scholarly journals Materials for Outer Shell of 1.170 GWh (1.00669 Kilo Ton TNT) Fusion Device - Weight Basis

2021 ◽  
Author(s):  
Muhammad Musaddique Ali Rafique
Keyword(s):  
Ion Beam ◽  
High Hardness ◽  
High Strength ◽  
Outer Shell ◽  
X Rays ◽  
Anisotropic Properties ◽  
High Entropy ◽  
Beam Focusing ◽  
Fusion Device ◽  
At Will

With recent developments in fusion engineering, interest has sparked in development of fusion devices for deterrent. Enormous amount of energy generated by combining two light nuclei could be contained and manipulated at will to trigger and accelerate micro explosions (from shock wave, x-rays or ion beam focusing) which finally result in full scale blast. Materials required to make such device are critical. They must possess high strength, high hardness, ductility, formability, drawability, and anisotropic properties. High entropy alloys (HEA) are new class of materials which nicely fulfils this requirement. Essentially, they are solid solutions of multi principal elements (usually > 5) eliminating the need of base metal as in conventional alloys. This gives them many unique properties which may be tailored at will (heat treatment, cold rolling, precipitation, irradiation). They also exhibit excellent directional properties with formation of distinct bands along certain preferred crystallographic planes even in hexagonal close packed structures. These anisotropic properties are strong function of rolling, working, or forging (swaging) direction and can be utilized to benefit. This study encompasses making outer shell of a typical fusion device selected on the basis of the weight, which is a function of area of pay load bay of carrier aircraft.

Microstructure and Mechanical Properties of FeNiCrCuAl High Entropy Alloys

2014 ◽  
Vol 1036 ◽  
pp. 101-105
Author(s):  
Gheorghe Buluc ◽  
Iulia Florea ◽  
Oana Bălţătescu ◽  
Costel Roman ◽  
Ioan Carcea
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
High Hardness ◽  
High Strength ◽  
High Entropy Alloys ◽  
Engineering Applications ◽  
High Entropy ◽  
Good Thermal Stability ◽  
Microstructure And Mechanical Properties ◽  
Wide Range

This paper presents the microstructure and the mechanical properties of FeNiCrCuAl high entropy alloys. The microstructure and mechanical properties of the annealed FeNiCrCuAl high entropy alloys were investigated using scanning electron microscopy, and X-ray diffraction. High entropy alloys have been known as a new type of materials and have been defined as having five or more principal elements, each one having a concentration between 5 and 35 at.%. Previous researches show that HEAs can be processed to form simple solid solution structures instead of intermetallics and other complicated compounds. This phenomenon is commonly attributed to the high configurational entropy in the solid solution state of HEAs. Furthermore, HEAs have also exhibited interesting properties such as high hardness and high strength, good thermal stability outstanding wear and oxidation resistance which offer great potential for engineering applications. The HEA systems explored in the past decade show that metallic elements are the most commonly used, e.g. Al, Cr, Fe, Co, Ni, Cu,Ti, etc. A wide range of HEAs exhibit high hardness, high strength, distinctive electrical and magnetic properties, high-temperature softening resistance, as well as favorable combination of compression strength and ductility. This combination of properties and the particular structures of HEAs are attractive for a number of potential engineering applications.

scholarly journals Design and Development of High Entropy Alloys Using Artificial Intelligence

2021 ◽  
Author(s):  
Shailesh Kumar Singh ◽  
Vivek K. Singh
Keyword(s):  
Artificial Intelligence ◽  
Material Properties ◽  
High Performance ◽  
High Hardness ◽  
High Strength ◽  
Material Model ◽  
High Entropy Alloys ◽  
Principal Element ◽  
Elevated Temperature Strength ◽  
High Entropy

The conventional design approach of alloys initiates with one principal element and continues by adding several alloying elements to obtain desired properties. In this method, the intrinsic properties of the designed alloy are governed by the principal element. For example, in steel alloy, iron is the principal element, Aluminium in aluminium alloy, and so on. Compared to the conventional alloy, high entropy alloys do not have any dominating elements; all the elements present in these alloys either have an equal or near-equal ratio of elements. As reported in the literature, these alloys exhibit interesting material properties such as high strength, high hardness, improved elevated temperature strength, and magnetic properties. These characteristics make HEAs a suitable option for high-performance applications in the aero engine, aerospace structures, and machine tools. High entropy alloy has multiple principal elements as shown in schematic diagram 1; it leads to much higher possible compositions than conventional alloys. The huge compositional space provides an opportunity to improve desired mechanical properties. If it is explored through “trial and error,” it will be challenging and cumbersome. Therefore, search schemes that can competently and promptly recognize particular alloys with desired properties are essential. Artificial Intelligence is a useful tool to model, discover, and optimize new alloys that enable predicting individual material properties as a function of composition. While the application of Artificial Intelligence is quite popular in many aspects of society, its usage in material informatics is still in the nascent stage. The algorithm used in artificial intelligence is trained to pick up predictive rules from data and create a material model quicker than a computational model and can even generate the model for which no physical model exists. Artificial Intelligence (AI) allows predicting a set of experiments to be conducted to detect new alloy having desired properties. Thus, AI can be used as a valuable tool to optimize the development of new alloys.

The Basic Physical Principles of Ion, Electron, and X-Ray Detectors and Their Application to Microanalysis

1985 ◽  
Vol 43 ◽  
pp. 154-157
Author(s):  
A.J. Tousimis
Keyword(s):  
Ion Beam ◽  
Depth Resolution ◽  
Sample Surface ◽  
High Energy ◽  
X Rays ◽  
X Ray ◽  
Electrons And Ions ◽  
Spatial Depth ◽  
Minimum Surface Area ◽  
Physical Principles

An integral and of prime importance of any microtopography and microanalysis instrument system is its electron, x-ray and ion detector(s). The resolution and sensitivity of the electron microscope (TEM, SEM, STEM) and microanalyzers (SIMS and electron probe x-ray microanalyzers) are closely related to those of the sensing and recording devices incorporated with them.Table I lists characteristic sensitivities, minimum surface area and depth analyzed by various methods. Smaller ion, electron and x-ray beam diameters than those listed, are possible with currently available electromagnetic or electrostatic columns. Therefore, improvements in sensitivity and spatial/depth resolution of microanalysis will follow that of the detectors. In most of these methods, the sample surface is subjected to a stationary, line or raster scanning photon, electron or ion beam. The resultant radiation: photons (low energy) or high energy (x-rays), electrons and ions are detected and analyzed.

The stabilization of B.C.C. Cu in Cu/Nb nanolayered composites

1996 ◽  
Vol 54 ◽  
pp. 228-229
Author(s):  
H. Kung ◽  
A.J. Griffin ◽  
Y.C. Lu ◽  
K.E. Sickafus ◽  
T.E. Mitchell ◽  
...  
Keyword(s):  
Electrical Resistivity ◽  
Layer Thickness ◽  
Volume Fraction ◽  
Ion Beam ◽  
High Strength ◽  
Cross Sectional ◽  
Metastable Structure ◽  
High Resolution Tem ◽  
Potential Improvement ◽  
Two Phases

Materials with compositionally modulated structures have gained much attention recently due to potential improvement in electrical, magnetic and mechanical properties. Specifically, Cu-Nb laminate systems have been extensively studied mainly due to the combination of high strength, and superior thermal and electrical conductivity that can be obtained and optimized for the different applications. The effect of layer thickness on the hardness, residual stress and electrical resistivity has been investigated. In general, increases in hardness and electrical resistivity have been observed with decreasing layer thickness. In addition, reduction in structural scale has caused the formation of a metastable structure which exhibits uniquely different properties. In this study, we report the formation of b.c.c. Cu in highly textured Cu/Nb nanolayers. A series of Cu/Nb nanolayered films, with alternating Cu and Nb layers, were prepared by dc magnetron sputtering onto Si {100} wafers. The nominal total thickness of each layered film was 1 μm. The layer thickness was varied between 1 nm and 500 nm with the volume fraction of the two phases kept constant at 50%. The deposition rates and film densities were determined through a combination of profilometry and ion beam analysis techniques. Cross-sectional transmission electron microscopy (XTEM) was used to examine the structure, phase and grain size distribution of the as-sputtered films. A JEOL 3000F high resolution TEM was used to characterize the microstructure.

AMPCO 483

Alloy Digest ◽  
1978 ◽  
Vol 27 (4) ◽  
Keyword(s):  
Corrosion Resistance ◽  
Physical Properties ◽  
Tensile Properties ◽  
Base Alloy ◽  
High Hardness ◽  
High Strength ◽  
Heat Treating ◽  
Good Resistance ◽  
Copper Base ◽  
Copper Base Alloy

Abstract AMPCO 483 is a copper-base alloy that can be used in the cast or wrought form. It provides high strength, high hardness, excellent resistance to corrosion and good resistance to fatigue and wear. It is well suited for service at temperatures up to 750 F and for applications such as pickling equipment, nuts and marine hardware. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on corrosion resistance as well as casting, forming, heat treating, machining, and joining. Filing Code: Cu-352. Producer or source: Ampco Metal Inc..

Research on High-Speed Cutting of Cr12MoV Hardened Steel - A Review

2020 ◽  
Vol 15 ◽  
Author(s):  
Fei Sun ◽  
Guohe Li ◽  
Qi Zhang ◽  
Meng Liu
Keyword(s):  
High Speed ◽  
Cutting Temperature ◽  
High Hardness ◽  
High Strength ◽  
Hardened Steel ◽  
Parameters Optimization ◽  
Future Research ◽  
High Speed Machining ◽  
Machined Surface ◽  
Stamping Die

: Cr12MoV hardened steel is widely used in the manufacturing of stamping die because of its high strength, high hardness, and good wear resistance. As a kind of mainstream cutting technology, high-speed machining has been applied in the machining of Cr12MoV hardened steel. Based on the review of a large number of literature, the development of high-speed machining of Cr12MoV hardened steel was summarized, including the research status of the saw-tooth chip, cutting force, cutting temperature, tool wear, machined surface quality, and parameters optimization. The problems that exist in the current research were discussed and the directions of future research were pointed out. It can promote the development of high-speed machining of Cr12MoV hardened steel.

scholarly journals Understanding the Links between the Composition-Processing-Properties in New Formulations of HEAs Sintered by SPS

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 888
Author(s):  
Paula Alvaredo-Olmos ◽  
Jon Molina-Aldareguía ◽  
Alvaro Vaz-Romero ◽  
Estela Prieto ◽  
Jesús González-Julián ◽  
...  
Keyword(s):  
High Hardness ◽  
Processing Parameters ◽  
Heating Rates ◽  
High Entropy ◽  
Plasma Sintering ◽  
Mechanical Study ◽  
Spark Plasma ◽  
Processing Properties ◽  
Bcc Phase ◽  
Hardness Values

This work presents two new compositions of high entropy alloys (HEAs) that were designed with the aim of obtaining a body-centered cubic (BCC) phase with high hardness values and a moderate density. Sintering was performed using Spark Plasma Sintering (SPS) with different heating rates to determine the influence of the processing parameters on the phase formation. The microstructural study revealed that the presence of Ni in the composition promoted phase separation, and the mechanical study confirmed a clear influence on the mechanical properties of both the composition and heating rate. The combination of microscopy with compression and nanoindentation tests at room and high temperature made it possible to advance our understanding of the relationships between the composition, processing, and properties of this emerging group of alloys.

scholarly journals Al-driven peculiarities of local coordination and magnetic properties in single-phase Alx-CrFeCoNi high-entropy alloys

Nano Research ◽  
2021 ◽  
Author(s):  
Alevtina Smekhova ◽  
Alexei Kuzmin ◽  
Konrad Siemensmeyer ◽  
Chen Luo ◽  
Kai Chen ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Single Phase ◽  
Magnetic Circular Dichroism ◽  
Surface Region ◽  
Face Centered Cubic ◽  
X Rays ◽  
X Ray ◽  
High Entropy ◽  
X Ray Absorption ◽  
Absorption Edges

AbstractModern design of superior multi-functional alloys composed of several principal components requires in-depth studies of their local structure for developing desired macroscopic properties. Herein, peculiarities of atomic arrangements on the local scale and electronic states of constituent elements in the single-phase face-centered cubic (fcc)- and body-centered cubic (bcc)-structured high-entropy Alx-CrFeCoNi alloys (x = 0.3 and 3, respectively) are explored by element-specific X-ray absorption spectroscopy in hard and soft X-ray energy ranges. Simulations based on the reverse Monte Carlo approach allow to perform a simultaneous fit of extended X-ray absorption fine structure spectra recorded at K absorption edges of each 3d constituent and to reconstruct the local environment within the first coordination shells of absorbers with high precision. The revealed unimodal and bimodal distributions of all five elements are in agreement with structure-dependent magnetic properties of studied alloys probed by magnetometry. A degree of surface atoms oxidation uncovered by soft X-rays suggests different kinetics of oxide formation for each type of constituents and has to be taken into account. X-ray magnetic circular dichroism technique employed at L2.3 absorption edges of transition metals demonstrates reduced magnetic moments of 3d metal constituents in the sub-surface region of in situ cleaned fcc-structured Al0.3-CrFeCoNi compared to their bulk values. Extended to nanostructured versions of multicomponent alloys, such studies would bring new insights related to effects of high entropy mixing on low dimensions.

scholarly journals Development of Novel Lightweight Al-Rich Quinary Medium-Entropy Alloys with High Strength and Ductility

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4223
Author(s):  
Po-Sung Chen ◽  
Yu-Chin Liao ◽  
Yen-Ting Lin ◽  
Pei-Hua Tsai ◽  
Jason S. C. Jang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Compressive Strain ◽  
High Strength ◽  
Fine Tuning ◽  
Face Centered Cubic ◽  
Transportation Industry ◽  
High Entropy ◽  
Good Potential ◽  
Face Centered

Most high-entropy alloys and medium-entropy alloys (MEAs) possess outstanding mechanical properties. In this study, a series of lightweight nonequiatomic Al50–Ti–Cr–Mn–V MEAs with a dual phase were produced through arc melting and drop casting. These cast alloys were composed of body-centered cubic and face-centered cubic phases. The density of all investigated MEAs was less than 5 g/cm3 in order to meet energy and transportation industry requirements. The effect of each element on the microstructure evolution and mechanical properties of these MEAs was investigated. All the MEAs demonstrated outstanding compressive strength, with no fractures observed after a compressive strain of 20%. Following the fine-tuning of the alloy composition, the Al50Ti20Cr10Mn15V5 MEA exhibited the most compressive strength (~1800 MPa) and ductility (~34%). A significant improvement in the mechanical compressive properties was achieved (strength of ~2000 MPa, strain of ~40%) after annealing (at 1000 °C for 0.5 h) and oil-quenching. With its extremely high specific compressive strength (452 MPa·g/cm3) and ductility, the lightweight Al50Ti20Cr10Mn15V5 MEA demonstrates good potential for energy or transportation applications in the future.

Sign in / Sign up

Export Citation Format

Share Document