scholarly journals THE IMPROVEMENT OF RAMIE FIBER PROPERTIES AS COMPOSITE MATERIALS USING ALKALIZATION TREATMENT: NaOH CONCENTRATION

2021 ◽  
Vol 22 (2) ◽  
pp. 62
Author(s):  
Umi Lailatul Jamilah ◽  
Sujito Sujito
Keyword(s):  
Tensile Strength ◽  
Composite Materials ◽  
Tensile Test ◽  
Tensile Modulus ◽  
Fiber Surface ◽  
Ramie Fiber ◽  
Test Results ◽  
Fiber Properties ◽  
Ramie Fibers ◽  
Ft Ir

THE IMPROVEMENT OF RAMIE FIBER PROPERTIES AS COMPOSITE MATERIALS USING ALKALIZATION TREATMENT: NaOH CONCENTRATION. Ramie fiber is a plant fiber that has good quality and potential as a constituent of composite materials. In this study, ramie fiber surface modification was conducted through alkalization with various at 0%, 4%, 5%, 6%, 7%, 8%, and 9% concentrations of NaOH using a magnetic stirrer with a speed of 200 rpm at 70οC for 5 hours. Alkaline ramie fibers are characterized using the Cheson method to determine the chemical composition of ramie fiber, FT-IR test to determine the function group of ramie fiber, morphological test to know the surface structure and diameter of ramie fiber, as well as tensile test to know the tensile strength and tensile modulus of PLA/ramie composite. Overall, the increase of NaOH concentration up to 8% percentage was able to increase the level of cellulose and lignin ramie fibers by 88.180 % and 2.444 %, as well as lower hemicellulose levels of 1.446 %. The alkalization treatment of 8% NaOH, optimally reduces the hydrophilic properties of the fiber. The increased concentration of NaOH makes the fiber surface cleaner and the diameter smaller, but the fiber structure is damaged at a concentration of NaOH more than 8%. Tensile test results showed that alkalized ramie fibers with an 8% concentration of NaOH produced PLA/ramie composites with the highest tensile strength and tensile modulus of 57.37 MPa and 248.25 MPa. Thus, the optimum ramie fiber properties are increased using alkalization with an 8% concentration of NaOH.

scholarly journals Effect of Ramie Fabric Chemical Treatments on the Physical Properties of Thermoset Polylactic Acid (PLA) Composites

Aerospace ◽  
2018 ◽  
Vol 5 (3) ◽  
pp. 93 ◽  
Author(s):  
Chunhong Wang ◽  
Zilong Ren ◽  
Shan Li ◽  
Xiaosu Yi
Keyword(s):  
Tensile Strength ◽  
Polylactic Acid ◽  
Alkali Treatment ◽  
Fiber Surface ◽  
Contact Angles ◽  
Ramie Fiber ◽  
Flexure Strength ◽  
Chemical Treatments ◽  
The Matrix ◽  
Ramie Fibers

Ramie fabric-reinforced thermoset polylactic acid (PLA) composites were prepared by using heat pressing technology. Fabrics were treated with alkali, silane, and alkali–silane respectively, expecting an improvement of the interface between the fabric and the matrix. Scanning electron microscopy (SEM) results indicated that after alkali treatment, impurities on the fiber surface were removed and its diameter became finer. After the silane, and alkali–silane treatments, the contact angles of the ramie fibers increased by 14.26%, and 33.12%, respectively. The contact angle of the alkali–silane treated fiber reached 76.41°; this is beneficial for the adhesion between ramie fiber and the PLA. The research revealed that the tensile strength of the fiber increased after the alkali and silane treatments. A slight decrease was noticed on the tensile strength of fibers treated with alkali–silane. After all, three chemical treatments were done, the flexure strength of the ramie fabric-reinforced PLA composites, improved in all cases. Among the three treatments, the alkali–silane treatment demonstrated the best result, as far as the flexure strength and modulus of the fabricated composites were concerned. On the other hand, water absorption of the related composites decreased by 23.70%, which might contribute to the closer contact between the ramie fiber and the matrix. The ramie fabric-reinforced PLA composites, prepared in this study, can meet the standard requirements of aircraft interior structures and have favorable application foreground.

Size Effect on Mechanical Properties of LVL

2014 ◽  
Vol 887-888 ◽  
pp. 824-829
Author(s):  
Qing Fang Lv ◽  
Ji Hong Qin ◽  
Ran Zhu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Size Effect ◽  
Tensile Test ◽  
Compression Test ◽  
Test Results ◽  
Laminated Veneer Lumber ◽  
Object Of Study ◽  
The Relationship

Laminated veneer lumber is taken as an object of study, and use LVL specimens of different sizes for compression test and tensile test. The goal of the experiment is to investigate the size effect on compressive strength and tensile strength as well as the influence of the secondary glued laminated face, which appears in the secondary molding processes. The results show that both compressive strength and tensile strength have the size effect apparently and the existence of the secondary glued laminated face lower the compressive strength of LVL specimens. Afterwards, the relationship between compressive strength and volume along with tensile strength and area are obtained by the test results.

Durability study of ramie fiber fabric reinforced phenolic plates under humidity conditions

2016 ◽  
Vol 23 (1) ◽  
pp. 45-52 ◽  
Author(s):  
Guijun Xian ◽  
Peng Yin ◽  
Innocent Kafodya ◽  
Hui Li ◽  
Wei-lun Wang
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Tensile Modulus ◽  
Resin Matrix ◽  
Ramie Fiber ◽  
Short Beam ◽  
Low Degree ◽  
Beam Shear ◽  
Ramie Fibers ◽  
Fiber Fabric

AbstractA durability study of a ramie fiber fabric reinforced phenolic resin (RFRP) plate under 50%, 85%, and 98% relative humidity for 6 months at room temperature was performed. Water absorption and desorption, tensile and short beam shear strengths of the RFRP plates were investigated as a function of exposure time. RFRP samples show strong hydrophilic characteristics and the saturated water content varies from 0.73% to 4.5% with relative humidity ranging from 50% to 98%. After 6 months of exposure to 98% relative humidity, an abnormal extra amount of moisture was absorbed, which may have resulted from cracks in the resin matrix or from debonding between fiber and resin due to swelling of the fibers with high moisture content. It was found that the tensile modulus is more susceptible to moisture uptake, which is ascribed to the degradation of ramie fibers with the water ingress. An approximate linearity between the mechanical properties and the moisture content is observed if the abnormal extra water uptake is neglected. Both tensile and short beam shear strengths of the RFRP samples recovered remarkably when samples were fully dried at 60°C, indicating a low degree of permanent degradation occurred due to the exposure.

The High-Temperature Tensile Test of Quartz Fiber Fabric- Reinforced Resin Composites

2021 ◽  
Vol 904 ◽  
pp. 188-195
Author(s):  
Hua Qiong Wang ◽  
Li Li Zhang ◽  
Da Cheng Jiao ◽  
Yan Ru Wang ◽  
Zeng Hua Gao
Keyword(s):  
Tensile Strength ◽  
High Temperature ◽  
Tensile Test ◽  
Tensile Properties ◽  
Tensile Modulus ◽  
National Standard ◽  
Resin Composites ◽  
Quartz Fiber ◽  
High Temperature Tensile ◽  
Fiber Fabric

The tensile properties of quartz fiber fabric-reinforced resin composites at high temperature were studied. The effects of specimen type and dimension, temperature loading procedure, holding time and loading rate on the tensile properties of the composites at high temperatures were analyzed through series of comparative experiments, the tensile test parameters were determined. Chinese national standard for high-temperature tensile property testing of the composites was compiled based on the data collected. According to the established standard, the tensile testing at 500°C was carried out. Compared with the tensile properties at room temperature, the tensile strength and tensile modulus of the composite at high temperature decreases significantly, with the tensile strength decreasing by about 42.32% and the tensile modulus decreasing by about 24.18%. This is mainly due to the high temperature which causes part of the resin matrix to pyrolyze and detach from around the fiber, thus losing the integrity of the material. In addition, this national standard for high-temperature tensile properties has some general applicability to different types of fiber-reinforced resin composites.

scholarly journals Influence of Spinning Temperature and Filler Content on the Properties of Melt-Spun Soy Flour/Polypropylene Fibers

Fibers ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 83 ◽  
Author(s):  
Ozgun Guzdemir ◽  
Amod A. Ogale
Keyword(s):  
Yield Strength ◽  
Filler Content ◽  
Low Cost ◽  
Tensile Modulus ◽  
Fiber Surface ◽  
Soy Flour ◽  
Processing Temperature ◽  
Fiber Properties ◽  
Melt Spun ◽  
Renewable Material

Polypropylene (PP) fibers are heavily used in disposable nonwovens fabrics because of their desirable properties and low-cost, but they are not biodegradable. With the goal of reducing non-biodegradable plastic waste in the environment, the primary aim of this study was to produce fibers with reduced content of PP for disposable fabrics by incorporating soy flour, a bio-based renewable material. An optimum processing temperature of 190 °C was established, and thin fibers with a diameter under 60 µm were successfully melt-spun. Inclusion of compatibilized soy (SFM) at 30 wt% resulted in fibers with a tensile modulus of 674 ± 245 MPa and a yield strength of 18 ± 4 MPa. At 15 wt% SFM, fiber tensile modulus and yield strength were 914 ± 164 and 29 ± 3, respectively. Although lower than those of neat PP fibers (1224 ± 136 MPa and 37 ± 3 MPa), these SFM/PP fiber properties are suitable for nonwoven applications. Additionally, partial presence of soy particulates on fiber surface imparted enhanced water absorption and colorability properties to the fibers while imparting the fibers the feel of natural fibers.Although more difficult to produce, soy-PP fibers possessed similar properties as compared to those of than soy-PE fibers reported in earlier studies.

PENGARUH LAMA WAKTU PENGGETARAN ULTRASONIC BATH TERHADAP SIFAT MEKANIK DAN MORFOLOGI PATAHAN BIOKOMPOSIT PATI TAPIOKA/SERAT RAMI (BOEHMERIA NIVEA)

ROTOR ◽  
2017 ◽  
Vol 10 (2) ◽  
pp. 23
Author(s):  
Mochamad Asrofi ◽  
Hairul Abral ◽  
Anwar Kasim ◽  
Adjar Pratoto ◽  
Herwin Gevin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fracture Surface ◽  
Tensile Test ◽  
Dry Weight ◽  
Ramie Fiber ◽  
Compact Structure ◽  
Tapioca Starch ◽  
Ultrasonic Bath ◽  
Vibration Time

This study reported about mechanical properties and fracture surface of ramie fiber reinforced tapioca starch based biocomposites. The amount of fibers in matrix was kept constant at 10% from dry weight starch basis. Fabrication of biocomposites was solution casting. The effect of vibration duration from ultrasonic bath was 0, 15, 30, and 45 min. This treatment was applied to biocomposites while gelatinized. Tensile test was carried out to determine the mechanical properties of biocomposites. Fracture surface of biocomposites after tensile test was observed by using scanning electron microscopy (SEM). The result shows that, tensile strength increased when vibration time was added. The maximum tensile strength was obtained at 45 min vibration time with 2,84 MPa. This phenomenon was supported by SEM observation which indicate compact structure. Keywords: Tapioca starch, ramie fiber, biocomposites, mechanical properties, SEM

Statistical Evaluation Tensile Properties of High-Density Polyethylenes

2012 ◽  
Vol 445 ◽  
pp. 213-218 ◽  
Author(s):  
Ahmet Koyun ◽  
Baris Koksal ◽  
Esma Ahlatcioglu ◽  
A. Binnaz Hazar Yoruc
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Tensile Test ◽  
Statistical Evaluation ◽  
Test Results ◽  
Plastic Materials ◽  
Service Conditions ◽  
End Use ◽  
Chain Lengths

The mechanical properties, among all the properties of plastic materials, are often the most important properties because virtually all service conditions and the majority of end-use applications involve some degree of mechanical loading [1]. In the present work three different commercial polyethylene materials are tensile tested at four or five different tensile rates and two or three temperatures. Tensile test results against tensile rate include stress at 0.5 % elongation, tensile strength, yield strength, modulus of elasticity, elongation at yield and % elongation are determined. It is concluded that the structure, chain lengths and branching rates of polymer matrix significantly effected tensile test curve characteristic.

Experimental investigation of recycled aggregate effect on the concrete properties

2018 ◽  
Vol 9 (4) ◽  
pp. 560-571
Author(s):  
Hamed Hemmati Pourghashti ◽  
Malek Mohammad Ranjbar ◽  
Rahmat Madandoust
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Tensile Test ◽  
Recycled Concrete ◽  
Test Results ◽  
Content Type ◽  
Treatment Conditions ◽  
Natural Aggregates ◽  
Direct Tensile ◽  
Direct Tensile Test

Purpose The purpose of this paper is to conduct a laboratory investigation on measuring the tensile strength of recycled concrete using a double punch test. Furthermore, one of the main goals of this study is to compare the tensile and compressive strengths of recycled concrete samples. Design/methodology/approach Recycled concrete samples were made with variables such as aggregate type (natural stone and aggregate recycled concrete), different water-to-cement ratios and different treatment conditions in the first stage. In the next stage, the double punch test was performed on them, and finally the results obtained from experiments were analyzed and investigated. Findings According to the above tests, it was concluded that: first, according to the laboratory results, the strength of concrete containing recycled aggregates becomes closer to the strength of concrete containing natural aggregates whenever the water-to-cement ratio is higher. Second, upon investigating the treatment conditions, it was observed that the treatment had a greater effect on the strength of the recycled concrete. However, this effect was less tangible in tensile strength. Third, upon investigating the results of tensile strength, it can be said that the Barcelona test results were closer to the direct tensile test results compared to the Brazilian test results. This indicates the higher viability of Barcelona’s test results. Fourth, the results obtained from the Barcelona tensile test for recycled concrete were closer to the results of the direct tensile test compared to the concrete containing natural aggregates, which suggests that the Barcelona test is more suitable as a tensile test for recycled concrete. Fifth, the effects of various factors on tensile strength were somewhat less compared to the compressive strength, although very close. Sixth, the relationships provided by the regulation for concrete tensile strength on compressive strength were highly inconsistent with the results obtained from the direct tensile test, for which the consistency was higher for concrete containing natural aggregates compared to recycled concrete. Seventh, the dispersion of results obtained from tensile tests was higher for recycled concrete compared to concrete containing natural aggregates, but lesser of this dispersion was observed in the compressive strength. Originality/value According to the laboratory results, the strength of concrete containing recycled aggregates becomes closer to the strength of concrete containing natural aggregates whenever the water-to-cement ratio is higher. Upon investigating the treatment conditions, it was observed that the treatment had a greater effect on the strength of the recycled concrete. However, this effect was less tangible in tensile strength. On the basis on the results of the tensile strength, it can be said that the Barcelona test results were closer to the results of the direct tensile test compared to those of the Brazilian test. This indicates the higher viability of Barcelona’s test results. The results obtained from the Barcelona tensile test for recycled concrete were closer to the results of direct tensile test compared to the concrete containing natural aggregates, which suggests that the Barcelona test is more suitable as a tensile test for recycled concrete. The effects of various factors on tensile strength were somewhat less compared to the compressive strength, although very close. The relationships provided by the regulation for concrete tensile strength on compressive strength were highly inconsistent with the results obtained from the direct tensile test, for which the consistency was higher for concrete containing natural aggregate compared to recycled concrete. The dispersion of results obtained from tensile tests was higher for recycled concrete compared to concrete containing natural aggregate, but lesser of this dispersion was observed in the compressive strength.

Influence of Strain Rate and Yarn Number on Tensile Test Results

1992 ◽  
Vol 62 (10) ◽  
pp. 586-589 ◽  
Author(s):  
L. Vangheluwe
Keyword(s):  
Tensile Test ◽  
Strain Rate ◽  
Tensile Modulus ◽  
Experimental Stress ◽  
Test Results ◽  
Stress Strain ◽  
Tensile Curve

The influence of strain rate and yarn number on tensile test results is investigated using a model to describe the tensile curve. A good correlation is obtained with the experimental stress-strain curves. The influence of the yarn number on the tensile modulus and the tensile curve is not quite the same for ring and rotor yarns.

Sign in / Sign up

Export Citation Format

Share Document