Characterization of Magnesium/Carbon Nanotubes Composites Synthesized Using an Innovative Solidification Method

Materials ◽  
2004 ◽  
Author(s):  
C. S. Goh ◽  
M. Gupta ◽  
J. Wei ◽  
L. C. Lee ◽  
K. W. Lim
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Coefficient Of Thermal Expansion ◽  
Weight Fraction ◽  
Mechanical Analysis ◽  
Extrusion Ratio ◽  
Pure Magnesium ◽  
Melt Deposition ◽  
Deposition Technology

In the study reported in this paper, carbon nanotubes of up to two per cent by weight were added as reinforcement to the pure magnesium. A disintegrated melt deposition technology was employed as the solidification method and the ingots produced were subsequently hot extruded at a temperature of 350 °C and extrusion ratio of 20:1. The thermo-mechanical analysis showed a reduction in the coefficient of thermal expansion due to the presence of the carbon nanotubes. Examination of the mechanical properties indicated that with increasing amount of carbon nanotubes reinforcement added, there was a significant improvement in the performance of pure magnesium. An attempt is made to correlate the weight fraction of the carbon nanotubes with the properties of the resulting magnesium nanocomposite material.

Synthesis and Characterization of Hybrid Aluminum Composites Reinforced with Ni Particulates and Interconnected Fe Mesh

2006 ◽  
Vol 111 ◽  
pp. 39-42 ◽  
Author(s):  
W.L.Eugene Wong ◽  
Manoj Gupta ◽  
C.Y.H. Lim
Keyword(s):  
Coefficient Of Thermal Expansion ◽  
Pure Aluminum ◽  
Matrix Material ◽  
Aluminum Matrix ◽  
Hot Extrusion ◽  
Microstructural Characterization ◽  
Mechanical Analysis ◽  
The Matrix ◽  
Melt Deposition

In this study, pure aluminum reinforced with interconnected galvanized iron mesh and Ni particulates was synthesized using an innovative disintegrated melt deposition technique followed by hot extrusion. Microstructural characterization of composite samples showed uniform distribution of Ni and Al-Ni based intermetallic particulates in the matrix material, good interfacial integrity of aluminum matrix with iron mesh and Ni particulates and the presence of minimal porosity. Results of thermal mechanical analysis indicate a decrease in the average coefficient of thermal expansion of the aluminum matrix with the use of hybrid reinforcements. Mechanical characterization also revealed that the coupled use of galvanized iron mesh and Ni particulates lead to an improvement in the hardness, dynamic modulus, 0.2% yield strength and UTS but ductility was adversely affected. An attempt is made to correlate the use of hybrid reinforcements with the improved properties exhibited by the synthesized composites.

scholarly journals Effect of SWCNT-Tuball Paper on the Lightning Strike Protection of CFRPs and Their Selected Mechanical Properties

Materials ◽  
2021 ◽  
Vol 14 (11) ◽  
pp. 3140
Author(s):  
Kamil Dydek ◽  
Anna Boczkowska ◽  
Rafał Kozera ◽  
Paweł Durałek ◽  
Łukasz Sarniak ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Electrical Conductivity ◽  
Copper Foil ◽  
Impact Resistance ◽  
Mechanical Analysis ◽  
Lightning Strike ◽  
Single Wall Carbon Nanotubes ◽  
Carbon Fibre Reinforced Polymer ◽  
The Impact

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt% or 90 wt% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

Enhancing the Thermal and Mechanical Characteristics of Polyvinyl Alcohol (PVA)-Hemp Protein Particles (HPP) Composites

2021 ◽  
Vol 36 (2) ◽  
pp. 137-143
Author(s):  
S. A. Awad
Keyword(s):  
Mechanical Properties ◽  
Elevated Temperatures ◽  
Composite Films ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Decomposition Temperature ◽  
Scanning Calorimetry ◽  
Solution Casting Method ◽  
Protein Particles

Abstract This paper aims to describe the thermal, mechanical, and surface properties of a PVA/HPP blend whereby the film was prepared using a solution casting method. The improvements in thermal and mechanical properties of HPP-based PVA composites were investigated. The characterization of pure PVA and PVA composite films included tensile tests, thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). The results of TGA and DSC indicated that the addition of HPP increased the thermal decomposition temperature of the composites. Mechanical properties are significantly improved in PVA/HPP composites. The thermal stability of the PVA composite increased with the increase of HPP filler content. The tensile strength increased from 15.74 ± 0.72 MPa to 27.54 ± 0.45 MPa and the Young’s modulus increased from 282.51 ± 20.56 MPa to 988.69 ± 42.64 MPa for the 12 wt% HPP doped sample. Dynamic mechanical analysis (DMA) revealed that at elevated temperatures, enhanced mechanical properties because of the presence of HPP was even more noticeable. Morphological observations displayed no signs of agglomeration of HPP fillers even in composites with high HPP loading.

scholarly journals Polymeric Composites Based on Polyurea Matrix Reinforced with Carbon Nanotubes

2017 ◽  
Vol 54 (1) ◽  
pp. 41-44 ◽  
Author(s):  
Maria Adina Vulcan ◽  
Celina Damian ◽  
Paul Octavian Stanescu ◽  
Eugeniu Vasile ◽  
Razvan Petre ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Thermal Stability ◽  
Scanning Electron Microscopy ◽  
Tensile Tests ◽  
Mechanical Analysis ◽  
Multi Walled Carbon Nanotubes ◽  
Walled Carbon Nanotubes ◽  
Scanning Electron

This paper deals with the synthesis of polyurea and its use as polymer matrix for nanocomposites reinforced with multi-walled carbon nanotubes (MWCNT). Two types of materials were obtained during this research, the first cathegory uses the polyurea as matrix and the second one uses a mixture between epoxy resin and polyurea. The nanocomposites were characterized by Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA), Scanning Electron Microscopy (SEM) and Tensile Tests .The elastomeric features of nanocomposites were highlighted by the results which showed low value of Tg. Also higher thermal stability with ~40oC compared with commercial products (M20) were observed, but lower mechanical properties compared to neat polyurea.

Effect of Thermomechanical Processing on Grain Size, Texture and Mechanical Properties of Pure Magnesium

2020 ◽  
Vol 985 ◽  
pp. 97-108
Author(s):  
Mouhamadou Moustapha Sarr ◽  
Motohiro Yuasa ◽  
Hiroyuki Miyamoto
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Stress ◽  
Thermomechanical Processing ◽  
Pure Magnesium ◽  
Grain Structure ◽  
Misorientation Distribution ◽  
Processed Material ◽  
Texture Characterization

This study aims to investigate the effect of processing routes (A and Bc) and temperature on microstructure, texture and mechanical properties of pure magnesium was studied in this research. An extruded pure magnesium (~99,9 %) was subjected to severe plastic deformation (SPD) by ECAP. Deformation was conducted at 523K and 473K and two different processing routes (A and Bc) were used to control the texture. The microstructure and texture characterization of the pressed materials were carried out. It was found that the microstructure displayed a bimodal grain structure after two passes and then became homogeneous after four passes following both routes A and Bc. The misorientation distribution was examined and the results revealed that the fraction of high angle grain boundaries (HAGB) was higher at temperature 473K. The texture was randomized following route Bc whereas it became strengthened in route A after four passes. According to the Hall-Petch (HP) relationship, the yield stress of polycrystalline metals increases with a decrease in grain size. In this study, a positive slope k was achieved in the strengthened texture while a negative one was obtained in the softened texture. The ductility of ECAP processed material was considerably improved (from 23% to 38%) without sacrificing the yield stress by route Bc at 423K.

scholarly journals Properties and Characterization of a PLA–Chitin–Starch Biodegradable Polymer Composite

Polymers ◽  
2019 ◽  
Vol 11 (10) ◽  
pp. 1656 ◽  
Author(s):  
Olaiya ◽  
Surya ◽  
Oke ◽  
Rizal ◽  
Sadiku ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Degradation Process ◽  
Mechanical Analysis ◽  
Poly Lactic Acid ◽  
Dynamic Mechanical ◽  
Properties And Characterization ◽  
Percentage Weight ◽  
Specific Order ◽  
Starch Blends

This paper presents a comparison on the effects of blending chitin and/or starch with poly(lactic acid) (PLA). Three sets of composites (PLA–chitin, PLA–starch and PLA–chitin–starch) with 92%, 94%, 96% and 98% PLA by weight were prepared. The percentage weight (wt.%) amount of the chitin and starch incorporated ranges from 2% to 8%. The mechanical, dynamic mechanical, thermal and microstructural properties were analyzed. The results from the tensile strength, yield strength, Young's modulus, and impact showed that the PLA–chitin–starch blend has the best mechanical properties compared to PLA–chitin and PLA–starch blends. The dynamic mechanical analysis result shows a better damping property for PLA–chitin than PLA–chitin–starch and PLA–starch. On the other hand, the thermal property analysis from thermogravimetry analysis (TGA) shows no significant improvement in a specific order, but the glass transition temperature of the composite increased compared to that of neat PLA. However, the degradation process was found to start with PLA–chitin for all composites, which suggests an improvement in PLA degradation. Significantly, the morphological analysis revealed a uniform mix with an obvious blend network in the three composites. Interestingly, the network was more significant in the PLA–chitin–starch blend, which may be responsible for its significantly enhanced mechanical properties compared with PLA–chitin and PLA–starch samples.

scholarly journals Effective reinforcements for thermoplastics based on carbon nanotubes of oil fly ash

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Numan Salah ◽  
Abdulrahman Muhammad Alfawzan ◽  
Abdu Saeed ◽  
Ahmed Alshahrie ◽  
Waleed Allafi
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Fly Ash ◽  
Young’S Modulus ◽  
Raw Materials ◽  
Young's Modulus ◽  
Weight Fraction ◽  
Low Weight ◽  
Oil Fly Ash

AbstractCarbon nanotubes (CNTs) are widely investigated for preparing polymer nanocomposites, owing to their unique mechanical properties. However, dispersing CNTs uniformly in a polymer matrix and controlling their entanglement/agglomeration are still big technical challenges to be overcome. The costs of their raw materials and production are also still high. In this work, we propose the use of CNTs grown on oil fly ash to solve these issues. The CNTs of oil fly ash were evaluated as reinforcing materials for some common thermoplastics. High-density polyethylene (HDPE) was mainly reinforced with various weight fractions of CNTs. Xylene was used as a solvent to dissolve HDPE and to uniformly disperse the CNTs. Significantly enhanced mechanical properties of HDPE reinforced at a low weight fraction of these CNTs (1–2 wt.%), mainly the tensile strength, Young’s modulus, stiffness, and hardness, were observed. The tensile strength and Young’s modulus were enhanced by ~20 and 38%, respectively. Moreover, the nanoindentation results were found to be in support to these findings. Polycarbonate, polypropylene, and polystyrene were also preliminarily evaluated after reinforcement with 1 wt.% CNTs. The tensile strength and Young’s Modulus were increased after reinforcement with CNTs. These results demonstrate that the CNTs of the solid waste, oil fly ash, might serve as an appropriate reinforcing material for different thermoplastics polymers.

Characterization of Mechanical Properties of Carbon Nanotubes in Copper-Matrix Nanocomposites

2006 ◽  
Author(s):  
Seunghyun Baik ◽  
Byeongsoo Lim ◽  
Bumjoon Kim ◽  
Untae Sim ◽  
Seyoung Oh ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Carbon Nanotubes ◽  
Carbon Nanotube ◽  
Pure Copper ◽  
Copper Matrix ◽  
Mixing Process ◽  
Mechanical Mixing ◽  
Matrix Nanocomposites ◽  
Coated Carbon

Carbon nanotubes have received considerable attention because of their excellent mechanical properties. In this study, carbon nanotube - copper composites have been sintered by a mechanical mixing process. The interfacial bonding between nanotubes and the copper matrix was improved by coating nanotubes with nickel. Sintered pure copper samples were used as control materials. The displacement rate of nanotube-copper composites was found to increase at 200°C whereas that of nickel-coated nanotue-copper composites significantly decreased. The incorporation of carbon nanotubes and nickel-coated carbon nanotubes in the copper matrix decreased friction coefficients and increased the time up to the onset of scuffing compared with those of pure copper specimens.

Preparation and Characterization of Nanocrystalline Cellulose/Natural Rubber (NCC/Nr) Composites

2013 ◽  
Vol 712-715 ◽  
pp. 111-114 ◽  
Author(s):  
Tian Ming Gao ◽  
Mao Fang Huang ◽  
Rui Hong Xie ◽  
Hong Lian Chen
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Natural Rubber Latex ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Nanocrystalline Cellulose ◽  
Rubber Latex ◽  
Dynamic Mechanical ◽  
Surface Modified

Surface modified nanocrystalline cellulose (NCC) was prepared by silicon-69, and then blended into natural rubber latex to prepare nanocomposites. The nanocomposites properties of tensile properties, tear strength, morphology and thermal dynamic mechanical properties were measured by mechanical property testing, scanning electron microscopy (SEM), and dynamic mechanical analysis (DMA), respectively. The results showed that modified NCC is homogeneously distributed throughout NR matrix, which leads to the enhancement on mechanical properties. Moreover, the storage modulus (E) of modified nanocellulose filled NR is higher than unmodified nanocellulose filled NR, and the tanδ is reversed.

Sign in / Sign up

Export Citation Format

Share Document