Bétons à haute performance pour fabriquer des panneaux destinés à réparer des structures submergées

1993 ◽  
Vol 20 (4) ◽  
pp. 650-659 ◽  
Author(s):  
M. Sonebi ◽  
K. H. Khayat
Keyword(s):  
Compressive Strength ◽  
Silica Fume ◽  
High Performance ◽  
Steel Fibre ◽  
Concrete Durability ◽  
Freeze Thaw ◽  
Limestone Aggregate ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Economic Worth

The field of repair of submerged hydraulic structures (dams, stilling basins, lock chambers, and so forth) is becoming more and more important given the economic worth of such structures. Damage caused by abrasion can make it difficult to maintain such structures in service. The purpose of the study described in this paper was to develop durable high-performance concretes that can be used for manufacture of board for repair of abrasion-damaged surfaces. The board might also be placed on surfaces already repaired with colloidal concrete poured underwater. Two types of cement (Type 30 and Type 10) and two high-performance coarse aggregates (granite and dolomitic limestone) were used. The eight concrete mixes developed included a variety of additives and admixtures such as silica fume, steel fibre, latex, and superplasticizer. For precise characterization of the mixes, hydraulic abrasion tests, compressive strength tests, and freeze–thaw cycle resistance tests were performed. In addition, shrinkage, thermal expansion coefficient, and permeability of the concretes were measured; in some cases, the board might be subject to freeze–thaw cycles in structures partially emptied for repair or maintenance. Results show that high-performance concretes with very low water: cement ratio, good workability, and improved freeze–thaw cycle resistance can be manufactured. Concretes made with Type-30 cement, silica fume, and granite or limestone aggregate offer excellent hydraulic abrasion resistance (depth of erosion on the order of 1 mm after 72 h), compressive strength greater than 115 MPa after 91 days, and a freeze–thaw durability factor of more than 100%. Key words: abrasion, concrete, durability, steel fibre, silica fume, freeze–thaw cycle, latex, board, underwater repair.

scholarly journals Study on Strength Characteristics of Solidified Contaminated Soil under Freeze-Thaw Cycle Conditions

2018 ◽  
Vol 2018 ◽  
pp. 1-5 ◽  
Author(s):  
Qiang Wang ◽  
Jinyang Cui
Keyword(s):  
Electron Microscopy ◽  
Compressive Strength ◽  
Contaminated Soils ◽  
Unconfined Compressive Strength ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Strength Tests ◽  
Freeze Thaw Cycle ◽  
Microcosmic Mechanism ◽  
Scanning Electron

Cement solidification/stabilization is a commonly used method for the remediation of contaminated soils. The stability characteristics of solidified/stabilized contaminated soils under freeze-thaw cycle are very important. A series of tests, which include unconfined compressive strength tests, freeze-thaw cycle tests, and scanning electron microscopy (SEM) tests, are performed to study the variation law of strength characteristics and microstructure. It aims at revealing the microcosmic mechanism of solidified/stabilized Pb2+ contaminated soils with cement under freeze-thaw cycle. The results show that the unconfined compressive strength of the contaminated soils significantly improved with the increase of the cement content. The unconfined compressive strength of stabilized contaminated soils first increases with the increase of times of freeze-thaw cycle, and after reaching the peak, it decreases with the increase of times of freeze-thaw cycle. The results of the scanning electron microscopy tests are consistent with those of the unconfined compressive strength tests. This paper also reveals the microcosmic mechanism of the changes in engineering of the stabilized contaminated soils under freeze-thaw cycle.

The Effect of Freeze/Thaw Cycles on the Stability of Compounds in DMSO

2003 ◽  
Vol 8 (2) ◽  
pp. 210-215 ◽  
Author(s):  
Barbara A. Kozikowski ◽  
Thomas M. Burt ◽  
Debra A. Tirey ◽  
Lisa E. Williams ◽  
Barbara R. Kuzmak ◽  
...  
Keyword(s):  
High Throughput Screening ◽  
High Performance ◽  
Atmospheric Conditions ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Time Period ◽  
Freeze Thaw Cycle ◽  
Low Humidity ◽  
The Stability ◽  
Short Time

A diverse set of 320 compounds from the Procter & Gamble Pharmaceuticals organic compound repository was prepared as 20-mM DMSO solutions and stored at 4°C under argon in pressurized canisters to simulate a low-humidity environment. The plates were subjected to 25 freeze/thaw cycles while being exposed to ambient atmospheric conditions after each thaw to simulate the time and manner by which compound plates are exposed to the atmosphere during typical liquid-handling and high-throughput screening processes. High-performance liquid chromatography–mass spectrometry with evaporative light-scattering detection was used to quantitate the amount of compound remaining after every 5th freeze/thaw cycle. Control plates were stored either at room temperature under argon or at 4°C under argon without freeze/thaw cycling and were evaluated at the midpoint and the endpoint of the study. The study was conducted over a short time period (i.e., 7 weeks) to minimize the effect of compound degradation over time due to the exposure of the compounds to DMSO.The results from this study will be used to determine the maximum number of freeze/thaw cycles that can be achieved while maintaining acceptable compound integrity.(Journal of Biomolecular Screening 2003:210-215)

Les effets des caractéristiques du réseau de bulles d'air, du type de mûrissement, du truellage de surface et de la fumée de silice sur la résistance à l'écaillage d'un béton à haute performance

1996 ◽  
Vol 23 (6) ◽  
pp. 1260-1271
Author(s):  
Richard Gagné ◽  
Yvon Latreille ◽  
Jacques Marchand
Keyword(s):  
Silica Fume ◽  
High Performance ◽  
High Performance Concrete ◽  
Surface Finishing ◽  
Air Bubbles ◽  
Concrete Durability ◽  
Freeze Thaw ◽  
Spacing Factor ◽  
Entrained Air ◽  
Scaling Resistance

In Canada, high-performance concretes (HPCs) are increasingly used in construction and repair, particularly for its durability, which is distinctly superior compared with ordinary concrete. The current tendency is to provide for a spacing factor of air bubbles lower than 230 μm in all HPCs that are subjected to freeze–thaw cycles. This choice is basically the outcome of an ongoing controversy as to the necessity of providing a good network of entrained air bubbles to protect HPCs against freeze–thaw cycles. In the future, the optimal use of HPC will depend, among other factors, on a better understanding of minimal requirements regarding the characteristics of air voids to ensure a good behavior of HPCs under freeze–thaw cycles. The results of the investigation reported herein show that a spacing factor lower than approximately 500 μm can be sufficient to ensure a good resistance of HPCs to scaling. It is also shown that surface trawling, slump, and set-retarding agents have only secondary effects on the scaling resistance of HPCs. Silica fume and membrane curing have allowed to improve significantly the scaling resistance of the HPCs under investigation. Key words: high-performance concrete, durability, scaling, set-retarding agent, silica fume, surface finishing, curing, pumping, entrained air, spacing factor.

THE INFLUENCE OF FREEZE–THAW CYCLES ON UNCONFINED COMPRESSIVE STRENGTH OF CLAY SOILS TREATED WITH LIME

2015 ◽  
Vol 76 (1) ◽  
Author(s):  
Ali Akbar Firoozi ◽  
Mohd Raihan Taha ◽  
Ali Asghar Firoozi ◽  
Tanveer Ahmed Khan
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Conventional Technique ◽  
Silica Sand ◽  
Clay Soils ◽  
Unit Weight ◽  
Freeze Thaw ◽  
Long Term Stability ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

There are several questions that are not well understood with respect to the long-term stability characteristics of lime-treated clay soils in spite of being used as a conventional technique to improve the properties of clay soils. This paper investigates the influence of freeze-thaw cycles on the unconfined compressive strength of kaolinite and illite mixed with silica sand. The results of this study show that an increase in the number of freeze-thaw cycles decreases the unconfined compressive strength. The role of lime increasing the soil strength is more significant in the case of samples exposed to freeze-thaw cycles compared to those not exposed to freeze-thaw cycles. The effect of freeze-thaw cycles on the dry unit weight and moisture content is insignificant compared to unexposed samples. The maximum volumetric changes occurred in the first freeze-thaw cycle, and afterward, the rate of volume change decreased with an increase in freeze—thaw cycles.

scholarly journals Study on Application Effect of Sand Consolidating Agent for the Slope of Highway Subgrade in Season Frozen Zone

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Dongliang Zhang ◽  
Guangqing Yang ◽  
Xiaodi Niu ◽  
Lu Zhang ◽  
Zhijie Wang
Keyword(s):  
Compressive Strength ◽  
Friction Angle ◽  
Freeze Thaw ◽  
Direct Shear Tests ◽  
Thaw Cycle ◽  
Sand Body ◽  
Before And After ◽  
Freeze Thaw Cycle ◽  
Sandy Slope ◽  
Sand Particles

In deep season frozen areas, the solidified layer is easy to be destroyed due to the influence of freeze-thaw cycles after the surface layer of the sandy slope is solidified by chemical methods. In order to study the application effect of the new sand consolidating agent after solidifying sand body, the mechanism of strength formation was analyzed by scanning electron microscopy (SEM). The freeze-thaw cycle tests were carried out on sand consolidating samples. The direct shear tests and unconfined compressive strength tests were carried out before and after freeze-thaw cycles to analyze the freeze-thaw resistance of sand consolidating samples. The sand consolidation agent was tested on-site, and its strength was tested to observe its effect. The results showed that the adhesive membranes on the surface of sand particles were formed by the sand consolidating agent, which increased the cohesion and strength of sand particles. After freeze-thaw cycle tests, the cohesion, internal friction angle, and compressive strength of the solidified sand gradually decreased with increasing freeze-thaw cycles. The decreasing rate reduced from fast to slow and then tends to be stable. The failure mode of samples changed from brittle failure to plastic failure. The sand consolidating layer can effectively prevent collapse of the sandy slope. Combining with the external-soil spray seeding, the sand consolidation layer is beneficial to the growth of plants.

Comparison of Multiple Freeze-Thaw Cycles of High-Performance Concrete Test Beams and Concrete Beams Loaded Test

2013 ◽  
Vol 351-352 ◽  
pp. 570-573
Author(s):  
Zhi Qiang Li ◽  
Xian Chun Zheng ◽  
Xiao Hong Cong
Keyword(s):  
Mechanical Properties ◽  
Concrete Structure ◽  
High Performance ◽  
High Performance Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Structures ◽  
Experimental Basis ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

This study focuses on the following: analysis of the basic mechanical properties of freeze-thaw cycles BFRP composite; freeze-thaw cycle on BFRP reinforced concrete structures force performance; provide experimental basis for the the basalt FRP freeze-thaw environment concrete structure andtheoretical support.

Experiment Study on the Effect of GGBFS on Frost Resistance of Concrete

2014 ◽  
Vol 629-630 ◽  
pp. 207-212 ◽  
Author(s):  
Shi Yi Zhang ◽  
Ying Fang Fan ◽  
Qi Wang
Keyword(s):  
Electron Microscopy ◽  
High Performance ◽  
Plain Concrete ◽  
Industrial Wastes ◽  
X Ray Diffraction ◽  
X Ray ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
Scanning Electron

High volume utilization of industrial wastes and by products is the solution for high disposal coast. The anti-frost of high performance concrete is a key factor for safe utilization of concrete structure containing industrial wastes under severe environment. In this paper, to understand the property on anti-frost of high performance containing ground granulated blast furnace slag (GGBFS) under cold marine environment. Some comparison studies were conducted on plain concrete by rapid freeze-thaw cycle test. During the rapid freeze-thaw cycle test, the mass loss and relative elastic modulus were measured regularly at the prescribed conditioning ages. The development of microstructure in concrete was analyzed through scanning electron microscopy (SEM) and X-ray diffraction (XRD). The rapid freeze-thaw cycle test results show that the plain concrete was destroyed severely at 150 freeze-thaw cycles. After 225 freeze-thaw cycles, the mass loss and the relative dynamic modulus of elasticity of GGBFS concrete decrease 1.3% and 26.11%, respectively, that indicates that GGBFS significantly improve the anti-frost performance of concrete; The addition of GGBFS can accelerate the cement hydration reaction, promote more Ca (OH)2 crystals shift to C-S-H gel and help to increase the density of the micro-structure of concrete, which can prevent the formation of micro-cracks and suppress the propagation of cracks and thus effectively improve the durability of concrete. KEY WORDS: GGBFS; freeze-thaw durability; microstructure; scanning electron microscopy; X-ray diffraction.

scholarly journals Mechanical Properties and Micro Structure of Cement Concrete in Freeze-Thaw Environment

2021 ◽  
Vol 233 ◽  
pp. 01011
Author(s):  
Xin jian Lv ◽  
Lei Yu ◽  
Ming ming Chai
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Pore Structure ◽  
Fresh Water ◽  
Pore Diameter ◽  
Dynamic Elastic Modulus ◽  
Freeze Thaw ◽  
Salty Water ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle

In order to find the declay law of mechanical property and the performance difference after salty water and fresh water freeze-thaw cycle, freeze-thaw cycle environments under the salty water and fresh water are simulated. The compressive strength, dynamic elastic modulus and the mass lost are tested. The pore structure parameters are also tested by MIP. Plot the pore diameter distribution curve. The result shows that the compressive strength and dynamic elastic modulus are all decreased. The degree of these two properties decreasing under salty water freeze and thaw recycle is more than the one under fresh water. The parameters of porosity and critical pore diameter become larger. The amount of pores whose diameter is between 100nm and 1000nm increase. The amount of pores whose diameter is under 100nm decrease. The deteriorate degree of pore structure is deeper in salty water than in fresh water.

scholarly journals Numerical Simulation of the Effect of Freeze–Thaw Cycles on the Durability of Concrete in a Salt Frost Environment

Coatings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1198
Author(s):  
Hao Li ◽  
Yuan Zhang ◽  
Haolong Guo
Keyword(s):  
Numerical Simulation ◽  
Bending Moment ◽  
Temperature Curve ◽  
Concrete Durability ◽  
Freezing And Thawing ◽  
Freeze Thaw ◽  
Thaw Cycle ◽  
Freeze Thaw Cycle ◽  
The Impact ◽  
Erosion Environment

In order to improve the accuracy of the analysis of the impact of freeze–thaw cycle on concrete durability in a salt freezing environment, the numerical simulation of the impact of the freeze–thaw cycle on concrete durability in a salt freezing erosion environment is studied in this paper. Firstly, considering the influence of axial force and bending moment on the relationship between bending moment and curvature, a concrete fiber beam column model is established. Then, according to the joint influence of temperature field, stress field and seepage field on concrete in the process of freezing and thawing, the control differential equation of the freezing and thawing cycle is established. The freeze–thaw damage section is divided, the non-uniform distribution of freeze–thaw damage is determined, and the division of the freeze–thaw damage section is completed. According to the linear relationship between freeze–thaw damage degree, relative dynamic elastic modulus, freeze–thaw cycle times and position variables, the durability of concrete is numerically simulated, and the attenuation law of bond strength at different section depths after freeze–thaw is determined. The results show that the temperature curve simulated by the design method is consistent with the actually measured temperature curve, which can better reduce the temperature change of the inner core of the test block during freezing and thawing, and the relative dynamic elastic modulus is in good agreement with the actual value, which can prove that the method in this paper has certain practical application value. It is expected to provide some reference for solving the durability problem of concrete in a salt frost erosion environment and the optimal design of concrete structures.

scholarly journals Dynamic Mechanical Response and Dissipated Energy Analysis of Sandstone under Freeze-Thaw Cycles

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Ke Man ◽  
Zongxu Liu ◽  
Zhifei Song ◽  
Xiaoli Liu
Keyword(s):  
Compressive Strength ◽  
Strain Rate ◽  
Open Pit ◽  
Dissipated Energy ◽  
Freeze Thaw ◽  
Dynamic Mechanical ◽  
Thaw Cycle ◽  
Pore Evolution ◽  
Freeze Thaw Cycle ◽  
Dynamic Compressive Strength

Based on the sandstone from the slope of Baorixile open-pit mining area in Hulunbuir City, Inner Mongolia, the dynamic uniaxial compression test of sandstone with different freeze-thaw cycles has been carried out by Split Hopkinson Pressure Bar test (SHPB). The test results show that the crushing degree of sandstone becomes serious with the freeze-thaw cycle times and strain rate increases. The dynamic compressive strength increases with the raise of strain rate under the same freeze-thaw cycles, while it reduces with the increases of freeze-thaw cycles at the same strain rate. It is found that the 10 freeze-thaw cycles are an obvious inflection point. When it is less than 10 cycles, the dynamic compressive strength of sandstone specimens decreases rapidly, it is more than 10 cycles, and the strength decreases gradually. This is due to that the evolution progress of pores in sandstone is more uniform after a certain number of freeze-thaw cycles. Meantime, the effect of freezing and thawing is mostly restrained by the pore evolution. On the other hand, the dissipated energy required for sandstone failure grows up with the increase of the number of freeze-thaw cycles. It shows that more energy is needed for the engender of pores and fractures in sandstone caused by freeze-thaw cycle. This led to the deterioration of sandstone structural stability and the decrease of dynamic mechanical properties.

Sign in / Sign up

Export Citation Format

Share Document