scholarly journals The Effect of Using Plastic Strips and Sheets on the Properties of Slurry Infiltrated Fiber Concrete

2021 ◽  
Vol 11 (6) ◽  
pp. 7800-7804
Author(s):  
A. M. Najeeb ◽  
N. M. Fawzi
Keyword(s):  
Flexural Strength ◽  
Steel Fibers ◽  
Unique Type ◽  
High Fiber ◽  
Water To Cement Ratio ◽  
Strength Tests ◽  
Fiber Concrete ◽  
Strong Material ◽  
Control Set ◽  
The Difference

Slurry Infiltrated Fiber Concrete (SIFCON) is a high-strong material that is regarded as a unique type of high fiber content concrete. This paper aims to study the influence of the use of plastic strips and plastic sheets in the SIFCON slurry. Three sets (normal SIFCON as control, SIFCON with plastic strips, and SIFCON with plastic sheet), in a 1:1.08 cement-sand ratio by weight has been used with water to cement ratio (w/c) by weight equal to 0.3, and superplasticizer equal to 1% by weight. In addition, 6% by volume crimped steel fibers with an aspect ratio of 60 were applied and 1.34% by volume plastic was used, in strips of 5×1cm for both prism and cube samples and in sheets of 25×5cm and 7×7cm for prism and cube samples respectively. The compressive and flexural strength tests studies were conducted on typical cubes of 10×10×10cm and prisms of 40×7×7cm respectively to find out the way the plastic affects the SIFCON properties. The results indicate that the models with plastic sheets placed in SIFCON slurry give the highest compressive and flexural strength whereas the models with plastic strips gave the lowest. The difference percentages in compressive and flexural strength were -27.3, 8, -3.8 and 66.6% for all sets respectively when compared to the control set (using no plastic).

Evaluation of Fundamental UHPC Properties According to the Shape of Steel Fiber

2010 ◽  
Vol 452-453 ◽  
pp. 717-720 ◽  
Author(s):  
Gum Sung Ryu ◽  
Su Tae Kang ◽  
Jung Jun Park ◽  
Kyung Taek Koh ◽  
Sung Wook Kim
Keyword(s):  
Aspect Ratio ◽  
Flexural Strength ◽  
High Performance ◽  
High Performance Concrete ◽  
Steel Fibers ◽  
Flexural Behavior ◽  
Ultra High Performance Concrete ◽  
Aspect Ratios ◽  
Strength Tests ◽  
Shaped Fibers

This paper intends to examine the effects if the length and shape of steel fibers on the mechanical characteristics of ultra-high performance concrete (UHPC). Accordingly, the length (l) of the steel fibers with diameter (d) of 0.2 mm is varied as 13 mm, 16.3 mm and 19.5 mm and their corresponding aspect ratios (l/d) are 65, 82 and 98. Straight and wave-shaped fibers are adopted to manufacture UHPC. Thereafter, the effects of the aspect ratio and characteristics of the wave-shape of the steel fibers on the strength characteristics of UHPC are examined through compressive and flexural strength tests. The results showed small differences in the workability and compressive behavior but revealed that changing the length of the fibers and increasing the aspect ratio are improving the flexural behavior of UHPC. Specifically, the flexural strength was enhanced by 25% and the flexural toughness by 30%. Compared to rectilinear fibers, the adoption of wave-shaped fibers is seen to degrade the flexural behavior regardless of the aspect ratio. Consequently, using straight steel fibers and adopting larger aspect ratio seems advisable to improve the toughness of UHPC.

scholarly journals Karakteristik Mortar Polimer Epoxy Resin Dengan Fiberglass

CANTILEVER ◽  
2021 ◽  
Vol 10 (2) ◽  
pp. 73-78
Author(s):  
Bambang Utomo ◽  
Siti Aisyah Nurjannah ◽  
Saloma
Keyword(s):  
Compressive Strength ◽  
Electron Microscope ◽  
Flexural Strength ◽  
Specific Gravity ◽  
Epoxy Resin ◽  
Cement Material ◽  
Strong Material ◽  
The Difference ◽  
Short Time ◽  
Scanning Electron

Nowadays, the developments of technology in construction are progressing very rapidly, one of which is mortar without using cement material. This encourages the development of concrete and mortar technology so that it can be widely used to repair structural or non-structural damages. In these conditions, a binder is needed in the form of an epoxy resin polymer with added fiberglass to get a strong material result in a short time. A mixture of 75% sand and 25% epoxy resin from the volume of the test object resulted a mortar compressive strength of 35.50 MPa with a specific gravity of 1.505 kg/m3. The results showed that the variation of the compressive strength of the epoxy resin mortar without fiber was higher than the variation with fiberglass. This was due to the addition of fiberglass reducing the composition of the percentage of epoxy resin which results in reduced bonding power in the mixture. The flexural strength of a mortar with variations using fiberglass was 8 MPa and showed the best performance, although the difference was not too far from the variation without fiberglass. This was because the addition of fiberglass can reduce cracks, so that the fibers can bind well. The tests had been carried out including tests of the compressive strength, flexural strength, and Scanning Electron Microscope (SEM).

Flexural Performance of Reinforced Concrete Built-up Beams with SIFCON

2020 ◽  
Vol 38 (5A) ◽  
pp. 669-680
Author(s):  
Ghazwan K. Mohammed ◽  
Kaiss F. Sarsam ◽  
Ikbal N. Gorgis
Keyword(s):  
Reinforced Concrete ◽  
Ultimate Load ◽  
Concrete Beams ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Conventional Concrete ◽  
Flexural Performance ◽  
Load Carrying ◽  
Fiber Concrete

The study deals with the effect of using Slurry infiltrated fiber concrete (SIFCON) with the reinforced concrete beams to explore its enhancement to the flexural capacity. The experimental work consists of the casting of six beams, two beams were fully cast by conventional concrete (CC) and SIFCON, as references. While the remaining was made by contributing a layer of SIFCON diverse in-depth and position, towards complete the overall depths of the built-up beam with conventional concrete CC. Also, an investigation was done through the control specimens testing about the mechanical properties of SIFCON. The results showed a stiffer behavior with a significant increase in load-carrying capacity when SIFCON used in tension zones. Otherwise high ductility and energy dissipation appeared when SIFCON placed in compression zones with a slight increment in ultimate load. The high volumetric ratio of steel fibers enabled SIFCON to magnificent tensile properties.

Test Comparison Research Mechanics Performance between Sisal Fiber Concrete and Rubber Powder Concrete

2011 ◽  
Vol 243-249 ◽  
pp. 494-498
Author(s):  
Hui Ming Bao
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Sisal Fiber ◽  
Environment Friendly ◽  
Rubber Powder ◽  
Comparison Research ◽  
Mechanics Performance ◽  
Fiber Concrete ◽  
Sisal Fibers

By means of the tests on the mechanics performance of the reinforcing concrete mixed with sisal fibers or rubber powder of certain content are investigated. The compressive strength, tensile strength and flexural strength, etc. are compared. The test indicates that when the test condition is same, the compressive strength, tensile strength and flexural strength of the sisal fibers concrete are better than those of the rubber powder’s. The sisal fiber concrete is environment friendly than the rubber powder concrete. And it has widely value of spread and utilization.

scholarly journals Effect of microwave disinfection on physical and mechanical properties of acrylic resins

2008 ◽  
Vol 19 (4) ◽  
pp. 348-353 ◽  
Author(s):  
Rafael Leonardo Xediek Consant ◽  
Erica Brenoe Vieira ◽  
Marcelo Ferraz Mesquita ◽  
Wilson Batista Mendes ◽  
João Neudenir Arioli-Filho
Keyword(s):  
Flexural Strength ◽  
Room Temperature ◽  
Physical And Mechanical Properties ◽  
Hardness Test ◽  
Knoop Hardness ◽  
Microwave Energy ◽  
Bending Test ◽  
Acrylic Resins ◽  
Strength Tests ◽  
The Impact

This study evaluated the effect of microwave energy on the hardness, impact strength and flexural strength of the Clássico, Onda-Cryl and QC-20 acrylic resins. Aluminum die were embedded in metallic or plastic flasks with type III dental stone, in accordance with the traditional packing technique. A mixing powder/liquid ratio was used according to the manufacturer's instructions. After polymerization in water batch at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling at room temperature, and submitted to finishing. Specimens non-disinfected and disinfected by microwave irradiation were submitted to hardness, impact and flexural strength tests. Each specimen was immersed in distilled water and disinfected in a microwave oven calibrated to 650 W for 3 min. Knoop hardness test was performed with 25 g load for 10 s, impact test was carried out using the Charpy system with 40 kpcm, and 3-point bending test with a crosshead speed of 0.5 mm/min until fracture. Data were submitted to statistical analysis by ANOVA and Tukey's test (?=0.05). Disinfection by microwave energy decreased the hardness of Clássico and Onda-Cryl acrylic resins, but no effect was observed on the impact and flexural strength of all tested resins.

scholarly journals Influence of Hybrid Fibers on Toughness Behavior of High Strength Flowing Concrete

2011 ◽  
Vol 57 (3) ◽  
pp. 249-260 ◽  
Author(s):  
Eethar Thanon Dawood ◽  
Mahyuddin Ramli
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Modulus Of Elasticity ◽  
Hybrid Composite ◽  
High Strength ◽  
Steel Fibers ◽  
Hybrid Fibers ◽  
Static Modulus ◽  
Static Modulus Of Elasticity ◽  
Strength And Toughness

Abstract This study investigates the use of steel fibers and hybrid composite with a total fibers content of 2% on the high strength flowing concrete and determines the density, compressive strength, static modulus of elasticity, flexural strength and toughness indices for the mixes. The results show that the inclusion of more than 0.5% of palm fibers in hybrid fibers mixes reduces the compressive strength. The hybrid fibers can be considered as a promising concept and the replacement of a portion of steel fibers with palm fibers can significantly reduce the density, enhance the flexural strength and toughness. The results also indicates that the use of hybrid fibers (1.5 steel fibers + 0.5% palm fibers) in specimens increases significantly the toughness indices and thus the use of hybrid fibers combinations in reinforced concrete would enhance their flexural toughness & rigidity and enhance their overall performances

scholarly journals Examining Polyethylene Terephthalate (PET) as Artificial Coarse Aggregates in Concrete

2020 ◽  
Vol 6 (12) ◽  
pp. 2416-2424
Author(s):  
Erniati Bachtiar ◽  
Mustaan Mustaan ◽  
Faris Jumawan ◽  
Meldawati Artayani ◽  
Tahang Tahang ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Flexural Strength ◽  
Polyethylene Terephthalate ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
Coarse Aggregates ◽  
Volume Weight ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Recycled Polyethylene

This study aims to examine the effect of recycled Polyethylene Terephthalate (PET) artificial aggregate as a substitute for coarse aggregate on the compressive strength and flexural strength, and the volume weight of the concrete. PET plastic waste is recycled by heating to a boiling point of approximately 300°C. There are five variations of concrete mixtures, defined the percentage of PET artificial aggregate to the total coarse aggregate, by 0, 25, 50, 75 and 100%. Tests carried out on fresh concrete mixtures are slump, bleeding, and segregation tests. Compressive and flexural strength tests proceeded based on ASTM 39/C39M-99 and ASTM C293-79 standards at the age of 28 days. The results showed that the use of PET artificial aggregate could improve the workability of the concrete mixture. The effect of PET artificial aggregate as a substitute for coarse aggregate on the compressive and flexural strength of concrete is considered very significant. The higher the percentage of PET plastic artificial aggregate, the lower the compressive and flexural strength, and the volume weight, of the concrete. Substitution of 25, 50, 75 and 100% of PET artificial aggregate gave decreases in compressive strength of 30.06, 32.39, 41.73 and 44.06% of the compressive strength of the standard concrete (18.20 MPa), respectively. The reductions in flexural strength were by respectively 19.03, 54.50, 53.95 and 61.00% of the standard concrete's flexural strength (3.59 MPa). The reductions in volume weight of concrete were by respectively 8.45, 17.71, 25.07 and 34.60% of the weight of the standard concrete volume of 2335.4 kg/m3 Doi: 10.28991/cej-2020-03091626 Full Text: PDF

scholarly journals ANALYSIS OF PROPERTIES OF CONCRETE USING STEEL FIBERS AS FIBER REINFORCEMENT ADMIXTURE

2017 ◽  
Vol 5 (4RASM) ◽  
pp. 59-62
Author(s):  
Vishal Gadgihalli ◽  
Meena ◽  
Sindu ◽  
Raghavendra Prasad Dinakar
Keyword(s):  
Reinforced Concrete ◽  
Flexural Strength ◽  
Steel Fibre ◽  
Fiber Reinforcement ◽  
Paper Analysis ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Different Types ◽  
Discrete Uniform

Fiber reinforced concrete is composite material consisting of mixtures of cement, mortar or concrete, discontinuous discrete uniform dispersed suitable fibers. Fiber reinforced concrete are of different types and properties. In this paper analysis of properties of concrete using steel fibre as fiber reinforcement admixture is studied and verified the strength of concrete to normal plane concrete with absence of admixtures. Using steel fibers as fiber reinforcement admixture increases bond strength by enhancing surface tension as steel is better in taking flexural strength this gives better results, hence we can use this steel fiber reinforcement to concrete where the compressive and flexural strength place a crucial role in construction and maintenance.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

scholarly journals Experimental study on high temperature mechanical properties of aluminate cement mortar mixed with fiber

2021 ◽  
Vol 25 (6 Part B) ◽  
pp. 4441-4448
Author(s):  
Ping Xu ◽  
Dong Han ◽  
Jian-Xin Yu ◽  
Yu-Hao Cui ◽  
Min-Xia Zhang
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Volume Fraction ◽  
Cement Mortar ◽  
Steel Fibers ◽  
Basalt Fibers ◽  
High Temperature Mechanical Properties ◽  
Micro Structures ◽  
Aluminate Cement

The aim of the present paper is to study the mechanical properties of aluminate cement mortar mixed with different chopped fibers under high temperature. The specimens with a size of 40 mm ? 40 mm ? 160 mm is treated at various tempera?tures of 25?C, 200?C, 400?C, 600?C, and 800?C. The compressive and flexural strength of the aluminate cement mortar and its micro-structures are tested. The results show that the chopped steel fibers and basalt fibers are effective in improv?ing the high temperature mechanical properties of aluminate cement mortar. When the volume fraction of chopped steel fibers is 2%, the compressive strength and flexural strength of the test block treated at the temperature of 800?C increase by 18.3% and 128.6%, respectively.

Sign in / Sign up

Export Citation Format

Share Document