scholarly journals Facile Approach to Develop Hierarchical Roughness fiber@SiO2 Blocks for Superhydrophobic Paper

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1393 ◽  
Author(s):  
Qing Wang ◽  
Jieyi Xiong ◽  
Guangxue Chen ◽  
Ouyang Xinping ◽  
Zhaohui Yu ◽  
...  
Keyword(s):  
Large Scale ◽  
Low Cost ◽  
Sol Gel ◽  
Sio2 Nanoparticles ◽  
Contact Angles ◽  
Preparation Process ◽  
Water Contact ◽  
Mechanical Durability ◽  
Complex Preparation ◽  
Superhydrophobic Paper

Papers with nanoscaled surface roughness and hydrophobically modification have been widely used in daily life. However, the relatively complex preparation process, high costs and harmful compounds have largely limited their applications. This research aims to fabricate superhydrophobic papers with low cost and nontoxic materials. The surface of cellulose fibers was initially coated with a film of SiO2 nanoparticles via sol-gel process. After papermaking and subsequent modification with hexadecyltrimethoxysilane through a simple solution-immersion process, the paper showed excellent superhydrophobic properties, with water contact angles (WCA) larger than 150°. Moreover, the prepared paper also showed superior mechanical durability against 10 times of deformation. The whole preparation process was carried out in a mild environment, with no intricate instruments or toxic chemicals, which has the potential of large-scale industrial production and application.

scholarly journals A Simple and Efficient Method to Fabricate Superhydrophobic Wood with Enhanced Mechanical Durability

Forests ◽  
2019 ◽  
Vol 10 (9) ◽  
pp. 750 ◽  
Author(s):  
Han ◽  
Wang ◽  
Zhang ◽  
Pu
Keyword(s):  
Large Scale ◽  
Sio2 Nanoparticles ◽  
Contact Angles ◽  
Superhydrophobic Surfaces ◽  
High Wear Resistance ◽  
Mechanical Resistance ◽  
Water Contact ◽  
Mechanical Durability ◽  
One Step ◽  
Efficient Route

The poor durability and complex production process are two tough challenges for the practical application of superhydrophobic wood. In this work, high-mechanical-resistance superhydrophobic wood was fabricated by a one-step hydrothermal vacuum dipping method using SiO2 nanoparticles (SiO2 NPs) in combination with vinyltriethoxysilane (VTES). The as-prepared superhydrophobic surfaces exhibited water contact angles (CAs) greater than 152° and water sliding angles (SAs) less than 3°. It also exhibited robust stability and durability in harsh conditions, including finger wiping, water brushing, intense sandpaper abrasion, and severe ultrasonic cleaning. The superhydrophobic surface was created by the random distribution of oligomer-wrapped SiO2 NP spheres having different sizes. Further testing showed that the SiO2 NPs were firmly fixed on the wood substrate via chemical bonding, which contributed to the high wear resistance. The modification method developed in this work provides a simple and efficient route to fabricate large-scale, mechanically stable, and durable superhydrophobic surfaces for advanced engineering materials.

scholarly journals Performance Improvement of ZnSnO Thin-Film Transistors with Low-Temperature Self-Combustion Reaction

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1099
Author(s):  
Ye-Ji Han ◽  
Se Hyeong Lee ◽  
So-Young Bak ◽  
Tae-Hee Han ◽  
Sangwoo Kim ◽  
...  
Keyword(s):  
Thin Film ◽  
Photoelectron Spectroscopy ◽  
Large Scale ◽  
Low Cost ◽  
Thermal Analyses ◽  
Thin Film Transistor ◽  
Sol Gel ◽  
Annealing Temperatures ◽  
Zinc Tin Oxide ◽  
Thermal Limitation

Conventional sol-gel solutions have received significant attention in thin-film transistor (TFT) manufacturing because of their advantages such as simple processing, large-scale applicability, and low cost. However, conventional sol-gel processed zinc tin oxide (ZTO) TFTs have a thermal limitation in that they require high annealing temperatures of more than 500 °C, which are incompatible with most flexible plastic substrates. In this study, to overcome the thermal limitation of conventional sol-gel processed ZTO TFTs, we demonstrated a ZTO TFT that was fabricated at low annealing temperatures of 350 °C using self-combustion. The optimized device exhibited satisfactory performance, with μsat of 4.72 cm2/V∙s, Vth of −1.28 V, SS of 0.86 V/decade, and ION/OFF of 1.70 × 106 at a low annealing temperature of 350 °C for one hour. To compare a conventional sol-gel processed ZTO TFT with the optimized device, thermogravimetric and differential thermal analyses (TG-DTA) and X-ray photoelectron spectroscopy (XPS) were implemented.

scholarly journals Upcycling of Vine Shoots: Production of Fillers for PHBV-Based Biocomposite Applications

2020 ◽  
Author(s):  
Grégoire David ◽  
Laurent Heux ◽  
Stéphanie Pradeau ◽  
Nathalie Gontard ◽  
Hélène Angellier-Coussy
Keyword(s):  
Water Vapor ◽  
Gas Phase ◽  
Mechanical Performance ◽  
Low Cost ◽  
Water Vapor Permeability ◽  
Contact Angles ◽  
Vapor Permeability ◽  
Water Contact ◽  
Median Diameter ◽  
Cost Of Materials

Abstract This paper aims at investigating the potential of vine shoots (ViSh) upcycling as fillers in novel poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) based biocomposites. ViSh particles of around 50 µm (apparent median diameter) were obtained combining dry grinding processes, and mixed with PHBV using melt extrusion. Thermal stability and elongation at break of biocomposites were reduced with increasing contents of ViSh particles (10, 20 and 30 wt%), while Young’s modulus and water vapor permeability were increased. It was shown that a surface gas-phase esterification allowed to significantly increase the hydrophobicity of ViSh particles (increase of water contact angles from 59° to 114°), leading to a reduction of 27% in the water vapor permeability of the biocomposite filled with 30 wt% of ViSh. The overall mechanical performance was not impacted by gas-phase esterification, demonstrating that the interfacial adhesion between the virgin ViSh particles and the PHBV matrix was already good and that such filler surface treatment was not required in that case. It was concluded that ViSh particles can be interestingly used as low cost fillers in PHBV-based biocomposites to decrease the overall cost of materials.

Fabrication of super-hydrophobic filter paper via mixed wax phase separation for efficient oil/water separation

BioResources ◽  
2021 ◽  
Vol 16 (3) ◽  
pp. 5794-5805
Author(s):  
Yating Wang ◽  
Xiaochun Chen ◽  
Yaqi Liang ◽  
Chenghua Yu
Keyword(s):  
Filter Paper ◽  
Surface Composition ◽  
Low Cost ◽  
Sliding Angle ◽  
Coated Paper ◽  
Water Contact ◽  
Water Separation ◽  
Oil Separation ◽  
Paper Surface ◽  
Superhydrophobic Paper

Despite previous efforts, the fabrication of superhydrophobic substrate via an environment friendly and easy approach remains a great challenge. In this study, a low cost, simple, and green procedure was developed to prepare a superhydrophobic paper surface that is acceptable for the papermaking industry. First, a wax mixture (beeswax & carnauba wax) was emulsified and coated on the filter paper surface. Then, the coated paper was annealed at different temperatures. The further heat-treatment-rendered wax-coated paper hydrophobic or superhydrophobic because submicrometer or micrometer wax structures were present on the paper surface. The water contact angle of the annealed filter paper sample reached 151.5° at 60 °C, and the sliding angle was under 10°. Further, the relationship between surface composition and the hydrophobic properties of the coated paper samples was discussed. The obtained paper samples showed great potential in water/oil separation, as they had an efficiency over 99%. This work proposed a new simple and mild approach to fabricate superhydrophobic filter papers and explored the hydrophobicity and water/oil separation properties.

scholarly journals Effect of Modified Silica Materials on Polyvinyl Chloride (PVC) Substrates to Obtain Transparent and Hydrophobic Hybrid Coatings

2021 ◽  
Vol 11 (22) ◽  
pp. 11044
Author(s):  
Violeta Purcar ◽  
Valentin Rădițoiu ◽  
Alina Rădițoiu ◽  
Florentina Monica Raduly ◽  
Georgiana Cornelia Ispas ◽  
...  
Keyword(s):  
Polyvinyl Chloride ◽  
Sol Gel ◽  
Contact Angles ◽  
Hybrid Coatings ◽  
Water Contact ◽  
Silica Coatings ◽  
Transmission Electron ◽  
Vis Spectroscopy ◽  
Silica Materials ◽  
Window Blinds

In this research, we report a simple and inexpensive way to prepare transparent and hydrophobic hybrid coatings through deposition of different silica materials on polyvinyl chloride (PVC) substrates. The silica materials were prepared using an acid-catalyzed sol–gel method at room temperature (25 ± 2 °C), using alkoxysilanes: tetraethoxysilane (TEOS), as the silica source, and ethoxydimethylvinylsilane (DMVES), triethoxyoctylsilane (OTES), and trimethoxyhexadecylsilane (HDTMES), as modifier agents. The obtained materials were characterized (either as powders or as thin films) by Fourier-transform infrared spectroscopy (FTIR), UV/Vis spectroscopy, transmission electron microscopy (TEM), thermogravimetric analysis (TGA), atomic force microscopy (AFM), spectroscopic ellipsometry (SE), and water contact-angle measurements. UV/Vis spectra showed that the PVC substrate coated with the silica material containing TEOS/DMVES/OTES had a transmittance of about 90% in the wavelength range of 650–780 nm. The water contact angles increased from 83° for uncoated PVC substrate to ~94° for PVC substrates coated with the sol–gel silica materials. These PVC films with hybrid silica coatings can be used as the materials for outdoor applications, such as energy-generating solar panel window blinds or PVC clear Windmaster outdoor blinds.

An Easy Approach for Obtaining Superhydrophobic Surfaces and their Applications

2019 ◽  
Vol 813 ◽  
pp. 37-42
Author(s):  
Amani Khaskhoussi ◽  
Luigi Calabrese ◽  
Edoardo Proverbio
Keyword(s):  
Surface Morphology ◽  
Large Scale ◽  
Adhesion Force ◽  
Industrial Applications ◽  
Contact Angles ◽  
Boiling Water ◽  
Superhydrophobic Surfaces ◽  
Acid Mixture ◽  
Short Term Treatment ◽  
Water Contact

Three different methods were used to obtain nature-inspired superhydrophobic surfaces on aluminum alloys: short-term treatment with boiling water, HF/HCl and HNO3/HCl concentrated solution etching. Afterwards a thin octadecylsilane film was deposited on all pre-treated surfaces. The surface morphology analysis showed that each method allow to obtain a specific dual nano/micro-structure. The corresponding water contact angles ranged from 160° to nearly 180°. The adhesion force between the water droplets and superhydrophobic surfaces were evaluated. The specimen etched with HF/HCl acid mixture solution showed the lowest adhesion. However, the boiling water treatment sample was characterized by the highest adhesion. Furthermore, the relationship between hydrophobic behavior and surface morphology was discussed compressively. In addition, the electrochemical measurements show that the different superhydrophobic surfaces have an excellent anti-corrosion performance evidencing promising results suitable to obtain large-scale nature-inspired superhydrophobic surfaces for several industrial applications.

scholarly journals Evaluation of CoBlast Coated Titanium Alloy as Proton Exchange Membrane Fuel Cell Bipolar Plates

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Atinuke M. Oladoye ◽  
James G. Carton ◽  
Abdul G. Olabi
Keyword(s):  
Fuel Cell ◽  
Proton Exchange Membrane ◽  
Low Cost ◽  
Electrochemical Behaviour ◽  
Corrosion Current ◽  
Bipolar Plate ◽  
Contact Angles ◽  
Hydrogen Gas ◽  
Proton Exchange ◽  
Water Contact

We investigated the potential of graphite based coatings deposited on titanium V alloy by a low-cost powder based process for bipolar plate application. The coatings which were deposited from a mixture of graphite and alumina powders at ambient temperature, pressure of 90 psi, and speed of 20 mm were characterised and electrochemically polarised in 0.5 M H2SO4 + 2 ppm HF bubbled with air and hydrogen gas to depict the cathode and anode PEM fuel cell environment, respectively. Surface conductivity and water contact angles were also evaluated. Corrosion current in the 1 μA/cm2 range in both cathodic and anodic environment at room temperature and showed negligible influence on the electrochemical behaviour of the bare alloy. Similar performance, which was attributed to the discontinuities in the coatings, was also observed when polarised at 0.6 V and −0.1 V with air and hydrogen bubbling at 70∘C respectively. At 140 N/cm2, the coated alloy exhibited contact resistance of 45.70 mΩ·cm2 which was lower than that of the bare alloy (66.50 mΩ·cm2) but twice that of graphite (21.29 mΩ·cm2). Similarly, the wettability test indicated that the coated layer exhibited higher contact angle of 99.63° than that of the bare alloy (66.32°). Over all, these results indicated need for improvement in the coating process to achieve a continuous layer.

Synthesis and Characterization of ZnO-SiO2/Epoxy Nanocomposite Coating by Sol-Gel Process

2012 ◽  
Vol 16 ◽  
pp. 1-7
Author(s):  
Nazanin Farhadyar ◽  
Mirabdullah Seyed Sadjadi
Keyword(s):  
Polyethylene Glycol ◽  
Sol Gel ◽  
Nanocomposite Coating ◽  
Contact Angles ◽  
Hybrid Coatings ◽  
Coating Film ◽  
Water Contact ◽  
Unit Form ◽  
Hybrid Solution ◽  
Sol Gel Process

In this paper, we report preparation of hydrophilic hybrid nanocomposite coatings on glass substrates using Zinc acetate solutions based on 3-glycidoxypropyltrimethoxysilane (GPTMS), epoxy resin, aromatic amine (HY850), polyethylene glycol (PEG) and surfactant (polyoxyethylene(4)laurylether) by the sol-gel process. Furthermore, the effects of PEG addition to the precursor solutions on the hydrophilic property and microstructure of the resultant coating film were studied. The hydrophilic behavior study of the synthesized hybrid was performed by adding different amounts of polyethylene glycol precursor to the hybrid solution. Experimental results show that, among different amounts of PEGs, the best results are obtained by addition of PEGs (400) to the hybrid solution which can decrease the water contact angles down to 16 and using surfactant down to 0, and increase the free surface energy. Coated glass exhibits a higher strength than uncoated glass. Attenuated total reflectance infrared spectroscopic (ATR-IR) technique was used to characterize the structure of the hybrid films. The chemical structure of obtained network affects morphology of the coating. The morphology of the hybrid coatings was examined by transmission electron microscopy (TEM). The hybrid systems have a unit form structure and the inorganic phases were in the nanosize scale,

Preparation of TiO2 Thin Films and its Superhydrophilic Properties

2009 ◽  
Vol 620-622 ◽  
pp. 695-698
Author(s):  
Jing Ma ◽  
Wen Xiu Liu ◽  
Xiao Guang Qu ◽  
Dan Ni Yu ◽  
Wen Bin Cao
Keyword(s):  
Thin Film ◽  
Tio2 Thin Film ◽  
Annealing Temperature ◽  
Sol Gel ◽  
Soda Lime ◽  
Contact Angles ◽  
Soda Lime Glass ◽  
Water Contact ◽  
Different Temperatures ◽  
Hydrolysis Of

TiO2 thin film was prepared on soda lime glass by hydrolysis of Ti(OC4H9)4 in alcoholic solutions by sol-gel method combined with spin-coating and calcination different temperatures. Prepared samples were characterized by XRD, FESEM, and measurement of contact angles and transmittance. XRD identification reveals that the films are composed of anatase TiO2 when the annealing temperature was set at 450~550 oC. SiO2 layer was coated on the surface of the glass firstly to barrier the diffusing of sodium ions from the substrate. Light-induced superhydrophilicity of the TiO2 thin film has been investigated. To increase the illumination light intensity will decrease the water contact angle. The superhydrophilicity of the TiO2 thin film will disappear more slowly in the dark than that in the field of ultrasound.

scholarly journals A Robust Superhydrophobic Polyurethane Sponge Loaded with Multi-Walled Carbon Nanotubes for Efficient and Selective Oil-Water Separation

Nanomaterials ◽  
2021 ◽  
Vol 11 (12) ◽  
pp. 3344
Author(s):  
De Liu ◽  
Shiying Wang ◽  
Tao Wu ◽  
Yujiang Li
Keyword(s):  
Ionic Strength ◽  
Absorptive Capacity ◽  
Large Scale ◽  
Low Cost ◽  
Absorption Capacity ◽  
Effect Of Temperature ◽  
Water Contact ◽  
Water Separation ◽  
Oil Water Separation ◽  
Oil Water

The influence of different coupling agents and coupling times on the wettability of a polyurethane (PU) sponge surface were optimized. Octadecyltrichlorosilane (OTS) was selected as the optimal coupling agent to prepare the superhydrophobic sponge. The superhydrophobic sponge was prepared in one step, which has the advantages of simple operation and enhanced durability. The superhydrophobic sponge was characterized by scanning electron microscopy, Teclis Tracker tensiometry, and Fourier transform infrared (FT-IR) spectrophotometry. The water contact angle increased from 64.1° to 151.3°, exhibiting ideal superhydrophobicity. Oils and organic solvents with different viscosities and densities can be rapidly and selectively absorbed by superhydrophobic sponges, with an absorption capacity of 14.99 to 86.53 times the weight of the sponge itself, without absorbing any water. Since temperature affects the viscosity and ionic strength of oil, and influences the surface wettability of the sponges, the effect of temperature and ionic strength on the oil absorption capacity of the superhydrophobic sponges was measured, and its mechanism was elucidated. The results showed that the absorptive capacity retained more than 90% of the initial absorptive capacity after repeated use for 10 times. Low-cost, durable superhydrophobic sponges show great potential for large-scale oil-water separation.

Sign in / Sign up

Export Citation Format

Share Document