Research on seismic performance of traditional Chinese hall-style timber buildings in the Song and Yuan dynasties (960–1368 AD): a case study of the main hall of Baoguo Temple

The hall-style timber frame built in the Song and Yuan dynasties (960–1368 AD) is one of the most important structural prototypes of the traditional timber architecture in East Asia. The current research, through a typical case of the main hall of Baoguo Temple in Ningbo, China, aims to present an accurate and effective seismic performance evaluation method applicable to hall-style timber structures without time–cost expenditure. To obtain more realistic seismic response of hall-style timber frame, a simplified numerical model of the main hall of Baoguo Temple is established based on in situ measurements and low-cycle reversed loading tests results of mortise–tenon joints, moreover, nonlinear static pushover analysis has been performed to quantify the seismic performance levels under five loading conditions. The generalized force–deformation relationship of the timber plastic hinges is modified regarding to the moment–rotation curves of four special mortise–tenon joints. The seismic behaviour of global hall-style timber frame is evaluated through capacity spectrum method and verified by time history analysis, local failure mechanisms are evaluated by the occurrence sequence of plastic hinges. Finally, a performance-based assessment method adequate for the traditional hall-style timber architectures has been proposed with comparison to the current codes. The results have shown that the structural stiffness of the width-direction is less than that of the depth direction due to the asymmetrical configuration of the timber frame, and the building can maintain a stable state under large lateral displacement before collapsing. The inter-storey drift angles of the building under peak ground accelerations of 0.1 g, 0.2 g, and 0.3 g are less than the suggested ultimate values in the current local codes, however, the main hall represents to be more vulnerable to damage when suffer seismic action along the width-direction. This research can provide a reference for seismic performance evaluation and preventive conservation of ancient hall-style timber architectural heritage.

A revised method to calculate time-varying mesh stiffness of helical gear

Time-varying mesh stiffness (TVMS) of gear plays vital role in analysing dynamic characteristic of gear transmission. So accurately evaluating the TVMS is important and essential. In this paper, a revised method to calculate the TVMS of helical gear is proposed. Based on slice method, the helical gear is sliced into pieces along the tooth width direction. The proposed method corrects the fillet foundation stiffness within multi-tooth in contact and considers the non-linearity and load-dependence of the Hertzian contact stiffness. The effect of the axial mesh force is considered. Finally, an equivalent helical gear model is established in ANSYS to study the mesh stiffness. The results show the proposed method has high effectiveness compared with FEM (finite element method).

Variation in Deformation Behaviors Along the Transverse Direction During the Warm Rolling of a 1480-mm-Wide AZ31B Plate

A decrease in the weight of aerospace vehicles, large ships, weapons, and high-speed trains will increase the demand for wide-width magnesium alloy plates and their composite parts to replace steel and plastic. An investigation was conducted to study the variation in deformation behaviors along the transverse direction during the warm rolling of a 1480-mm-wide AZ31B plate. A uniaxial thermal compression test with a 59 % reduction was performed at different positions on a 13.7-mm-thick rolled plate along the width direction at a temperature of 220 °C and 270 °C and strain rate of 15 s−1. At the same time, the 13.7-mm-thick plate was rolled in a single pass to 5.6 mm on a mill with a 1725-mm-wide roll to confirm the thermal deformation behavior and the dynamic recrystallization (DRX). The results show that the main texture type does not change and the grain size does not have a clear deflection when the magnesium alloy plate reaches a certain value under rolling accumulative reduction. The grain size of a 13.7-mm-thick plate increases with a decrease in the distance to the center layer in the thickness direction. In the width direction, the edge (R6) first decreases and then increases toward the symmetric plane (R1). The critical stress required for dynamic recrystallization in the transition zone R3 of the rolled plate width is minimum, and the average grain size is minimum owing to the relatively complete recrystallization.

The Dissimilar Self-Alignment Characteristics of Smaller Passive Components in the Length and Width Directions

Motivation: As passive components’ size gets smaller, quality rejects due to overhang and misalignment after the reflow appear more frequently. This situation is partly because the pass-fail criterion is set based on the offset concerning the component dimensions. Therefore, understanding the self-alignment characteristics of electronic components becomes very critical for surface-mount assembly yield. This research investigates the dissimilarity of self-alignment in the length and width directions. Approach: To avoid the argument of sample to sample variations, data are collected from 81 printed circuit boards (PCB) and 182,250 assembled components. Within a PCB, 25 different solder paste printing offset locations and 81 component placement offset settings are implemented. Component-placement positions before and after the reflow are monitored. The results are compared to identify different component sizes’ self-alignment characteristics in the length and width directions. Key findings: The misalignment of smaller passive components, e.g., R0402M(0.40 mm × 0.20 mm), is worse than the larger component under the identical solder paste printing and component placement conditions. Furthermore, the self-alignment characteristic in the length direction of these passive components, e.g., R0402M, to R1005M (1.00 mm × 0.50 mm) is superior to that of width direction. The observations are not consistent with the results found in earlier research that reported on larger components, e.g., C0402M(0.40 mm × 0.20 mm), to C3216M(3.20 mm × 1.50 mm).

Percolation networks inside 3D model of the mineralized collagen fibril

Bone is a hierarchical biological material, characterized at the nanoscale by a recurring structure mainly composed of apatite mineral and collagen, i.e. the mineralized collagen fibril (MCF). Although the architecture of the MCF was extensively investigated by experimental and computational studies, it still represents a topic of debate. In this work, we developed a 3D continuum model of the mineral phase in the framework of percolation theory, that describes the transition from isolated to spanning cluster of connected platelets. Using Monte Carlo technique, we computed overall 120 × 106 iterations and investigated the formation of spanning networks of apatite minerals. We computed the percolation probability for different mineral volume fractions characteristic of human bone tissue. The findings highlight that the percolation threshold occurs at lower volume fractions for spanning clusters in the width direction with respect to the critical mineral volume fractions that characterize the percolation transition in the thickness and length directions. The formation of spanning clusters of minerals represents a condition of instability for the MCF, as it could be the onset of a high susceptibility to fracture. The 3D computational model developed in this study provides new, complementary insights to the experimental investigations concerning human MCF.

A Top Side-Pouring Twin-Roll Caster for 3.0 Wt.% Si Steel

Three-dimensional finite element modeling of twin-roll strip casting (TRC) and the top side-pouring twin-roll casting (TSTRC) were carried out to predict the temperature, flow, and turbulence kinetic energy of the two processes. The cellular automaton–finite element (CA-FE) model was established to predict the solidification structure of the two processes. By comparing the two processes, it was found that the temperature field distribution in the micro-melt pool during the TSTRC process was uniform. The temperature distribution in the width direction was also more uniform, and the stirring in the micro melt-pool was intense. An equiaxed crystal structure uniformly distributed in the width direction was obtained, and a thin strip of good quality was obtained. Not only the near-final forming of the thin strip was realized, but also the near-final forming of the solidified structure was realized. By comparing the experimental process of TSTRC with the simulation, it was found that the simulation and experimental results were in good agreement, which verified the feasibility and accuracy of the simulation.

Influence of differential reduction rate in adjacent roll reduction zone on internal cracks of high carbon bloom induced by mechanical soft reduction

To comprehensively investigate and alleviate internal cracks in high carbon bloom induced by mechanical soft reduction (MSR), a 3D thermal-mechanical coupled model, containing two adjacent pairs of reduction rolls, was developed to investigate the influence of differential reduction rate on evolution of stress concentration and displacement in as-cast bloom. In order to effectively provide theoretical basis for actual production, the reduction rate was calculated according to the appropriate reduction amount of each pair of reduction rolls, which can be adopted in the MSR to determinate the appropriate roll reduction amount in adjacent roll reduction zone. With the differential reduction rate of MSR increasing from −2.67 mm/m to 5.33 mm/m, the maximum equivalent stress of cracking area in as-cast bloom significantly decreased under first roll reduction position, the maximal displacement along the bloom width direction is significantly decreased with increasing of the differential reduction rate of MSR under end roll reduction position. According to the results of industrial experiment, the internal cracks were effectively alleviated and center shrinkage cavities were nearly eliminated by optimum designed experiments.

Injection-rolling nozzle in an imprint system with continuous injection direct rolling for ultra-thin microstructure guide light plate

A novel Injection-rolling Nozzle (IRN) in an imprint system with continuous injection direct rolling (CIDR) for ultra-thin microstructure polymer guide light plates was developed to achieve uniform flow velocity and temperature at the width direction of the cavity exit. A novel IRN cavity was designed. There are eight of feature parameters of cavity were optimized by orthogonal experiments and numerical simulation. Results show that the flow velocity at the width direction of the IRN outlet can reach uniformity, which is far better than that of traditional cavity. The smallest flow velocity difference and temperature difference was 0.6 mm/s and 0.24 K, respectively. The superior performance of the IRN was verified through a CIDR experiment. Several 0.35-mm thick, 340-mm wide, and 10-m long microstructural Polymethyl Methacrylate (PMMA) guide light plates were manufactured. The average filling rates of the microgrooves with the aspect ratio 1:3 reached above 93%. The average light transmittance is 88%.

Bending Strength of Magnesium Oxide Board

Magnesium Oxide (MgO) board has been widely used in prefabricated lightweight steelframe wall systems and as the floor board covering component. It is a non-insulating sheathingboard product which consists of sustainable materials with the characteristics of fire resistance,weather-ability, strength, resistance to mold and mildew. Although MgO board has recentlyworldwide used in façade construction but the research data related to the laboratory work such asthe bending strength is still limited. The previous studies on the bending strength of MgO board arebased on various standards such as ASTM, JC688 and British Standard subjected to the productscharacteristics and patterns. Therefore, the bending strength values obtained were inconsistent andnot convincing. Thus, this paper aims to examine the bending strength of MgO board with threedifference thicknesses (6mm, 9 mm and 12 mm) based on BS EN 310:1993 subjected to threepoints bending test. The failure modes during three points bending test was observed and theexperimental results obtained were compared with the theoretical values and others relevantstandards. A total of thirty six specimens with twelve specimens for each thickness in two groupdirections namely longitudinal (length) and transverse (width) direction were tested. The specimenswere prepared based on BS EN 326-1:1994 and BS EN 325:2012. The maximum flexure load of thespecimens was recorded and arithmetic mean bending strength for each thickness was presented.The experimental results showed the tested MgO board was not achieved minimum bendingstrength for load bearing used. It is recommended to be used in non-load bearing façade claddingconstruction.

Design of a Kirigami Structure with a Large Uniform Deformation Region

We designed a kirigami structure with a particular shape at both ends to provide a large uniform deformation region when stretched. When a kirigami structure is stretched, non-deformation regions, where the regions’ cuts do not open, and non-uniform deformation regions, where the regions’ cuts are not uniformly deformed, are produced. The extent of the non-deformation and non-uniform deformation regions increases in proportion to the number of cut cycles in the width direction nw this reduces the percentage of the uniform deformation region. We propose a method that increases the uniform deformation region in a kirigami structure by deforming the shape of the ends from a rectangle to a trapezoid when stretched. The proposed kirigami structure has separation lines at both ends that separate cuts in the width direction, and the position of contacts at both ends are moved to the center. The proposed kirigami structure has a large uniform deformation region, even when nw is large, as evidenced by calculating the area of open cuts under stretching. The product of our study realizes a stretchable electro device with a large area, which maintains the position of evenly mounted functional elements when stretched.