scholarly journals BENDING PROPERTIES OF A FUNCTIONALLY GRADED POLYMERIC COMPOSITE REINFORCED WITH A HYBRID NANOMATERIAL

2021 ◽  
Vol 21 (4) ◽  
pp. 302-319
Author(s):  
Mahdi M. S. Shareef ◽  
Ahmed Naif Al-Khazraji ◽  
Samir Ali Amin
Keyword(s):  
Mechanical Properties ◽  
Volume Fraction ◽  
Functionally Graded ◽  
Hybrid Nanocomposites ◽  
Bending Test ◽  
Fe Model ◽  
Al2o3 Nanoparticles ◽  
Isotropic Layer ◽  
Element Analysis ◽  
Three Point Bending

In this paper, functionally graded polymer hybrid nanocomposites have been produced by silica (SiO2) nanoparticles and alumina (Al2O3) nanoparticles distributed in a matrix of epoxy during the ultra-sonication via hand lay-up method. The variation in nanoparticles volume fraction (Vf.) has been given in the thickness direction for reaching the gradation. Each layer has a thickness of 1.2 mm through various concentrations of nanoparticles and is sequentially cast in acrylic moulds to fabricate the graded composite sheet with a 6 mm thickness. To fabricate the functionally graded layers, various concentrations of different nanoparticles (1.5% SiO2, 1% SiO2, epoxy, 2% Al2O3 and 3% Al2O3) have been used for tensile and compressive testing each isotropic layer of functionally graded material (FGM). The mechanical property that was studied for pure epoxy, isotropic and FGM was the flexural resistance. The flexural properties of FGM, isotropic nanocomposite (1% SiO2 + 2% Al2O3) and pristine epoxy, for evaluating their mechanical properties, including flexural stress-strain criteria and flexural Young's modulus, were determined via a Three-point bending test, with loading from the side of silica and alumina for the hybrid-FGM and at one side for the isotropic hybrid nanocomposite and pristine epoxy. The mechanical properties (tensile and compression) and the density of every layer were obtained for the epoxy resin and nanocomposites. They can benefit from the Finite Element Analysis (FEA) of the Three-point bending test via the Design Modeler (ANSYS workbench). The results of experiments were confirmed via building a detailed 3D FE model. Also, the advanced deformation results from the FE model were found in good agreement with the experimental outcomes.

scholarly journals XFEM based fracture analysis of single notch reactive powder concrete specimen subjected to three point bending test

2020 ◽  
Vol 156 ◽  
pp. 05027
Author(s):  
Patria Kusumaningrum ◽  
Bambang Budiono ◽  
Muhammad Fajar ◽  
Elitha
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Volume Fraction ◽  
Bending Test ◽  
Single Edge ◽  
Three Point Bending ◽  
Single Edge Notch ◽  
Finite Element Software ◽  
Edge Notch ◽  
Reactive Powder

An extended finite element method (XFEM) for fracture problem within the finite element software ABAQUS is adopted in order to investigate the mechanical properties and fracture behaviour of RPC material. The RPC materials observed are plain RPC of 0% and steel fiber RPC (SFRPC) of 2% volume fraction. Single edge notch three-point bending (TPB) tests of RPC materials are performed. The mechanical properties of RPC with respect to single edge notch TPB test, i.e. tensile stress, CMOD, and fracture energy obtained from experiment are then compared to those obtained from numerical analysis. A good agreement is observed between the experimental and numerical results.

scholarly journals On the determination of first-mode stress intensity factors and T-stress in a continuous functionally graded beam using digital image correlation method

2021 ◽  
Vol 9 (1) ◽  
pp. 56-70
Author(s):  
Ahmed M. Abood ◽  
◽  
Haider Khazal ◽  
Abdulkareem F. Hassan
Keyword(s):  
Stress Intensity ◽  
Digital Image Correlation ◽  
Digital Image ◽  
Volume Fraction ◽  
Functionally Graded ◽  
Image Correlation ◽  
Bending Test ◽  
Fe Model ◽  
Functionally Graded Beam ◽  
T Stress

<abstract> <p>In this study, fracture parameters of epoxy/glass functionally graded composite were determined experimentally using the digital image correlation (DIC) method. A functionally graded material (FGM) with continuous variation in elastic properties was manufactured by gravity casting in vertical template. A 30% volume fraction of glass spheres was dispersed in a low viscosity resin. A single edge crack specimen was examined in a three-point bending test under mode Ⅰ loading with cracks along the gradient tendency of the material properties. The mechanical properties of FGM were calculated according to ASTM D638. The DIC technique was adopted to obtain the deformation region around the crack tip. William's series was employed to calculate stress intensity factor and T-stress. The experimental results then verified by solving the FE model using ABAQUS program. The comparison between DIC and numerical results illustrated a largely acceptable achievement.</p> </abstract>

Flexural behavior of functionally graded polymeric composite beams

2021 ◽  
pp. 152808372110003
Author(s):  
M Atta ◽  
A Abu-Sinna ◽  
S Mousa ◽  
HEM Sallam ◽  
AA Abd-Elhady
Keyword(s):  
Flexural Strength ◽  
Volume Fraction ◽  
Stress Gradient ◽  
Polymeric Composite ◽  
Composite Beams ◽  
Functionally Graded ◽  
Flexural Behavior ◽  
Bending Test ◽  
Polymeric Composite Material ◽  
Fiber Volume

The bending test is one of the most important tests that demonstrates the advantages of functional gradient (FGM) materials, thanks to the stress gradient across the specimen depth. In this research, the flexural response of functionally graded polymeric composite material (FGM) is investigated both experimentally and numerically. Fabricated by a hand lay-up manufacturing technique, the unidirectional glass fiber reinforced epoxy composite composed of ten layers is used in the present investigation. A 3-D finite element simulation is used to predict the flexural strength based on Hashin’s failure criterion. To produce ten layers of FGM beams with different patterns, the fiber volume fraction ( Vf%) ranges from 10% to 50%. A comparison between FGM beams and conventional composite beams having the same average Vf% is made. The experimental results show that the failure of the FGM beams under three points bending loading (3PB) test is initiated from the tensioned layers, and spread to the upper layer. The spreading is followed by delamination accompanied by shear failures. Finally, the FGM beams fail due to crushing in the compression zone. Furthermore, the delamination failure between the layers has a major effect on the rapidity of the final failure of the FGM beams. The present numerical results show that the gradient pattern of FGM beams is a critical parameter for improving their flexural behavior. Otherwise, Vf% of the outer layers of the FGM beams, i.e. Vf% = 30, 40, or 50%, is responsible for improving their flexural strength.

Influence of Honeycomb Core Compression on the Mechanical Properties of the Sandwich Structure

2013 ◽  
Vol 486 ◽  
pp. 283-288
Author(s):  
Ladislav Fojtl ◽  
Soňa Rusnáková ◽  
Milan Žaludek
Keyword(s):  
Mechanical Properties ◽  
Impact Test ◽  
Charpy Impact ◽  
Charpy Impact Test ◽  
Low Velocity Impact ◽  
Bending Test ◽  
Honeycomb Core ◽  
Low Velocity ◽  
Three Point Bending ◽  
Core Technology

This research paper deals with an investigation of the influence of honeycomb core compression on the mechanical properties of sandwich structures. These structures consist of prepreg facing layers and two different material types of honeycomb and are produced by modified compression molding called Crush-Core technology. Produced structures are mechanically tested in three-point bending test and subjected to low-velocity impact and Charpy impact test.

Comparison of the Cross Sectional Area, the Loss in Volume and the Mechanical Properties of LAE442 and MgCa0.8 as Resorbable Magnesium Alloy Implants after 12 Months Implantation Duration

2010 ◽  
Vol 638-642 ◽  
pp. 675-680 ◽  
Author(s):  
Martina Thomann ◽  
Nina von der Höh ◽  
Dirk Bormann ◽  
Dina Rittershaus ◽  
C. Krause ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Cross Sections ◽  
Degradation Process ◽  
Cross Sectional Area ◽  
Bending Test ◽  
Sectional Area ◽  
Cross Sectional ◽  
Initial Strength ◽  
Three Point Bending ◽  
The Cross

Current research focuses on magnesium based alloys in the course of searching a resorbable osteosynthetic material which provides sufficient mechanical properties besides a good biocompatibility. Previous studies reported on a favorable biocompatibility of the alloys LAE442 and MgCa0.8. The present study compared the degradation process of cylindrical LAE442 and MgCa0.8 implants after 12 months implantation duration. Therefore, 10 extruded implants (2.5 x 25 mm, cross sectional area 4.9 mm²) of both alloys were implanted into the medullary cavity of both tibiae of rabbits for 12 months. After euthanization, the right bone-implant-compound was scanned in a µ-computed tomograph (µCT80, ScancoMedical) and nine uniformly distributed cross-sections of each implant were used to determine the residual implants´ cross sectional area (Software AxioVisionRelease 4.5, Zeiss). Left implants were taken out of the bone carefully. After weighing, a three-point bending test was carried out. LAE442 implants degraded obviously slower and more homogeneously than MgCa0.8. The mean residual cross sectional area of LAE442 implants was 4.7 ± 0.07 mm². MgCa0.8 showed an area of only 2.18 ± 1.03 mm². In contrast, the loss in volume of LAE442 pins was more obvious. They lost 64 % of their initial weight. The volume of MgCa0.8 reduced clearly to 54.4 % which corresponds to the cross sectional area results. Three point bending tests revealed that LAE442 showed a loss in strength of 71.2 % while MgCa0.8 lost 85.6 % of its initial strength. All results indicated that LAE442 implants degraded slowly, probably due to the formation of a very obvious degradation layer. Degradation of MgCa0.8 implants was far advanced.

Non-Invasive Analysis of the Micro-Structural and Biomechanical Properties of Trabecular Bone in Human Femoral Head

2006 ◽  
Vol 321-323 ◽  
pp. 1070-1073
Author(s):  
Ye Yeon Won ◽  
Myong Hyun Baek ◽  
Wen Quan Cui ◽  
Kwang Kyun Kim
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Femoral Head ◽  
Trabecular Bone ◽  
Volume Fraction ◽  
Reaction Force ◽  
Bone Volume ◽  
Fe Model ◽  
Micro Ct ◽  
Trabecular Thickness

This study investigates micro-structural and mechanical properties of trabecular bone in human femoral head with and without osteoporosis using a micro-CT and a finite element model. 15 cored trabecular bone specimens with 20 of diameter were obtained from femoral heads with osteoporosis resected for total hip arthroplasty, and 5 specimens were removed from femoral head of cadavers, which has no history of musculoskeletal diseases. A high-resolution micro-CT system was used to scan each specimen to obtain histomorphometry indexes. Based on the micro-images, a FE-model was created to determine mechanical property indexes. While the non-osteoporosis group had increases the trabecular thickness, the bone volume, the bone volume fraction, the degree of anisotropy and the trabecular number compared with those of osteoporotic group, the non-osteoporotic group showed decreases in trabecular separation and structure model index. Regarding the mechanical property indexes, the reaction force and the Young's modulus were lower in the osteoporotic group than in non-osteoporotic group. Our data shows salient deteriorations in trabecular micro-structural and mechanical properties in human femoral head with osteoporosis.

Manufacturing and Measuring Mechanical Properties of Continuous Functionally Graded Beam

2021 ◽  
Vol 21 (2) ◽  
pp. 7-11
Author(s):  
Ahmed Mansoor Abbood ◽  
Haider K. Mehbes ◽  
Abdulkareem. F. Hasan
Keyword(s):  
Mechanical Properties ◽  
Young’S Modulus ◽  
Volume Fraction ◽  
Young's Modulus ◽  
Functionally Graded ◽  
High Concentration ◽  
Functionally Graded Beam ◽  
Low Concentration ◽  
Graded Material ◽  
Vertical Gravity

In this study, glass-filled epoxy functionally graded material (FGM) was prepared by adopting the hand lay-up method. The vertical gravity casting was used to produce a continuous variation in elastic properties. A 30 % volume fraction of glass ingredients that have mean diameter 90 μm was spread in epoxy resin (ρ = 1050 kg/m3). The mechanical properties of FGM were evaluated according to ASTM D638. Experimental results showed that a gradually relationship between Young’s modulus and volume fraction of glass particles, where the value of Young’s modulus at high concentration of glass particles was greater than that at low concentration, while the value of Poisson’s ratio at high concentration of glass particles was lower than that at low concentration. The manufacture of this FG beam is particularly important and useful in order to benefit from it in the field of various fracture tests under dynamic or cyclic loads.

Brazed coatings for steam turbine blades: impact of the tape architecture and composition on mechanical properties

2020 ◽  
Vol 111 (11) ◽  
pp. 916-922
Author(s):  
K. Bobzin ◽  
W. Wietheger ◽  
J. Hebing ◽  
L. Gerdt ◽  
H. Krappitz ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Steam Turbine ◽  
Volume Fraction ◽  
Steel Substrate ◽  
Turbine Blades ◽  
Surface Hardness ◽  
Three Point Bending ◽  
Wear And Corrosion ◽  
Steam Turbine Blades ◽  
Positive Effect

Abstract Ni-based brazing coatings with tungsten or chromium carbides are used for wear and corrosion protection in various applications. Steam turbine blades especially present a highly stressed application in which in particular the resistance to erosion and corrosion is essential. Therefore, novel tape architectures of brazed coatings have been developed and investigated within this study. In contrast to the use of powders, the application by means of tapes offers a high potential with regard to later use in industry due to the reproducible handling and automation. In this work, different coating systems were successfully deposited by means of vacuum brazing on X12CrNiMo-12 steel substrate. In order to achieve a sufficient fracture toughness of the coatings, pure nickel powder was added to the tapes. The influence of this additive on the mechanical properties was analyzed by means of three-point bending tests. A positive effect has been observed when adding a volume fraction of φ(Ni) = 25% of nickel, increasing the flexural strength up to σf = 580 MPa. Furthermore, the surface hardness of the coating has been analyzed depending on coating architecture and post-deposition treatment by grinding.

Sign in / Sign up

Export Citation Format

Share Document