scholarly journals Factors Influencing the Rheological Properties of MRSP Based on the Orthogonal Experimental Design and the Impact Energy Test

2019 ◽  
Vol 2019 ◽  
pp. 1-11 ◽  
Author(s):  
Bing Liu ◽  
Chengbin Du ◽  
Yankai Fu
Keyword(s):  
Impact Energy ◽  
Influence Factors ◽  
Shear Thickening ◽  
Orthogonal Experimental Design ◽  
Orthogonal Experiments ◽  
Relative Shear ◽  
Rate Of Increase ◽  
Magnetorheological Effect ◽  
Influence Degree ◽  
The Impact

In the preparation process of magnetorheological silly putty (MRSP), the influence factors of the relative shear thickening effect (RSE) and relative magnetorheological effect (RME) were studied by orthogonal experiments as well as range and variance analyses. The influence degree of each factor was also evaluated. The results showed that the viscosity of polydimethylsiloxane (PDMS) and the mass fraction of carbonyl iron powder (CIP) had a significant influence on the RSE and RME, respectively. With an increasing PDMS viscosity, the RSE of the silicon-boron copolymer matrix first increased and then decreased, while the RME of MRSP decreased gradually. In addition, the shear thickening mechanism of MRSP was explored by the molecular chain motion. Finally, the impact energy with different samples was tested, and it is demonstrated that with the increasing cross section, the impact energy of the sample increases gradually, but the rate of increase becomes smaller.

scholarly journals Functionalization of silica particles to tune the impact resistance of shear thickening fluid treated aramid fabrics

RSC Advances ◽  
2017 ◽  
Vol 7 (78) ◽  
pp. 49787-49794 ◽  
Author(s):  
K. Talreja ◽  
I. Chauhan ◽  
A. Ghosh ◽  
A. Majumdar ◽  
B. S. Butola
Keyword(s):  
Energy Absorption ◽  
Impact Energy ◽  
Impact Resistance ◽  
Shear Thickening ◽  
Silica Particles ◽  
Modified Silica ◽  
Shear Thickening Fluid ◽  
Aramid Fabrics ◽  
And Control ◽  
The Impact

Kevlar fabrics treated with MTMS modified silica based STF showed better impact energy absorption as compared to APTES modified and control silica based STF treated fabrics, attributed to changes in interactions between fabrics and silica particles.

Effects of shear-thickening polymer on force attenuation capacities in hip protectors

2021 ◽  
pp. 095440622110469
Author(s):  
Haeun Yum ◽  
Hamin Lim ◽  
Dahae Min ◽  
Chani Kwon ◽  
Jiin Seo ◽  
...  
Keyword(s):  
Polyurethane Foam ◽  
Impact Energy ◽  
Shear Thickening ◽  
Neck Region ◽  
Free Fall ◽  
Mechanical Tests ◽  
Energy Conditions ◽  
Hip Protector ◽  
Hip Protectors ◽  
The Impact

Many elderly people use hip protectors to prevent hip fractures from sideways falls. These hip protectors absorb or shunt away the energy applied to the greater trochanter. Herein, shear-thickening polymer (STP)-based hip protectors composed of STP and polyurethane foam are studied. The purpose of this study was to identify the main factor that reduces the impact force directly applied to the femoral neck region and to determine the optimal thickness of STP in hip protectors. Seven hip protectors of different thicknesses were prepared, and two sets of free-fall mechanical tests with a low impact energy of 25.1 J and moderate impact energy of 44.1 J were conducted for each hip protector. When the thickness of STP exceeded 8 mm, the resultant peak force tended to plateau under both impact conditions, and the force attenuation capacity decreased even under low impact energy conditions. Thus, a hip protector with a 6 mm or 8 mm STP and 5 mm foam was recommended. The STP was the key factor affecting force attenuation capacity, not the polyurethane foam. However, the foam also played an important role in helping the STP function and improving compliance for users.

scholarly journals Research on Impact Performance of Hydraulic Rock Drill with Floating Characteristics of Double Damping System

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Yelin Li ◽  
Zeng Bin ◽  
Yi Tu
Keyword(s):  
Experimental Data ◽  
Impact Energy ◽  
Influence Factors ◽  
Characteristic Parameters ◽  
Impact Performance ◽  
Experimental Scheme ◽  
Rock Drill ◽  
Feed Force ◽  
The Impact ◽  
The Relationship

As a technological innovation of high-power hydraulic rock drill, double damping system has a very important effect on impact performance. The double damping system is a floating mechanism. The characteristics of the floating mechanism have an important influence on the impact energy, frequency, and power of the hydraulic rock drill. Based on orifice throttling theory, the static equilibrium position of a damping piston was calculated, and the characteristic parameters of the double damping system were summarized as damping flow (Qd) and feed force (Fd). According to the characterization parameters of the double damping system, an experimental scheme of the floating characteristics of the double damping system was designed, and the combined experimental data of Qd and Fd were obtained. The 40 groups of experimental data were extracted, and the relationship between the combination (Qd, Fd) and impact energy and frequency and power were analyzed. The combination (Qd, Fd) with maximum and minimum power was selected to analyze the motion law of an impact piston. The maximum drilling power was obtained at the combination (Qd = 8 L·min−1, Fd = 16.25 kN). The influence factors of the double damping system on impact performance were summarized, and the characteristics of the double damping system under optimal impact performance were obtained.

scholarly journals Viscous-like forces control the impact response of shear-thickening dense suspensions

2021 ◽  
Vol 923 ◽  
Author(s):  
Marc-Andre Brassard ◽  
Neil Causley ◽  
Nasser Krizou ◽  
Joshua A. Dijksman ◽  
Abram. H. Clark
Keyword(s):  
Shear Thickening ◽  
Impact Response ◽  
Dense Suspensions ◽  
The Impact

Abstract

scholarly journals Analysis of surface deformation and driving forces in Lanzhou

2020 ◽  
Vol 12 (1) ◽  
pp. 1127-1145
Author(s):  
Wenhui Wang ◽  
Yi He ◽  
Lifeng Zhang ◽  
Youdong Chen ◽  
Lisha Qiu ◽  
...  
Keyword(s):  
International Development ◽  
Surface Deformation ◽  
Driving Forces ◽  
Influence Factors ◽  
Chinese Government ◽  
Single Factor ◽  
Rapid Urbanization ◽  
Temporal Characteristics ◽  
Maximum Deformation ◽  
Rate Of Increase

AbstractSurface deformation has become an important factor affecting urban development. Lanzhou is an important location in the Belt and Road Initiative, an international development policy implemented by the Chinese government. Because of rapid urbanization in Lanzhou, surface deformation occurs easily. However, the spatial-temporal characteristics of surface deformation and the interaction of driving forces behind surface deformation in Lanzhou are unclear. This paper uses small baseline subset InSAR (SBAS-InSAR) technology to obtain the spatial-temporal characteristics of surface deformation in Lanzhou based on 32 Sentinel-1A data from March 2015 to January 2017. We further employ a geographical detector (geo-detector) to analyze the driving forces (single-factor effects and multifactor interactions) of surface deformation. The results show that the central urban area of Lanzhou was stable, while there was surface deformation around Nanhuan road, Dongfanghong Square, Jiuzhou, Country Garden, Dachaiping, Yujiaping, Lanzhou North Freight Yard, and Liuquan Town. The maximum deformation rate was −26.50 mm year−1, and the maximum rate of increase was 9.80 mm year−1. The influence factors of surface deformation in Lanzhou was a complex superposition relationship among various influencing factors, not a result of the single factor. The interaction between the built-up area and land cover types was the most important factor behind surface deformation in Lanzhou. This paper provides the reference data and scientific foundation for disaster prevention in Lanzhou.

Response and failure modes of biaxial warp-knitted flexible composite subject to low-velocity impact

2021 ◽  
pp. 152808372110154
Author(s):  
Ziyu Zhao ◽  
Tianming Liu ◽  
Pibo Ma
Keyword(s):  
Impact Energy ◽  
Linear Density ◽  
Failure Modes ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Minor Effect ◽  
Low Velocity ◽  
Velocity Impact ◽  
Flexible Composites ◽  
The Impact

In this paper, biaxial warp-knitted fabrics were produced with different high tenacity polyester linear density and inserted yarns density. The low-velocity impact property of flexible composites made of polyurethane as matrix and biaxial warp-knitted fabric as reinforcement has been investigated. The effect of impactor shape and initial impact energy on the impact response of flexible composite is tested. The results show that the initial impact energy have minor effect on the impact response of the biaxial warp-knitted flexible composites. The impact resistance of flexible composite specimen increases with the increase of high tenacity polyester linear density and inserted yarns density. The damage morphology of flexible composite materials is completely different under different impactor shapes. The findings have theoretical and practical significance for the applications of biaxial warp-knitted flexible composite.

scholarly journals Impact resistance of steel materials to ballistic ejecta and shelter development using steel deck plates

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Hiroyuki Yamada ◽  
Kohei Tateyama ◽  
Shino Naruke ◽  
Hisashi Sasaki ◽  
Shinichi Torigata ◽  
...  
Keyword(s):  
Impact Energy ◽  
Impact Test ◽  
Impact Resistance ◽  
Protective Layer ◽  
High Strength ◽  
Steel Plates ◽  
Corrugated Plates ◽  
Shelter Construction ◽  
The Impact ◽  
Ballistic Ejecta

AbstractThe destruction caused by ballistic ejecta from the phreatic eruptions of Mt. Ontake in 2014 and Mt. Kusatsu-Shirane (Mt. Moto-Shirane) in 2018 in Japan, which resulted in numerous casualties, highlighted the need for better evacuation facilities. In response, some mountain huts were reinforced with aramid fabric to convert them into shelters. However, a number of decisions must be made when working to increase the number of shelters, which depend on the location where they are to be built. In this study, we propose a method of using high-strength steel to reinforce wooden buildings for use as shelters. More specifically, assuming that ballistic ejecta has an impact energy of 9 kJ or more, as in previous studies, we developed a method that utilizes SUS304 and SS400 unprocessed steel plates based on existing impact test data. We found that SUS304 is particularly suitable for use as a reinforcing material because it has excellent impact energy absorption characteristics due to its high ductility as well as excellent corrosion resistance. With the aim of increasing the structural strength of steel shelters, we also conducted an impact test on a shelter fabricated from SS400 deck plates (i.e., steel with improved flexural strength provided by work-hardened trapezoidal corrugated plates). The results show that the shelter could withstand impact with an energy of 13.5 kJ (2.66 kg of simulated ballistic ejecta at 101 m/s on impact). In addition, from the result of the impact test using the roof-simulating structure, it was confirmed the impact absorption energy is further increased when artificial pumice as an additional protective layer is installed on this structure. Observations of the shelter after the impact test show that there is still some allowance for deformation caused by projectile impact, which means that the proposed steel shelter holds promise, not only structurally, but also from the aspects of transportation and assembly. Hence, the usefulness of shelters that use steel was shown experimentally. However, shelter construction should be suitable for the target environment.

scholarly journals Braided composite stent for peripheral vascular applications

2020 ◽  
Vol 9 (1) ◽  
pp. 1137-1146
Author(s):  
Qingli Zheng ◽  
Pengfei Dong ◽  
Zhiqiang Li ◽  
Ying Lv ◽  
Meiwen An ◽  
...  
Keyword(s):  
Computational Models ◽  
Surface Coverage ◽  
Mechanical Performance ◽  
Wire Diameter ◽  
Orthogonal Experimental Design ◽  
Braided Composite ◽  
Nitinol Wire ◽  
Radial Strength ◽  
Braiding Angle ◽  
The Impact

AbstractBraided composite stent (BCS), woven with nitinol wires and polyethylene terephthalate (PET) strips, provides a hybrid design of stent. The mechanical performance of this novel stent has not been fully investigated yet. In this work, the influence of five main design factors (number of nitinol wires, braiding angle, diameter of nitinol wire, thickness and stiffness of the PET strip) on the surface coverage, radial strength, and flexibility of the BCS were systematically studied using computational models. The orthogonal experimental design was adopted to quantitatively analyze the sensitivity of multiple factors using the minimal number of study cases. Results have shown that the nitinol wire diameter and the braiding angle are two most important factors determining the mechanical performance of the BCS. A larger nitinol wire diameter led to a larger radial strength and less flexibility of the BCS. A larger braiding angle could provide a larger radial strength and better flexibility. In addition, the impact of the braiding angle decreased when the stent underwent a large deformation. At the same time, the impact of the PET strips increased due to the interaction with nitinol wires. Moreover, the number of PET strips played an important role in the surface coverage. This study could help understand the mechanical performance of BCS stent and provides guidance on the optimal design of the stent targeting less complications.

scholarly journals Microstructure and Mechanical Properties of Heat-Affected Zone of Repeated Welding AISI 304N Austenitic Stainless Steel by Gleeble Simulator

Metals ◽  
2018 ◽  
Vol 8 (10) ◽  
pp. 773
Author(s):  
Y.H. Guo ◽  
Li Lin ◽  
Donghui Zhang ◽  
Lili Liu ◽  
M.K. Lei
Keyword(s):  
Mechanical Properties ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Impact Energy ◽  
Heat Affected Zone ◽  
Ferrite Content ◽  
Equipment Safety ◽  
Microstructure And Mechanical Properties ◽  
Δ Ferrite ◽  
The Impact

Heat-affected zone (HAZ) of welding joints critical to the equipment safety service are commonly repeatedly welded in industries. Thus, the effects of repeated welding up to six times on the microstructure and mechanical properties of HAZ for AISI 304N austenitic stainless steel specimens were investigated by a Gleeble simulator. The temperature field of HAZ was measured by in situ thermocouples. The as-welded and one to five times repeated welding were assigned as-welded (AW) and repeated welding 1–5 times (RW1–RW5), respectively. The austenitic matrices with the δ-ferrite were observed in all specimens by the metallography. The δ-ferrite content was also determined using magnetic and metallography methods. The δ-ferrite had a lathy structure with a content of 0.69–3.13 vol.%. The austenitic grains were equiaxial with an average size of 41.4–47.3 μm. The ultimate tensile strength (UTS) and yield strength (YS) mainly depended on the δ-ferrite content; otherwise, the impact energy mainly depended on both the austenitic grain size and the δ-ferrite content. The UTS of the RW1–RW3 specimens was above 550 MPa following the American Society of Mechanical Engineers (ASME) standard. The impact energy of all specimens was higher than that in ASME standard at about 56 J. The repeated welding up to three times could still meet the requirements for strength and toughness of welding specifications.

Sign in / Sign up

Export Citation Format

Share Document