The development characteristics of the discontinuous leader under the positive switching impulse with low rate of voltage rising

2018 ◽  
Vol 83 (2) ◽  
pp. 20802 ◽  
Author(s):  
Yaoheng Xie ◽  
Yue Yishi ◽  
Huisheng Ye ◽  
Liu Yun ◽  
Yongheng Zhong ◽  
...  
Keyword(s):  
High Speed ◽  
Large Scale ◽  
Unit Length ◽  
Leader Development ◽  
Air Gap ◽  
Discharge Process ◽  
Temperature Changes ◽  
Channel Temperature ◽  
Impulse Voltage ◽  
Low Rate

Discontinuous leader development is the most important discharge process under the application of the switching impulse voltage with the low rate of voltage rising, which is of great significance to study the external insulation characteristics of ultra-high voltage (UHV) large scale air gap. Based on the CMOS high-speed camera, a discharge test with different operating impulse voltage is carried out by constructing a comprehensive observation platform of rod-plate air gap discharge, and a clear discontinuous leader development process picture is captured. Moreover, the leader current, injection charge and leader channel unit length charge, and their characteristics of the change trend are also obtained. Further analysis based on the experimental results shows that the discontinuous leader development under the action of the impulse voltage with low rate of voltage rising has two different laws. Finally, this paper uses the thermodynamic equation, combined with the test results, the channel temperature changes in the discontinuous leader development stagnation stage were calculated. The results show that the leader channel temperature is still greater than 1500 K in the hundreds of microsecond time scales in the leader stagnation stage, and the subsequent leader can continue to develop on the original leader channel.

Evaluation of Windage Losses for High-Speed Disc Machinery

1992 ◽  
Vol 206 (3) ◽  
pp. 149-157 ◽  
Author(s):  
M R Etemad ◽  
K Pullen ◽  
C B Besant ◽  
N Baines
Keyword(s):  
Mass Flow ◽  
High Speed ◽  
Air Gap ◽  
Drag Torque ◽  
Torque Measurement ◽  
Air Mass ◽  
Temperature Changes ◽  
Insignificant Effect ◽  
Air Jets ◽  
Experimental Apparatus

Design and development of experimental apparatus is detailed for stator drag torque measurement as well as a method to evaluate rotor windage losses directly from air mass flow and temperature changes. Effects of air jets at the rotor rim were also investigated. Results are presented for air windage losses associated with ultra-high-speed machinery. These show that within the range investigated the air gap length between the rotor and the stator has an insignificant effect on windage losses. The lowest windage losses were encountered when air was forced through the rotor/stator gap from the direction of rim to bore.

scholarly journals Continuous and Discontinuous Streamer Leader Propagation Phenomena under Slow Front Impulse Voltages in a 10-meter Rod-Plane Air Gap

Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2636 ◽  
Author(s):  
Wahab Ali Shah ◽  
Hengxin He ◽  
Junjia He ◽  
Yongchao Yang
Keyword(s):  
Quantitative Research ◽  
High Speed ◽  
Large Scale ◽  
Physical Phenomenon ◽  
Ccd Camera ◽  
Leader Development ◽  
Charge Coupled Device ◽  
The Comparative Study ◽  
Leader Process ◽  
Observation Results

Investigation of positive streamer-leader propagation under slow front impulse voltages can play an important role in the quantitative research of positive upward lightning. In this work, we performed a large-scale investigation into leader development in a 10-m rod–plane gap under a long front positive impulse. To describe the leader propagation under slow front impulse voltages, we recorded the leader propagation with a high-speed charge coupled device (CCD) camera. It is important to figure out this phenomenon to deepen our understanding of leader discharge. The observation results showed that the leader mechanism is a very complex physical phenomenon; it could be categorized into two types of leader process, namely, continuous and the discontinuous leader streamer-leader propagation. Furthermore, we studied the continuous leader development parameters, including two-dimensional (2-D) leader length, injected charge, and final jump stage, as well as leader velocity for rod–plane configuration. We observed that the discontinuous leader makes an important contribution to the appearance of channel re-illuminations of the positive leader. To clarify the above doubts under long front cases, we carried out extensive experiments in this study. The comparative study shows better results in terms of standard switch impulse and long front positive impulse. Finally, the results are presented with a view toward improving our understanding of propagation mechanisms related to restrike phenomena, which are rarely reported.

Formation of Standing Waves in Radial Tires

1984 ◽  
Vol 12 (1) ◽  
pp. 44-63 ◽  
Author(s):  
Y. D. Kwon ◽  
D. C. Prevorsek
Keyword(s):  
High Speed ◽  
Critical Speed ◽  
Unit Length ◽  
Standing Waves ◽  
Rolling Resistance ◽  
Damping Coefficient ◽  
Circular Membrane ◽  
Critical Speeds ◽  
Steel Cord ◽  
The Individual

Abstract Radial tires for automobiles were subjected to high speed rolling under load on a testing wheel to determine the critical speeds at which standing waves started to form. Tires of different makes had significantly different critical speeds. The damping coefficient and mass per unit length of the tire wall were measured and a correlation between these properties and the observed critical speed of standing wave formation was sought through use of a circular membrane model. As expected from the model, desirably high critical speed calls for a high damping coefficient and a low mass per unit length of the tire wall. The damping coefficient is particularly important. Surprisingly, those tire walls that were reinforced with steel cord had higher damping coefficients than did those reinforced with polymeric cord. Although the individual steel filaments are elastic, the interfilament friction is higher in the steel cords than in the polymeric cords. A steel-reinforced tire wall also has a higher density per unit length. The damping coefficient is directly related to the mechanical loss in cyclic deformation and, hence, to the rolling resistance of a tire. The study shows that, in principle, it is more difficult to design a tire that is both fuel-efficient and free from standing waves when steel cord is used than when polymeric cords are used.

Do elite soccer players cover longer distance when losing? Differences between attackers and defenders

2020 ◽  
pp. 174795412098227
Author(s):  
Carlos Lago-Peñas ◽  
Anton Kalén ◽  
Miguel Lorenzo-Martinez ◽  
Roberto López-Del Campo ◽  
Ricardo Resta ◽  
...  
Keyword(s):  
New York ◽  
High Speed ◽  
Large Scale ◽  
Tracking System ◽  
Soccer Players ◽  
Running Performance ◽  
Situational Variables ◽  
Total Distance ◽  
Professional Soccer ◽  
Score Line

This study aimed to evaluate the effects playing position, match location (home or away), quality of opposition (strong or weak), effective playing time (total time minus stoppages), and score-line on physical match performance in professional soccer players using a large-scale analysis. A total of 10,739 individual match observations of outfield players competing in the Spanish La Liga during the 2018–2019 season were recorded using a computerized tracking system (TRACAB, Chyronhego, New York, USA). The players were classified into five positions (central defenders, players = 94; external defenders, players = 82; central midfielders, players = 101; external midfielders, players = 72; and forwards, players = 67) and the following match running performance categories were considered: total distance covered, low-speed running (LSR) distance (0–14 km · h−1), medium-speed running (MSR) distance (14–21 km · h−1), high-speed running (HSR) distance (>21 km · h−1), very HSR (VHSR) distance (21–24 km · h−1), sprint distance (>24 km · h−1) Overall, match running performance was highly dependent on situational variables, especially the score-line condition (winning, drawing, losing). Moreover, the score-line affected players running performance differently depending on their playing position. Losing status increased the total distance and the distance covered at MSR, HSR, VHSR and Sprint by defenders, while attacking players showed the opposite trend. These findings may help coaches and managers to better understand the effects of situational variables on physical performance in La Liga and could be used to develop a model for predicting the physical activity profile in competition.

scholarly journals Research on the Ignition Height and Reaction Flame Temperature of PTFE/Al/Si/CuO with Different Mass Ratios of PTFE/Si

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3464
Author(s):  
Xuan Zou ◽  
Jingyuan Zhou ◽  
Xianwen Ran ◽  
Yiting Wu ◽  
Ping Liu ◽  
...  
Keyword(s):  
Energy Release ◽  
High Speed ◽  
Flame Temperature ◽  
Sintering Process ◽  
Release Process ◽  
Reactive Material ◽  
Temperature Changes ◽  
Release Capacity ◽  
Mass Ratios ◽  
The Relationship

Recent studies have shown that the energy release capacity of Polytetrafluoroethylene (PTFE)/Al with Si, and CuO, respectively, is higher than that of PTFE/Al. PTFE/Al/Si/CuO reactive materials with four proportions of PTFE/Si were designed by the molding–sintering process to study the influence of different PTFE/Si mass ratios on energy release. A drop hammer was selected for igniting the specimens, and the high-speed camera and spectrometer systems were used to record the energy release process and the flame spectrum, respectively. The ignition height of the reactive material was obtained by fitting the relationship between the flame duration and the drop height. It was found that the ignition height of PTFE/Al/Si/CuO containing 20% PTFE/Si is 48.27 cm, which is the lowest compared to the ignition height of other Si/PTFE ratios of PTFE/Al/Si/CuO; the flame temperature was calculated from the flame spectrum. It was found that flame temperature changes little for the same reactive material at different drop heights. Compared with the flame temperature of PTFE/Al/Si/CuO with four mass ratios, it was found that the flame temperature of PTFE/Al/Si/CuO with 20% PTFE/Si is the highest, which is 2589 K. The results show that PTFE/Al/Si/CuO containing 20% PTFE/Si is easier to be ignited and has a stronger temperature destruction effect.

scholarly journals 1.5 °C degrowth scenarios suggest the need for new mitigation pathways

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Lorenz T. Keyßer ◽  
Manfred Lenzen
Keyword(s):  
Technological Change ◽  
High Speed ◽  
Large Scale ◽  
High Energy ◽  
Climate Mitigation ◽  
Intergovernmental Panel ◽  
Economic Output ◽  
Integrated Assessment Modelling ◽  
Negative Emissions ◽  
Energy Emissions

Abstract1.5  °C scenarios reported by the Intergovernmental Panel on Climate Change (IPCC) rely on combinations of controversial negative emissions and unprecedented technological change, while assuming continued growth in gross domestic product (GDP). Thus far, the integrated assessment modelling community and the IPCC have neglected to consider degrowth scenarios, where economic output declines due to stringent climate mitigation. Hence, their potential to avoid reliance on negative emissions and speculative rates of technological change remains unexplored. As a first step to address this gap, this paper compares 1.5  °C degrowth scenarios with IPCC archetype scenarios, using a simplified quantitative representation of the fuel-energy-emissions nexus. Here we find that the degrowth scenarios minimize many key risks for feasibility and sustainability compared to technology-driven pathways, such as the reliance on high energy-GDP decoupling, large-scale carbon dioxide removal and large-scale and high-speed renewable energy transformation. However, substantial challenges remain regarding political feasibility. Nevertheless, degrowth pathways should be thoroughly considered.

scholarly journals Three-Axis Inductive Displacement Sensor Using Phase-Sensitive Digital Signal Processing for Industrial Magnetic Bearing Applications

Actuators ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 115
Author(s):  
Teemu Sillanpää ◽  
Alexander Smirnov ◽  
Pekko Jaatinen ◽  
Jouni Vuojolainen ◽  
Niko Nevaranta ◽  
...  
Keyword(s):  
Signal Processing ◽  
Digital Signal Processing ◽  
Eddy Current ◽  
High Speed ◽  
Digital Signal ◽  
Magnetic Bearing ◽  
Air Gap ◽  
Sensor Design ◽  
Quadrature Demodulation ◽  
Displacement Sensors

Non-contact rotor position sensors are an essential part of control systems in magnetically suspended high-speed drives. In typical active magnetic bearing (AMB) levitated high-speed machine applications, the displacement of the rotor in the mechanical air gap is measured with commercially available eddy current-based displacement sensors. The aim of this paper is to propose a robust and compact three-dimensional position sensor that can measure the rotor displacement of an AMB system in both the radial and axial directions. The paper presents a sensor design utilizing only a single unified sensor stator and a single shared rotor mounted target piece surface to achieve the measurement of all three measurement axes. The sensor uses an inductive measuring principle to sense the air gap between the sensor stator and rotor piece, which makes it robust to surface variations of the sensing target. Combined with the sensor design, a state of the art fully digital signal processing chain utilizing synchronous in-phase and quadrature demodulation is presented. The feasibility of the proposed sensor design is verified in a closed-loop control application utilizing a 350-kW, 15,000-r/min high-speed industrial induction machine with magnetic bearing suspension. The inductive sensor provides an alternative solution to commercial eddy current displacement sensors. It meets the application requirements and has a robust construction utilizing conventional electrical steel lamination stacks and copper winding.

scholarly journals Prevention of Mountain Disasters and Maintenance of Residential Area through Real-Time Terrain Rendering

2021 ◽  
Vol 13 (5) ◽  
pp. 2950
Author(s):  
Su-Kyung Sung ◽  
Eun-Seok Lee ◽  
Byeong-Seok Shin
Keyword(s):  
Real Time ◽  
Graphics Processing Units ◽  
High Speed ◽  
Large Scale ◽  
Civil Engineering ◽  
Three Dimensional ◽  
Sampled Data ◽  
Residential Areas ◽  
Terrain Rendering ◽  
Mountain Disasters

Climate change increases the frequency of localized heavy rains and typhoons. As a result, mountain disasters, such as landslides and earthworks, continue to occur, causing damage to roads and residential areas downstream. Moreover, large-scale civil engineering works, including dam construction, cause rapid changes in the terrain, which harm the stability of residential areas. Disasters, such as landslides and earthenware, occur extensively, and there are limitations in the field of investigation; thus, there are many studies being conducted to model terrain geometrically and to observe changes in terrain according to external factors. However, conventional topography methods are expressed in a way that can only be interpreted by people with specialized knowledge. Therefore, there is a lack of consideration for three-dimensional visualization that helps non-experts understand. We need a way to express changes in terrain in real time and to make it intuitive for non-experts to understand. In conventional height-based terrain modeling and simulation, there is a problem in which some of the sampled data are irregularly distorted and do not show the exact terrain shape. The proposed method utilizes a hierarchical vertex cohesion map to correct inaccurately modeled terrain caused by uniform height sampling, and to compensate for geometric errors using Hausdorff distances, while not considering only the elevation difference of the terrain. The mesh reconstruction, which triangulates the three-vertex placed at each location and makes it the smallest unit of 3D model data, can be done at high speed on graphics processing units (GPUs). Our experiments confirm that it is possible to express changes in terrain accurately and quickly compared with existing methods. These functions can improve the sustainability of residential spaces by predicting the damage caused by mountainous disasters or civil engineering works around the city and make it easy for non-experts to understand.

scholarly journals Optimization of Air Gap Length and Capacitive Auxiliary Winding in Three-Phase Induction Motors Based on a Genetic Algorithm

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4407
Author(s):  
Mbika Muteba
Keyword(s):  
Genetic Algorithm ◽  
Design Process ◽  
Power Factor ◽  
High Speed ◽  
High Efficiency ◽  
Air Gap ◽  
Element Analysis ◽  
Three Phase ◽  
High Torque ◽  
Cage Induction Motor

There is a necessity to design a three-phase squirrel cage induction motor (SCIM) for high-speed applications with a larger air gap length in order to limit the distortion of air gap flux density, the thermal expansion of stator and rotor teeth, centrifugal forces, and the magnetic pull. To that effect, a larger air gap length lowers the power factor, efficiency, and torque density of a three-phase SCIM. This should inform motor design engineers to take special care during the design process of a three-phase SCIM by selecting an air gap length that will provide optimal performance. This paper presents an approach that would assist with the selection of an optimal air gap length (OAL) and optimal capacitive auxiliary stator winding (OCASW) configuration for a high torque per ampere (TPA) three-phase SCIM. A genetic algorithm (GA) assisted by finite element analysis (FEA) is used in the design process to determine the OAL and OCASW required to obtain a high torque per ampere without compromising the merit of achieving an excellent power factor and high efficiency for a three-phase SCIM. The performance of the optimized three-phase SCIM is compared to unoptimized machines. The results obtained from FEA are validated through experimental measurements. Owing to the penalty functions related to the value of objective and constraint functions introduced in the genetic algorithm model, both the FEA and experimental results provide evidence that an enhanced torque per ampere three-phase SCIM can be realized for a large OAL and OCASW with high efficiency and an excellent power factor in different working conditions.

Sign in / Sign up

Export Citation Format

Share Document