scholarly journals Saliva and Serum Protein Adsorption on Chemically Modified Silica Surfaces

2021 ◽  
pp. 002203452110222
Author(s):  
J. Lehnfeld ◽  
Y. Dukashin ◽  
J. Mark ◽  
G.D. White ◽  
S. Wu ◽  
...  
Keyword(s):  
Protein Adsorption ◽  
Binding Capacity ◽  
High Surface ◽  
Contact Angles ◽  
Adsorption Behavior ◽  
Protein Layer ◽  
Water Contact ◽  
Silica Surfaces ◽  
Chemically Modified ◽  
Biomaterial Surface

Biomaterials, once inserted in the oral cavity, become immediately covered by a layer of adsorbed proteins that consists mostly of salivary proteins but also of plasma proteins if the biomaterial is placed close to the gingival margin or if it becomes implanted into tissue and bone. It is often this protein layer, rather than the pristine biomaterial surface, that is subsequently encountered by colonizing bacteria or attaching tissue cells. Thus, to study this important initial protein adsorption from human saliva and serum and how it might be influenced through chemical modification of the biomaterial surface, we have measured the amount of protein adsorbed and analyzed the composition of the adsorbed protein layer using gel electrophoresis and western blotting. Here, we have developed an in vitro model system based on silica surfaces, chemically modified with 7 silane-based self-assembled monolayers that span a broad range of physicochemical properties, from hydrophilic to hydrophobic surfaces (water contact angles from 15° to 115°), low to high surface free energy (12 to 57 mN/m), and negative to positive surface charge (zeta potentials from –120 to +40 mV at physiologic pH). We found that the chemical surface functionalities exerted a substantial effect on the total amounts of proteins adsorbed; however, no linear correlation of the adsorbed amounts with the physicochemical surface parameters was observed. Only the adsorption behavior of a few singular protein components, from which physicochemical data are available, seems to follow physicochemical expectations. Examples are albumin in serum and lysozyme in saliva; in both, adsorption was favored on countercharged surfaces. We conclude from these findings that in complex biofluids such as saliva and serum, adsorption behavior is dominated by the overall protein-binding capacity of the surface rather than by specific physicochemical interactions of single protein entities with the surface.

scholarly journals Impact of Air Exposure Time on the Water Contact Angles of Daily Disposable Silicone Hydrogels

2019 ◽  
Vol 20 (6) ◽  
pp. 1313 ◽  
Author(s):  
Petar Eftimov ◽  
Norihiko Yokoi ◽  
Nikola Peev ◽  
Georgi Georgiev
Keyword(s):  
Surface Coating ◽  
Sessile Drop ◽  
High Surface ◽  
Tear Film ◽  
Contact Angles ◽  
Water Contact ◽  
Air Exposure ◽  
Film Stability ◽  
Silicone Hydrogel ◽  
Silicone Hydrogels

The wettability of silicone hydrogel (SiHy) contact lens (CLs) is crucial for the pre-lens tear film stability throughout the day. Therefore, sessile drop and captive bubble setups were used to study the advancing and receding water contact angles (CA) of four SiHy materials: narafilcon A (TE), senofilcon A (AOD), stenfilcon A (MD), and delefilcon A (DT). TE and AOD have 48% and 38% water content, respectively, and no surface coating. MD (54% water) implements “smart chemistry” with just 4.4% bulk silicone content, while DT has >80% water at its surface. These SiHy were subjected to continuous blink-like air exposure (10 s)/rehydration (1s) cycles for 0, 1, 2, 3, 4, 6, 8, 10, 12, 14, and 16 h. The advancing CA, which measures the rehydration propensity of the CL surface, proved to be the most sensitive parameter to discriminate between the samples. The order of performance for the entire time scale was DT > MD >> AOD ≥ TE. The extended desiccation/rehydration cycling increased the differences between the CA of DT and MD compared to AOD and TE. This suggests that the low Si surface content and the high surface hydration are major determinants of SiHy wettability.

scholarly journals Experimental approach towards the water contact angle value on the biomaterial alloy Ti6Al4V

2015 ◽  
Vol 70 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Margarita Hierro-Oliva ◽  
Amparo Maria Gallardo-Moreno ◽  
Abraham Rodríguez-Cano ◽  
Jose Morales Bruque ◽  
Maria Luisa González-Martín
Keyword(s):  
Contact Angle ◽  
Water Contact Angle ◽  
Contact Angles ◽  
Ti6al4v Alloy ◽  
Surrounding Water ◽  
Water Contact ◽  
Large Dispersion ◽  
Biomaterial Surface ◽  
Average Water ◽  
Orthopedic Applications

AbstractIn the biomedical field, water contact angle is a useful gauge to follow how a biomaterial surface would interact with the surrounding water-like physiological environment. Ti6Al4V alloy is widely used in orthopedic applications. Nevertheless, the values of its water contact angle reported in the literature show a large dispersion, from 40° up 80°. However, in addition to the expected dependence of the surface wettability on preliminary treatments, the values of the water contact angle on the pristine Ti6Al4V alloy suffers from an important variability and lack of reproducibility. The present research pays attention to this difficulty and proposes a simple experimental procedure to ensure adequate contact angle reproducibility. Controlled passivation growth in mild underwater conditions of freshly polished disks, followed by ultrasonic washing, avoiding the rubbing of the surface, gives average water contact angles of 80° with very low standard deviations also among samples from the same batch.

scholarly journals Siloxane-Starch-Based Hydrophobic Coating for Multiple Recyclable Cellulosic Materials

Materials ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 4977
Author(s):  
Tomasz Ganicz ◽  
Krystyna Rózga-Wijas
Keyword(s):  
High Surface ◽  
Barrier Properties ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Recycling Process ◽  
Water Contact ◽  
Cellulosic Materials ◽  
Circulating Water ◽  
Hydrophobic Coating ◽  
Aqueous Mixture

The results of the application of a new hydrophobization agent based on a triethoxymethylsilane and standard starch aqueous mixture for mass-produced cellulosic materials—printing paper, paperboard, and sack paper—have been evaluated to examine whether such a mixture can be used in industrial practice. The application of this agent on laboratory sheets prepared in a repetitive recycling process was performed to investigate its influence on the formation and properties of the products, as well as the contamination of circulating water. Measurements of the water contact angle, Cobb tests, and water penetration dynamics (PDA) were performed to test the barrier properties of the resulting materials. The effects of the applied coatings and recycling process on the paper’s tensile strength, tear index, roughness, air permeance, and ISO brightness were studied. Studies have proven that this formulation imparts relatively high surface hydrophobicity to all materials tested (contact angles above 100°) and a significant improvement in barrier properties while maintaining good mechanical and optical performance. The agent also does not interfere with the pulping and re-forming processes during recycling and increases circulation water contamination to an acceptable degree. Attenuated total reflectance Fourier-transform infrared (FT-IR) spectra of the paper samples revealed the presence of a polysiloxane network on the surface.

Porous Fluorinated Graphene and ZIF-67 Composites with Hydrophobic-Oleophilic Properties Towards Oil and Organic Solvent Sorption

2020 ◽  
Vol 20 (5) ◽  
pp. 2930-2938 ◽  
Author(s):  
R. Yogapriya ◽  
K. K. R. Datta
Keyword(s):  
Oil Recovery ◽  
High Performance ◽  
High Surface ◽  
High Surface Area ◽  
Contact Angles ◽  
Future Research ◽  
Water Contact ◽  
Water Separation ◽  
Oil Water ◽  
Fluorinated Graphene

Designing hydrophobic-oleophilic sorbent materials have gained significant interest owing to its potential applications in self-cleaning technologies particularly oil-water separation. The crucial factors remain in the future research of designing materials with high performance hydrophobicoleophilic properties include facile synthesis, low-density, reusability and ecofriendly. Herein, we develop porous hydrophobic-oleophilic nanoarchitecture based on 2D fluorinated graphene (FG) supported cobalt based zeolite imidazole framework (ZIF-67) by solution assisted self-assembly. The key features of the work include in-situ growth and assembly of ZIF-67 over functionalized fluorinated graphene f-FG macrostructures, high surface area and solution processable and spray coated sponge. Methodical characterization of f-FG@ZIF-67 composites, followed by measuring water contact angles by contact angle goniometer. Furthermore, the assessment of sorption capacity of oils and organics followed by oil recovery from oil-water mixtures, excellent chemical and physical stabilities were displayed by these hydrophobic-oleophilic composites.

Osteogenic differentiation of mesenchymal stem cells modulated by a chemically modified super-hydrophilic titanium implant surface

2018 ◽  
Vol 33 (2) ◽  
pp. 205-215 ◽  
Author(s):  
Yong-Su Kwon ◽  
Jin-Woo Park
Keyword(s):  
Stem Cells ◽  
Mesenchymal Stem Cells ◽  
Osteogenic Differentiation ◽  
Bone Healing ◽  
Titanium Implant ◽  
Contact Angles ◽  
Mouse Bone Marrow ◽  
Implant Surface ◽  
Water Contact ◽  
Chemically Modified

This study investigated the osteogenic functionality of multipotent mesenchymal stem cells (MSCs) modulated by a chemically modified super-hydrophilic titanium (Ti) bone implant surface to elucidate the biological mechanism underlying the bone healing capacity of this modified Ti surface. A microstructured Ti surface incorporating bioactive ions (in this study, phosphate (P) ions) was prepared by wet chemical treatment. The results showed that the hydrothermally obtained crystalline P-incorporated Ti surface (P surface) displayed long-term super-hydrophilicity (water contact angles <5°) during a 36-week observation period. The hydrophilic P surface enhanced early cellular functions and osteogenic differentiation of multipotent MSCs derived from mouse bone marrow and human adipose tissue. The expression of critical integrins affecting subsequent osteoblast function and osteoblast phenotype genes was notably upregulated in multipotent MSCs grown on the P surface compared with the commercially available grit-blasted microrough clinical oral implant surface. The P surface supported better cell spreading, focal adhesion and ALP activity of MSCs. These results indicate that a super-hydrophilic P-incorporated Ti surface accelerates implant bone healing by enhancing the early osteogenesis functions of multipotent MSCs.

scholarly journals The Effect of Hydroxyl on the Superhydrophobicity of Dodecyl Methacrylate (LMA) Coated Fabrics through Simple Dipping-Plasma Crosslinked Method

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1263
Author(s):  
Liyun Xu ◽  
Yu Zhang ◽  
Ying Guo ◽  
Ruiyun Zhang ◽  
Jianjun Shi ◽  
...  
Keyword(s):  
Thermoplastic Polyurethane ◽  
Hydrophobic Effect ◽  
Surface Hydrophobicity ◽  
Contact Angles ◽  
Binding Property ◽  
Interesting Phenomenon ◽  
Water Contact ◽  
Capacitively Coupled ◽  
Pet Fabric ◽  
Dodecyl Methacrylate

In order to obtain stable superhydrophobicity, suitable hydrophobic treatment agents should be selected according to different material properties. In this paper, cotton and poly(ethylene terephthalate) (PET) fabrics were respectively coated with dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of the treated cotton and polyester fabrics are also discussed. An interesting phenomenon happened, whereby the LMA-coated cotton fabric (Cotton-g-LMA) had better water repelling and mechanical durability properties than LMA-coated PET fabric (PET-g-LMA), and LMA-coated hydroxyl-grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG & LMA) had a similar performance to cotton fabrics. The water contact angles of Cotton-g-LMA, PET-g-LMA and PET-g-PEG & LMA were 156°, 153° and 155°, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding water contact angles decreased to 145°, 88°, 134° and 146°, 127° and 143°, respectively. Additionally, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics all exhibited the same properties as the PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively, without changing the wearing comfort.

scholarly journals Polypropylene/Lignin/POSS Nanocomposites: Thermal and Wettability Properties, Application in Water Remediation

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3950
Author(s):  
Abeer Alassod ◽  
Syed Rashedul Islam ◽  
Mina Shahriari Khalaji ◽  
Rogers Tusiime ◽  
Wanzhen Huang ◽  
...  
Keyword(s):  
Organic Liquid ◽  
Contact Angles ◽  
Water Remediation ◽  
Scanning Calorimetry ◽  
Water Contact ◽  
Thermally Induced ◽  
Dsc Measurements ◽  
Infrared Measurement ◽  
Oligomeric Silsesquioxane ◽  
Tga And Dsc

Compositing is an interesting strategy that has always been employed to introduce or enhance desired functionalities in material systems. In this paper, sponges containing polypropylene, lignin, and octavinyl-polyhedral oligomeric silsesquioxane (OV-POSS) were successfully prepared via an easy and elegant strategy called thermally induced phase separation (TIPS). To fully explore the behaviour of different components of prepared sponges, properties were characterized by a thermogravimetric analyser (TGA), differential scanning calorimetry (DSC), Fourier transform infrared measurement (FTIR), and scanning electron microscopy (SEM). Furthermore, wettability properties toward an organic liquid and oil were investigated. The FTIR analysis confirmed the chemical modification of the components. TGA and DSC measurements revealed thermal stability was much better with an increase in OV-POSS content. OV-POSS modified sponges exhibited ultra-hydrophobicity and high oleophilicity with water contact angles of more than 125°. The SEM revealed that POSS molecules acted as a support for reduced surface roughness. Moreover, OV-POSS-based blend sponges showed higher sorption capacities compared with other blend sponges without OV-POSS. The new blend sponges demonstrated a potential for use as sorbent engineering materials in water remediation.

scholarly journals Physico-Chemical Characterization and Antimicrobial Properties of Hybrid Film Based on Saponite and Phloxine B

Molecules ◽  
2021 ◽  
Vol 26 (2) ◽  
pp. 325
Author(s):  
Nitin Chandra teja Dadi ◽  
Matúš Dohál ◽  
Veronika Medvecká ◽  
Juraj Bujdák ◽  
Kamila Koči ◽  
...  
Keyword(s):  
Hybrid Film ◽  
Antimicrobial Properties ◽  
Chemical Characterization ◽  
Layered Silicate ◽  
Contact Angles ◽  
Exchange Capacity ◽  
Resistant Bacteria ◽  
Hybrid Films ◽  
Water Contact ◽  
Physico Chemical

This research was aimed at the preparation of a hybrid film based on a layered silicate saponite (Sap) with the immobilized photosensitizer phloxine B (PhB). Sap was selected because of its high cation exchange capacity, ability to exfoliate into nanolayers, and to modify different surfaces. The X-ray diffraction of the films confirmed the intercalation of both the surfactant and PhB molecules in the Sap film. The photosensitizer retained its photoactivity in the hybrid films, as shown by fluorescence spectra measurements. The water contact angles and the measurement of surface free energy demonstrated the hydrophilic nature of the hybrid films. Antimicrobial effectiveness, assessed by the photodynamic inactivation on hybrid films, was tested against a standard strain and against methicillin-resistant bacteria of Staphylococcus aureus (MRSA). One group of samples was irradiated (green LED light; 2.5 h) and compared to nonirradiated ones. S. aureus strains manifested a reduction in growth from 1-log10 to over 3-log10 compared to the control samples with Sap only, and defects in S. aureus cells were proven by scanning electron microscopy. The results proved the optimal photo-physical properties and anti-MRSA potential of this newly designed hybrid system that reflects recent progress in the modification of surfaces for various medical applications.

scholarly journals Bonding of Selected Hardwoods with PVAc Adhesive

2020 ◽  
Vol 11 (1) ◽  
pp. 67
Author(s):  
Ján Iždinský ◽  
Ladislav Reinprecht ◽  
Ján Sedliačik ◽  
Jozef Kúdela ◽  
Viera Kučerová
Keyword(s):  
Adhesion Strength ◽  
Cold Water ◽  
Ph Value ◽  
Water Extract ◽  
Solid Wood ◽  
Contact Angles ◽  
Water Contact ◽  
Ph Values ◽  
Positive Tendency ◽  
The Impact

The bonding of wood with assembly adhesives is crucial for manufacturing wood composites, such as solid wood panels, glulam, furniture parts, and sport and musical instruments. This work investigates 13 hardwoods—bangkirai, beech, black locust, bubinga, ipé, iroko, maçaranduba, meranti, oak, palisander, sapelli, wengé and zebrano—and analyzes the impact of their selected structural and physical characteristics (e.g., the density, cold water extract, pH value, roughness, and wettability) on the adhesion strength with the polyvinyl acetate (PVAc) adhesive Multibond SK8. The adhesion strength of the bonded hardwoods, determined by the standard EN 205, ranged in the dry state from 9.5 MPa to 17.2 MPa, from 0.6 MPa to 2.6 MPa in the wet state, and from 8.5 MPa to 19.2 MPa in the reconditioned state. The adhesion strength in the dry state of the bonded hardwoods was not influenced by their cold water extracts, pH values, or roughness parallel with the grain. On the contrary, the adhesion strength was significantly with positive tendency influenced by their higher densities, lower roughness parameters perpendicular to the grain, and lower water contact angles.

Sign in / Sign up

Export Citation Format

Share Document