scholarly journals Power Reduction in Punch-Through Current-Based Electro-Thermal Annealing in Gate-All-Around FETs

Micromachines ◽  
2022 ◽  
Vol 13 (1) ◽  
pp. 124
Author(s):  
Min-Kyeong Kim ◽  
Yang-Kyu Choi ◽  
Jun-Young Park
Keyword(s):  
Thermal Annealing ◽  
Power Efficiency ◽  
Three Dimensional ◽  
Reducing Power ◽  
Power Reduction ◽  
Heat Management ◽  
3D Simulations ◽  
Current Annealing

Device guidelines for reducing power with punch-through current annealing in gate-all-around (GAA) FETs were investigated based on three-dimensional (3D) simulations. We studied and compared how different geometric dimensions and materials of GAA FETs impact heat management when down-scaling. In order to maximize power efficiency during electro-thermal annealing (ETA), applying gate module engineering was more suitable than engineering the isolation or source drain modules.

scholarly journals Giant Magnetoresistance and Magneto-Thermopower in 3D Interconnected NixFe1−x/Cu Multilayered Nanowire Networks

Nanomaterials ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 1133
Author(s):  
Nicolas Marchal ◽  
Tristan da Câmara Santa Clara Gomes ◽  
Flavio Abreu Araujo ◽  
Luc Piraux
Keyword(s):  
Giant Magnetoresistance ◽  
Nanowire Array ◽  
Three Dimensional ◽  
Strong Increase ◽  
Thermoelectric Effect ◽  
Heat Management ◽  
Thermoelectric Effects ◽  
Nanowire Network ◽  
Potential Applications ◽  
Nanowire Networks

The versatility of the template-assisted electrodeposition technique to fabricate complex three-dimensional networks made of interconnected nanowires allows one to easily stack ferromagnetic and non-magnetic metallic layers along the nanowire axis. This leads to the fabrication of unique multilayered nanowire network films showing giant magnetoresistance effect in the current-perpendicular-to-plane configuration that can be reliably measured along the macroscopic in-plane direction of the films. Moreover, the system also enables reliable measurements of the analogous magneto-thermoelectric properties of the multilayered nanowire networks. Here, three-dimensional interconnected NixFe1−x/Cu multilayered nanowire networks (with 0.60≤x≤0.97) are fabricated and characterized, leading to large magnetoresistance and magneto-thermopower ratios up to 17% and −25% in Ni80Fe20/Cu, respectively. A strong contrast is observed between the amplitudes of magnetoresistance and magneto-thermoelectric effects depending on the Ni content of the NiFe alloys. In particular, for the highest Ni concentrations, a strong increase in the magneto-thermoelectric effect is observed, more than a factor of 7 larger than the magnetoresistive effect for Ni97Fe3/Cu multilayers. This sharp increase is mainly due to an increase in the spin-dependent Seebeck coefficient from −7 µV/K for the Ni60Fe40/Cu and Ni70Fe30/Cu nanowire arrays to −21 µV/K for the Ni97Fe3/Cu nanowire array. The enhancement of the magneto-thermoelectric effect for multilayered nanowire networks based on dilute Ni alloys is promising for obtaining a flexible magnetic switch for thermoelectric generation for potential applications in heat management or logic devices using thermal energy.

3D simulations of warm and hot Jupiter atmospheres: the role of 3D mixing in shaping CH4-to-CO conversion pathways

2021 ◽  
Author(s):  
Maria Zamyatina ◽  
Eric Hebrard ◽  
Nathan Mayne ◽  
Benjamin Drummond
Keyword(s):  
Chemical Structure ◽  
Three Dimensional ◽  
Chemical Species ◽  
Radiation Chemistry ◽  
3D Simulations ◽  
Horizontal Advection ◽  
Co Conversion ◽  
Area Of Influence ◽  
Different Parts

<p>We present results from a set of cloud-free simulations of exoplanet atmospheres using a coupled three-dimensional (3D) hydrodynamics-radiation-chemistry model. We report in particular our investigation of the thermodynamic and chemical structure of the atmospheres of HAT-P-11b and WASP-17b and their comparison with the results for the atmospheres of HD 189733b and HD 209458b presented in Drummond et al. (2020). We found that the abundances of chemical species from simulations with interactive chemistry depart from their respective abundances computed at local chemical equilibrium, especially at higher latitudes. To understand this departure, we analysed the CH<sub>4</sub>-to-CO conversion pathways within the Venot et al. (2019) reduced chemical network used in our model using a chemical network analysis. We found that at steady state nine CH<sub>4</sub>-to-CO conversion pathways manifest in our 3D simulations with interactive chemistry, with different pathways dominating different parts of the atmosphere and their area of influence being determined by the vertical and horizontal advection and shifting between planets.</p>

Energy Harvesting for Smart Shoes: A Real Life Application

2013 ◽  
Author(s):  
Emanuele Frontoni ◽  
Adriano Mancini ◽  
Primo Zingaretti ◽  
Andrea Gatto
Keyword(s):  
Energy Harvesting ◽  
Power Efficiency ◽  
Indoor Localization ◽  
Electrical Power ◽  
Real Life ◽  
Reducing Power ◽  
Electrical Energy ◽  
General Purpose ◽  
Technical Developments ◽  
Microprocessor Technology

Advanced technical developments have increased the efficiency of devices in capturing trace amounts of energy from the environment (such as from human movements) and transforming them into electrical energy (e.g., to instantly charge mobile devices). In addition, advancements in microprocessor technology have increased power efficiency, effectively reducing power consumption requirements. In combination, these developments have sparked interest in the engineering community to develop more and more applications that utilize energy harvesting for power. The approach here described aims to designing and manufacturing an innovative easy-to-use and general-purpose device for energy harvesting in general purpose shoes. The novelty of this device is the integration of polymer and ceramic piezomaterials accomplished by injection molding. In this spirit, this paper examines different devices that can be built into a shoe, (where excess energy is readily harvested) and used for generating electrical power while walking. A Main purpose is the development of an indoor localization system embedded in shoes that periodically broadcasts a digital RFID as the bearer walks. Results are encouraging and real life test are conducted on the first series of prototypes.

scholarly journals Design aspects of Bi2Sr2CaCu2O8+δ THz sources: optimization of thermal and radiative properties

2021 ◽  
Author(s):  
Mikhail M Krasnov ◽  
Natalia D Novikova ◽  
Roger Cattaneo ◽  
Alexey A Kalenyuk ◽  
Vladimir M Krasnov
Keyword(s):  
Experimental Data ◽  
Power Efficiency ◽  
Open Space ◽  
Radiation Power ◽  
Impedance Matching ◽  
Dipole Antenna ◽  
Radiative Properties ◽  
Heat Management ◽  
Order Of Magnitude ◽  
Thz Sources

Impedance matching and heat management are important factors influencing performance of THz sources. In this work we analyze thermal and radiative properties of such devices based on mesa structures of a layered high-temperature superconductor Bi2Sr2CaCu2O8+δ. Two types of devices are considered, containing either a conventional large single crystal, or a whisker. We perform numerical simulations for various geometrical configurations and parameters and make a comparison with experimental data for the two types of devices. It is demonstrated that the structure and the geometry of both the superconductor and the electrodes are playing important roles. In crystal-based devices an overlap between the crystal and the electrode leads to appearance of a large parasitic capacitance, which shunts THz emission and prevents impedance matching with open space. The overlap is avoided in whisker-based devices. Furthermore, the whisker and the electrodes form a turnstile (crossed-dipole) antenna facilitating good impedance matching. This leads to more than an order of magnitude enhancement of the radiation power efficiency in whisker-based, compared to crystal-based devices. These results are in good agreement with presented experimental data.

scholarly journals Magnetic Positioning Technique Integrated with Near-Field Communication for Wireless EV Charging

Energies ◽  
2020 ◽  
Vol 13 (5) ◽  
pp. 1081 ◽  
Author(s):  
Zhongnan Qian ◽  
Rui Yan ◽  
Zeqian Cheng ◽  
Jiande Wu ◽  
Xiangning He
Keyword(s):  
Relative Position ◽  
Data Transmission ◽  
Power Efficiency ◽  
Near Field ◽  
Three Dimensional ◽  
Secondary Coil ◽  
Power Transfer ◽  
Electric Vehicle Charging ◽  
Position Detection ◽  
Positioning Method

For wireless electric vehicle charging, the relative position of the primary and secondary coils has significant impacts on the transferred power, efficiency and leakage magnetic flux. In this paper, a magnetic positioning method using simultaneous power and data transmission (SWPDT) is proposed for power coil alignment. Four signal coils are installed on the primary coil to detect the secondary coil position. By measuring the positioning signal amplitudes from the four signal coils, the power coil relative position can be obtained. Moreover, all the communication needed in the positioning process can be satisfied well by SWPDT technology, and no extra radio frequency (RF) communication hardware is needed. The proposed positioning method can work properly both in power transfer online condition and in power transfer offline condition. Thus, a highly integrated wireless charging system is achieved, which features simultaneous power transfer, data transmission and position detection. A positioning experimental setup is built to verify the proposed method. The experimental results demonstrate that the positioning resolution can be maintained no lower than 1 cm in a 1060 mm × 900 mm elliptical region for a pair of 510 mm × 410 mm rectangular power coils. The three-dimensional positioning accuracy achieves up to 1 cm.

scholarly journals Biofuel-powered soft electronic skin with multiplexed and wireless sensing for human-machine interfaces

2020 ◽  
Vol 5 (41) ◽  
pp. eaaz7946 ◽  
Author(s):  
You Yu ◽  
Joanna Nassar ◽  
Changhao Xu ◽  
Jihong Min ◽  
Yiran Yang ◽  
...  
Keyword(s):  
Human Body ◽  
Power Efficiency ◽  
Near Field ◽  
Three Dimensional ◽  
Biofuel Cells ◽  
Physical Parameters ◽  
Power Intensity ◽  
Electronic Skin ◽  
Self Powered ◽  
Body Self

Existing electronic skin (e-skin) sensing platforms are equipped to monitor physical parameters using power from batteries or near-field communication. For e-skins to be applied in the next generation of robotics and medical devices, they must operate wirelessly and be self-powered. However, despite recent efforts to harvest energy from the human body, self-powered e-skin with the ability to perform biosensing with Bluetooth communication are limited because of the lack of a continuous energy source and limited power efficiency. Here, we report a flexible and fully perspiration-powered integrated electronic skin (PPES) for multiplexed metabolic sensing in situ. The battery-free e-skin contains multimodal sensors and highly efficient lactate biofuel cells that use a unique integration of zero- to three-dimensional nanomaterials to achieve high power intensity and long-term stability. The PPES delivered a record-breaking power density of 3.5 milliwatt·centimeter−2 for biofuel cells in untreated human body fluids (human sweat) and displayed a very stable performance during a 60-hour continuous operation. It selectively monitored key metabolic analytes (e.g., urea, NH4+, glucose, and pH) and the skin temperature during prolonged physical activities and wirelessly transmitted the data to the user interface using Bluetooth. The PPES was also able to monitor muscle contraction and work as a human-machine interface for human-prosthesis walking.

Regimes of Dry Convection above Wildfires: Sensitivity to Fire Line Details

2010 ◽  
Vol 67 (3) ◽  
pp. 611-632 ◽  
Author(s):  
Michael T. Kiefer ◽  
Matthew D. Parker ◽  
Joseph J. Charney
Keyword(s):  
Line Shape ◽  
3D Model ◽  
Three Dimensional ◽  
Vertical Wind Shear ◽  
Heating Rates ◽  
3D Simulations ◽  
Complex Phenomena ◽  
2D And 3D ◽  
The Impact ◽  
Dry Convection

Abstract Fire lines are complex phenomena with a broad range of scales of cross-line dimension, undulations, and along-line variation in heating rates. While some earlier studies have examined parcel processes in two-dimensional simulations, the complexity of fire lines in nature motivates a study in which the impact of three-dimensional fire line details on parcel processes is examined systematically. This numerical modeling study aims to understand how fundamental processes identified in 2D simulations operate in 3D simulations where the fire line is neither straight nor uniform in intensity. The first step is to perform simulations in a 3D model, with no fire line undulations or inhomogeneity. In general, convective modes simulated in the 2D model are reproduced in the 3D model. In one particular case with strong vertical wind shear, new convection develops separate from the main line of convection as a result of local changes to parcel speed and heating. However, in general the processes in the 2D and 3D simulations are identical. The second step is to examine 3D experiments wherein fire line shape and along-line inhomogeneity are varied. Parcel heating, as well as convective mode, is shown to exhibit sensitivity to fire line shape and along-line inhomogeneity.

scholarly journals Three-dimensional electromagnetic simulation of monolithic radial transmission lines for Z-pinch

2014 ◽  
Vol 32 (4) ◽  
pp. 599-603 ◽  
Author(s):  
Chongyang Mao ◽  
Xiaobing Zou ◽  
Xinxin Wang
Keyword(s):  
Transmission Lines ◽  
Power Efficiency ◽  
Circuit Simulation ◽  
Three Dimensional ◽  
Electromagnetic Simulation ◽  
Transmitted Power ◽  
Hyperbolic Line ◽  
Tem Mode ◽  
The Difference ◽  
Z Pinch

AbstractThe electromagnetic simulation of the monolithic radial transmission lines for future Z-pinch was performed. Focusing on the difference in the maximum transmitted power efficiency between the electromagnetic simulation and the circuit simulation, the monolithic radial transmission lines with different impedance profile (exponential, Gaussian, hyperbolic) were compared. The power efficiency for the exponential line is higher than that for the Gaussian lines and the hyperbolic line, which is similar to that from the circuit simulation. However, all the power efficiencies obtained with the electromagnetic simulation are about 15% lower than those obtained with the circuit simulation, indicating the existence of considerable non-TEM modes and a non-ignorable error in the circuit simulation based on the quasi-TEM mode approximation. In consideration of several monolithic radial transmission lines being stacked together and the flat electrodes required by the stacked lines, the hyperbolic line was compared with the exponential line with several wide radial slots cut on the flat electrodes. While the hyperbolic line has a little bit lower transmitted power efficiency than that of the exponential line, it is much easier in fabrication. For this reason, the hyperbolic line was recommended as the best choice.

scholarly journals The Dynamic Three-Dimensional Localization of Fields in Active Percolating Systems

2019 ◽  
Vol 2019 ◽  
pp. 1-7
Author(s):  
Gennadiy Burlak
Keyword(s):  
Fractal Dimension ◽  
Nonlinear System ◽  
Three Dimensional ◽  
Percolation Cluster ◽  
Localized States ◽  
3D Simulations ◽  
Localized Solutions ◽  
Anisotropic Inhomogeneity

We study a dynamic three-dimensional (3D) field localized states in a medium with percolation disorder, where the percolation cluster is filled by the active nanoemitters. In such a system, the incipient percolating cluster generates a fractal radiating structure in which the field is radiated and scattered by the anisotropic inhomogeneity. Our numerical 3D simulations show that such a nonlinear system with noninteger fractal dimension has well-defined localized solutions for fields (3D speckles). The statistics of speckles is studied too.

scholarly journals Energy-Efficiency Analysis of Per-Subcarrier Antenna Selection with Peak-Power Reduction in MIMO-OFDM Wireless Systems

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Ngoc Phuc Le ◽  
Le Chung Tran ◽  
Farzad Safaei
Keyword(s):  
Energy Efficiency ◽  
Power Efficiency ◽  
Peak Power ◽  
Antenna Selection ◽  
Average Power ◽  
Wireless Systems ◽  
Power Reduction ◽  
Cumulative Distribution ◽  
Peak Power Reduction ◽  
Mimo Ofdm

The use of per-subcarrier antenna subset selection in OFDM wireless systems offers higher system capacity and/or improved link reliability. However, the implementation of the conventional per-subcarrier selection scheme may result in significant fluctuations of the average power and peak power across antennas, which affects the potential benefits of the system. In this paper, power efficiency of high-power amplifiers and energy efficiency in per-subcarrier antenna selection MIMO-OFDM systems are investigated. To deliver the maximum overall power efficiency, we propose a two-step strategy for data-subcarrier allocation. This strategy consists of an equal allocation of data subcarriers based on linear optimization and peak-power reduction via cross-antenna permutations. For analysis, we derive the CCDF (complementary cumulative distribution function) of the power efficiency as well as the analytical expressions of the average power efficiency. It is proved from the power-efficiency perspective that the proposed allocation scheme outperforms the conventional scheme. We also show that the improvement in the power efficiency translates into an improved capacity and, in turn, increases energy efficiency of the proposed system. Simulation results are provided to validate our analyses.

Sign in / Sign up

Export Citation Format

Share Document