Multistage Openhole Completion Using Integrated Dynamic Diversion Frac Technique in Highly Depleted Well: First Successful Application in West Kuwait Field

2021 ◽  
Author(s):  
Abdullah Abu-Eida ◽  
Salem Al-Sabea ◽  
Milan Patra ◽  
Bader Akbar ◽  
Kutbuddin Bhatia ◽  
...  
Keyword(s):  
Best Practice ◽  
Treatment Options ◽  
High Energy ◽  
Lessons Learned ◽  
High Potential ◽  
Fracture Plane ◽  
Fluid Loss ◽  
Field Development ◽  
Two Fluids

Abstract The Minagish field in West Kuwait is a high potential field which poses several challenges in terms of hydrocarbon flow assurance through highly depleted tight carbonate intervals with uneven reservoir quality and curtailed mobility. These conditions have shifted the field development from vertical to horizontal wellbore completions. Achieving complete wellbore coverage is a challenge for any frac treatment performed in a long openhole lateral with disparities in reservoir characteristics. The fluid will flow into the path of least resistance leaving large portions of the formation untreated. As a result, economic fracturing treatment options dwindle significantly, thus reservoir stimulation results are not always optimum. A multistage fracturing technique using Integrated Dynamic Diversion (IDD) has been performed first time in West Kuwait field well. The process uses active fluid energy to divert flow into a specific fracture point in the lateral, which can initiate and precisely place a fracture. The process uses two self-directed fluid streams: one inside the pipe and one in the annulus. The process mixes the two fluids downhole with high energy to form a consistent controllable mixture. The technique includes pinpoint fluid jetting at the point of interest, followed by in-situ HCL based crosslinked systems employed for improving individual stage targets. The IDD diversion shifts the fracture to unstimulated areas to create complex fractures which increases reservoir contact volume and improved overall conductivity in the lateral. The kinetic and chemical diversion of the IDD methodology is highly critical to control fluid loss in depleted intervals and results in enhanced stimulation. Pumping a frac treatment in openhole without control would tend to initiate a longitudinal fracture along the wellbore and may restrict productivity. By using specialized completion tools with nozzles at the end of the treating string, a new pinpoint process has been employed to initiate a transverse fracture plane in IDD applications. Proper candidate selection and fluid combination with in-situ crosslink acid effectively plug the fracture generated previously and generate pressure high enough to initiate another fracture for further ramification. By combining these processes into one continuous operation, the use of wireline/coiled tubing for jetting, plug setting and milling is eliminated, making the new multistage completion technology economical for these depleted wells. The application of the IDD methodology is a fit-for-purpose solution to address the unique challenges of openhole operations, formation technical difficulties, high-stakes economics, and untapped high potential from intermittent reservoirs. The paper will present post-operation results of this completion from all fractured zones along the lateral and will describe the lessons learned in implementation of this methodology which can be considered as best practice for application in similar challenges in other fields.

Enhanced Productivity in Horizontal Open Hole Completion Using Integrated Dynamic Diversion Acid Squeeze Technique in Highly Depleted Well: Successful Application in West Kuwait Field

2021 ◽  
Author(s):  
Salem Al-Sabea ◽  
Abdullah Abu-Eida ◽  
Milan Patra ◽  
Yousef Haider ◽  
Hasan Al Qattan ◽  
...  
Keyword(s):  
Acid Treatment ◽  
Best Practice ◽  
Treatment Options ◽  
High Energy ◽  
Lessons Learned ◽  
High Potential ◽  
Fluid Loss ◽  
Selective Treatment ◽  
Field Development ◽  
Open Hole

Abstract The Minagish field in West Kuwait is a high potential field which poses several challenges in terms of hydrocarbon flow assurance through highly depleted tight carbonate intervals with uneven reservoir quality and curtailed mobility. These conditions have shifted the field development from vertical to horizontal wellbore completions. Achieving complete wellbore coverage is a challenge for any Matrix Acid treatment performed in a long openhole lateral with disparities in reservoir characteristics. The fluid will flow into the path of least resistance leaving large portions of the formation untreated. As a result, economic Acid treatment options dwindle significantly, thus reservoir stimulation results are not always optimum. A multistage acid stimulation technique using Integrated Dynamic Diversion (IDD) has been performed in a West Kuwait field well. The process uses active fluid energy to divert flow into a specific sweet point (high pressure point) in the lateral, which can pinpoint and precisely place acid treatment at the desired location. The process uses two self-directed fluid streams: one inside the pipe and one in the annulus. The process mixes the two fluids downhole with high energy to form a consistent controllable mixture. The technique includes pinpoint fluid jetting at the point of interest, followed by customized foamed HCL acid systems employed for improving individual stage targets in depleted reservoir. The IDD diversion shifts the acid treatment to unstimulated areas to create complex wormholes which increase reservoir contact volume and improve overall conductivity in the lateral. The kinetics and chemical diversion of the IDD methodology are highly critical to control fluid loss in depleted intervals and results in enhanced stimulation. The application of the IDD methodology is a fit-for-purpose solution to address the unique challenges of openhole operations, formation technical difficulties, high-stakes economics, and untapped high potential from intermittent reservoirs. By utilizing this application in one continuous operation, the use of chemical diverters, straddle packers and mechanical plugs for selective treatment in open hole is eliminated, making this multistage completion technology economical for these depleted wells. The paper presents results obtained after stimulating multiple zones along the lateral and describes the lessons learned in the implementation of this methodology. Going forward, the methods described, which can be considered a best practice for application to similar challenges in other fields. Proper candidate selection, optimum completion tools, and the fluid combination of in-situ gel-based diverter used to temporary plug the acid stimulated zone and foamed acid created an increase in the oil production of 430 BOPD.

Application of Integrated Far-Field Diversion Technology in Multistage Acid-Fracturing: Lesson Learnings from Unconventional Field North Kuwait

2022 ◽  
Author(s):  
Abdullah Al-Enezi ◽  
Mohammed Al-Othman ◽  
Mishari Al-Shtail ◽  
Yousef Al-Sadeeqi ◽  
Kutbuddin Bhatia ◽  
...  
Keyword(s):  
Best Practice ◽  
Treatment Options ◽  
Vital Role ◽  
High Potential ◽  
Direct Result ◽  
Far Field ◽  
Field Development ◽  
Acid Fracturing ◽  
Well Completion

Abstract The unconventional Bahrah field is a high potential field which poses several challenges in terms of hydrocarbon flow assurance through highly heterogeneous tight carbonate intervals with poor reservoir quality and curtailed mobility. Due to this, the field development strategies have prioritized well completion using horizontal acid fracturing technology over vertical wells. During fracturing, the acid system tends to form highly conductive channels in the formation. Most of the fluid will flow into the path of least resistance leaving large portions of the formation untreated. As a result, the fracturing treatment options dwindle significantly, thus reservoir stimulation results are not optimum in each stage. Achieving complete wellbore coverage is a challenge for any acid frac treatment performed in long lateral with variations in reservoir characteristics. The multistage acid fracturing using Integrated Far-field Diversion (IFD) is performed using selective openhole completion, enabling mechanical annular segmentation of the wellbore using swellable packers and sliding sleeves. The mechanical as well as chemical diversion in IFD methodology is highly important to the overall stimulation success. The technique includes pumping multiple self-degrading particle sizes, considering the openhole annular space and wide presence of natural fractures, followed by in-situ HCL based crosslinked system employed for improving individual stage targets. A biomodal strategy is employed wherein larger particles are supplemented with smaller that can bridge pore throats of the larger particles and have the desired property of rigidity and develop a level of suppleness once exposed to reservoir conditions. The IFD diversion shifts the fracture to unstimulated areas to create complex fractures that increase reservoir contact volume and improving overall conductivity. This paper examines IFD in acid fracturing and describes the crucial diversion strategy. Unlike available diverters used in other fields, the particulates are unaffected at low pH values and in live acids. Proper agent selection and combination with in-situ crosslink acid effectively plug the fracture generated previously and generate pressure high enough to initiate another fracture for further ramification. The optimization and designing of the IFD diversion in each stage plays a key role and has helped to effectively plug fractures and realize segmentation. Concentration of diversion agents, volume of fluid system and open-hole stage length sensitivity plays vital role for the success of this treatment. The application of IFD methodology is tuned as fit-for-purpose to address the unique challenges of well operations, formation technical difficulties, high-stakes economics, and untapped high potential from this unconventional reservoir. A direct result of this acid fracturing treatment is that the post-operation data showed high contribution of all fractured zones along the section in sustained manner. Furthermore, this methodology can be considered as best practice for application in unconventional challenges in other fields.

In situ TEM studies of irradiation effects for materials improvement

1991 ◽  
Vol 49 ◽  
pp. 452-453
Author(s):  
Charles W. Allen
Keyword(s):  
Nuclear Reactor ◽  
Austenitic Stainless Steels ◽  
High Energy ◽  
Point Of View ◽  
In Situ Tem ◽  
Irradiation Effects ◽  
Tem Analysis ◽  
Radiation Induced ◽  
Analytical Tools

Irradiation effects studies employing TEMs as analytical tools have been conducted for almost as many years as materials people have done TEM, motivated largely by materials needs for nuclear reactor development. Such studies have focussed on the behavior both of nuclear fuels and of materials for other reactor components which are subjected to radiation-induced degradation. Especially in the 1950s and 60s, post-irradiation TEM analysis may have been coupled to in situ (in reactor or in pile) experiments (e.g., irradiation-induced creep experiments of austenitic stainless steels). Although necessary from a technological point of view, such experiments are difficult to instrument (measure strain dynamically, e.g.) and control (temperature, e.g.) and require months or even years to perform in a nuclear reactor or in a spallation neutron source. Consequently, methods were sought for simulation of neutroninduced radiation damage of materials, the simulations employing other forms of radiation; in the case of metals and alloys, high energy electrons and high energy ions.

In situ irradiation effects studies in medium- and high-voltage TEM

1995 ◽  
Vol 53 ◽  
pp. 234-235
Author(s):  
Charles W. Allen
Keyword(s):  
Cross Section ◽  
Particle Flux ◽  
Threshold Value ◽  
High Energy ◽  
Irradiation Damage ◽  
Defect Complexes ◽  
Lattice Position ◽  
Electrons And Ions ◽  
The Masses

With respect to structural consequences within a material, energetic electrons, above a threshold value of energy characteristic of a particular material, produce vacancy-interstial pairs (Frenkel pairs) by displacement of individual atoms, as illustrated for several materials in Table 1. Ion projectiles produce cascades of Frenkel pairs. Such displacement cascades result from high energy primary knock-on atoms which produce many secondary defects. These defects rearrange to form a variety of defect complexes on the time scale of tens of picoseconds following the primary displacement. A convenient measure of the extent of irradiation damage, both for electrons and ions, is the number of displacements per atom (dpa). 1 dpa means, on average, each atom in the irradiated region of material has been displaced once from its original lattice position. Displacement rate (dpa/s) is proportional to particle flux (cm-2s-1), the proportionality factor being the “displacement cross-section” σD (cm2). The cross-section σD depends mainly on the masses of target and projectile and on the kinetic energy of the projectile particle.

In situ TEM Studies of agglomeration of sub-nanometer Ru layers in Ru/C multilayers

1992 ◽  
Vol 50 (1) ◽  
pp. 256-257
Author(s):  
Tai D. Nguyen ◽  
Ronald Gronsky ◽  
Jeffrey B. Kortright
Keyword(s):  
Layered Structure ◽  
Driving Force ◽  
High Energy ◽  
Superior Performance ◽  
In Situ Tem ◽  
Rayleigh Instability ◽  
Practical Applications ◽  
Transmission Electron ◽  
Diffraction Patterns

Nanometer period Ru/C multilayers are one of the prime candidates for normal incident reflecting mirrors at wavelengths < 10 nm. Superior performance, which requires uniform layers and smooth interfaces, and high stability of the layered structure under thermal loadings are some of the demands in practical applications. Previous studies however show that the Ru layers in the 2 nm period Ru/C multilayer agglomerate upon moderate annealing, and the layered structure is no longer retained. This agglomeration and crystallization of the Ru layers upon annealing to form almost spherical crystallites is a result of the reduction of surface or interfacial energy from die amorphous high energy non-equilibrium state of the as-prepared sample dirough diffusive arrangements of the atoms. Proposed models for mechanism of thin film agglomeration include one analogous to Rayleigh instability, and grain boundary grooving in polycrystalline films. These models however are not necessarily appropriate to explain for the agglomeration in the sub-nanometer amorphous Ru layers in Ru/C multilayers. The Ru-C phase diagram shows a wide miscible gap, which indicates the preference of phase separation between these two materials and provides an additional driving force for agglomeration. In this paper, we study the evolution of the microstructures and layered structure via in-situ Transmission Electron Microscopy (TEM), and attempt to determine the order of occurence of agglomeration and crystallization in the Ru layers by observing the diffraction patterns.

Epitaxial growth manner and structure of superconducting oxide films

1990 ◽  
Vol 48 (4) ◽  
pp. 2-3
Author(s):  
Yoshichika Bando ◽  
Takahito Terashima ◽  
Kenji Iijima ◽  
Kazunuki Yamamoto ◽  
Kazuto Hirata ◽  
...  
Keyword(s):  
Ultrathin Films ◽  
Film Surface ◽  
High Energy ◽  
Epitaxial Films ◽  
Layer By Layer ◽  
Initial Growth ◽  
In Situ Growth ◽  
High Quality ◽  
Activated Reactive Evaporation

The high quality thin films of high-Tc superconducting oxide are necessary for elucidating the superconducting mechanism and for device application. The recent trend in the preparation of high-Tc films has been toward “in-situ” growth of the superconducting phase at relatively low temperatures. The purpose of “in-situ” growth is to attain surface smoothness suitable for fabricating film devices but also to obtain high quality film. We present the investigation on the initial growth manner of YBCO by in-situ reflective high energy electron diffraction (RHEED) technique and on the structural and superconducting properties of the resulting ultrathin films below 100Å. The epitaxial films have been grown on (100) plane of MgO and SrTiO, heated below 650°C by activated reactive evaporation. The in-situ RHEED observation and the intensity measurement was carried out during deposition of YBCO on the substrate at 650°C. The deposition rate was 0.8Å/s. Fig. 1 shows the RHEED patterns at every stage of deposition of YBCO on MgO(100). All the patterns exhibit the sharp streaks, indicating that the film surface is atomically smooth and the growth manner is layer-by-layer.

Transmission Electron Microscopy of Epitaxial silicides grown by ultra high vacuum deposition

1989 ◽  
Vol 47 ◽  
pp. 462-463
Author(s):  
D. Loretto ◽  
J. M. Gibson ◽  
S. M. Yalisove
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Electron Diffraction ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Ex Situ ◽  
Transmission Electron

The silicides CoSi2 and NiSi2 are both metallic with the fee flourite structure and lattice constants which are close to silicon (1.2% and 0.6% smaller at room temperature respectively) Consequently epitaxial cobalt and nickel disilicide can be grown on silicon. If these layers are formed by ultra high vacuum (UHV) deposition (also known as molecular beam epitaxy or MBE) their thickness can be controlled to within a few monolayers. Such ultrathin metal/silicon systems have many potential applications: for example electronic devices based on ballistic transport. They also provide a model system to study the properties of heterointerfaces. In this work we will discuss results obtained using in situ and ex situ transmission electron microscopy (TEM).In situ TEM is suited to the study of MBE growth for several reasons. It offers high spatial resolution and the ability to penetrate many monolayers of material. This is in contrast to the techniques which are usually employed for in situ measurements in MBE, for example low energy electron diffraction (LEED) and reflection high energy electron diffraction (RHEED), which are both sensitive to only a few monolayers at the surface.

Electron and ion irradiation-induced dissolution of mechanical twins in the intermetalic U3Si: An in situ HVEM study

1989 ◽  
Vol 47 ◽  
pp. 652-653
Author(s):  
Charles W. Allen ◽  
Robert C. Birtcher
Keyword(s):  
Elevated Temperatures ◽  
Ion Irradiation ◽  
Ion Beam ◽  
National Laboratory ◽  
Argonne National Laboratory ◽  
Heavy Ion ◽  
High Energy ◽  
Mechanical Twinning ◽  
In Situ Experiments

The uranium silicides, including U3Si, are under study as candidate low enrichment nuclear fuels. Ion beam simulations of the in-reactor behavior of such materials are performed because a similar damage structure can be produced in hours by energetic heavy ions which requires years in actual reactor tests. This contribution treats one aspect of the microstructural behavior of U3Si under high energy electron irradiation and low dose energetic heavy ion irradiation and is based on in situ experiments, performed at the HVEM-Tandem User Facility at Argonne National Laboratory. This Facility interfaces a 2 MV Tandem ion accelerator and a 0.6 MV ion implanter to a 1.2 MeV AEI high voltage electron microscope, which allows a wide variety of in situ ion beam experiments to be performed with simultaneous irradiation and electron microscopy or diffraction.At elevated temperatures, U3Si exhibits the ordered AuCu3 structure. On cooling below 1058 K, the intermetallic transforms, evidently martensitically, to a body-centered tetragonal structure (alternatively, the structure may be described as face-centered tetragonal, which would be fcc except for a 1 pet tetragonal distortion). Mechanical twinning accompanies the transformation; however, diferences between electron diffraction patterns from twinned and non-twinned martensite plates could not be distinguished.

Modifications of a JEOL 2000EX TEM for insSitu surface studies

1993 ◽  
Vol 51 ◽  
pp. 640-641
Author(s):  
Michael T. Marshall ◽  
Xianghong Tong ◽  
J. Murray Gibson
Keyword(s):  
Electron Diffraction ◽  
Surface Science ◽  
Film Growth ◽  
High Vacuum ◽  
High Energy ◽  
Energy Electron ◽  
Ultra High Vacuum ◽  
Transmission Electron ◽  
Fundamental Insight

We have modified a JEOL 2000EX Transmission Electron Microscope (TEM) to allow in-situ ultra-high vacuum (UHV) surface science experiments as well as transmission electron diffraction and imaging. Our goal is to support research in the areas of in-situ film growth, oxidation, and etching on semiconducter surfaces and, hence, gain fundamental insight of the structural components involved with these processes. The large volume chamber needed for such experiments limits the resolution to about 30 Å, primarily due to electron optics. Figure 1 shows the standard JEOL 2000EX TEM. The UHV chamber in figure 2 replaces the specimen area of the TEM, as shown in figure 3. The chamber is outfitted with Low Energy Electron Diffraction (LEED), Auger Electron Spectroscopy (AES), Residual Gas Analyzer (RGA), gas dosing, and evaporation sources. Reflection Electron Microscopy (REM) is also possible. This instrument is referred to as SHEBA (Surface High-energy Electron Beam Apparatus).The UHV chamber measures 800 mm in diameter and 400 mm in height. JEOL provided adapter flanges for the column.

scholarly journals A Hybrid Artificial Intelligence Model to Predict the Elastic Behavior of Sandstone Rocks

2019 ◽  
Vol 11 (19) ◽  
pp. 5283 ◽  
Author(s):  
Gowida ◽  
Moussa ◽  
Elkatatny ◽  
Ali
Keyword(s):  
Poisson’S Ratio ◽  
Accurate Determination ◽  
Oil And Gas Industry ◽  
Poisson's Ratio ◽  
Elastic Behavior ◽  
Percentage Error ◽  
Ann Model ◽  
Field Development ◽  
Well Completion

Rock mechanical properties play a key role in the optimization process of engineering practices in the oil and gas industry so that better field development decisions can be made. Estimation of these properties is central in well placement, drilling programs, and well completion design. The elastic behavior of rocks can be studied by determining two main parameters: Young’s modulus and Poisson’s ratio. Accurate determination of the Poisson’s ratio helps to estimate the in-situ horizontal stresses and in turn, avoid many critical problems which interrupt drilling operations, such as pipe sticking and wellbore instability issues. Accurate Poisson’s ratio values can be experimentally determined using retrieved core samples under simulated in-situ downhole conditions. However, this technique is time-consuming and economically ineffective, requiring the development of a more effective technique. This study has developed a new generalized model to estimate static Poisson’s ratio values of sandstone rocks using a supervised artificial neural network (ANN). The developed ANN model uses well log data such as bulk density and sonic log as the input parameters to target static Poisson’s ratio values as outputs. Subsequently, the developed ANN model was transformed into a more practical and easier to use white-box mode using an ANN-based empirical equation. Core data (692 data points) and their corresponding petrophysical data were used to train and test the ANN model. The self-adaptive differential evolution (SADE) algorithm was used to fine-tune the parameters of the ANN model to obtain the most accurate results in terms of the highest correlation coefficient (R) and the lowest mean absolute percentage error (MAPE). The results obtained from the optimized ANN model show an excellent agreement with the laboratory measured static Poisson’s ratio, confirming the high accuracy of the developed model. A comparison of the developed ANN-based empirical correlation with the previously developed approaches demonstrates the superiority of the developed correlation in predicting static Poisson’s ratio values with the highest R and the lowest MAPE. The developed correlation performs in a manner far superior to other approaches when validated against unseen field data. The developed ANN-based mathematical model can be used as a robust tool to estimate static Poisson’s ratio without the need to run the ANN model.

Sign in / Sign up

Export Citation Format

Share Document