scholarly journals Thermal and Mechanical Characterization of Drawn Polypropylene Fibres

2021 ◽  
Vol 1199 (1) ◽  
pp. 012029
Author(s):  
V Krmelová ◽  
M Gavendová ◽  
J Krmela ◽  
P Skalková ◽  
E Loksik
Keyword(s):  
Mechanical Properties ◽  
Melt Spinning ◽  
Mechanical Characterization ◽  
Scanning Calorimetry ◽  
Polypropylene Fibres ◽  
Elongation At Break ◽  
Melting Temperatures ◽  
Cycle Loading ◽  
Melt Spinning Technique

Abstract The main objective of this work was to investigate the effect of different cellulose (CEL) content and the draw ratio on the thermal and mechanical properties of drawn polypropylene (PP) fibres. The modification of PP fibres during their production can helps to prepare PP fibres with improved properties, guarantees new opportunities for the expansion of an assortment of PP fibres in the clothing and domestic textile industries. The modified PP/CEL fibres were prepared from PP pellets and PP/cellulose masterbatch via the melt spinning technique at 260 °C followed by drawing for various draw ratios in the company Chemosvit, Fibrochem a. s. (Svit, Slovakia). Differential scanning calorimetry (DSC) was used to evaluate the thermal properties of PP fibres. The mechanical properties (tenacity and elongation at break and modulus of elasticity) and low cycle loading of modified PP fibres were also studied. The obtained experimental results of drawn PP/CEL fibres were compared with neat PP fibre prepared under the same technological conditions. Cellulose had a minimal effect on the melting temperatures of fibres and increased of the PP crystallization temperatures in comparison with the neat drawn PP fibre. The limited decrease of mechanical properties of prepared fibres were observed, but the decreases do not influence on the fibres commercial use.

Preparation and Characterization of TPU Toughened PLA Elastic Fibers

2014 ◽  
Vol 789 ◽  
pp. 117-121 ◽  
Author(s):  
Shi Chao Wang ◽  
Heng Xue Xiang ◽  
Xiao Shuang Wen ◽  
Zhe Zhou ◽  
Mei Fang Zhu
Keyword(s):  
Mechanical Properties ◽  
Cross Section ◽  
Melt Spinning ◽  
Thermoplastic Polyurethane ◽  
Strong Interactions ◽  
Poly Lactic Acid ◽  
Elastic Fibers ◽  
Elongation At Break ◽  
Thermal Stability Of

Poly (lactic acid) (PLA) elastic fibers were prepared by melt spinning using Thermoplastic polyurethane (TPU) as a toughing agent and PLA-g-MA(Maleic anhydride) as a compatibilizer. Thermal properties and thermal stability of PLA/TPU composites, as well as the cross section morphology and mechanical properties of fibers were studied in the present investigation. DSC results showed that PLA was immiscible with TPU. In addition, the incorporation of TPU decreased the melting enthalpy of PLA/TPU composites. TG results indicated that the initial degradation temperatures of composites were also decreased by the appearance of TPU, and it decreased by 9°Cwhen TPU content was up to 20wt%. FESEM results confirmed that strong interactions were existed between PLA and TPU phases, which were benefit for the improvement of PLA/TPU fibers’ mechanical properties. Results of tensile testing demonstrated that TPU could improve the toughness of fibers effectively and the elongation-at-break of fibers increased from 2.2% of PLA to 203.9% of PLA/TPU.

Preparation of Polyamide 5,6 (PA56) Fibers and its Mechanical Properties

2014 ◽  
Vol 937 ◽  
pp. 86-91 ◽  
Author(s):  
Yassir A. Eltahir ◽  
Haroon A.M. Saeed ◽  
Yu Min Xia ◽  
Yi Min Wang
Keyword(s):  
Mechanical Properties ◽  
Molecular Orientation ◽  
Draw Ratio ◽  
Melt Spinning ◽  
Tensile Modulus ◽  
Fiber Axis ◽  
Elongation At Break ◽  
Significant Difference ◽  
Hot Drawing ◽  
Melt Spinning Technique

Polyamide 5,6 (PA56) fibers were successfully prepared by melt-spinning technique. PA56 fibers were subjected to hot drawing process at different draw ratio and temperature. The effect of the drawing conditions on their mechanical properties such as tenacity, tensile modulus and breaking elongation were investigated by means of tensile test measurements. The results revealed that the tenacity and tensile modulus were found to be increased, while the elongation at break decreased with the draw ratio. The improvements of the mechanical properties could be attributed to the enhanced of the molecular orientation along the fiber axis and an increase in crystallinity. On the other hand, the PA56 fibers mechanical properties do not show significant difference with the drawing temperatures.

Preparation and Mechanical Properties of Zein/PVA Nanofibrous Membranes

2012 ◽  
Vol 466-467 ◽  
pp. 391-395
Author(s):  
Feng Xia Liu ◽  
Yong Jia Liu ◽  
Hong Li Cai ◽  
Jia Shuang Luan ◽  
Mei Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Testing ◽  
Mechanical Characterization ◽  
Scanning Calorimetry ◽  
Factors Affecting ◽  
Fibrous Membranes ◽  
Dsc Method ◽  
Morphology And Mechanical Properties ◽  
Significant Factors

This paper describes the morphology and mechanical properties of novel electrospun zein based fibrous membranes. From the results, due to adding PVA, it was found that the electrospun fibers of zein can turn into a new strong membrane. The fibrous membranes were characterized by tensile testing, scanning electron microscopy(SEM) and differential scanning calorimetry(DSC). Effect of PVA was analyzed as one of the most significant factors affecting the mechanical characterization of fibrous membranes. The compatibility of zein/PVA nanofibrous were also analyzed by using DSC method.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

Mechanical Characterization of UV Photopolymerized PMMA with Different Photo-Initiator Concentration

2021 ◽  
Vol 903 ◽  
pp. 11-16
Author(s):  
M.A. Manjunath ◽  
K. Naveen ◽  
Prakash Vinod ◽  
N. Balashanmugam ◽  
M.R. Shankar
Keyword(s):  
Mechanical Properties ◽  
Light Source ◽  
Polymethyl Methacrylate ◽  
Biomedical Applications ◽  
Mechanical Characterization ◽  
Uv Light ◽  
Curing Time ◽  
Uv Led ◽  
Pmma Resin

Polymethyl methacrylate (PMMA) is one among few known photo-polymeric resin useful in lithography for fabricating structures having better mechanical properties to meet the requirement in electronics and biomedical applications. This study explores the effect of Photo Initiator (PI) concentration and also curing time on strength and hardness of Polymethyl methacrylate (PMMA) obtained by UV photopolymerization of Methyl methacrylate (MMA) monomer. The UV LED light source operating at the wavelength of 364 nm is used with Benzoin Ethyl Ether (BEE) as photo initiator. The curing of PMMA resin is supported with peltier cooling device placed at the bottom of the UV light source. The characterisation study of UV photo cured PMMA is analysed through nano indenter (Agilent Technologies-G200). The current work investigates the influence of PI concentration and curing time in achieving maximum mechanical properties for UV photopolymerized PMMA.

Synthesis and Characterization of Mnbi Magnetic Alloy via Two Different Processing Routes

2021 ◽  
Vol 875 ◽  
pp. 76-80
Author(s):  
Hifsa Mazhar ◽  
Wilayat Hussain
Keyword(s):  
Heat Treatment ◽  
Melt Spinning ◽  
Treatment Time ◽  
Magnetic Energy ◽  
Microstructural Characterization ◽  
Temperature Phase ◽  
Magnetic Alloy ◽  
Positive Temperature ◽  
Melt Spinning Technique

Manganese bismuth alloy has gained importance due to its rare earth free elements, positive temperature coefficient and unique magnetic properties. Low temperature phase (LTP) MnBi was successfully prepared by arc melting with subsequent heat treatments and melt spinning technique followed by heat treatment for different durations. LTP MnBi formation was confirmed using XRD analysis and microstructural characterization of the samples was done using field emission scanning electron microscope. MnBi with greater LTP amount was formed by melt spinning route when compared with its counter arc melted one. Magnetic energy density of LTP MnBi formed by melt spinning technique with different heat treatment time was studied.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

scholarly journals Synthesis and characterization of PIL/pNIPAAm hybrid hydrogels

2016 ◽  
Vol 2 (1) ◽  
pp. 1-4
Author(s):  
Sylvia Pfensig ◽  
Daniela Arbeiter ◽  
Klaus-Peter Schmitz ◽  
Niels Grabow ◽  
Thomas Eickner ◽  
...  
Keyword(s):  
Mechanical Characterization ◽  
Heating Temperature ◽  
Controlled Drug Release ◽  
Solution Temperature ◽  
Scanning Calorimetry ◽  
Critical Solution Temperature ◽  
Temperature Range ◽  
Hybrid Hydrogels ◽  
Higher Temperature

AbstractIn this study, varying amounts of NIPAAm and an ionic liquid (IL), namely 1-vinyl-3-isopropylimidazolium bromide ([ViPrIm]+[Br]−), have been used to synthesize hybrid hydrogels by radical emulsion polymerization. Amounts of 70/30%, 50/50%, 30/70%, 15/85% and 5/95% (wt/wt) of PIL/pNIPAAm were used to produce hybrid hydrogels as well as the parental hydrogels. The adhesive strength was investigated and evaluated for mechanical characterization. Thermal properties of resulting hydrogels have been investigated using differential scanning calorimetry (DSC) in a default heating temperature range (heating rate 10 K min−1). The presence of poly ionic liquids (PIL) in the polymer matrix leads to a moved LCST (lower critical solution temperature) to a higher temperature range for certain hybrid hydrogels PIL/pNIPAAm. While pNIPAAm exhibits an LCST at 33.9 ± 0.3°C, PIL/pNIPAAm 5/95% and PIL/pNIPAAm 15/85% were found to have LCSTs at 37.6 ± 0.9°C and 52 ± 2°C, respectively. This could be used for controlled drug release that goes along with increasing body temperature in response to an implantation caused infection.

scholarly journals STRUCTURAL AND MECHANICAL CHARACTERIZATION OF DEFORMED POLYMER USING CONFOCAL RAMAN MICROSCOPY AND DSC

2016 ◽  
Vol 3 ◽  
pp. 47-50
Author(s):  
Birgit Neitzel ◽  
Florian Aschermayer ◽  
Milan Kracalik ◽  
Sabine Hild
Keyword(s):  
Differential Scanning Calorimetry ◽  
Raman Spectroscopy ◽  
Mechanical Characterization ◽  
Polymer Chains ◽  
Polymer Materials ◽  
Confocal Raman Microscopy ◽  
Micro Structure ◽  
Scanning Calorimetry ◽  
Confocal Raman

Polymers have various interesting properties, which depend largely on their inner structure. One way to influence the macroscopic behaviour is the deformation of the polymer chains, which effects the change in microstructure. For analyzing the microstructure of non-deformed and deformed polymer materials, Raman spectroscopy as well as differential scanning calorimetry (DSC) were used. In the present study we compare the results for crystallinity measurements of deformed polymers using both methods in order to characterize the differences in micro-structure due to deformation. The study is ongoing, and we present the results of the first tests.

scholarly journals THE PHYSICOCHEMICAL CHARACTERISTICS OF RECYCLED-PLASTIC PELLETS OBTAINED FROM DISPOSABLE FACE MASK WASTES

2021 ◽  
Vol 23 (1) ◽  
pp. 16
Author(s):  
Vienna Saraswaty ◽  
Rossy Choerun Nissa ◽  
Bonita Firdiana ◽  
Akbar Hanif Dawam Abdullah
Keyword(s):  
Tensile Strength ◽  
Physicochemical Characterization ◽  
Face Mask ◽  
Physicochemical Characteristics ◽  
Scanning Calorimetry ◽  
Elongation At Break ◽  
Ft Ir ◽  
The Government ◽  
Plastic Pellets

THE PHYSICOCHEMICAL CHARACTERISTICS OF RECYCLED-PLASTIC PELLETS OBTAINED FROM DISPOSABLE FACE MASK WASTES. The government policy to wear a face mask during the COVID-19 pandemic has increased disposable face mask wastes. Thus, to reduce such wastes, it is necessary to evaluate the physicochemical characteristics of disposable face masks wastes before the recycling process and the recycled products. In this study, physicochemical characterization of the 3-ply disposable face masks and the recycled plastic pellets after disinfection using 0.5% v/v sodium hypochlorite were evaluated. A set of parameters including the characterization of surface morphology by a scanning electron microscope (SEM), functional groups properties by a fourier transform infra-red spectroscopy (FT-IR), thermal behavior by a differential scanning calorimetry (DSC), tensile strength and elongation at break were evaluated. The surface morphological of each layer 3-ply disposable face mask showed that the layers were composed of non-woven fibers. The FT-IR evaluation revealed that 3-ply disposable face mask was made from a polypropylene. At the same time, the DSC analysis found that the polypropylene was in the form of homopolymer. The SEM analysis showed that the recycled plastic pellets showed a rough and uneven surface. The FT-IR, tensile strength and elongation at break of the recycled plastic pellets showed similarity with a virgin PP type CP442XP and a recycled PP from secondary recycling PP (COPLAST COMPANY). In summary, recycling 3-ply disposable face mask wastes to become plastic pellets is recommended for handling disposable face mask wastes problem.

Sign in / Sign up

Export Citation Format

Share Document