scholarly journals Effect of Microstructure on Thermophysical Properties of Heat-Treated Duplex Steel

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 6043
Author(s):  
Piotr Koniorczyk ◽  
Judyta Sienkiewicz ◽  
Janusz Zmywaczyk ◽  
Andrzej Dębski ◽  
Mateusz Zieliński ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Thermophysical Properties ◽  
Room Temperature ◽  
Laser Flash ◽  
Micro Hardness ◽  
Scanning Calorimetry ◽  
Air Atmosphere ◽  
Steel Bar ◽  
Heat Treated ◽  
Duplex Steel

The purpose of this study is to investigate the effect of heat treatments and resulting changes in microstructure on the thermophysical properties of commercial 1.4462 duplex stainless steel. Three types of heat treatment and a raw sample were used. In the first heat treatment, a duplex steel bar was annealed in an air atmosphere furnace for one hour at 1200 °C and then quickly cooled in water (1200 °C + water). The second heat treatment was the same as the first, but afterwards, the bar was annealed in an air atmosphere furnace for 4 h at 800 °C and then slowly cooled down in the furnace to room temperature (1200 °C + water + 800 °C). In the third heat treatment, the duplex steel bar was annealed in the furnace in an air atmosphere for one hour at 900 °C and then slowly cooled in the furnace to room temperature (900 °C). As a result, the weight percentages of ferrite and austenite in the samples achieved the following ratios: 75:25, 65:35 and 44:56. Light microscope examinations (LM), scanning electron microscopy (SEM), Vickers micro-hardness measurements and thermophysical studies using a laser flash apparatus (LFA), differential scanning calorimetry (DSC) and push-rod dilatometry (DIL) were performed to reveal the microstructure and changes in thermophysical properties including thermal diffusivity, thermal conductivity, thermal expansion and specific heat. Along with presenting these data, the paper, in brief, presents the applied investigation procedures.

Effect of tensile stress on the annealed structure of a metallic glass

1987 ◽  
Vol 2 (4) ◽  
pp. 461-470 ◽  
Author(s):  
P. T. Vianco ◽  
J. C. M. Li
Keyword(s):  
Heat Treatment ◽  
Differential Scanning Calorimetry ◽  
Glass Transition ◽  
Tensile Stress ◽  
Room Temperature ◽  
Exothermic Peak ◽  
Scanning Calorimetry ◽  
Disordered Structure ◽  
Heat Treated ◽  
Dsc Thermograms

The low-temperature (120°–245°C) structural relaxation of Metglas¯ 2826B (Ni49Fe29P14B6Si2) amorphous alloy was investigated for samples subjected to a tensile stress in the range of 20–400 MPa during annealing. The stress-annealed samples demonstrated a much smaller increase of microhardness than was observed in similarly annealed ribbons without a stress. Further heat treatment of the stress-annealed specimens, this time without the stress, was capable of increasing the microhardnesses of only some ribbons to values equal to those of samples similarly heat treated initially without a stress. An additional exothermic peak in the differential scanning calorimetry (DSC) thermograms of the stress-annealed specimens indicated the presence of a more disordered structure at room temperature, which was found to correlate with the lower microhardness values. Otherwise, those artifacts of the DSC thermograms that were characteristic of samples annealed without a stress were still present in the stress-annealed ribbons. No effect on the crystallization temperature was noted but the glass transition temperature was increased in the stress-annealed case with respect to values attained when the stress was absent during heat treatment. A reduction in the degree of embrittlement of those samples annealed with a tensile stress was a further indication of more disorder in the stress-annealed ribbons.

Mechanical and thermophysical properties of actinide monocarbides

2018 ◽  
Vol 32 (21) ◽  
pp. 1850248 ◽  
Author(s):  
Devraj Singh ◽  
Amit Kumar ◽  
Vyoma Bhalla ◽  
Ram Krishna Thakur
Keyword(s):  
Thermophysical Properties ◽  
Room Temperature ◽  
Nearest Neighbor ◽  
Ultrasonic Attenuation ◽  
Thermal Relaxation ◽  
Nonlinearity Parameter ◽  
Micro Hardness ◽  
Temperature Dependent ◽  
Third Order ◽  
Pressure Derivative

This paper describes the mechanical and thermophysical properties of actinide monocarbides AnCs (An=Np and Cm) as a function of temperature and crystallographic direction. The temperature-dependent second- and third-order elastic constant (SOECs and TOECs) have been computed first using Coulomb and Born–Mayer potential up to second nearest neighbor. SOECs have been applied to find out mechanical constant such as bulk modulus, shear modulus, tetragonal modulus, Poisson’s ratio and Zener anisotropy for the prediction of futuristic performance of the NpC and CmC. We also found the value of G/B [Formula: see text] 0.59 for the chosen materials, which indicates that NpC and CmC have brittle nature. The computed elastic constants are further applied directly to indirectly find out the ultrasonic velocity, Grüneisen parameters, pressure derivative, Debye temperature, micro-hardness, Breazeale’s nonlinearity parameter, thermal relaxation time and thermal conductivity. These evaluated parameters were finally used to compute ultrasonic attenuation of the NpC and CmC along [Formula: see text], [Formula: see text] and [Formula: see text] directions at room temperature. The behavior of the obtained results of this investigation has been compared with similar type of materials.

scholarly journals Wettability Control for Correct Thermophysical Properties Determination of Molten Salts and Their Nanofluids

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3765 ◽  
Author(s):  
Yaroslav Grosu ◽  
Luis González-Fernández ◽  
Udayashankar Nithiyanantham ◽  
Abdessamad Faik
Keyword(s):  
Thermophysical Properties ◽  
Molten Salts ◽  
Laser Flash ◽  
Concentrated Solar Power ◽  
Scanning Calorimetry ◽  
Sample Container ◽  
Low Surface Energy ◽  
Scale Roughness ◽  
Nanoscale Roughness

Proper recording of thermophysical properties for molten salts (MSs) and molten salts based nanofluids (MSBNs) is of paramount importance for the thermal energy storage (TES) technology at concentrated solar power (CSP) plants. However, it is recognized by scientific and industrial communities to be non-trivial, because of molten salts creeping (scaling) inside a measuring crucible or a sample container. Here two strategies are proposed to solve the creeping problem of MSs and MSBNs for the benefit of such techniques as differential scanning calorimetry (DSC) and laser flash apparatus (LFA). The first strategy is the use of crucibles with rough inner surface. It was found that only nanoscale roughness solves the creeping problem, while micron-scale roughness does not affect the wetting phenomena considerably. The second strategy is the use of crucible made of or coated with a low-surface energy material. Both strategies resulted in contact angle of molten salt higher than 90° and as a result, repeatable measurements in correspondence to the literature data. The proposed methods can be used for other characterization techniques where the creeping of molten salts brings the uncertainty or/and unrepeatability of the measurements.

Enhancement of Long-Wavelength Photoluminescence Due to Heat-Treatment in Si-Doped GaAs

1992 ◽  
Vol 262 ◽  
Author(s):  
M. Suezawa ◽  
A. Kasuya ◽  
Y. Nishina ◽  
K. Sumino
Keyword(s):  
Heat Treatment ◽  
Radiative Recombination ◽  
Room Temperature ◽  
Excitation Spectra ◽  
Long Wavelength ◽  
Heat Treated ◽  
Intense Luminescence ◽  
Si Doped

ABSTRACTHighly officient radiative recombination even at room temperature was found at a wavelength of about 1.3 μm in heat-treated Si-doped GaAs. The range of Si concentrations and the condition of heat-treatment to yield this intense luminescence were determined. Excitation spectra of the PL lines suggest that such PL lines are related to pairs of Si-donor and Si- acceptor and such pairs combined with gallium vacancies.

scholarly journals Thermophysical properties of NP2 brand nickel

2021 ◽  
Vol 2119 (1) ◽  
pp. 012135
Author(s):  
D A Samoshkin ◽  
A Sh Agazhanov ◽  
S V Stankus
Keyword(s):  
Thermal Conductivity ◽  
Heat Capacity ◽  
Thermal Diffusivity ◽  
Thermophysical Properties ◽  
Magnetic Phase ◽  
Laser Flash ◽  
Scanning Calorimetry ◽  
Reference Table ◽  
Laser Flash Technique ◽  
Flash Technique

Abstract The heat capacity and the thermal diffusivity of NP2 brand nickel were investigated in the temperature interval 296–1000…1375 K of the solid-state, including the region of the magnetic phase transformation. Measurements were carried out on samples from one initial ingot by laser flash technique and method of differential scanning calorimetry using LFA-427 and DSC 404 F1 setups, respectively. The thermal conductivity was calculated based on the measured thermophysical properties. The estimated errors of the obtained results were 2–4%, 3–5%, and 2–3% for thermal diffusivity, thermal conductivity, and heat capacity, respectively. For investigated thermophysical properties the fitting equations and the reference table have been received.

scholarly journals Влияние термообработки на электрические характеристики полуизолирующих слоев, полученных с помощью облучения n-SiC высокоэнергетическими ионами аргона

2018 ◽  
Vol 44 (6) ◽  
pp. 11 ◽  
Author(s):  
П.А. Иванов ◽  
А.С. Потапов ◽  
М.Ф. Кудояров ◽  
М.А. Козловский ◽  
Т.П. Самсонова
Keyword(s):  
Heat Treatment ◽  
Silicon Carbide ◽  
Room Temperature ◽  
High Energy ◽  
Room Temperature Resistivity ◽  
Electrical Characteristics ◽  
Near Surface ◽  
Heat Treated ◽  
Argon Ions ◽  
Temperature Resistivity

AbstractIrradiation of crystalline n -type silicon carbide ( n -SiC) with high-energy (53-MeV) argon ions was used to create near-surface semi-insulating ( i -SiC) layers. The influence of subsequent heat treatment on the electrical characteristics of i -SiC layers has been studied. The most high-ohmic ion-irradiated i -SiC layers with room-temperature resistivity of no less than 1.6 × 10^13 Ω cm were obtained upon the heat treatment at 600°C, whereas the resistivity of such layers heat-treated at 230°C was about 5 × 10^7 Ω cm.

scholarly journals Hydrogen Detection with SAW Polymer/Quantum Dots Sensitive Films

Sensors ◽  
2019 ◽  
Vol 19 (20) ◽  
pp. 4481 ◽  
Author(s):  
Izabela Constantinoiu ◽  
Cristian Viespe
Keyword(s):  
Heat Treatment ◽  
Quantum Dots ◽  
Room Temperature ◽  
Limit Of Detection ◽  
Composite Films ◽  
High Specific Surface Area ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Heat Treated ◽  
Gas Molecules

Regarding the use of hydrogen as a fuel, it is necessary to measure its concentration in air at room temperature. In this paper, sensitive composite films have been developed for surface acoustic wave (SAW) sensors, using quantum dots (QDs) and polymers. Si/SiO2 QDs were used due to having a high specific surface area, which considerably improves the sensitivity of the sensors compared to those that only have a polymer. Si/SiO2 QDs were obtained by laser ablation and analyzed by X-ray diffraction and transmission electron microscopy (TEM). Two types of polymers were used: polydimethylsiloxane (PDMS) and polymethylmethacrylate (PMMA). Polymer and polymer with QDs compositions were deposited on the sensor substrate by drop casting. A heat treatment was performed on the films at 80 °C with a thermal dwell of two hours. The sensors obtained were tested at different hydrogen concentrations at room temperature. A limit of detection (LOD) of 452 ppm was obtained by the sensor with PDMS and Si/SiO2 QDs, which was heat treated. The results demonstrated the potential of using QDs to improve the sensitivity of the SAW sensors and to achieve a heat treatment that increases its adsorption capacity of the gas molecules.

Platinum-TiO2 (Rutile) Substrate Interaction During Cyclic Oxidation-Reduction Heat-Treatment

1981 ◽  
Vol 39 ◽  
pp. 72-73
Author(s):  
S. Shinozaki ◽  
W. T. Donlon ◽  
A. H. Meitzler
Keyword(s):  
Heat Treatment ◽  
Room Temperature ◽  
Treatment Procedure ◽  
Substrate Interaction ◽  
Reducing Atmosphere ◽  
Oxidation Reduction ◽  
Heat Treated ◽  
Pt Electrodes ◽  
The Matrix ◽  
Tio2 Rutile

When polycrystalline TiO2 (rutile) pellets (∼1mm in thickness and ∼3 mm in diameter), dispersed with Pt particles to act as a catalyst, were heat-treated under certain conditions involving an applied electric field, new unusual microstructures were formed. The heat-treatment procedure was, as follows: 1) apply 1 volt dc field between two Pt electrodes inbedded into the pellet, 2) heat the sample to 750°C and begin cycling the sample between oxydizing (4% O2 in N2) and reducing (2% CO in N2) atmospheres at a rate of several cycles per hour, 3) lower the temperature to 600°C while continually cycling (200 cycle), and, 4) cool the sample to room temperature under the reducing atmosphere (1). The pellet was ion milled to a proper electron transparency and examined by means of a Siemens EM102 and a Philips EM400 TEM-STEM microscope.Some TiO2 grains in this sample exhibited no resolvable defect structure, except that the matrix appeared to be strained due to small defects (Fig. la).

Effect of heat treatment on crystallinity and mechanical properties of flexible structures 3D printed with fused deposition modeling

2021 ◽  
pp. 152808372110649
Author(s):  
Ajay Jayswal ◽  
Sabit Adanur
Keyword(s):  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Fused Deposition Modeling ◽  
Scanning Calorimetry ◽  
Fused Deposition ◽  
Dog Bone ◽  
Heat Treated ◽  
Deposition Modeling ◽  
3D Printed

Fused Deposition Modeling (FDM) is a widely used 3D printing technique, which works based on the principle of melted polymer extrusion through nozzle(s) and depositing them on a build plate layer by layer. However, products manufactured with this method lack proper mechanical strength. In this work, 2/1 twill weave fabric structures are 3D printed using poly (lactic) acid (PLA). The ultimate tensile strength in the warp and weft directions and the modulus (stiffnesses) are measured for non-heat-treated (NHT) samples. The printed samples were heat-treated (HT) to improve the strength and stiffness. The variation in ultimate tensile strength is statistically insignificant in warp direction at all temperatures; however, the tensile strength in weft direction decreased after heat treatment. The modulus in warp direction increased by 31% after heat treatment while in the weft direction it decreased after heat treatment. Differential scanning calorimetry (DSC) tests showed the highest crystallinity at 125°C. The properties of the twill fabrics were compared with a standard dog-bone (DB) specimen using uniaxial tensile tests, Differential scanning calorimetry tests, and optical microscope (OM). For dog-bone specimens, the maximum values of crystallinity, ultimate tensile strength, and modulus were found to be at 125°C. The maximum crystallinity percentages are higher than that of the NHT samples. The ultimate tensile strength of NHT DB specimen 3D printed in horizontal orientation improved after heat treatment. The ultimate tensile strength of DB samples in vertical directions increased after heat treatment as well. The stiffness increased in both directions for DB samples.

THE EFFECT OF LOW TEMPERATURES UPON THE IMPACT RESISTANCE OF STEEL CASTINGS

1930 ◽  
Vol 2 (5) ◽  
pp. 327-340
Author(s):  
R. W. Moffatt
Keyword(s):  
Heat Treatment ◽  
Low Temperatures ◽  
Room Temperature ◽  
Freezing Point ◽  
High Carbon Steel ◽  
Impact Resistance ◽  
Nickel Steel ◽  
Heat Treated ◽  
Steel Castings ◽  
The Impact

The investigation deals with the effect of low temperatures on the impact resistance of steel castings and forgings. Low, medium and high carbon steel castings and a few alloys of vanadium, nickel, and vanadium-nickel steel castings were examined. The metals were subjected to low temperatures, both before and after heat treatment. The temperatures for the tests varied from room temperatures to temperatures well below 0° F., so as to extend below the ordinary atmospheric range of temperatures found in northern climates.It was found that the impact resistances of the metals decreased for temperatures below the freezing point. For specimens, not heat treated, the impact resistance at − 40° F. may be only one-third to one-half of that at room temperature. Heat treatment increases the impact resistance at room temperatures and temperatures below the freezing point. The impact resistance at − 40° F. for the heat-treated metal compared favorably with the impact resistance of the untreated metal at room temperature, 68° F. Heat treatment may slightly lower the yield point and the ultimate tensile strength, but it increases the ductility and the impact resistance of the metal. By proper heat treatment of steel castings the impact resistance at − 40° F. may be brought over 300% higher than that of the untreated metal at that temperature.

Sign in / Sign up

Export Citation Format

Share Document