scholarly journals Development of Nanoporous AAO Membrane for Nano Filtration Using the Acoustophoresis Method

Sensors ◽  
2020 ◽  
Vol 20 (14) ◽  
pp. 3833
Author(s):  
Yatinkumar Patel ◽  
Giedrius Janusas ◽  
Arvydas Palevicius ◽  
Andrius Vilkauskas
Keyword(s):  
Acoustic Waves ◽  
Chemical Properties ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Nanoporous Structure ◽  
Destructive Testing ◽  
Water Contact ◽  
Force Microscopy ◽  
Interpore Distance ◽  
Nanoporous Surface

A concept of a nanoporous anodic aluminum oxide (AAO) membrane as a vibro-active micro/nano-filter in a micro hydro mechanical system for the filtration, separation, and manipulation of bioparticles is reported in this paper. For the fabrication of a nanoporous AAO, a two-step mild anodization (MA) and hard anodization (HA) technique was used. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) were used to analyze the surface morphology of nanoporous AAO. A nanoporous structure with a pore diameter in the range of 50–90 nm, an interpore distance of 110 nm, and an oxide layer thickness of 0.12 mm with 60.72% porosity was obtained. Fourier-transform infrared spectroscopy (FTIR) and energy-dispersive X-ray spectroscopy (EDS) were employed to evaluate AAO chemical properties. The obtained results showed that the AAO structure is of hexagonal symmetry and showed where Al2O3 is dominant. The hydrophobic properties of the nanoporous surface were characterized by water contact angle measurement. It was observed that the surface of the nanoporous AAO membrane is hydrophilic. Furthermore, to determine whether a nanomembrane could function as a vibro-active nano filter, a numerical simulation was performed using COMSOL Multiphysics 5.4 (COMSOL Inc, Stockholm, Sweden). Here, a membrane was excited at a frequency range of 0–100 kHz for surface acoustics wave (SAW) distribution on the surface of the nanoporous AAO using a PZT 5H cylinder (Piezo Hannas, Wuhan, China). The SAW, standing acoustic waves, and travelling acoustic waves of different wavelengths were excited to the fabricated AAO membrane and the results were compared with experimental ones, obtained from non-destructive testing method 3D scanning vibrometer (PSV-500-3D-HV, Polytec GmbH, Waldbronn, Germany) and holographic interferometry system (PRISM, Hy-Tech Forming Systems (USA), Phoenix, AZ, USA). Finally, a simulation of a single nanotube was performed to analyze the acoustic pressure distribution and time, needed to center nanoparticles in the nanotube.

Surface hydrophilizing modification of polytetrafluoroethylene/glass fiber fabric through oxidant-induced polydopamine deposition

2019 ◽  
Vol 50 (3) ◽  
pp. 364-379
Author(s):  
Yanfen Zhou ◽  
Liang Jiang ◽  
Zhiqing Jiang ◽  
Shaojuan Chen ◽  
Jianwei Ma
Keyword(s):  
Contact Angle ◽  
Glass Fiber ◽  
Water Contact Angle ◽  
Mechanical Stability ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Force Microscopy ◽  
Atomic Force ◽  
Fiber Fabric

This paper reports surface hydrophilizing modification of polytetrafluoroethylene/glass fiber fabric by employing bio-inspired polydopamine functionalization. The modification process was accelerated by introducing sodium periodate (NaIO4) as oxidant. Surface morphology and chemical composition of the modified polytetrafluoroethylene/glass fiber fabric were characterized by using scanning electron microscopy, atomic force microscopy (AFM), and Fourier transform infrared spectroscopy, respectively. Hydrophilicity of the polytetrafluoroethylene/glass fiber fabric was investigated through water contact angle measurement. It was found that polydopamine successfully deposited on the surface of polytetrafluoroethylene/glass fiber fabric and the uniformity of the polydopamine coating increased with increasing modification time. Water contact angle of polytetrafluoroethylene/glass fiber fabric decreased after polydopamine modification and reached 29° when the sample was treated for 120 min, indicating an improved hydrophilic performance. The formed polydopamine coating was also demonstrated to have reliable chemical and mechanical stability.

scholarly journals Silicalite-1 Layers as a Biocompatible Nano- and Micro-Structured Coating: An In Vitro Study on MG-63 Cells

Materials ◽  
2019 ◽  
Vol 12 (21) ◽  
pp. 3583 ◽  
Author(s):  
Martina Doubkova ◽  
Ivana Nemcakova ◽  
Ivan Jirka ◽  
Vitezslav Brezina ◽  
Lucie Bacakova
Keyword(s):  
Photoelectron Spectroscopy ◽  
Chemical Properties ◽  
In Vitro Study ◽  
Ammonium Hydroxide ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Orthopaedic Implants ◽  
Water Contact ◽  
Physico Chemical

Silicalite-1 is a purely siliceous form of zeolite, which does not contain potentially harmful aluminum in its structure as opposed to ZSM-5 aluminosilicate types of zeolite. This paper reports on a study of a silicalite-1 film, deposited on a silicon Si(100) substrate, as a potential anti-corrosive and biocompatible coating for orthopaedic implants. Silicalite-1 film was prepared in situ on the surface of Si(100) wafers using a reaction mixture of tetrapropyl-ammonium hydroxide (TPAOH), tetraethyl-orthosilicate (TEOS), and diH2O. The physico-chemical properties of the obtained surface were characterized by means of X-ray photoelectron spectroscopy, water contact angle measurement, atomic force microscopy, and scanning electron microscopy. The biocompatibility was assessed by interaction with the MG-63 cell line (human osteosarcoma) in terms of cell adhesion, morphology, proliferation, and viability. The synthesized silicalite-1 film consisted of two layers (b- and a, b-oriented crystals) creating a combination of micro- and nano-scale surface morphology suitable for cell growth. Despite its hydrophobicity, the silicalite-1 film increased the number of initially adhered human osteoblast-like MG-63 cells and the proliferation rate of these cells. The silicalite-1 film also improved the cell viability in comparison with the reference Si(100) substrate. It is therefore a promising candidate for coating of orthopaedic implants.

Stimuli-Responsive Films Based on N-Substituted Polyurethane with Different Alkyl Length

2013 ◽  
Vol 66 (11) ◽  
pp. 1361 ◽  
Author(s):  
Yanyan Wang ◽  
Libin Liu ◽  
Congde Qiao ◽  
Tianduo Li
Keyword(s):  
Contact Angle ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Stimuli Responsive ◽  
Scanning Calorimetry ◽  
Remarkable Change ◽  
Water Contact ◽  
Force Microscopy ◽  
Poly Propylene ◽  
Chain Lengths

N-Alkyl-substituted polyurethanes with different alkyl chain lengths were prepared from the corresponding bromoalkane (1-bromooctane, 1-bromotetradecane, and 1-bromooctadecane) and polyurethane consisting of poly(propylene glycol) (PPG), 4,4′-diphenylmethane diisocyanate, and 1,4-butanediol. The synthesised materials were characterised by 1H NMR and FTIR spectroscopy and the degrees of substitution were discussed by changing the reaction conditions. Differential scanning calorimetry and X-ray diffraction were used to characterise the thermal properties and crystalline state. Microphase-separated nanostructures, with hard segments (nanofibre-like) embedded into amorphous PPG soft segments, are observed by atomic force microscopy and scanning electron microscopy. A reversible behaviour of the films was revealed by contact angle measurement. Stimuli-responsive films were realised by solvent vapour annealing and heat treatment, and exhibited a reversible switching in surface wettability with a remarkable change in the water contact angle of 21°.

scholarly journals Superhydrophobic functionalized cellulosic paper by copper hydroxide nanorods for oils purification

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Ahmed S. Belal ◽  
Jehan El Nady ◽  
Azza Shokry ◽  
Shaker Ebrahim ◽  
Moataz Soliman ◽  
...  
Keyword(s):  
Contact Angle ◽  
Filter Paper ◽  
Separation Efficiency ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Absorption Capacity ◽  
Morphological Properties ◽  
Copper Hydroxide ◽  
Immersion Method ◽  
Water Contact

AbstractOily water contamination has been sighted as one of the most global environmental pollution. Herein, copper hydroxide nanorods layer was constructed onto cellulosic filter paper surface cured with polydopamine, Ag nanoparticles, and Cu NPs through immersion method. This work has been aimed to produce a superhydrophobic and superoleophilic cellulosic filter paper. The structure, crystalline, and morphological properties of these modified cellulosic filter paper were investigated. Scanning electron microscope images confirmed that the modified surface was rougher compared with the pristine surface. The contact angle measurement confirmed the hydrophobic nature of these modified surfaces with a water contact angle of 169.7°. The absorption capacity was 8.2 g/g for diesel oil and the separation efficiency was higher than 99%. It was noted that the flux in the case of low viscosity solvent as n-hexane was 9663.5 Lm−2 h−1, while for the viscous oil as diesel was 1452.7 Lm−2 h−1.

Plasma Pre-Treatment of Polyethylene Terephthalate Substrate Influence on the Properties of ZnO Thin Film

2014 ◽  
Vol 895 ◽  
pp. 41-44
Author(s):  
Seiw Yen Tho ◽  
Kamarulazizi Ibrahim
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Polyethylene Terephthalate ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Zno Thin Films ◽  
Zno Thin Film ◽  
Water Contact ◽  
Pre Treatment ◽  
Pet Substrate

In this work, the influences of plasma pre-treatment on polyethylene terephthalate (PET) substrate to the properties of ZnO thin film have been carried out. ZnO thin films were successfully grown on PET substrate by spin coating method. In order to study the effects of plasma pre-treatment, a comparison of treated and untreated condition was employed. Water contact angle measurement had been carried out for PET wettability study prior to ZnO thin film coating. Morphology study of ZnO thin film was performed by scanning probe microscope (SPM). Besides, optical study of the ZnO thin film was done by using UV-vis spectrophotometer. All the measured results show that plasma pre-treatment of PET substrate plays an important role in enhancing the wettability of PET and optical properties of the ZnO thin films. In conclusion, pre-treatment of PET surface is essential to produce higher quality ZnO thin film on this particular substrate in which would pave the way for the integration of future devices.

Fabrication and characterization of customized tubular scaffolds for tracheal tissue engineering by using solvent based 3D printing on predefined template

2021 ◽  
Vol 27 (2) ◽  
pp. 421-428
Author(s):  
Rudranarayan Kandi ◽  
Pulak Mohan Pandey ◽  
Misba Majood ◽  
Sujata Mohanty
Keyword(s):  
Tissue Engineering ◽  
Cell Adhesion ◽  
3D Printing ◽  
Chemical Properties ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
In Vitro Cytotoxicity ◽  
Content Type ◽  
Tracheal Tissue

Purpose This paper aims to discuss the successful fabrication of customized tubular scaffolds for tracheal tissue engineering with a novel route using solvent-based extrusion 3D printing. Design/methodology/approach The manufacturing approach involved extrusion of polymeric ink over a rotating predefined pattern to construct customized tubular structure of polycaprolactone (PCL) and polyurethane (PU). Dimensional deviation in thickness of scaffolds were calculated for various layer thicknesses of 3D printing. Physical and chemical properties of scaffolds were investigated by scanning electron microscope (SEM), contact angle measurement, Fourier Transform Infrared Spectroscopy (FTIR) and X-ray diffraction (XRD). Mechanical characterizations were performed, and the results were compared to the reported properties of human native trachea from previous reports. Additionally, in vitro cytotoxicity of the fabricated scaffolds was studied in terms of cell proliferation, cell adhesion and hemagglutination assay. Findings The developed fabrication route was flexible and accurate by printing customized tubular scaffolds of various scales. Physiochemical results showed good miscibility of PCL/PU blend, and decrease in crystalline nature of blend with the addition of PU. Preliminary mechanical assessments illustrated comparable mechanical properties with the native human trachea. Longitudinal compression test reported outstanding strength and flexibility to maintain an unobstructed lumen, necessary for the patency. Furthermore, the scaffolds were found to be biocompatible to promote cell adhesion and proliferation from the in vitro cytotoxicity results. Practical implications The attempt can potentially meet the demand for flexible tubular scaffolds that ease the concerns such as availability of suitable organ donors. Originality/value 3D printing over accurate predefined templates to fabricate customized grafts gives novelty to the present method. Various customized scaffolds were compared with conventional cylindrical scaffold in terms of flexibility.

Preparation of TiO2–SiO2 Hybrid Nanosols Coated Flame-Retardant Polyester Fabric Possessing Dual Contradictory Characteristics of Superhydrophobicity and Self Cleaning Ability

2020 ◽  
Vol 20 (3) ◽  
pp. 1780-1789 ◽  
Author(s):  
Priyanka Katiyar ◽  
Shraddha Mishra ◽  
Anurag Srivastava ◽  
N. Eswara Prasad
Keyword(s):  
Electron Microscopy ◽  
Contact Angle ◽  
Flame Retardant ◽  
Protective Clothing ◽  
Sol Gel ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Water Contact ◽  
Vis Spectroscopy ◽  
Self Cleaning

TiO2, SiO2 and their hybrid nanocoatings are prepared on inherent flame retardant textile substrates from titanium(IV)iso-proproxide (TTIP) and tetraethoxysilane (TEOS) precursors using a sol–gel process followed by hydrothermal treatment. The coated samples are further functionalized by hexadecyltrimethoxysilane (HDTMS) to impart superhydrophobicity. Sample characterization of the nanosols, nanoparticles and coated samples are investigated using, X-ray diffractometer, transmission electron microscopy, scanning electron microscopy, UV-Vis spectroscopy, contact angle measurement. Stain degradation test under mild UV irradiation shows almost 54% degradation of coffee stain within 4 hours measured by Spectrophotometer. UV-Vis Absorption Spectroscopy demonstrates complete degradation of methyl orange colorant within 3 hours. Hybrid nanosol coated and HDTMS modified inherent flame retardant polyester surfaces show apparent water contact angle as ~145°, which is much closer to proximity of superhydrophobic surfaces. Thus, the novelty of present work is, by using sol–gel technique, a bi-functional textile surface has been developed which qualifies the very specific requirements of protective clothing like self-cleaning property (imparted by TiO2 nanoparticles) and superhydrophobicity (imparted by SiO2 nanoparticles and further surface modification by HDTMS), which are entirely contradictory in nature, in a single fabric itself. Thus developed textile surfaces also possess the other attributes of protective clothing like flame retardancy and air permeability.

scholarly journals Application of Waterborne Acrylic and Solvent-Borne Polyester Coatings on Plasma-Treated Fir (Abies alba M.) Wood

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 370
Author(s):  
Hadi Gholamiyan ◽  
Behnam Gholampoor ◽  
Reza Hosseinpourpia
Keyword(s):  
Plasma Treatment ◽  
Treated Wood ◽  
Abies Alba ◽  
Untreated Wood ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Accelerated Weathering ◽  
Water Contact ◽  
Before And After ◽  
Carbon Dioxide Co2

This research investigates the effect of plasma treatment with air, nitrogen (N2), and carbon dioxide (CO2) gases on the performance of waterborne (acrylic) and solvent-borne (polyester) coated fir (Abies alba M.) wood samples. The properties of the plasma-coated samples were analyzed before and after exposure to accelerated weathering and compared with those of untreated and solely treated ones. According to pull-off testing, the coating adhesion of the wood samples was considerably improved by plasma treatment, and obvious differences were observed between different plasma gases. The effect was more pronounced after the weathering test. Similar results were obtained for the abrasion resistance of the samples. The water contact angle measurement illustrated more hydrophilic character in the solely plasma-treated wood in comparison with the untreated wood. The application of coatings, however, strongly improved its hydrophobic character. The performances of waterborne and solvent-borne coatings on plasma-treated wood were comparable, although slightly better values were obtained by the waterborne system. Our results exhibit the positive effect of plasma treatment on coating performances and the increased weather resistance of the waterborne and solvent-borne coating systems on plasma-treated wood.

scholarly journals High Loading Capacity and Wear Resistance of Graphene Oxide/Organic Molecule Assembled Multilayer Film

2021 ◽  
Vol 9 ◽  
Author(s):  
Li Chen ◽  
Gang Wu ◽  
Yin Huang ◽  
Changning Bai ◽  
Yuanlie Yu ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Photoelectron Spectroscopy ◽  
Multilayer Films ◽  
Thickness Measurement ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Film Structure ◽  
Silicon Substrates ◽  
Water Contact ◽  
Macro Scale

Taking advantage of the strong charge interactions between negatively charged graphene oxide (GO) sheets and positively charged poly(diallyldimethylammonium chloride) (PDDA), self-assembled multilayer films of (GO/PDDA)n were created on hydroxylated silicon substrates by alternating electrostatic adsorption of GO and PDDA. The formation and structure of the films were analyzed by means of water contact angle measurement, thickness measurement, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Meanwhile, tribological behaviors in micro- and macro- scale were investigated by AFM and a ball-on-plate tribometer, respectively. The results showed that (GO/PDDA)n multilayer films exhibited excellent friction-reducing and anti-wear abilities in both micro- and macro-scale, which was ascribed to the special structure in (GO/PDDA)n multilayer films, namely, a well-stacked GO–GO layered structure and an elastic 3D crystal stack in whole. Such a film structure is suitable for design molecular lubricants for MEMS and other microdevices.

Surface Modification of Ultra-High Molecular Weight Polyethylene with Crosslinked Hyaluronic Acid and its Antiwear Performance

2015 ◽  
Vol 642 ◽  
pp. 94-98
Author(s):  
Chau Chang Chou ◽  
Yu Hsiang Hao ◽  
Fu Yin Hsu
Keyword(s):  
Molecular Weight ◽  
Hyaluronic Acid ◽  
High Molecular Weight ◽  
Incident Light ◽  
Contact Angle Measurement ◽  
Angle Measurement ◽  
Coated Sample ◽  
Infrared Spectrometry ◽  
Water Contact ◽  
Ultra High Molecular Weight

The surface of high-pressure crystallized ultra-high molecular weight polyethylene (UHMWPE) was modified for application as an artificial cartilage material. A UHMWPE surface pretreated by a series of processes, including treatment with O2-plasma and ethylenediamine solution, was coated with hyaluronic acid (HA). After that, adipic acid dihydrazide (AAD) was added to partially crosslink the HA coating in order to enhance its durability. The modified samples were verified by water contact angle measurement and Fourier transform infrared spectrometry. Both HA layers, original and crosslinked, were also quantitatively evaluated by carbohydrate chemistry assay according to the absorbance of the incident light. The tribological performance of the samples was evaluated by a pin-on-disk test rig lubricated by normal saline under an average pressure of 18 MPa and at a sliding speed of 0.03 m/s for 45 h. The wear resistance of the HA-coated UHMWPE specimens promoted by the crosslink process was superior to that of the original HA-coated sample, and that resistance was maintained after immersion in saline solution for one month.

Sign in / Sign up

Export Citation Format

Share Document