A 10-bit 200 MS/s pipelined ADC with parallel sampling and switched op-amp sharing technique

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
D.S. Shylu Sam ◽  
P. Sam Paul
Keyword(s):  
Power Consumption ◽  
Supply Voltage ◽  
Sampling Technique ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Pipelined Adc ◽  
Content Type ◽  
Op Amp ◽  
Op Amps ◽  
Parallel Sampling

Purpose In parallel sampling method, the size of the sampling capacitor is reduced to improve the bandwidth of the ADC. Design/methodology/approach Various low-power techniques for 10-bit 200MS/s pipelined analog-to-digital converter (ADC) are presented. This work comprises two techniques including parallel sampling and switched op-amp sharing technique. Findings This paper aims to study the effect of parallel sampling and switched op-amp sharing techniques on power consumption in pipelined ADC. In switched op-amp sharing technique, the numbers of op-amps used in the stages are reduced. Because of the reduction in the size of capacitors in parallel sampling technique and op-amps in the switched op-amp sharing technique, the power consumption of the proposed pipelined ADC is reduced to a greater extent. Originality/value Simulated the 10-bit 200MS/s pipelined ADC with complementary metal oxide semiconductor process and the simulation results shows a maximum differential non-linearity of +0.31/−0.31 LSB and the maximum integral non-linearity (of +0.74/−0.74 LSB with 62.9 dB SFDR, 55.90 dB SNDR and ENOB of 8.99 bits, respectively, for 18mW power consumption with the supply voltage of 1.8 V.

A 4:1 multiplexer using low-power high-speed domino technique for large fan-in gates using FinFET

Circuit World ◽  
2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Sandeep Garg ◽  
Tarun Kumar Gupta
Keyword(s):  
Low Power ◽  
High Speed ◽  
Supply Voltage ◽  
Average Power ◽  
Complementary Metal Oxide Semiconductor ◽  
Propagation Delay ◽  
Oxide Semiconductor ◽  
Content Type ◽  
Maximum Delay ◽  
Average Power Consumption

Purpose This paper aims to propose a new fin field-effect transistor (FinFET)-based domino technique low-power series connected foot-driven transistors logic in 32 nm technology and examine its performance parameters by performing transient analysis. Design/methodology/approach In the proposed technique, the leakage current is reduced at footer node by a division of current to improve the performance of the circuit in terms of average power consumption, propagation delay and noise margin. Simulation of existing and proposed techniques are carried out in FinFET and complementary metal-oxide semiconductor technology at FinFET 32 nm technology for 2-, 4-, 8- and 16-input domino OR gates on a supply voltage of 0.9 V using HSPICE. Findings The proposed technique shows maximum power reduction of 77.74% in FinFET short gate (SG) mode in comparison with current-mirror-based process variation tolerant (CPVT) technique and maximum delay reduction of 51.34% in low power (LP) mode in comparison with CPVT technique at a frequency of 100 MHz. The unity noise gain of the proposed circuit is 1.10× to 1.54× higher in comparison with different existing techniques in FinFET SG mode and 1.11× to 1.71× higher in FinFET LP mode. The figure of merit of the proposed circuit is up to 15.77× higher in comparison with existing domino techniques. Originality/value The research proposes a new FinFET-based domino technique and shows improvement in power, delay, area and noise performance. The proposed design can be used for implementing high-speed digital circuits such as microprocessors and memories.

scholarly journals A Chopper Stabilization Audio Instrumentation Amplifier for IoT Applications

2020 ◽  
Vol 10 (2) ◽  
pp. 13 ◽  
Author(s):  
Jamel Nebhen ◽  
Pietro M. Ferreira ◽  
Sofiene Mansouri
Keyword(s):  
Power Consumption ◽  
Silicon Nanowires ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Instrumentation Amplifier ◽  
Chopper Stabilization ◽  
Iot Applications ◽  
Trade Offs

A low-noise instrumentation amplifier dedicated to a nano- and micro-electro-mechanical system (M&NEMS) microphone for the use in Internet of Things (IoT) applications is presented. The piezoresistive sensor and the electronic interface are respectively, silicon nanowires and an instrumentation amplifier. To design an instrumentation amplifier for IoT applications, different trade-offs are discussed like power consumption, gain, noise and sensitivity. Because the most critical noisy block is the amplifier, a delay-time chopper stabilization (CHS) technique is implemented around it to eliminate its offset and 1/f noise. The low-noise instrumentation amplifier is implemented in a 65-nm CMOS (Complementary metal–oxide–semiconductor) technology. The supply voltage is 2.5 V while the power consumption is 0.4 mW and the core area is 1 mm2. The circuit of the M&NEMS microphone and the amplifier was fabricated and measured. From measurement results over a signal bandwidth of 20 kHz, it achieves a signal-to-noise ratio (SNR) of 77 dB.

scholarly journals An E-Band 21-dB Variable-Gain Amplifier with 0.5-V Supply in 40-nm CMOS

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 804
Author(s):  
Gibeom Shin ◽  
Kyunghwan Kim ◽  
Kangseop Lee ◽  
Hyun-Hak Jeong ◽  
Ho-Jin Song
Keyword(s):  
Power Consumption ◽  
Frequency Band ◽  
Noise Figure ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Operating Frequency ◽  
Variable Gain Amplifier ◽  
Variable Gain ◽  
Operating Frequency Band ◽  
Shunt Capacitors

This paper presents a variable-gain amplifier (VGA) in the 68–78 GHz range. To reduce DC power consumption, the drain voltage was set to 0.5 V with competitive performance in the gain and the noise figure. High-Q shunt capacitors were employed at the gate terminal of the core transistors to move input matching points for easy matching with a compact transformer. The four stages amplifier fabricated in 40-nm bulk complementary metal oxide semiconductor (CMOS) showed a peak gain of 24.5 dB at 71.3 GHz and 3‑dB bandwidth of more than 10 GHz in 68–78 GHz range with approximately 4.8-mW power consumption per stage. Gate-bias control of the second stage in which feedback capacitances were neutralized with cross-coupled capacitors allowed us to vary the gain by around 21 dB in the operating frequency band. The noise figure was estimated to be better than 5.9 dB in the operating frequency band from the full electromagnetic (EM) simulation.

scholarly journals Investigation of PVT-Aware STT-MRAM Sensing Circuits for Low-VDD Scenario

Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 551
Author(s):  
Zhongjian Bian ◽  
Xiaofeng Hong ◽  
Yanan Guo ◽  
Lirida Naviner ◽  
Wei Ge ◽  
...  
Keyword(s):  
Nonvolatile Memory ◽  
High Speed ◽  
Low Voltage ◽  
Supply Voltage ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Current Mode ◽  
Cmos Technology ◽  
Oxide Semiconductor

Spintronic based embedded magnetic random access memory (eMRAM) is becoming a foundry validated solution for the next-generation nonvolatile memory applications. The hybrid complementary metal-oxide-semiconductor (CMOS)/magnetic tunnel junction (MTJ) integration has been selected as a proper candidate for energy harvesting, area-constraint and energy-efficiency Internet of Things (IoT) systems-on-chips. Multi-VDD (low supply voltage) techniques were adopted to minimize energy dissipation in MRAM, at the cost of reduced writing/sensing speed and margin. Meanwhile, yield can be severely affected due to variations in process parameters. In this work, we conduct a thorough analysis of MRAM sensing margin and yield. We propose a current-mode sensing amplifier (CSA) named 1D high-sensing 1D margin, high 1D speed and 1D stability (HMSS-SA) with reconfigured reference path and pre-charge transistor. Process-voltage-temperature (PVT) aware analysis is performed based on an MTJ compact model and an industrial 28 nm CMOS technology, explicitly considering low-voltage (0.7 V), low tunneling magnetoresistance (TMR) (50%) and high temperature (85 °C) scenario as the worst sensing case. A case study takes a brief look at sensing circuits, which is applied to in-memory bit-wise computing. Simulation results indicate that the proposed high-sensing margin, high speed and stability sensing-sensing amplifier (HMSS-SA) achieves remarkable performance up to 2.5 GHz sensing frequency. At 0.65 V supply voltage, it can achieve 1 GHz operation frequency with only 0.3% failure rate.

Review: Static and Dynamic Analysis Methods for Multi-Branch Biasing Circuits

2018 ◽  
Vol 27 (13) ◽  
pp. 1830008
Author(s):  
Jin Wu ◽  
Pengfei Dai ◽  
Jie Peng ◽  
Lixia Zheng ◽  
Weifeng Sun
Keyword(s):  
Feedback Loop ◽  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Oxide Semiconductor ◽  
Critical Parameters ◽  
Cmos Process ◽  
Stable Equilibrium Point ◽  
Static And Dynamic Analysis ◽  
Text Structures ◽  
Different Types

The fundamental theories and primary structures for the multi-branch self-biasing circuits are reviewed in this paper. First, the [Formula: see text]/[Formula: see text] and [Formula: see text]/[Formula: see text] structures illustrating the static current definition mechanism are presented, including the conditions of starting up and entering into a stable equilibrium point. Then, the AC method based on the loop gain evaluation is utilized to analyze different types of circuits. On this basis, the laws which can couple the branches of self-biasing circuits to construct a suitable close feedback loop are summarized. By adopting Taiwan Semiconductor Manufacturing Company (TSMC)’s 0.18[Formula: see text][Formula: see text]m complementary metal–oxide–semiconductor (CMOS) process with 1.8[Formula: see text][Formula: see text] supply voltage, nearly all the circuits mentioned in the paper are simulated in the same branch current condition, which is close to the corresponding calculated results. Therefore, the methods summarized in this paper can be utilized for distinguishing, constructing, and optimizing critical parameters for various structures of the self-biasing circuits.

A new approach to bypass wire crossing problem in QCA nano technology

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ali Majeed ◽  
Esam Alkaldy
Keyword(s):  
Power Dissipation ◽  
Single Layer ◽  
Complementary Metal Oxide Semiconductor ◽  
Full Adder ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Nano Technology ◽  
New Approach ◽  
Content Type ◽  
Wire Crossing

Purpose This study aims to replace current multi-layer and coplanar wire crossing methods in QCA technology to avoid fabrication difficulties caused by them. Design/methodology/approach Quantum-dot cellular automata (QCA) is one of the newly emerging nanoelectronics technology tools that is proposed as a good replacement for complementary metal oxide semiconductor (CMOS) technology. This technology has many challenges, among them being component interconnection and signal routing. This paper will propose a new wire crossing method to enhance layout use in a single layer. The presented method depends on the central cell clock phase to enable two signals to cross over without interference. QCADesigner software is used to simulate a full adder circuit designed with the proposed wire crossing method to be used as a benchmark for further analysis of the presented wire crossing approach. QCAPro software is used for power dissipation analysis of the proposed adder. Findings A new cost function is presented in this paper to draw attention to the fabrication difficulties of the technology when designing QCA circuits. This function is applied to the selected benchmark circuit, and the results show good performance of the proposed method compared to others. The improvement is around 59, 33 and 75% compared to the best reported multi-layer wire crossing, coplanar wire crossing and logical crossing, respectively. The power dissipation analysis shows that the proposed method does not cause any extra power consumption in the circuit. Originality/value In this paper, a new approach is developed to bypass the wire crossing problem in the QCA technique.

Design of Low Power Integrated CMOS Potentiometric Biosensor for Direct Electronic Detection of DNA Hybridization

2014 ◽  
Vol 67 (1) ◽  
Author(s):  
Wong How Hwan ◽  
Vinny Lam Siu Fan ◽  
Yusmeeraz Yusof
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Dna Hybridization ◽  
Point Of Care ◽  
Complementary Metal Oxide Semiconductor ◽  
Cmos Technology ◽  
Channel Length ◽  
Electrical Signal ◽  
Oxide Semiconductor ◽  
Detection Circuit

The purpose of this research is to design a low power integrated complementary metal oxide semiconductor (CMOS) detection circuit for charge-modulated field-effect transistor (CMFET) and it is used for the detection of deoxyribonucleic acid (DNA) hybridization. With the available CMOS technology, it allows the realization of complete systems which integrate the sensing units and transducing elements in the same device. Point-of-care (POC) testing device is a device that allows anyone to operate anywhere and obtain immediate results. One of the important features of POC device is low power consumption because it is normally battery-operated. The power consumption of the proposed integrated CMOS detection circuit requires only 14.87 mW. The detection circuit will amplify the electrical signal that comes from the CMFET to a specified level in order to improve the recording characteristics of the biosensor. Self-cascode topology was used in the drain follower circuit in order to reduce the channel length modulation effect. The proposed detection circuit was designed with 0.18µm Silterra CMOS fabrication process and simulated under Cadence Simulation Tool. 

scholarly journals DIGITAL CONTROLLED OSCILLATOR (DCO) FOR ALL DIGITAL PHASE-LOCKED LOOP (ADPLL) – A REVIEW

2019 ◽  
Vol 82 (1) ◽  
Author(s):  
Florence Choong ◽  
Mamun Ibne Reaz ◽  
Mohamad Ibrahim Kamaruzzaman ◽  
Md. Torikul Islam Badal ◽  
Araf Farayez ◽  
...  
Keyword(s):  
Supply Voltage ◽  
Complementary Metal Oxide Semiconductor ◽  
Phase Locked Loop ◽  
Cmos Technology ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
Process Technology ◽  
Chip Area ◽  
Digital Phase ◽  
Low Power Dissipation

Digital controlled oscillator (DCO) is becoming an attractive replacement over the voltage control oscillator (VCO) with the advances of digital intensive research on all-digital phase locked-loop (ADPLL) in complementary metal-oxide semiconductor (CMOS) process technology. This paper presents a review of various CMOS DCO schemes implemented in ADPLL and relationship between the DCO parameters with ADPLL performance. The DCO architecture evaluated through its power consumption, speed, chip area, frequency range, supply voltage, portability and resolution. It can be concluded that even though there are various schemes of DCO that have been implemented for ADPLL, the selection of the DCO is frequently based on the ADPLL applications and the complexity of the scheme. The demand for the low power dissipation and high resolution DCO in CMOS technology shall remain a challenging and active area of research for years to come. Thus, this review shall work as a guideline for the researchers who wish to work on all digital PLL.

Performance analysis of differential spin hall effect (DSHE)-MRAM-based logic gates

Circuit World ◽  
2019 ◽  
Vol 45 (4) ◽  
pp. 300-310
Author(s):  
Piyush Tankwal ◽  
Vikas Nehra ◽  
Sanjay Prajapati ◽  
Brajesh Kumar Kaushik
Keyword(s):  
Hall Effect ◽  
Random Access ◽  
Magnetic Tunnel Junction ◽  
Complementary Metal Oxide Semiconductor ◽  
Logic Gates ◽  
Cmos Technology ◽  
Spin Transfer Torque ◽  
Spin Hall Effect ◽  
Oxide Semiconductor ◽  
Content Type

Purpose The purpose of this paper is to analyze and compare the characteristics of hybrid conventional complementary metal oxide semiconductor/magnetic tunnel junction (CMOS/MTJ) logic gates based on spin transfer torque (STT) and differential spin Hall effect (DSHE) magnetic random access memory (MRAM). Design/methodology/approach Spintronics technology can be used as an alternative to CMOS technology as it is having comparatively low power dissipation, non-volatility, high density and high endurance. MTJ is the basic spin based device that stores data in form of electron spin instead of charge. Two mechanisms, namely, STT and SHE, are used to switch the magnetization of MTJ. Findings It is observed that the power consumption in DSHE based logic gates is 95.6% less than the STT based gates. DSHE-based write circuit consumes only 5.28 fJ energy per bit. Originality/value This paper describes how the DSHE-MRAM is more effective for implementing logic circuits in comparison to STT-MRAM.

Sign in / Sign up

Export Citation Format

Share Document