scholarly journals Heat Carbonization and ZnCl2 Functionalization of Date Stone as an Adsorbent: Optimization of Material Fabrication Parameters and Adsorption Studies

2021 ◽  
Author(s):  
Nesrine Abderrahim ◽  
Ibtissem Boumnijel ◽  
Hédi Ben Amor ◽  
Ridha Djellabi
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Environmental Remediation ◽  
Diffusion Control ◽  
Maximum Adsorption Capacity ◽  
Scanning Calorimetry ◽  
Activation Temperature ◽  
Synthesis Conditions ◽  
Fabrication Parameters

Abstract The scientific community gave a lot attention to prepare adsorbents from different natural agriculture-based materials to be used alternative to commercial activated carbon. However, less studies on the optimization of fabrication parameters to obtain activated carbon with highly surface area and adsorption capacity. Herein, we report the synthesis conditions optimization of adsorbent based on date stone and modified with ZnCl2. To obtain a highly adsorption ability of the materials, three systematic parameters were evaluated such as the activation temperature, activation time and the functionalization ratio by ZnCl2. The optimization study showed that the best factors to fabricate an adsorbent from date stone are 700°C, 120 min and 2.0 (g/g), wherein, the specific surface area was found to be 1036 m2/g. While, the iodine and phenol numbers were 928.5 mg/g and 2.1 mmol/g, respectively. To further understand the effect of synthesis parameters, the raw and the as-synthesized activated carbon were characterized via Fourier transmission infrared spectroscopy (FT-IR), X-ray diffraction (XRD), differential thermal analysis (DTA) and differential scanning calorimetry (DSC). Batch sorption tests to remove MB from water showed a maximum adsorption capacity of 384.6 mg/g using the prepared activated carbon at pH 6 and room temperature (25±2 °C). It was found also that the kinetic adsorption data obeyed the pseudo-second order and, both external diffusion and intra-particle diffusion control the adsorption. Based on the obtained results, the optimization of synthesis conditions through experimental and mobilization studies may help the transfer of technology in terms of agriculture-based materials valorisation towards the environmental remediation.

scholarly journals ADSORPSI ZAT WARNA METILEN BIRU DENGAN KARBON AKTIF DARI KULIT DURIAN MENGGUNAKAN KOH DAN NaOH SEBAGAI AKTIVATOR

2017 ◽  
Vol 6 (1) ◽  
pp. 49-55 ◽  
Author(s):  
Farida Hanum ◽  
Rikardo Jgst Gultom ◽  
Maradona Simanjuntak
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Contact Time ◽  
Wavelength Region ◽  
Second Order ◽  
Carbon Surface ◽  
Maximum Adsorption Capacity ◽  
Activation Process ◽  
Maximum Surface

Durian is a kind of tropical fruits which can grow well in Indonesia. Durian is containing 60-75% shell. Durian shell could be a potential alternative to activated carbon because it contains 57.42% carbon. The aim of this research is to know the effect of contact time and  stirring speed to activated carbon adsorption capacity from durian shell with KOH and NaOH as activators. FTIR (Fourier Transform Infra Red) analysis showed the activation process effects on  absorption intensity  wavelength region and resulted in formation of C = C aromatic tape, so that the nature of the charcoal becomes more polar compared with the initial condition. Analysis using spectrophotometer UV-Vis to determine  absorbance and  final concentration of each variation of contact time and stirring speed. The results showed that the maximum adsorption capacity obtained by activation of KOH and NaOH on stirring speed of 150 rpm and a contact time of 90 minutes is equal to 3.92 mg / g and 3.8 mg / g respectively. The maximum surface area obtained by activation of KOH and NaOH during the stirring speed 130 rpm and a contact time of 120 minutes is equal to 1785.263 m2 / g and 1730.332 m2 / g respectively. The maximum surface area obtained from this research has met the standards of commercial activated carbon surface area was between 800-1800 m2/ g. Modeling pseudo second order presents a more representative adsorption data, a second order equation is based on the assumption that adsorption step is chemosorption.

scholarly journals Effect of activated carbons from rubber seed shell on Crystal Violet removal

2020 ◽  
Vol 22 (1) ◽  
pp. 43-54 ◽  
Author(s):  
B. Anegbe ◽  
R.C. Emeribe ◽  
J.M. Okuo
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Crystal Violet ◽  
Optimum Concentration ◽  
Batch Adsorption ◽  
Maximum Adsorption Capacity ◽  
Rubber Seed ◽  
Adsorbent Dose

Dyes are complex organic compounds which are used by various industries to add colour to their products. Water bodies are polluted when these industries dispose their effluents to the environment. In this study, powdered activated carbon was prepared from rubber seed shells (RSS) and was employed in the removal of crystal violet from aqueous solution. The rubber seed shell was first activated using ammonium chloride, shared into two portions and was carbonized at 500 and 300o C respectively. They were characterized in terms of bulk density, ash and moisture contents, surface area and IR Spectroscopy. Batch adsorption process which involved the use of these rubber seed shells was employed in the removal of crystal violet from aqueous solution. The effect of contact time, adsorbent dose, pH and dye concentration were investigated. The results showed that o maximum adsorption capacity of 500 C carbonized rubber seed shell was 97.93 % at 75 mins. The adsorbent dose, pH and optimum concentration were respectively 5.0 g, 10 and 10 mg/l. The maximum adsorption  capacity of 300o C carbonized rubber seed shell was 96.73 % at 30 mins with an adsorbent dose of 5.0 g; pH of 10 and optimum concentration of 10 mg/l. The experimental data obtained were fitted into Freundlich,Langmuir, Temkin and Frumkin adsorption isotherms and was found to fit into the four isotherms. However,  the rubber seed shell carbonized at 500o C was found to be more effective in the removal of crystal violet from o aqueous solution than that carbonized at 300o C. This might probably be due to the larger surface area. Keywords: Activated Carbon, Rubber Seed Shell and Crystal Violet

Analisis Variasi Temperatur Aktivasi Terhadap Daya Serap Arang Aktif Tandan Aren (Arenga Pinnata Merr) Dengan Agen Aktivasi Potassium Silicate(K2SiO3)

2020 ◽  
Vol 5 (3) ◽  
pp. 221
Author(s):  
Muhammad Azam ◽  
Muhammad Anas ◽  
Erniwati Erniwati
Keyword(s):  
Methylene Blue ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Temperature Variation ◽  
Chemical Activation ◽  
Weight Ratio ◽  
Potassium Silicate ◽  
Physical Activation ◽  
Activation Temperature ◽  
Pyrolysis Reactor

This study aims to determine the effect of variation of activation temperature of activated carbon from sugar palm bunches of chemically activatied with the activation agent of potassium silicate (K2SiO3) on the adsorption capacity of iodine and methylene blue. Activated carbon from bunches of sugar palmacquired in four steps: preparationsteps, carbonizationstepsusing the pyrolysis reactor with temperature of 300 oC - 400 oC for 8 hours and chemical activation using of potassium silicate (K2SiO3) activator in weight ratio of 2: 1 and physical activation using the electric furnace for 30 minutes with temperature variation of600 oC, 650 oC, 700 oC, 750 oC and 800 oC. The iodine and methyleneblue adsorption testedby Titrimetric method and Spectrophotometry methodrespectively. The results of the adsorption of iodine and methylene blue activated carbon from sugar palm bunches increased from 240.55 mg/g and 63.14 mg/g at a temperature of 600 oC to achieve the highest adsorption capacity of 325.80 mg/g and 73.59 mg/g at temperature of 700 oC and decreased by 257.54 mg/g and 52.03 mg/g at a temperature of 800 oCrespectively.However, it does not meet to Indonesia standard (Standard Nasional Indonesia/SNI), which is 750 mg/g and 120 mg/g respectively.

Study of the Porous Structure and High Adsorption Capacity of Biomass-Based Activated Carbon Prepared from Aspen Wood by Ferric Nitrate III Activation

2021 ◽  
Vol 15 (2) ◽  
pp. 131-144
Author(s):  
Chunjiang Jin ◽  
Huimin Chen ◽  
Luyuan Wang ◽  
Xingxing Cheng ◽  
Donghai An ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Mass Ratio ◽  
Aspen Wood ◽  
Surface Functional Groups ◽  
Wood Sawdust

In this study, aspen wood sawdust was used as the raw material, and Fe(NO3)3 and CO2 were used as activators. Activated carbon powder (ACP) was produced by the one-step physicochemical activation method in an open vacuum tube furnace. The effects of different mass ratios of Fe(NO3)3 and aspen wood sawdust on the pore structure of ACP were examined under single-variable experimental conditions. The mass ratio was 0–0.4. The detailed characteristics of ACP were examined by nitrogen adsorption, scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. The adsorption capacity of ACP was established by simulating volatile organic compounds (VOCs) using ethyl acetate. The results showed that ACP has a good nanostructure with a large pore volume, specific surface area, and surface functional groups. The pore volume and specific surface area of Fe-AC-0.3 were 0.26 cm3/g and 455.36 m2/g, respectively. The activator played an important role in the formation of the pore structure and morphology of ACP. When the mass ratio was 0–0.3, the porosity increased linearly, but when it was higher than 0.3, the porosity decreased. For example, the pore volume and specific surface area of Fe-AC-0.4 reached 0.24 cm3/g and 430.87 m2/g, respectively. ACP presented good VOC adsorption performance. The Fe-AC-0.3 sample, which contained the most micropore structures, presented the best adsorption capacity for ethyl acetate at 712.58 mg/g. Under the action of the specific reaction products nitrogen dioxide (NO2) and oxygen, the surface of modified ACP samples showed different rich C/O/N surface functional groups, including C-H, C=C, C=O, C-O-C, and C-N.

scholarly journals Development of Activated Carbon Using One Step Carbonization and Activation Reaction by Polymer Blend Method

2015 ◽  
Vol 57 ◽  
pp. 156-162 ◽  
Author(s):  
S. Manocha ◽  
Parth Joshi ◽  
Amit Brahmbhatt ◽  
Amiya Banerjee ◽  
Snehasis Sahoo ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Surface Characteristics ◽  
Nitrogen Atmosphere ◽  
Activation Process ◽  
Average Pore ◽  
Activation Temperature ◽  
Optimum Synthesis ◽  
Different Temperatures ◽  
One Step

In the present work, a one step carbon activation process was developed by stabilized poly-blend. It is carbonized in nitrogen atmosphere and activated in steam in one step for known interval of times to enhance the surface area and develop interconnected porosity. The weight-loss behavior during steam activation of stabilized poly-blend at different temperatures, surface area and pore size distribution were studied to identify the optimum synthesis parameters. The results of surface characteristics were compared with those of activated carbon prepared by carbonization and activation in two steps. It was found that activation temperature has profound effect on surface characteristics. As activation temperature was raised from 800 °C to 1150 °C, surface area of activated carbon increased about three times. In addition to surface area, average pore diameter also increases with increasing activation temperature. Thus, activated carbon with high percentage of porosity and surface area can be developed by controlling the activation temperature during activation process.

scholarly journals STUDI ADSORPSI ZAT WARNA NAPHTHOL YELLOW S PADA LIMBAH CAIR MENGGUNAKAN KARBON AKTIF DARI AMPAS TEBU

Jurnal Kimia ◽  
2019 ◽  
Vol 13 (1) ◽  
pp. 104
Author(s):  
W. P. Utoo1 ◽  
E. Santoso ◽  
G. Yuhaneka ◽  
A. I. Triantini ◽  
M. R. Fatqi ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Contact Time ◽  
Adsorption Process ◽  
Activation Process ◽  
Adsorption Model ◽  
High Adsorption ◽  
Prolonged Contact ◽  
Test Result

The aim of this research is to get activated carbon from sugarcane bagasse with high adsorption capacity to Naphthol Yellow S and to know factors influencing the adsorption capacity. Activated carbon is prepared by incomplete combustion of sugracane bagasse. The resulting carbon is activated with H2SO4 with concentration variation of 0.5; 1.0; 1.5 and 2.0 M and is continued by calcination at 400 °C. The measurement of the surface area of ??activated carbon by the methylene blue method indicates that the activation process successfully extends the surface area of carbon from 31.87 m2/g before activation to 66-72 m2/g after activation. Activated carbon with concentration of 2.0 M H2SO4 showed the highest surface area of ??71.85 m2/g, however, the best adsorption was shown by activated carbon with a concentration of 0.5 M H2SO4 with the adsorption capacity of 83.93%. The adsorption test showed that the best amount of adsorbent was 0.2 g with contact time for 30 minutes. Prolonged contact time can decrease the amount of Naphthol Yellow S adsorbed. The best adsorption test result was shown by sample with activator concentration of 0,5 M, mass of 0,2 g and contact time of 30 min with adsorption capacity 95,81% or amount of dye adsorbed equal to 143,72 mg/g. The adsorption study also showed that the entire Naphthol Yellow S adsorption process followed the Langmuir isothemal adsorption model. Qualitative testing of real batik waste indicates that activated carbon can reduce the dyes waste containing Naphthol Yellow Sexhibited by the color of batik waste which is more faded.  

scholarly journals Pinecone-Derived Activated Carbons as an Effective Medium for Hydrogen Storage

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2237
Author(s):  
Sara Stelitano ◽  
Giuseppe Conte ◽  
Alfonso Policicchio ◽  
Alfredo Aloise ◽  
Giovanni Desiderio ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Hydrogen Storage ◽  
Adsorption Capacity ◽  
Surface Area ◽  
Hydrogen Adsorption ◽  
Activated Carbons ◽  
Chemical Activation ◽  
Textural Properties ◽  
Biomass Waste ◽  
Wavelength Dispersive Spectrometry

Pinecones, a common biomass waste, has an interesting composition in terms of cellulose and lignine content that makes them excellent precursors in various activated carbon production processes. The synthesized, nanostructured, activated carbon materials show textural properties, a high specific surface area, and a large volume of micropores, which are all features that make them suitable for various applications ranging from the purification of water to energy storage. Amongst them, a very interesting application is hydrogen storage. For this purpose, activated carbon from pinecones were prepared using chemical activation with different KOH/precursor ratios, and their hydrogen adsorption capacity was evaluated at liquid nitrogen temperatures (77 K) at pressures of up to 80 bar using a Sievert’s type volumetric apparatus. Regarding the comprehensive characterization of the samples’ textural properties, the measurement of the surface area was carried out using the Brunauer–Emmett–Teller method, the chemical composition was investigated using wavelength-dispersive spectrometry, and the topography and long-range order was estimated using scanning electron microscopy and X-ray diffraction, respectively. The hydrogen adsorption properties of the activated carbon samples were measured and then fitted using the Langmuir/ Töth isotherm model to estimate the adsorption capacity at higher pressures. The results showed that chemical activation induced the formation of an optimal pore size distribution for hydrogen adsorption centered at about 0.5 nm and the proportion of micropore volume was higher than 50%, which resulted in an adsorption capacity of 5.5 wt% at 77 K and 80 bar; this was an increase of as much as 150% relative to the one predicted by the Chahine rule.

scholarly journals Evaluation of alkaline-based activated carbon from Leucaena Leucocephala produced at different activation temperatures for cadmium adsorption

2020 ◽  
Vol 11 (1) ◽  
Author(s):  
Wan Muhammad Hilmi Wan Ibrahim ◽  
Mohd Hazim Mohamad Amini ◽  
Nurul Syuhada Sulaiman ◽  
Wan Rasidah Wan Abdul Kadir
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Leucaena Leucocephala ◽  
Heavy Metal Contamination ◽  
High Heat ◽  
Raw Material ◽  
Activation Temperature ◽  
Promising Alternative ◽  
Alternative Material ◽  
The Cost

AbstractHeavy metal contamination in water is happening worldwide. Adsorption using activated carbon is a common choice for cleaning the wastewater. The drawback of activated carbon is the higher cost of production due to the need for high heat in the process. This work investigated on activated carbon produced from the abundantly available Leucaena leucocephala biomass in order to reduce the cost of raw material. The biomass was chemically activated at different activation temperatures. The produced activated carbon was characterized using SEM, FT-IR, surface analyzer, and TGA. Isothermic and thermodynamic studies were done to evaluate the adsorption properties of the activated carbon. It was found out that higher surface area can be obtained using the higher activation temperature. Higher NaOH to carbonized sample ratios also resulted in higher surface area for all activation temperatures, which are 662 m2g-1 for 700 °C activation temperature, 735 m2g-1 for 750 °C, and 776 m2g−1 for 800 °C. Isothermic studies showed that all of the activated carbon that is produced from Leucaena leucocephala biomass are fit to the Langmuir isotherm, regardless of any activation temperature. Lastly, the thermodynamic study found out the adsorption process is endothermic, reflected by the positive value of ΔHo. It can be concluded that Leucaena leucocephala is a promising alternative material for producing activated carbon.

scholarly journals Massaranduba Sawdust: A Potential Source of Charcoal and Activated Carbon

Polymers ◽  
2019 ◽  
Vol 11 (8) ◽  
pp. 1276 ◽  
Author(s):  
Castro ◽  
Nobre ◽  
Napoli ◽  
Bianchi ◽  
Moulin ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Surface Area ◽  
Value Added ◽  
High Reactivity ◽  
Large Surface Area ◽  
Scanning Calorimetry ◽  
Co2 Gas ◽  
Heat Treated ◽  
Amorphous Structures ◽  
Adsorption Desorption

This paper provides proof of concept that activated carbon (AC) may be readily produced using limited conversion methods and resources from sawdust of massaranduba (Manilkara huberi) wood, thereby obtaining value-added products. Sawdust was sieved and heat-treated in an oxygen-free muffle furnace at 500 °C to produce charcoal. The charcoal was activated in a tubular electric furnace at 850 °C while being purged with CO2 gas. Microstructural, thermal and physical properties of the three components: sawdust, charcoal and AC were compared by means of field emission scanning electron microscopy (FESEM), X-ray diffractometry (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), density and water adsorption/desorption measurements. The resulting AC had a large surface area as measured by Brunauer-Emmett-Teller (BET) comparable to other such values found in the literature. The large surface area was due to pore development at the microstructural level as shown by FESEM. XRD illustrated that sawdust had a semi-crystalline structure whereas charcoal and AC evidenced mostly amorphous structures. TGA and DSC showed that AC had high reactivity to moisture compared to sawdust and charcoal.

Application of Carbonaceous Materials to Phenol Removal from Aqueous Solution by Adsorption

2012 ◽  
Vol 164 ◽  
pp. 297-301 ◽  
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Qing Chao Gong ◽  
Cun Cun Chen ◽  
Cai Hong Zheng ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Petroleum Coke ◽  
Granular Activated Carbon ◽  
Powdered Activated Carbon ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Carbonaceous Materials ◽  
Solution Ph ◽  
Equilibrium Studies

Low cost carbonaceous materials were evaluated for their ability to remove phenol from wastewater. The effects of adsorbents dosage, contact time and maximum adsorption capacity were investigated for granular activated carbon, powdered activated carbon, petroleum coke and multi-walled carbon nanotube (MWNT). Equilibrium studies were conducted in 50mg/L initial phenol concentration, solution pH of 5 and at temperature of 23°C. The results showed the adsorption process was fast and it reached equilibrium in 3 h. Petroleum coke and MWNT had poor adsorption which could reach the removal efficiency of phenol with 43.18% and 36.64% respectively. The granular activated carbon possessed good adsorption ability to phenol with 96.40% at the optimum dosage 5g and optimum time 90min.The powdered activated carbon was an effective adsorbent with a maximum adsorption capacity of 42.32 mg/g.

Sign in / Sign up

Export Citation Format

Share Document