hasil perhitungan statistik  menggunakan analisis varian satu arah  SPSS 17.

scholarly journals The Potential for Natural Stones from Northeastern Brazil to Be Used in Civil Construction

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 440
Author(s):  
Fabiana Pereira da Costa ◽  
Jucielle Veras Fernandes ◽  
Luiz Ronaldo Lisboa de Melo ◽  
Alisson Mendes Rodrigues ◽  
Romualdo Rodrigues Menezes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Chemical Resistance ◽  
Mechanical Analysis ◽  
Northeastern Brazil ◽  
X Ray Diffraction ◽  
X Ray ◽  
Chemical Agents ◽  
Natural Stones

Natural stones (limestones, granites, and marble) from mines located in northeastern Brazil were investigated to discover their potential for use in civil construction. The natural stones were characterized by chemical analysis, X-ray diffraction, differential thermal analysis, and optical microscopy. The physical-mechanical properties (apparent density, porosity, water absorption, compressive and flexural strength, impact, and abrasion) and chemical resistance properties were also evaluated. The results of the physical-mechanical analysis indicated that the natural stones investigated have the potential to be used in different environments (interior, exterior), taking into account factors such as people’s circulation and exposure to chemical agents.

The Roman Ceramics of Salobrena (Granada-Spain) and their Raw Materials

1992 ◽  
Vol 267 ◽  
Author(s):  
Ana M De Andres ◽  
Isabel MuÑOZ
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Raw Materials ◽  
Third Century ◽  
Western Coast ◽  
X Ray Diffraction ◽  
X Ray ◽  
The Third ◽  
Good Number ◽  
Scanning Electron

ABSTRACTNineteen roman ceramic sherds found near Salobreña (Granada, Spain), in the western coast of the Mediterranean Sea, as well as different ceramic clays from the surroundingsare studied. Both clays and ceramic sherds are characterizad by X-ray diffraction and spectrometry, differential thermal analysis, and scanning electron and optical microscopies. A good number of the ceramic pieces, among which some “Terrae Sigillatae”, have a composition similar to that of the local clays and, thus, have been probably manufactured at Salobreña. Only a few of them have a foreign origin. For most of them, the firing temperature was about 800-850 °C, although some have been produced at 900-1000 °C, and some others at 1000-1100 °C. It is concluded that Salobreña appearsto have been an important settlement just in the third century of the Christian era.

The Optical Performance of Holmium Oxide Doped Tellurite Glass for Potential Optical Fiber

2021 ◽  
Vol 317 ◽  
pp. 95-99
Author(s):  
Muhammad Noorazlan Abd Azis ◽  
Halimah Mohamed Kamari ◽  
Suriani Abu Bakar ◽  
Azlina Yahya ◽  
Umar Saad Aliyu
Keyword(s):  
Refractive Index ◽  
Band Gap ◽  
Tellurite Glass ◽  
Optical Band Gap ◽  
Band Gap Energy ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
Gap Energy ◽  
Xrd Method ◽  
Nonlinear Pattern

Borotellurite glass had been widely applied in the field of optical communications and devices. In this work, holmium oxides doped borotellurite glass had been successfully fabricated via conventional melt-quenched technique. The structural properties of holmium doped tellurite glass were found using x-ray diffraction (XRD) method. The nonexistence of sharp peaks in XRD pattern shows that the inclusion of holmium tellurite glass leads to the formation long range of disorderness. The optical properties of the glass system such as refractive index and optical band gap energy are investigated using UV-Vis spectrophotometer. The value of refractive index is found in nonlinear trend along with holmium oxides concentration. It is found that the refractive index is more than 2 at 0.01, 0.03 and 0.04 of holmium concentrations. The optical band gap energy was found in similar trend with refractive index which is in nonlinear pattern.

Structural-phase transition in (Cu2Te)2−x(ZnTe)x at high temperature

2021 ◽  
pp. 2150113
Author(s):  
H. B. Gasimov ◽  
R. M. Rzayev
Keyword(s):  
Phase Transition ◽  
Phase Transitions ◽  
High Temperature ◽  
Single Crystals ◽  
Structural Phase ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Range ◽  
Xrd Study ◽  
Xrd Method

Cu2Te single crystal was grown by the Bridgman method. X-ray diffraction (XRD) study of Cu2Te single crystals in the temperature range of 293–893 K was performed and possible phase transitions in the mentioned range of temperature have been investigated. (Cu2Te)[Formula: see text](ZnTe)[Formula: see text] single crystals also were grown with [Formula: see text], 0.05, 0.10 concentrations and structural properties of the obtained single crystals were investigated by the XRD method in the temperature range 293–893 K. Lattice parameters and possible phase transitions in the mention temperature range were determined for (Cu2Te)[Formula: see text](ZnTe)[Formula: see text] single crystals for [Formula: see text], 0.05, 0.10 concentrations.

scholarly journals Silica-Kaolin Mix Effect on Evaporative Pattern Castings Surface Roughness

2016 ◽  
Vol 16 (3) ◽  
pp. 83-88 ◽  
Author(s):  
B.V. Omidiji ◽  
R.H. Khan ◽  
M.S. Abolarin
Keyword(s):  
Thermal Analysis ◽  
Surface Roughness ◽  
Differential Thermal Analysis ◽  
Ratio Method ◽  
Gating System ◽  
X Ray Diffraction ◽  
Pouring Temperature ◽  
Material Loss ◽  
Refractory Coating ◽  
X Ray

Abstract The influence of the refractory coating which is a mixture of silica flour and kaolin on the surface roughness of the plate castings produced using evaporative patterns had been considered in this work. The kaolin was used as a binder and ratio method was employed to form basis for the factorial design of experiment which led to nine runs of experiments. Methyl alcohol at 99% concentration was used as the carrier for the transfer of the coating to the surface of the patterns. Pouring temperature was observed as a process parameter alongside the mix ratios of the coating. Attempts were made to characterize the refractory coating by using two methods; differential thermal analysis (DTA) and X-ray diffraction. Attempt was also made to characterize the casting material. Gating system design was done for the plate casting to determine the correct proportions of the gating parameters in order to construct the gating system properly to avoid turbulence during pouring of liquid metal. A digital profilometer was used to take the measurements of the surface roughness. It was observed that the mix ratio 90% silica flour-10% kaolin produced the lowest value of the surface roughness of the plate castings and had the lowest material loss in the DTA test. The pouring temperature of 650°C produced best casting.

scholarly journals SOLUBILITY OF GERMANIUM DISELENIDE IN THE Cu3AsSe4

2021 ◽  
Vol 0 (4) ◽  
pp. 67-70
Author(s):  
Z.T. Hasanova ◽  
Keyword(s):  
Thermal Analysis ◽  
Differential Thermal Analysis ◽  
Phase Equilibria ◽  
Solid Solutions ◽  
X Ray Diffraction ◽  
X Ray

Differential thermal analysis and powder X-ray diffraction methods were used for phase equilibria studying in the Cu3AsSe4-GeSe2 system. It was established that wide (up to 30 mol.%) solid solutions based on Cu3AsSe4 are formed. GeSe2-rich alloys consist of various heterogeneous mixtures, including phases outside the T–x plane of this section

scholarly journals Flexible ZnO photoelectrode for photo electrochemical energy conversion

2021 ◽  
Author(s):  
T. Shiyani ◽  
Indrani Banerjee ◽  
Santosh K. Mahapatra ◽  
Asim K Ray
Keyword(s):  
Band Gap ◽  
Diffraction Pattern ◽  
Absorption Spectra ◽  
Optical Band Gap ◽  
Solar Fuels ◽  
Photoelectrochemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
A Value ◽  
Pet Substrate

Abstract Photoelectrochemical properties have been investigated for flexible ZnO/ITO/PET photoelectrodes. ZnO was spin coated on ITO/PET substrate with thickness of about 310 nm. The high crystalline structure of ZnO was studied using x-ray diffraction pattern. A value of 3.4 eV has been estimated for optical band gap from its absorption spectra. The flexible ZnO photoelectrode was demonstrated to generate photoelectrochemical current. Values of 1.022 and 0.714 were found to be for photo switching and photoresponsivity, respectively. ZnO/ITO/PET can be used as a substrate for making flexible hybrid PEC devices to generate solar power and solar fuels.

Sign in / Sign up

Export Citation Format

Share Document