Optimal Design of Ultra-Low-Power 2.4 GHz LNA for IEEE 802.15.4/Bluetooth Applications

2020 ◽  
Vol 29 (16) ◽  
pp. 2050261
Author(s):  
Sumalya Ghosh ◽  
Bishnu Prasad De ◽  
K. B. Maji ◽  
R. Kar ◽  
D. Mandal ◽  
...  
Keyword(s):  
Optimal Design ◽  
Low Power ◽  
Power Dissipation ◽  
Ieee 802.15.4 ◽  
Low Noise ◽  
Design Parameters ◽  
Cmos Process ◽  
Short Channel ◽  
Ultra Low Power ◽  
Cmos Lna

In this paper, an evolutionary computation-based optimal design of low power, high gain inductive source degenerated CMOS cascode low noise amplifier (LNA) circuit is presented for 2.4[Formula: see text]GHz frequency. The main challenge for the design of radio frequency (RF) LNAs at nanometer range is the thermal noise generated in the short-channel MOSFETs. The short-channel effects (SCEs), such as velocity saturation and channel-length modulation, are considered for the design of CMOS LNA. The evolutionary algorithm taken for this work is Moth-Flame Optimization (MFO) algorithm. MFO is utilized for the optimization of noise figure (NF) while satisfying all the other design performance parameters like gain, matching parameters at input/output, power dissipation, linearity, stability. Optimal values of the sizes of the transistors and other design parameters in designing the LNA circuit are also obtained from the MFO algorithm. The CMOS LNA circuit is designed by using MFO-based optimal design parameters in CADENCE software with a standard 0.18[Formula: see text][Formula: see text]m CMOS process. The designed LNA shows a gain of 15.28[Formula: see text]dB, NF of 0.376[Formula: see text]dB, the power dissipation of 936[Formula: see text][Formula: see text]W and IIP3 of [Formula: see text][Formula: see text]dBm at 2.4[Formula: see text]GHz. The designed LNA achieves better trade-off which results in an FOM of 42.3[Formula: see text]mW[Formula: see text] and may be useful in the receiver module of IEEE 802.15.4 for WLAN applications.

scholarly journals A 219-µW ultra-low power low-noise amplifier for IEEE 802.15.4 based battery powered, portable, wearable IoT applications

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
S. Chrisben Gladson ◽  
Adith Hari Narayana ◽  
V. Thenmozhi ◽  
M. Bhaskar
Keyword(s):  
Low Power ◽  
Ieee 802.15.4 ◽  
Low Voltage ◽  
Low Noise ◽  
Low Noise Amplifier ◽  
Cmos Process ◽  
Process Technology ◽  
Ultra Low Power ◽  
Power Mode ◽  
Noise Amplifier

AbstractDue to the increased processing data rates, which is required in applications such as fifth-generation (5G) wireless networks, the battery power will discharge rapidly. Hence, there is a need for the design of novel circuit topologies to cater the demand of ultra-low voltage and low power operation. In this paper, a low-noise amplifier (LNA) operating at ultra-low voltage is proposed to address the demands of battery-powered communication devices. The LNA dual shunt peaking and has two modes of operation. In low-power mode (Mode-I), the LNA achieves a high gain ($$S21$$ S 21 ) of 18.87 dB, minimum noise figure ($${NF}_{min.}$$ NF m i n . ) of 2.5 dB in the − 3 dB frequency range of 2.3–2.9 GHz, and third-order intercept point (IIP3) of − 7.9dBm when operating at 0.6 V supply. In high-power mode (Mode-II), the achieved gain, NF, and IIP3 are 21.36 dB, 2.3 dB, and 13.78dBm respectively when operating at 1 V supply. The proposed LNA is implemented in UMC 180 nm CMOS process technology with a core area of $$0.40{\mathrm{ mm}}^{2}$$ 0.40 mm 2 and the post-layout validation is performed using Cadence SpectreRF circuit simulator.

scholarly journals An 8.72 µW Low-Noise and Wide Bandwidth FEE Design for High-Throughput Pixel-Strip (PS) Sensors

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1760
Author(s):  
Folla Kamdem Jérôme ◽  
Wembe Tafo Evariste ◽  
Essimbi Zobo Bernard ◽  
Maria Liz Crespo ◽  
Andres Cicuttin ◽  
...  
Keyword(s):  
Low Power ◽  
High Throughput ◽  
Low Noise ◽  
Oxide Semiconductor ◽  
Cmos Process ◽  
High Luminosity ◽  
Gain Bandwidth ◽  
Wide Bandwidth ◽  
Ultra Low Power ◽  
Front End

The front-end electronics (FEE) of the Compact Muon Solenoid (CMS) is needed very low power consumption and higher readout bandwidth to match the low power requirement of its Short Strip application-specific integrated circuits (ASIC) (SSA) and to handle a large number of pileup events in the High-Luminosity Large Hadron Collider (LHC). A low-noise, wide bandwidth, and ultra-low power FEE for the pixel-strip sensor of the CMS has been designed and simulated in a 0.35 µm Complementary Metal Oxide Semiconductor (CMOS) process. The design comprises a Charge Sensitive Amplifier (CSA) and a fast Capacitor-Resistor-Resistor-Capacitor (CR-RC) pulse shaper (PS). A compact structure of the CSA circuit has been analyzed and designed for high throughput purposes. Analytical calculations were performed to achieve at least 998 MHz gain bandwidth, and then overcome pileup issue in the High-Luminosity LHC. The spice simulations prove that the circuit can achieve 88 dB dc-gain while exhibiting up to 1 GHz gain-bandwidth product (GBP). The stability of the design was guaranteed with an 82-degree phase margin while 214 ns optimal shaping time was extracted for low-power purposes. The robustness of the design against radiations was performed and the amplitude resolution of the proposed front-end was controlled at 1.87% FWHM (full width half maximum). The circuit has been designed to handle up to 280 fC input charge pulses with 2 pF maximum sensor capacitance. In good agreement with the analytical calculations, simulations outcomes were validated by post-layout simulations results, which provided a baseline gain of 546.56 mV/MeV and 920.66 mV/MeV, respectively, for the CSA and the shaping module while the ENC (Equivalent Noise Charge) of the device was controlled at 37.6 e− at 0 pF with a noise slope of 16.32 e−/pF. Moreover, the proposed circuit dissipates very low power which is only 8.72 µW from a 3.3 V supply and the compact layout occupied just 0.0205 mm2 die area.

scholarly journals Development of Low-Noise Small-Area 24 GHz CMOS Radar Sensor

2016 ◽  
Vol 2016 ◽  
pp. 1-12
Author(s):  
Min Yoon ◽  
Jee-Youl Ryu
Keyword(s):  
Low Power ◽  
Power Dissipation ◽  
Small Area ◽  
Noise Figure ◽  
Low Noise ◽  
Cmos Process ◽  
Radar Sensor ◽  
Low Power Dissipation ◽  
Chip Size ◽  
24 Ghz

We present a low-noise small-area 24 GHz CMOS radar sensor for automotive collision avoidance. This sensor is based on direct-conversion pulsed-radar architecture. The proposed circuit is implemented using TSMC 0.13 μm RF (radio frequency) CMOS (fT/fmax=120/140 GHz) technology, and it is powered by a 1.5 V supply. This circuit uses transmission lines to reduce total chip size instead of real bulky inductors for input and output impedance matching. The layout techniques for RF are used to reduce parasitic capacitance at the band of 24 GHz. The proposed sensor has low cost and low power dissipation since it is realized using CMOS process. The proposed sensor showed the lowest noise figure of 2.9 dB and the highest conversion gain of 40.2 dB as compared to recently reported research results. It also showed small chip size of 0.56 mm2, low power dissipation of 39.5 mW, and wide operating temperature range of −40 to +125°C.

A LOW-NOISE LOW-POWER FRONT-END AMPLIFIER FOR NEURAL-RECORDING APPLICATIONS

2010 ◽  
Vol 22 (04) ◽  
pp. 301-306 ◽  
Author(s):  
Mohammad Hossein Zarifi ◽  
Javad Frounchi ◽  
Mohammad A. Tinati ◽  
Shahin Farshchi ◽  
Jack W. Judy
Keyword(s):  
Low Power ◽  
Heat Dissipation ◽  
Harmonic Distortion ◽  
Low Noise ◽  
Low Noise Amplifiers ◽  
Cmos Process ◽  
Ultra Low Power ◽  
Fully Differential ◽  
Front End

Monitoring the electrical activities of a large number of neurons in vertebrates' central nervous system in vivo through hundreds of parallel channels without interferring in their natural functions is a neuroscientist's interest. Value of this information in both scientific and clinical contexts, especially in expansion of brain–computer interfaces, is extremely significant. Therefore, low-noise amplifiers are needed with filtering capability on the front end to amplify the desired signals and eliminate direct current baseline shifts. Hence, size and power consumption need to be minimized to reduce trauma and heat dissipation, which can result in tissue damage for human applications and the system needs to be implantable and wireless. The practical solution for developing such systems is system-on-a-chip, based on ultra-low-power mixed-mode and wideband RFIC designs. They, however, impose a number of challenges that may require nontraditional solutions. In this paper, we present a fully differential low-power low-noise preamplifier suitable for recording biological signals, from a few mHz up to 10 kHz. This amplifier has a bandpass filter that is tunable between 10 mHz and 10 kHz, and has been designed and simulated in a standard 90-nm CMOS process. The circuit consumes 10 μW from a 1.2 V supply and provides a gain of 40 dB and an output swing of ±0.5 V with a total harmonic distortion of less than 0.5%. The total input-referred noise level is 4.6 μV integrating the noise over 0.01 Hz to 10 kHz.

scholarly journals A High-Efficiency CMOS Rectifier for RF Using Bulk Biasing Control Circuit

2018 ◽  
Vol 13 (2) ◽  
pp. 1-6
Author(s):  
Tarcisio Oliveira Moraes Junior ◽  
Raimundo Carlos Silvério Freire ◽  
Cleonilson Protásio de Souza
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Power Dissipation ◽  
High Efficiency ◽  
Control Circuit ◽  
Experimental Results ◽  
Cmos Process ◽  
Leakage Currents ◽  
Ultra Low Power ◽  
Rectifier Circuits

In MOSFET-transistor based rectifier circuits, leakage currents occur through both source-bulk and drain-bulk connections of their transistors causing some power dissipation decreasing their efficiency. Such a scenario is more worrying in ultra-low power circuits as those used in energy harvesting. As a solution, in this work it is proposed a control circuit of transistor bulk biasing that switches the bulk bias in an efficient way assuring adequate inversion of the source-bulk and drain-bulk junctions. The rectifier based on the proposed bulk biasing control circuit shows to be a high-efficiency one capable of reducing the leakage currents. To obtain experimental results, the circuit was fabricated in a 130 nm CMOS process and tested on a micromanipulator. The results were compared with other works where it is observed that the efficiency of our proposal reaches up to 72.5% or 5% higher that the best previous one.

scholarly journals A 0.6-µW Chopper Amplifier Using a Noise-Efficient DC Servo Loop and Squeezed-Inverter Stage for Power-Efficient Biopotential Sensing

Sensors ◽  
2020 ◽  
Vol 20 (7) ◽  
pp. 2059
Author(s):  
Xuan Thanh Pham ◽  
Ngoc Tan Nguyen ◽  
Van Truong Nguyen ◽  
Jong-Wook Lee
Keyword(s):  
Low Power ◽  
Power Efficiency ◽  
Low Noise ◽  
Efficiency Factor ◽  
Instrumentation Amplifier ◽  
Cmos Process ◽  
Common Mode ◽  
Ultra Low Power ◽  
Power Efficient ◽  
Servo Loop

To realize an ultra-low-power and low-noise instrumentation amplifier (IA) for neural and biopotential signal sensing, we investigate two design techniques. The first technique uses a noise-efficient DC servo loop (DSL), which has been shown to be a high noise contributor. The proposed approach offers several advantages: (i) both the electrode offset and the input offset are rejected, (ii) a large capacitor is not needed in the DSL, (iii) by removing the charge dividing effect, the input-referred noise (IRN) is reduced, (iv) the noise from the DSL is further reduced by the gain of the first stage and by the transconductance ratio, and (v) the proposed DSL allows interfacing with a squeezed-inverter (SQI) stage. The proposed technique reduces the noise from the DSL to 12.5% of the overall noise. The second technique is to optimize noise performance using an SQI stage. Because the SQI stage is biased at a saturation limit of 2VDSAT, the bias current can be increased to reduce noise while maintaining low power consumption. The challenge of handling the mismatch in the SQI stage is addressed using a shared common-mode feedback (CMFB) loop, which achieves a common-mode rejection ratio (CMRR) of 105 dB. Using the proposed technique, a capacitively-coupled chopper instrumentation amplifier (CCIA) was fabricated using a 0.18-µm CMOS process. The measured result of the CCIA shows a relatively low noise density of 88 nV/rtHz and an integrated noise of 1.5 µVrms. These results correspond to a favorable noise efficiency factor (NEF) of 5.9 and a power efficiency factor (PEF) of 11.4.

An Ultra-low Power Consumption MAC Protocol Complied with IEEE 802.15.4/4e for Wireless Smart Utility Networks

2016 ◽  
Vol 136 (11) ◽  
pp. 1555-1566 ◽  
Author(s):  
Jun Fujiwara ◽  
Hiroshi Harada ◽  
Takuya Kawata ◽  
Kentaro Sakamoto ◽  
Sota Tsuchiya ◽  
...  
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Ieee 802.15.4 ◽  
Mac Protocol ◽  
Low Power Consumption ◽  
Ultra Low Power

scholarly journals An Ultra-Low-Power K-Band 22.2 GHz-to-26.9 GHz Current-Reuse VCO Using Dynamic Back-Gate-Biasing Technique

Electronics ◽  
2021 ◽  
Vol 10 (8) ◽  
pp. 889
Author(s):  
Xiaoying Deng ◽  
Peiqi Tan
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Tuning Range ◽  
Frequency Tuning ◽  
Cmos Process ◽  
Voltage Controlled Oscillator ◽  
Back Gate ◽  
Ultra Low Power ◽  
Current Reuse ◽  
K Band

An ultra-low-power K-band LC-VCO (voltage-controlled oscillator) with a wide tuning range is proposed in this paper. Based on the current-reuse topology, a dynamic back-gate-biasing technique is utilized to reduce power consumption and increase tuning range. With this technique, small dimension cross-coupled pairs are allowed, reducing parasitic capacitors and power consumption. Implemented in SMIC 55 nm 1P7M CMOS process, the proposed VCO achieves a frequency tuning range of 19.1% from 22.2 GHz to 26.9 GHz, consuming only 1.9 mW–2.1 mW from 1.2 V supply and occupying a core area of 0.043 mm2. The phase noise ranges from −107.1 dBC/HZ to −101.9 dBc/Hz at 1 MHz offset over the whole tuning range, while the total harmonic distortion (THD) and output power achieve −40.6 dB and −2.9 dBm, respectively.

scholarly journals A 2.1 GHz, 210 μW, —189 dBc/Hz DCO with Ultra Low Power DCC Scheme

Electronics ◽  
2021 ◽  
Vol 10 (7) ◽  
pp. 805
Author(s):  
Shi Zuo ◽  
Jianzhong Zhao ◽  
Yumei Zhou
Keyword(s):  
Low Power ◽  
Current Efficiency ◽  
Phase Noise ◽  
Duty Cycle ◽  
Semiconductor Manufacturing ◽  
Figure Of Merit ◽  
Room Temperature ◽  
Cmos Process ◽  
Ultra Low Power ◽  
Measured Phase

This article presents a low power digital controlled oscillator (DCO) with an ultra low power duty cycle correction (DCC) scheme. The DCO with the complementary cross-coupled topology uses the controllable tail resistor to improve the tail current efficiency. A robust duty cycle correction (DCC) scheme is introduced to replace self-biased inverters to save power further. The proposed DCO is implemented in a Semiconductor Manufacturing International Corporation (SMIC) 40 nm CMOS process. The measured phase noise at room temperature is −115 dBc/Hz at 1 MHz offset with a dissipation of 210 μμW at an oscillating frequency of 2.12 GHz, and the resulin figure-of-merit is s −189 dBc/Hz.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Sign in / Sign up

Export Citation Format

Share Document