Characterization and Failure Analysis of 3D Integrated Semiconductor Devices—Novel Tools for Fault Isolation, Target Preparation and High Resolution Material Analysis

2010 ◽  
Author(s):  
Frank Altmann ◽  
Matthias Petzold ◽  
Christian Schmidt ◽  
Roland Salzer ◽  
Cathal Cassidy ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Flip Chip ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
High Rate ◽  
Target Preparation ◽  
Integrated Devices ◽  
Analysis Workflow ◽  
Silicon Vias

Abstract In this paper we will introduce novel methodical approaches for material and failure analysis of 3D integrated devices. The potential and advantages of the new concepts and tools will be demonstrated for flip-chip-like interconnects but in addition, for the first time, for Through Silicon Vias (TSV). The employed techniques combine non-destructive fault localization with efficient and accurate target preparation to get access for following microstructure diagnostics, forming a subsequent failure analysis workflow. The concept presented here involves the application of improved Lock-In Thermography (LIT), and three different innovative concepts of high rate Focused Ion Beam (FIB) techniques.

Silicon and Package Preparation Options for Focused Ion Beam (FIB) Circuit Editing and General Packaging Failure Analysis

2013 ◽  
Author(s):  
Steven B. Herschbein ◽  
Carmelo F. Scrudato ◽  
George K. Worth ◽  
Edward S. Hermann
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Focused Ion Beam ◽  
Solder Bump ◽  
Ion Beam ◽  
Full Thickness ◽  
Wire Bond ◽  
Signal Probe ◽  
Silicon Vias ◽  
Semiconductor Packaging

Abstract The Focused Ion Beam (FIB) technique of internal modification for chip repair, layout verification, and internal signal probe access has become an integral part of the process for bringing advanced products to market. The pervasive switch from wire bond connections to single component flipchip solder bump mounting on high value products has greatly aided the task of FIB editing by placing the bare backside silicon of the die within easy reach. FIB chip circuit access begins with task-specific sample preparation. The package opening and silicon prep process is well defined and quite robust when full thickness chips are mounted to simple ceramic carriers. Unfortunately, the introduction of flexible organic laminate substrates and the development of stacked die packaging has further complicated the process. Multi-chip packages containing combinations of full thickness and thinned chips may be present. They could be wire-bond connected, or use Through-Silicon Vias (TSV) for double sided attachment. Multiple heat treatment cycles joining together materials with vastly different coefficients of thermal expansion (CTE) may result in severe package warpage and stress. All of these conditions and possible combinations have served to invalidate key elements of the established sample preparation process, and made each presented case unique. As the FIB team works to develop new precision techniques for internal circuitry access, the greater semiconductor packaging development and failure analysis community has benefited from the introduction of new tooling and methodologies.

Application of Focused Ion Beam System as A Defect Localization and Root Cause Analysis Tool

2001 ◽  
Author(s):  
C.C. Ooi ◽  
K.H. Siek ◽  
K.S. Sim
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
Analysis Tool ◽  
Root Cause ◽  
Beam System ◽  
Defect Localization ◽  
Challenging Environment ◽  
Microprocessor Technology

Abstract Focused ion beam system has been widely used as a critical failure analysis tool as microprocessor technology advances at a ramping speed. It has become an essential step in failure analysis to reveal physical defects post electrical fault isolation. In this highly competitive and challenging environment prevalent today, failure analysis throughput time is of utmost important. Therefore quick, efficient and reliable physical failure analysis technique is needed to avoid potential issues from becoming bigger. This paper will discuss the applications of FIB as a defect localization and root cause determination tool through the passive charge contrast technique and pattern FIB analysis.

Failure Analysis Work Flow for Electrical Shorts in Triple Stacked 3D TSV Daisy Chains

2015 ◽  
Vol 2015 (1) ◽  
pp. 000469-000473 ◽  
Author(s):  
J. Gaudestad ◽  
A. Orozco ◽  
I. De Wolf ◽  
T. Wang ◽  
T. Webers ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
Root Cause ◽  
Current Path ◽  
Dual Beam ◽  
Resolution Imaging ◽  
Magnetic Field Imaging ◽  
Non Destructive

In this paper we show an efficient workflow that combines Magnetic Field Imaging (MFI) and Dual Beam Plasma Focused Ion Beam (DB-PFIB) for fast and efficient Fault Isolation and root cause analysis in 2.5/3D devices. The work proves MFI is the best method for Electric Fault Isolation (EFI) of short failures in 2.5/3D Through Silicon Via (TSV) triple stacked devices in a true non-destructive way by imaging the current path. To confirm the failing locations and to do Physical Failure Analysis (PFA), a DB-PFIB system was used for cross sectioning and volume analysis of the TSV structures and high resolution imaging of the identified defects. With a DB-PFIB, the fault is exposed and analyzed without any sample prep artifacts seen in mechanical polishing or laser preparation techniques and done in a considerably shorter amount of time than that required when using a traditional Gallium Focused Ion Beam (FIB).

scholarly journals Die Backside FIB Preparation for Identification and Characterization of Metal Voids

1999 ◽  
Author(s):  
Ann N. Campbell ◽  
William F. Filter ◽  
Nicholas Antoniou
Keyword(s):  
Integrated Circuits ◽  
Failure Analysis ◽  
Cross Sections ◽  
Integrated Circuit ◽  
Flip Chip ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Milling Process ◽  
Plan View ◽  
Metal Interconnects

Abstract Both the increased complexity of integrated circuits, resulting in six or more levels of integration, and the increasing use of flip-chip packaging have driven the development of integrated circuit (IC) failure analysis tools that can be applied to the backside of the chip. Among these new approaches are focused ion beam (FIB) tools and processes for performing chip edits/repairs from the die backside. This paper describes the use of backside FIB for a failure analysis application rather than for chip repair. Specifically, we used FIB technology to prepare an IC for inspection of voided metal interconnects (“lines”) and vias. Conventional FIB milling was combined with a superenhanced gas assisted milling process that uses XeF2 for rapid removal of large volumes of bulk silicon. This combined approach allowed removal of the TiW underlayer from a large number of M1 lines simultaneously, enabling rapid localization and plan view imaging of voids in lines and vias with backscattered electron (BSE) imaging in a scanning electron microscope (SEM). Sequential cross sections of individual voided vias enabled us to develop a 3D reconstruction of these voids. This information clarified how the voids were formed, helping us identify the IC process steps that needed to be changed.

Failure Analysis of Flip Chip C4 Package Using Focused Ion Beam Milling Technique

2011 ◽  
Author(s):  
Lihong Cao ◽  
Loc Tran ◽  
Wallace Donna
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Cross Sections ◽  
Flip Chip ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Failure Mechanisms ◽  
Organic Substrate ◽  
Dual Beam ◽  
Preparation Techniques

Abstract This article describes how Focused Ion Beam (FIB) milling methodology enhances the capability of package-level failure analysis on flip-chip packages by eliminating the artifacts induced by using conventional mechanical techniques. Dual- Beam Focused Ion Beam (DB FIB) cross sections were successful in detecting failure mechanisms related either to the die/C4 bump or package defect inside the organic substrate. This paper outlines detailed sample preparation techniques prior to performing the DB FIB cross-sections, along with case studies of DB FIB cross-sections.

Defect Localization and Root Cause Analysis on e-Fuse Read Reliability Failure

2014 ◽  
Author(s):  
Hung Chin Chen ◽  
Chih Yang Tsai ◽  
Shih Yuan Liu ◽  
Yu Pang Chang ◽  
Jian Chang Lin
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Metal Layer ◽  
Ion Beam ◽  
Fault Isolation ◽  
Resistance Change ◽  
Cause Analysis ◽  
Root Cause ◽  
Failure Location ◽  
Rate Of Failure

Abstract Fault isolation is the most important step for Failure Analysis (FA), and it is closely linked with the success rate of failure mechanism finding. In this paper, we will introduce a case that hard to debug with traditional FA skills. In order to find out its root cause, several advanced techniques such as layout tracing, circuit edit and Infrared Ray–Optical Beam Induced Resistance Change (IR-OBIRCH) analysis had been applied. The circuit edit was performed following layout tracing for depositing probing pads by Focused Ion Beam (FIB). Then, IR-OBIRCH analysis with biasing on the two FIB deposited probing pads and a failure location was detected. Finally, the root cause of inter- metal layer bridge was found in subsequent physical failure analysis.

Failure Analysis Work Flow for Electrical Shorts in Triple Stacked 3D TSV Daisy Chains

2014 ◽  
Author(s):  
J. Gaudestad ◽  
A. Orozco ◽  
I. De Wolf ◽  
T. Wang ◽  
T. Webers ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Fault Isolation ◽  
Root Cause ◽  
Current Path ◽  
Dual Beam ◽  
Resolution Imaging ◽  
Magnetic Field Imaging ◽  
Non Destructive

Abstract In this paper we show an efficient workflow that combines Magnetic Field Imaging (MFI) and Dual Beam Plasma Focused Ion Beam (DB-PFIB) for fast and efficient Fault Isolation and root cause analysis in 2.5/3D devices. The work proves MFI is the best method for Electric Fault Isolation (EFI) of short failures in 2.5/3D Through Silicon Via (TSV) triple stacked devices in a true non-destructive way by imaging the current path. To confirm the failing locations and to do Physical Failure Analysis (PFA), a DB-PFIB system was used for cross sectioning and volume analysis of the TSV structures and high resolution imaging of the identified defects. With a DB-PFIB, the fault is exposed and analyzed without any sample prep artifacts seen in mechanical polishing or laser preparation techniques and done in a considerably shorter amount of time than that required when using a traditional Gallium Focused Ion Beam (FIB).

Electrical Characterization of Different Failure Modes in Sub-100 nm Devices Using Nanoprobing Technique

2009 ◽  
Author(s):  
E. Hendarto ◽  
S.L. Toh ◽  
J. Sudijono ◽  
P.K. Tan ◽  
H. Tan ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Nickel Silicide ◽  
Fault Isolation ◽  
Technology Nodes ◽  
Scanning Electron

Abstract The scanning electron microscope (SEM) based nanoprobing technique has established itself as an indispensable failure analysis (FA) technique as technology nodes continue to shrink according to Moore's Law. Although it has its share of disadvantages, SEM-based nanoprobing is often preferred because of its advantages over other FA techniques such as focused ion beam in fault isolation. This paper presents the effectiveness of the nanoprobing technique in isolating nanoscale defects in three different cases in sub-100 nm devices: soft-fail defect caused by asymmetrical nickel silicide (NiSi) formation, hard-fail defect caused by abnormal NiSi formation leading to contact-poly short, and isolation of resistive contact in a large electrical test structure. Results suggest that the SEM based nanoprobing technique is particularly useful in identifying causes of soft-fails and plays a very important role in investigating the cause of hard-fails and improving device yield.

Direct Plan View FIB Liftout for Near-Surface Defect Analysis in TEM

2013 ◽  
Author(s):  
Max L. Lifson ◽  
Carla M. Chapman ◽  
D. Philip Pokrinchak ◽  
Phyllis J. Campbell ◽  
Greg S. Chrisman ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Silicon Germanium ◽  
Focused Ion Beam ◽  
Surface Defects ◽  
Ion Beam ◽  
Misfit Dislocations ◽  
Tem Analysis ◽  
Plan View ◽  
Near Surface ◽  
Straightforward Method

Abstract Plan view TEM imaging is a powerful technique for failure analysis and semiconductor process characterization. Sample preparation for near-surface defects requires additional care, as the surface of the sample needs to be protected to avoid unintentionally induced damage. This paper demonstrates a straightforward method to create plan view samples in a dual beam focused ion beam (FIB) for TEM studies of near-surface defects, such as misfit dislocations in heteroepitaxial growths. Results show that misfit dislocations are easily imaged in bright-field TEM and STEM for silicon-germanium epitaxial growth. Since FIB tools are ubiquitous in semiconductor failure analysis labs today, the plan view method presented provides a quick to implement, fast, consistent, and straightforward method of generating samples for TEM analysis. While this technique has been optimized for near-surface defects, it can be used with any application requiring plan view TEM analysis.

Fast Turn-around Failure Analysis of Metal Interconnection Using FIB and LA ICP-MS

2010 ◽  
Author(s):  
Zixiao Pan ◽  
Wei Wei ◽  
Fuhe Li
Keyword(s):  
Failure Analysis ◽  
Inductively Coupled Plasma ◽  
Structural Damage ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Detection Sensitivity ◽  
Chemical Contamination ◽  
Inductively Coupled ◽  
Minimal Sample ◽  
Icp Ms

Abstract This paper introduces our effort in failure analysis of a 200 nm thick metal interconnection on a glass substrate and covered with a passivation layer. Structural damage in localized areas of the metal interconnections was observed with the aid of focused ion beam (FIB) cross-sectioning. Laser ablation inductively coupled plasma mass spectroscopy (LA ICP-MS) was then applied to the problematic areas on the interconnection for chemical survey. LA ICP-MS showed direct evidence of localized chemical contamination, which has likely led to corrosion (or over-etching) of the metal interconnection and the assembly failure. Due to the high detection sensitivity of LA ICP-MS and its compatibility with insulating material analysis, minimal sample preparation is required. As a result, the combination of FIB and LA ICP-MS enabled successful meso-scale failure analysis with fast turnaround and reasonable cost.

Sign in / Sign up

Export Citation Format

Share Document