scholarly journals Effect of RF Power on the Physical Properties of Sputtered ZnSe Nanostructured Thin Films for Photovoltaic Applications

Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 2841
Author(s):  
Ovidiu TOMA ◽  
Vlad-Andrei ANTOHE ◽  
Ana-Maria PANAITESCU ◽  
Sorina IFTIMIE ◽  
Ana-Maria RĂDUŢĂ ◽  
...  
Keyword(s):  
Thin Films ◽  
Band Gap ◽  
Optical Glass ◽  
Electrical Characterization ◽  
Rf Magnetron Sputtering ◽  
Rf Plasma ◽  
Glass Substrates ◽  
Exponential Trap Distribution ◽  
The One ◽  
Znse Thin Films

Zinc selenide (ZnSe) thin films were deposited by RF magnetron sputtering in specific conditions, onto optical glass substrates, at different RF plasma power. The prepared ZnSe layers were afterwards subjected to a series of structural, morphological, optical and electrical characterizations. The obtained results pointed out the optimal sputtering conditions to obtain ZnSe films of excellent quality, especially in terms of better optical properties, lower superficial roughness, reduced micro-strain and a band gap value closer to the one reported for the ZnSe bulk semiconducting material. Electrical characterization were afterwards carried out by measuring the current–voltage (I-V) characteristics at room temperature, of prepared “sandwich”-like Au/ZnSe/Au structures. The analysis of I-V characteristics have shown that at low injection levels there is an Ohmic conduction, followed at high injection levels, after a well-defined transition voltage, by a Space Charge Limited Current (SCLC) in the presence of an exponential trap distribution in the band gap of the ZnSe thin films. The results obtained from all the characterization techniques presented, demonstrated thus the potential of ZnSe thin films sputtered under optimized RF plasma conditions, to be used as alternative environmentally-friendly Cd-free window layers within photovoltaic cells manufacturing.

Single Crystal, High Band Gap CdS Thin Films Grown by RF Magnetron Sputtering in Argon Atmosphere for Solar Cell Applications

2018 ◽  
Vol 10 (3) ◽  
pp. 03005-1-03005-6 ◽  
Author(s):  
Rupali Kulkarni ◽  
◽  
Amit Pawbake ◽  
Ravindra Waykar ◽  
Ashok Jadhawar ◽  
...  
Keyword(s):  
Thin Films ◽  
Solar Cell ◽  
Magnetron Sputtering ◽  
Single Crystal ◽  
Band Gap ◽  
Rf Magnetron Sputtering ◽  
Argon Atmosphere ◽  
Cds Thin Films ◽  
High Band

Deposition time dependent study of structural and optical properties of PbS thin films grown by CBD method

2020 ◽  
Vol 13 ◽  
Author(s):  
Minakshi Chaudhary ◽  
Yogesh Hase ◽  
Ashwini Punde ◽  
Pratibha Shinde ◽  
Ashish Waghmare ◽  
...  
Keyword(s):  
Thin Films ◽  
Optical Properties ◽  
Band Gap ◽  
Deposition Time ◽  
Secondary Growth ◽  
Cost Effective ◽  
Xrd Analysis ◽  
Structural Morphology ◽  
Glass Substrates ◽  
Cbd Method

: Thin films of PbS were prepared onto glass substrates by using a simple and cost effective CBD method. Influence of deposition time on structural, morphology and optical properties have been investigated systematically. The XRD analysis revealed that PbS films are polycrystalline with preferred orientation in (200) direction. Enhancement in crystallinity and PbS crystallite size has been observed with increase in deposition time. Formation of single phase PbS thin films has been further confirmed by Raman spectroscopy. The surface morphology analysis revealed the formation of prismatic and pebble-like PbS particles and with increase in deposition time these PbS particles are separated from each other without secondary growth. The data obtained from the EDX spectra shows the formation of high-quality but slightly sulfur rich PbS thin films over the entire range of deposition time studied. All films show increase in absorption with increase in deposition time and a strong absorption in the visible and sub-band gap regime of NIR range of the spectrum with red shift in band edge. The optical band gap shows decreasing trend, as deposition time increases but it is higher than the band gap of bulk PbS.

Optical Properties and Zinc Nitride Thin Films Prepared Using Magnetron Reactive Sputtering

2014 ◽  
Vol 940 ◽  
pp. 11-15
Author(s):  
Jun Qin Feng ◽  
Jun Fang Chen
Keyword(s):  
Thin Films ◽  
Band Gap ◽  
Near Infrared ◽  
Fluorescence Emission ◽  
Emission Spectra ◽  
Sem Images ◽  
Fluorescence Emission Spectra ◽  
Glass Substrates ◽  
Zinc Nitride ◽  
Direct Band

Zinc nitride films were deposited by ion sources-assisted magnetron sputtering with the use of Zn target (99.99% purity) on 7059 glass substrates. The films were characterized by XRD, SEM and EDS, the results of which show that the polycrystalline zinc nitride thin film can be grown on the glass substrates, the EDS spectrum confirmed the chemical composition of the films and the SEM images revealed that the zinc nitride thin films have a dense structure. Ultraviolet-visible-near infrared spectrophotometer was used to study the transmittance behaviors of zinc nitride thin films, which calculated the optical band gap by Davis Mott model. The results of the fluorescence emission spectra show the zinc nitride would be a direct band gap semiconductor material.

Fabrication and Photoelectrochemical Characterization of Fe, Co, Ni and Cu-Doped TiO2 Thin Films

2013 ◽  
Vol 764 ◽  
pp. 266-283 ◽  
Author(s):  
Ibram Ganesh ◽  
Rekha Dom ◽  
P.H. Borse ◽  
Ibram Annapoorna ◽  
G. Padmanabham ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Metal Ions ◽  
Band Gap ◽  
Metal Ion ◽  
Band Gap Energy ◽  
Chemical Compositions ◽  
Gap Energy ◽  
Glass Substrates ◽  
Photoelectrochemical Characterization

Different amounts of Fe, Co, Ni and Cu-doped TiO2 thin films were prepared on fluorine doped tin oxide (FTO) coated soda-lime glass substrates by following a conventional sol-gel dip-coating technique followed by heat treatment at 550 and 600°C for 30 min. These thin films were characterized for photo-current, chronoamperometry and band-gap energy values. The chemical compositions of metals-doped TiO2 thin films on FTO glass substrates were confirmed by XPS spectroscopic study. The metal-ions doped TiO2 thin films had a thickness of <200 nm="" optical="" transparency="" of="">80%, band-gap energy of >3.6 eV, and a direct band-to-band energy transition. The photoelectrochemical (PEC) studies revealed that all the metal-ions doped TiO2 thin films exhibit n-type semi-conducting behavior with a quite stable chronoamperometry and photo-currents that increase with the increase of applied voltage but decrease with the dopant metal-ion concentration in the thin film. Furthermore, these thin films exhibited flat-band potentials amenable to water oxidation reaction in a PEC cell. The 0.5 wt.% Cu-doped TiO2 thin film electrode exhibited an highest incident photon-to-current conversion efficiency (IPCE) of about 21%.

Dependence of Film Thickness on Properties of Al Doped ZnO Thin Films

2011 ◽  
Vol 194-196 ◽  
pp. 2305-2311
Author(s):  
Ying Ge Yang ◽  
Dong Mei Zeng ◽  
Hai Zhou ◽  
Wen Ran Feng ◽  
Shan Lu ◽  
...  
Keyword(s):  
Thin Films ◽  
Film Thickness ◽  
Electrical Parameter ◽  
Substrate Surface ◽  
Rf Magnetron Sputtering ◽  
Thickness Effect ◽  
Visible Range ◽  
Glass Substrates ◽  
Doped Zno

In this study high quality of Al doped ZnO (ZAO) thin films were prepared by RF magnetron sputtering on glass substrates at room temperature in order to study the thickness effect upon their structure, electrical and optical properties. XRD results show that the films are polycrystalline and with strongly preferred (002) orientation perpendicular to substrate surface whatever the thickness is. The crystallite size was calculated by Williamson-Hall method, while it increases as the film thickness increased. The lattice stress is mainly caused by the growth process. Hall measurements revealed electrical parameter very dependent upon thickness when the thickness of ZAO film is lower than 700 nm. The resistivity decreased and the carrier concentration and Hall mobility increases as the film thickness increased. When film thickness becomes larger, only a little change in the above properties was observed. All the films have high transmittance above 90% in visible range. Red shift of the absorption edge was observed as thickness increased. The optical energy bandgap decreased from 3.41eV to 3.30 eV with the increase of film thickness.

Preparation and characterization of V2O5 doped SiO2-TiO2 thin films

2012 ◽  
Vol 2 (1) ◽  
Author(s):  
Marek Nocuń ◽  
Sławomir Kwaśny
Keyword(s):  
Thin Films ◽  
Band Gap ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Dip Coating ◽  
Band Gap Energy ◽  
Tio2 Thin Films ◽  
Glass Substrates ◽  
Gel Technique

AbstractIn our investigation, V doped SiO2/TiO2 thin films were prepared on glass substrates by dip coating sol-gel technique. Chemical composition of the samples was studied by X-ray photoelectron spectroscopy (XPS). Transmittance of the samples was characterized using UV-VIS spectrophotometry. Subsequently band-gap energy (Eg) was estimated for these films. Powders obtained from sols were characterized by FTIR spectroscopy. It was found that vanadium decreases optical band gap of SSiO2/TiO2 films.

scholarly journals Residual Oxygen Effects on the Properties of MoS2 Thin Films Deposited at Different Temperatures by Magnetron Sputtering

Crystals ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1183
Author(s):  
Peiyu Wang ◽  
Xin Wang ◽  
Fengyin Tan ◽  
Ronghua Zhang
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Magnetron Sputtering ◽  
Deposition Rate ◽  
Deposition Temperature ◽  
Energy Dispersive Spectrometer ◽  
Rf Magnetron Sputtering ◽  
Glass Substrates ◽  
Different Temperatures ◽  
Oxygen Atoms

Molybdenum disulfide (MoS2) thin films were deposited at different temperatures (150 °C, 225 °C, 300 °C, 375 °C, and 450 °C) on quartz glass substrates and silicon substrates using the RF magnetron sputtering method. The influence of deposition temperature on the structural, optical, electrical properties and deposition rate of the obtained thin films was investigated by X-ray diffraction (XRD), Energy Dispersive Spectrometer (EDS), Raman, absorption and transmission spectroscopies, a resistivity-measuring instrument with the four-probe method, and a step profiler. It was found that the MoS2 thin films deposited at the temperatures of 150 °C, 225 °C, and 300 °C were of polycrystalline with a (101) preferred orientation. With increasing deposition temperatures from 150 °C to 300 °C, the crystallization quality of the MoS2 thin films was improved, the Raman vibrational modes were strengthened, the deposition rate decreased, and the optical transmission and bandgap increased. When the deposition temperature increased to above 375 °C, the molecular atoms were partially combined with oxygen atoms to form MoO3 thin film, which caused significant changes in the structural, optical, and electrical properties of the obtained thin films. Therefore, it was necessary to control the deposition temperature and reduce the contamination of oxygen atoms throughout the magnetron sputtering process.

Absorber Films of Ag2S and AgBiS2 prepared by Chemical Bath Deposition

2002 ◽  
Vol 730 ◽  
Author(s):  
A. Nuñez Rodriguez ◽  
M.T.S. Nair ◽  
P.K. Nair
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Electrical Conductivity ◽  
Silver Nitrate ◽  
Band Gap ◽  
Chemical Bath Deposition ◽  
Optical Band Gap ◽  
Sodium Thiosulfate ◽  
Xrd Pattern ◽  
Glass Substrates

AbstractAg2S thin films of 90 nm to 300 nm in thickness were deposited at 70°C on glass substrates immersed in a bath mixture containing silver nitrate, sodium thiosulfate and dimethylthiourea. When the films are heated in nitrogen at temperatures 200°C to 400°C, crystallinity is improved and XRD pattern similar to that of acanthite is observed. These films possess electrical conductivity of 10-3 (ohm cm)-1, are photoconductive and exhibit an optical band gap of 1.36 eV. When Ag2S thin film is deposited over a thin film of Bi2S3, also obtained by chemical bath deposition from bismuth nitrate, triethanolamine and thioacetamide, and heated at 300°C to 400°C in nitrogen, a ternary compound, AgBiS2 is formed. This material has an electrical conductivity of 5x10-5 (ohm cm)-1, is photoconductive and possesses optical band gap 0.95 eV.

scholarly journals The Properties of Zn-Doped AlSb Thin Films Prepared by Pulsed Laser Deposition

Coatings ◽  
2019 ◽  
Vol 9 (2) ◽  
pp. 136
Author(s):  
Ping Tang ◽  
Weimin Wang ◽  
Bing Li ◽  
Lianghuan Feng ◽  
Guanggen Zeng
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Band Gap ◽  
Photovoltaic Effect ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Sem Images ◽  
Glass Substrates ◽  
Substrate Temperatures

Aluminum antimony (AlSb) is a promising photovoltaic material with a band gap of about 1.62 eV. However, AlSb is highly deliquescent and not stable, which has brought great difficulties to the applications. Based on the above situation, there are two purposes for preparing our Zn-doped AlSb (AlSb:Zn) thin films: One is to make P-type AlSb and the other is to find a way to suppress the deliquescence of AlSb. The AlSb:Zn thin films were prepared on glass substrates at different substrate temperatures by using the pulsed laser deposition (PLD) method. The structural, surface morphological, optical, and electrical properties of AlSb:Zn films were investigated. The crystallization of AlSb:Zn thin films was enhanced and the electrical resistivity decreased as the substrate temperature increased. The scanning electron microscopy (SEM) images indicated that the grain sizes became bigger as the substrate temperatures increased. The Raman vibration mode AlSb:Zn films were located at ~107 and ~142 cm−1 and the intensity of Raman peaks was stronger at higher substrate temperatures. In the experiment, a reduced band gap (1.4 eV) of the AlSb:Zn thin film was observed compared to the undoped AlSb films, which were more suitable for thin-film solar cells. Zn doping could reduce the deliquescent speed of AlSb thin films. The fabricated heterojunction device showed the good rectification behavior, which indicated the PN junction formation. The obvious photovoltaic effect has been observed in an FTO/ZnS/AlSb:Zn/Au device.

Electrical Characterization and Microstructures of Y2O3-Doped Bi4Ti3O12 Thin Films

2013 ◽  
Vol 591 ◽  
pp. 208-211
Author(s):  
Min Chen ◽  
J. Liu ◽  
X.A. Mei
Keyword(s):  
Thin Films ◽  
Electrical Characterization ◽  
Rf Magnetron Sputtering ◽  
Layered Perovskite ◽  
Random Orientation ◽  
Large Shift ◽  
Si Substrates ◽  
Layered Perovskite Structure ◽  
Lower Temperature ◽  
Curie Temperature Tc

Y2O3-doped bismuth titanate (Bi4-xYxTi3O12: BYT) and pure Bi4Ti3O12 (BIT) thin films with random orientation were fabricated on Pt/Ti/SiO2/Si substrates by rf magnetron sputtering technique. These samples had polycrystalline Bi-layered perovskite structure without preferred orientation, and consisted of well developed rod-like grains with random orientation. Y-doping into BIT caused a large shift of the Curie temperature ( TC ) from 675 °C to lower temperature and a improvement in dielectric property. The experimental results indicated that Y doping into BIT also result in a remarkable improvement in ferroelectric property. The Pr and the Ec values of the BYT film with x=0.75 were 28 μC/cm2 and 65 kV/cm, respectively.

Sign in / Sign up

Export Citation Format

Share Document