The effect of three-lobed bearing shapes in floating-ring bearings on the nonlinear oscillations of high-speed rotors

2019 ◽  
Vol 234 (5) ◽  
pp. 751-769 ◽  
Author(s):  
Congcong Zhang ◽  
Yongliang Wang ◽  
Rixiu Men ◽  
Hong He ◽  
Wei Chen
Keyword(s):  
High Speed ◽  
Nonlinear Oscillations ◽  
Low Cost ◽  
Simulation Method ◽  
Attractive Alternative ◽  
Moderate Increase ◽  
Oil Whirl ◽  
Transient Simulations ◽  
Run Up ◽  
Novel Concept

Floating-ring bearings are widely used in automotive turbocharger machinery because of their robustness, low cost and their suitability under extreme rotation speeds. This type of bearings, however, can become a source of noise due to oil whirl/whip instability. The stabilizing effect of lobed bearing shape is known in the literature, which encourages the researchers to substitute plain cylindrical full floating bearings with lobed geometries in their outer and inner clearances to prevent the rotor-bearing system from developing oil whirl/whip instability or to reduce its amplitude of response when oil whirl/whip instability takes place. In this study, a novel concept of a floating-ring bearing with three-lobed clearances in its inner and outer films is modelled. In order to perform transient simulations, a very time-efficient approximate solution for the Reynolds equation to the geometry of three-lobed bearings is presented. Using the run-up simulation method, the nonlinear dynamic behaviours of a real turbocharger rotor supported by the novel concept of three-lobed floating-ring bearings are systematically investigated. The newly obtained results show that the sub-synchronous vibrations can be thoroughly suppressed with high preload factor at the cost of a moderate increase in the synchronous vibrations. Hence, the three-lobed floating-ring bearings design is an attractive alternative to plain cylindrical floating-ring bearings for automotive turbocharger applications.

Dynamic behaviors of a high-speed turbocharger rotor on elliptical floating-ring bearings

2019 ◽  
Vol 233 (12) ◽  
pp. 1785-1799 ◽  
Author(s):  
Congcong Zhang ◽  
Yongliang Wang ◽  
Rixiu Men ◽  
Hong He ◽  
Wei Chen
Keyword(s):  
High Speed ◽  
Reynolds Equation ◽  
Low Cost ◽  
Dynamic Behaviors ◽  
Oil Whirl ◽  
Excited Vibration ◽  
Dynamic Performances ◽  
Simulation Results ◽  
Bearing Design ◽  
Run Up

Floating-ring bearings are commonly used in automotive turbocharger applications due to their low cost and their suitability under extreme rotation speeds. This type of bearings, however, can become a source of noise due to oil whirl-induced sub-synchronous vibrations. The scope of this paper is to examine whether the concept of a floating-ring bearing with an elliptical clearance might be a solution to suppress sub-synchronous vibrations. A very time-efficient approximate solution for the Reynolds equation to the geometry of elliptical bearings is presented. The nonlinear dynamic behaviors of a turbocharger rotor supported by two concepts of elliptical floating-ring bearings are systematically investigated using run-up simulations. For the first concept of elliptical floating-ring bearings i.e. the outer bearing of the floating-ring bearing changed in the form of elliptical pattern (see Figure 1(b) in the article), some studies have pointed out that its steady-state and dynamic performances are superior to plain cylindrical floating-ring bearings but, the nonlinear run-up simulation results shown that this type of elliptical floating-ring bearings is not conducive to reduce the self-excited vibration levels. However, for the second type of elliptical floating-ring bearings i.e. both the inner and outer films of the floating-ring bearing changed in the form of elliptical pattern (see Figure 1(c) in the article), it is shown that the sub-synchronous vibrations have been considerably suppressed. Hence, the second noncircular floating-ring bearing design is an attractive measure to suppress self-excited vibrations.[Figure: see text]

Confocal Fluorescence Microscopy with CCD Sensors Speed by Parallelization, Low Cost by Using More Electronics

2000 ◽  
Vol 6 (S2) ◽  
pp. 814-815
Author(s):  
Rudolf E. Großkopf
Keyword(s):  
High Speed ◽  
Low Cost ◽  
Confocal Imaging ◽  
The Novel ◽  
Optical Scanning ◽  
Semiconductor Chip ◽  
Confocal Fluorescence ◽  
Mechanical Scanning ◽  
Low Costs ◽  
Novel Concept

CCD sensors are able to image a few megapixels within one frame. The image is scanned electronically within the semiconductor chip (instead of mechanical-optical scanning with moving mirrors, Nipkow discs or acousto-optical devices). Through parallelization. the novel concept yields speed at an unprecedented degree for confocal imaging Routine applications requiring high speed and low costs will profit from this principle. Thus, confocal imaging technology will take the same path television technology has taken—from mechanical scanning to the broadest possible application of electronicsIn order to go this way, a pinhole matrix is used on the illumination side. It has as many pinholes and the same pitch as the pitch and number of pixels of the CCD (Figure 1). In front of the receiver, a second pinhole matrix with the same pitch and number of pinholes is used All pinholes of both matrices and the pixels of the CCD are in confocal position.

Development and production experience of the multilayer curtain-coated linerboard of Ji’an PM No. 3,

TAPPI Journal ◽  
2014 ◽  
Vol 13 (2) ◽  
pp. 17-25
Author(s):  
JUNMING SHU ◽  
ARTHAS YANG ◽  
PEKKA SALMINEN ◽  
HENRI VAITTINEN
Keyword(s):  
Titanium Dioxide ◽  
High Speed ◽  
Food Packaging ◽  
Production Efficiency ◽  
Positive Impact ◽  
Low Cost ◽  
Board Structure ◽  
Flexographic Printing ◽  
Curtain Coating ◽  
Coating Formulations

The Ji’an PM No. 3 is the first linerboard machine in China to use multilayer curtain coating technology. Since successful startup at the end of 2011, further development has been carried out to optimize running conditions, coating formulations, and the base paper to provide a product with satisfactory quality and lower cost to manufacture. The key challenges include designing the base board structure for the desired mechanical strength, designing the surface properties for subsequent coating operations, optimizing the high-speed running of the curtain coater to enhance production efficiency, minimizing the amount of titanium dioxide in the coating color, and balancing the coated board properties to make them suitable for both offset and flexographic printing. The pilot and mill scale results show that curtain coating has a major positive impact on brightness, while smoothness is improved mainly by the blade coating and calendering conditions. Optimization of base board properties and the blade + curtain + blade concept has resulted in the successful use of 100% recycled fiber to produce base board. The optical, mechanical, and printability properties of the final coated board meet market requirements for both offset and flexographic printing. Machine runnability is excellent at the current speed of 1000 m/min, and titanium dioxide has been eliminated in the coating formulations without affecting the coating coverage. A significant improvement in the total cost of coated white liner production has been achieved, compared to the conventional concept of using virgin fiber in the top ply. Future development will focus on combining low cost with further quality improvements to make linerboard suitable for a wider range of end-use applications, including frozen-food packaging and folding boxboard.

New Simplified Low Cost Simulation Method for SME Manufacturing System

2015 ◽  
Vol 9 (2) ◽  
pp. 206
Author(s):  
Tawfik Benabdallah ◽  
Nor Nait Sadi ◽  
Mustapha Kamel Abdi
Keyword(s):  
Manufacturing System ◽  
Low Cost ◽  
Simulation Method ◽  
Cost Simulation

Low-Cost High-Speed Techniques for Real-Time Simulation of Power Electronic Systems

2007 ◽  
Author(s):  
R. E. Crosbie ◽  
J. J. Zenor ◽  
R. Bednar ◽  
D. Word ◽  
N. G. Hingorani
Keyword(s):  
Real Time ◽  
High Speed ◽  
Low Cost ◽  
Electronic Systems ◽  
Power Electronic ◽  
Real Time Simulation ◽  
Time Simulation

High-speed electro-optic switch using buried electrode structure in polymer Mach–Zehnder waveguide

2016 ◽  
Vol 30 (06) ◽  
pp. 1650063 ◽  
Author(s):  
Jingwen Sun ◽  
Jian Sun ◽  
Yunji Yi ◽  
Lucheng Qv ◽  
Shiqi Sun ◽  
...  
Keyword(s):  
Insertion Loss ◽  
Rise Time ◽  
High Speed ◽  
Low Cost ◽  
Characteristic Parameters ◽  
Electrode Structure ◽  
Processing Cost ◽  
Electro Optic ◽  
Disperse Red 1 ◽  
Excellent Photostability

A low-cost and high-speed electro-optic (EO) switch using the guest–host EO material Disperse Red 1/Polymethyl Methacrylate (DR1/PMMA) was designed and fabricated. The DR1/PMMA material presented a low processing cost, an excellent photostability and a large EO coefficient of 13.1 pm/V. To improve the performance of the switch, the in-plane buried electrode structure was introduced in the polymer Mach–Zehnder waveguide to improve the poling and modulating efficiency. The characteristic parameters of the waveguide and the electrodes were carefully designed and the fabrication process was strictly controlled. Under 1550 nm, the insertion loss of the device was 12.7 dB. The measured switching rise time and fall time of the switch were 50.00 ns and 54.29 ns, respectively.

scholarly journals Light Cross-Linkable Marine Collagen for Coaxial Printing of a 3D Model of Neuromuscular Junction Formation

Biomedicines ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 16
Author(s):  
Borja Sanz ◽  
Ane Albillos Sanchez ◽  
Bonnie Tangey ◽  
Kerry Gilmore ◽  
Zhilian Yue ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
Neuromuscular Junction ◽  
Disease Transmission ◽  
Low Cost ◽  
Attractive Alternative ◽  
Waste Products ◽  
Environmentally Sustainable ◽  
Zoonotic Disease Transmission ◽  
And Migration

Collagen is a major component of the extracellular matrix (ECM) that modulates cell adhesion, growth, and migration, and has been utilised in tissue engineering applications. However, the common terrestrial sources of collagen carry the risk of zoonotic disease transmission and there are religious barriers to the use of bovine and porcine products in many cultures. Marine based collagens offer an attractive alternative and have so far been under-utilized for use as biomaterials for tissue engineering. Marine collagen can be extracted from fish waste products, therefore industry by-products offer an economical and environmentally sustainable source of collagen. In a handful of studies, marine collagen has successfully been methacrylated to form collagen methacrylate (ColMA). Our work included the extraction, characterization and methacrylation of Red Snapper collagen, optimisation of conditions for neural cell seeding and encapsulation using the unmodified collagen, thermally cross-linked, and the methacrylated collagen with UV-induced cross-linking. Finally, the 3D co-axial printing of neural and skeletal muscle cell cultures as a model for neuromuscular junction (NMJ) formation was investigated. Overall, the results of this study show great potential for a novel NMJ in vitro 3D bioprinted model that, with further development, could provide a low-cost, customizable, scalable and quick-to-print platform for drug screening and to study neuromuscular junction physiology and pathogenesis.

scholarly journals Towards a Glass New World: The Role of Ion-Exchange in Modern Technology

2021 ◽  
Vol 11 (10) ◽  
pp. 4610
Author(s):  
Simone Berneschi ◽  
Giancarlo C. Righini ◽  
Stefano Pelli
Keyword(s):  
Ion Exchange ◽  
Communication Networks ◽  
High Speed ◽  
High Performance ◽  
Low Cost ◽  
Modern Technology ◽  
Historical Background ◽  
Wide Range ◽  
Happy Marriage

Glasses, in their different forms and compositions, have special properties that are not found in other materials. The combination of transparency and hardness at room temperature, combined with a suitable mechanical strength and excellent chemical durability, makes this material indispensable for many applications in different technological fields (as, for instance, the optical fibres which constitute the physical carrier for high-speed communication networks as well as the transducer for a wide range of high-performance sensors). For its part, ion-exchange from molten salts is a well-established, low-cost technology capable of modifying the chemical-physical properties of glass. The synergy between ion-exchange and glass has always been a happy marriage, from its ancient historical background for the realisation of wonderful artefacts, to the discovery of novel and fascinating solutions for modern technology (e.g., integrated optics). Getting inspiration from some hot topics related to the application context of this technique, the goal of this critical review is to show how ion-exchange in glass, far from being an obsolete process, can still have an important impact in everyday life, both at a merely commercial level as well as at that of frontier research.

scholarly journals In-Plane Monolithic Integration of Scaled III-V Photonic Devices

2021 ◽  
Vol 11 (4) ◽  
pp. 1887
Author(s):  
Markus Scherrer ◽  
Noelia Vico Triviño ◽  
Svenja Mauthe ◽  
Preksha Tiwari ◽  
Heinz Schmid ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
High Speed ◽  
Low Cost ◽  
Photonic Devices ◽  
Monolithic Integration ◽  
Light Emitters ◽  
Fully Integrated ◽  
Large Lattice ◽  
Hybrid Iii ◽  
Gain Material

It is a long-standing goal to leverage silicon photonics through the combination of a low-cost advanced silicon platform with III-V-based active gain material. The monolithic integration of the III-V material is ultimately desirable for scalable integrated circuits but inherently challenging due to the large lattice and thermal mismatch with Si. Here, we briefly review different approaches to monolithic III-V integration while focusing on discussing the results achieved using an integration technique called template-assisted selective epitaxy (TASE), which provides some unique opportunities compared to existing state-of-the-art approaches. This method relies on the selective replacement of a prepatterned silicon structure with III-V material and thereby achieves the self-aligned in-plane monolithic integration of III-Vs on silicon. In our group, we have realized several embodiments of TASE for different applications; here, we will focus specifically on in-plane integrated photonic structures due to the ease with which these can be coupled to SOI waveguides and the inherent in-plane doping orientation, which is beneficial to waveguide-coupled architectures. In particular, we will discuss light emitters based on hybrid III-V/Si photonic crystal structures and high-speed InGaAs detectors, both covering the entire telecom wavelength spectral range. This opens a new path towards the realization of fully integrated, densely packed, and scalable photonic integrated circuits.

Sign in / Sign up

Export Citation Format

Share Document